MOOSE RACING AGROID RS-16 User manual

AGROID RS-16 E-Balance Bike
GRIP TYPE THROTTLE
USER’S MANUAL

2
BEFORE RIDING MOOSE RACING® AGROID RS-16 E-BALANCE BIKE
READ MANUAL CAREFULLY BEFORE OPERATING
Read and understand this entire manual before allowing a child to use this
product! Retain this manual for future reference.
For your records, save your original sales receipt with this manual and write down
the serial numbers. Please have your applicable product Serial Number (S/N) and
a copy of your receipt before contacting your dealer for warranty assistance and /
or replacement parts. The serial numbers are found:
• Frame: Stamped on the underside of the bike frame
• Motor: Labeled on the motor exterior casing
• Battery: Labeled on the bottom of the battery pack
NOTE: Illustrations are for demonstration purposes only. Illustrations may not
reflect the exact appearance of actual product. Specifications are subject to
change without notice.
Consult with your insurance company to verify whether your existing policy(ies)
provides necessary coverage for use of the Agroid RS-16 E-Balance Bike.
INDICATES A HAZARD, WHICH IF NOT AVOIDED COULD RESULT IN SERIOUS
INJURY OR DEATH . Many of the Warnings say a rider may lose control and fall.
Because any fall can result in serious injury or even death, this manual does not
always repeat the warning of possible injury or death.
RIDING THE AGROID RS-16 E-BALANCE BIKE PRESENTS POTENTIAL RISKS
AND CAUTION IS REQUIRED. The Agroid RS-16 E-Balance Bike is a battery-powered
product, intended to be ridden by children. It is impossible to anticipate every
situation or condition which can occur while riding, and this manual makes no
representation about the safe use of the product under all conditions. Operating
the Agroid RS-16 E-Balance Bike involves risk of injury and damage. By allowing a
child to ride the Agroid RS-16 E-Balance Bike, you are assuming the responsibility
for that risk.
ADULT SUPERVISION IS REQUIRED AT ALL TIMES THE BIKE IS IN USE.
Adult supervision is required for child riders. Adult supervisors are responsible for
supervising the rider and for ensuring the use of all safety equipment and other
precautions while operating this product.
This manual contains important safety information. It is your responsibility to
review this manual and to make sure you understand and teach child riders the
rules of safe and responsible riding, as well the proper use and maintenance of
the bike. Proper use and maintenance of the Agroid RS-16 E-Balance Bike reduces
the risk of injury.
If supervision is transferred to another adult, it is YOUR RESPONSIBILITY to
pass this user’s manual and all relevant information to whomever will be taking
on this role, and ensure, without question, that the rider is supervised, controlled,
and taught in a safe manner.

3
THIS MODEL IS NOT FOR RIDERS UNDER THE AGE OF 8 OR
HEAVIER THAN 132 LBS. (60 KG).
Any rider who exceeds the weight capacity of the Agroid RS-16 E-Balance Bike, or
who is unable to fit comfortably on the Agroid RS-16 E-Balance Bike should not
ride or attempt to ride it. No rider should ride or attempt to ride an Agroid RS-16
E-Balance Bike if they cannot sit on the seat with both hands on the handlebars
and both feet flat on the ground at the same time.
Children under the age of 8 years old should not use the Agroid RS-16 E-Balance
Bike. This recommendation is based not just on age or weight or height- it takes
into consideration the coordination and skills a rider needs for operation of this
product. The recommended minimum rider age is only an estimate and can be
affected by rider’s size, weight, development or skills. As such, not every child 8
years old or older will be suited to the Agroid RS-16 E-Balance Bike.
The decision to allow a child to ride this product should be based on the child’s
maturity, skill, and ability to follow directions and rules. Adults are instructed
not to disregard the instructions and warnings in this manual, and not to permit
children under 8 years old to ride the Agroid RS-16 E-Balance Bike. This product
is intended for use only by riders who are, at minimum, completely comfortable
and competent operating the Agroid RS-16 E-Balance Bike with adult supervision
and assistance. Riders with any mental or physical conditions that may: make
them susceptible to injury, impair their physical dexterity, or mental capacity
to recognize, understand, and follow safety instructions, impair their ability to
understand the hazards inherent in a product’s use, or impair their ability to
safely operate the Agroid RS-16 E-Balance Bike, should not use or be permitted to
operate this product if determined inappropriate for their abilities.
Adults that have inherent health issues or physical limitations should not provide
supervision to these products if such limitations would impair the ability to
provide supervision for the safe operation of this product.
Caution is also necessary in situations in which children of various ages and
abilities may have access to the same riding products.
Refer to your local laws and regulations as to any age limits or other
requirements for riding an e-balance bike as your state may have different
and more restrictive age restrictions in place from what the manufacturer
recommends.

4
THROTTLE GRIP
Monitor
Power Switch Throttle grip
COMPONENTS
1 . Throttle grip
2. Stem
3. Grip
4. Power off brake
5. Handlebar
6. Headset
7 . Fork
8. Front Wheel
9. Front axle nuts
10. Battery
11 . Footrest platform
12 . Side cover
13. Chain guard
14. Chain tension
15 . Rear axle nuts
16 . Drum brake
17 . Rear wheel
18 . Seat clamp
19 . Seat post
20. Saddle
21 . Frame
20
5
6
7
8
9
1 3 4
2
21
19
18
17
16
15
14
13 12 11 10
Chain Drive motor
Drive sprocket Electric Speed Control
THROTTLE GRIP
Monitor
Power Switch Throttle grip
COMPONENTS
1 . Throttle grip
2. Stem
3. Grip
4. Power off brake
5. Handlebar
6. Headset
7 . Fork
8. Front Wheel
9. Front axle nuts
10. Battery
11 . Footrest platform
12 . Side cover
13. Chain guard
14. Chain tension
15 . Rear axle nuts
16 . Drum brake
17 . Rear wheel
18 . Seat clamp
19 . Seat post
20. Saddle
21 . Frame
20
5
6
7
8
9
1 3 4
2
21
19
18
17
16
15
14
13 12 11 10
Chain Drive motor
Drive sprocket Electric Speed Control
COMPONENTS

5
ASSEMBLY
1. Tools/parts included: Box
end wrench (1); Hexagon
keys – (2); Footrest Platform
(1); Screws (2); Washers (2)
4. Put cap back on and tighten
screws securely with
hexagon key
8. Place footrest platform on using washer and screw. Use
hexagon key to tighten securely
7. Position “anti-off hook” on front fork as shown and tighten securely with screw nut. Tighten
screw nut securely using the box end wrench
5. Assemble front wheel to the
fork and tighten bolts securely
with box end wrench
6. Locate anti-off hook
9. Loosen the seat clamp and
adjust seat to proper height
for rider. After adjustment
has been made, tighten the
seat clamp securely using
hexagon key
2. Remove front cap from
handlebar stem using
hexagon key
3. Put handlebar on the stem
and adjust angle of handle-
bar to fit rider’s reach

6
Always be aware of and obey any local laws or regulations
which may affect the locations where the Agroid RS-16 E-Balance Bike
may be used. Keep safely away from cars and motor vehicle traffic at all
times, and only ride where allowed and with caution.
Never ride the Agroid RS-16 E-Balance Bike on public
streets, roads, highways, at night, or when visibility is limited.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Do not activate the throttle (speed) control on the hand grip unless the rider is
seated on the Agroid RS-16 E-Balance Bike, with all protective equipment on, and
is in a safe outdoor environment suitable for riding. The maximum speed of the
bike is limited by the selected power mode (see Change Speed Mode section
below). Avoid excessive speeds and downhill grades that may cause the rider to
go too fast.
Always maintain a grip on the handlebars with both hands. Do not touch the brake
drum or motor on your Agroid RS-16 E-Balance Bike when in use or immediately
after riding, as these parts can become very hot. Ride defensively. Watch out
for potential obstacles that a rider could collide with, catch the wheel, or force
a sudden swerve or loss of control. Avoid pedestrians, skaters, skateboards,
scooters, bikes, children, or animals who may enter the riding path, and respect
the rights and property of others.
The Agroid RS-16 E-Balance Bike is intended for use on flat,
dry, solid surfaces. Riding the Agroid RS-16 E-Balance Bike on surfaces with
loose debris, such as sand, leaves, rocks, or gravel could cause a rider to lose
control of the bike and fall. Wet, slick, bumpy, uneven or rough terrain may
impair traction and contribute to possible accidents, including falls. Do not
ride the Agroid RS-16 E-Balance Bike through mud, over ice, through puddles,
in wet or icy weather, as the rider could lose control of the bike and fall.
Never immerse or wash the Agroid RS-16 E-Balance Bike with
water, as the electrical and drive components could be damaged by water
or create other possible unsafe conditions.
Never use near steps, or swimming pools. Avoid sharp bumps, drainage grates,
and sudden surface changes. Do not attempt or do stunts or tricks on your
Agroid RS-16 E-Balance Bike. The Agroid RS-16 e-Balance Bike is not made to
withstand abuse from misuse, such as jumping, curb grinding, or any other
stunts. Racing, stunt riding, or other maneuvers also enhance the risk of loss of
control, or may cause uncontrolled rider actions or reactions.
Never allow more than one person at a time to ride the Agroid RS-16 E-Balance
Bike. Do not ride at night or when visibility is limited. Never use headphones, a cell
phone or texting when riding.

7
Do not ride the Agroid RS-16 E-Balance Bike indoors. Indoor settings lack
sufficient space for riding, and carpet or flooring may be damaged. Never tow
anything or anyone with your Agroid RS-16 E-Balance Bike or allow your Agroid RS-
16 E-Balance Bike to be towed by any other person or vehicle, motorized or not.
Ride your Agroid RS-16 E-Balance Bike in an open, outdoor, controlled
environment. Do not ride on public streets, open roads, or highways.
POWERED & ROTATING PARTS WARNING:
Never operate the Agroid RS-16 E-Balance Bike without the
side cover and chain guard properly installed and securely in place. Do
not allow hands, feet, hair, body parts, clothing, or other objects to come
in contact with any rotating or moving parts, wheels, drive motor, drive
sprocket, or chain while the motor is running or while the wheels and tires
are rotating.
PROPER RIDING ATTIRE:
Always wear proper protective equipment, including: a
properly fitting helmet that meets or exceeds established safety standards
(with chin strap securely buckled), eye protection, shoes that cover the
entire foot, elbow and knee pad protection. Keep shoelaces tied and out of
way from wheels, motor, and drive system. Never ride barefoot or in sandals.
Long-sleeved shirts, long pants, and gloves are recommended.
A helmet may be required by local law or regulations in your area. Approved
helmets in the USA must meet or exceed the US Consumer Product Safety
Commission (CPSC) standards and will be marked with a CPSC reference.
Riders’ safety and well-being are the utmost importance. Make sure they
wear a properly approved, and properly fitting helmet that is securely
buckled!
SAFELY APPROACHING OR RE-MOUNTING THE AGROID RS-16 WHEN UNIT IS NOT UPRIGHT
Riders should approach a downed Agroid RS-16 E-Balance Bike with caution
before use or if standing it back up (if it has been knocked over, or the rider has
fallen).
1. Ensure the bike is powered off. This may require pressing and holding power
switch for 3 seconds to turn off (LED light or screen is dark).
2. Ensure all wheels and tires along with drive train components have stopped
rotating or moving.
3. Return the bike to an upright position.
4. Inspect the bike for any damage.
5. Perform a pre-ride inspection (as outlined in this manual).
6. Have rider mount the bike, with both hands on the handlebars, seated with
both feet on the ground.
7. Press and hold power switch for 3 seconds to turn the bike on.
8. Resume riding.

8
LOADING AND UNLOADING - TRANSPORTATION OF AGROID RS-16
IN A VEHICLE
1. Ensure the bike is powered off. This may require pressing and holding power
switch for 3 seconds to turn bike off (LED light or screen is dark).
2. Remove the battery.
3. Place the bike in the vehicle. If necessary, secure the bike so that it will not
shift or move freely within the vehicle, possibly causing damage or injury to
individuals or other property in the vehicle.
4. After transporting and unloading, perform a pre-ride inspection before
operating the Agroid RS-16 E-Bike.
PRE-RIDING INSPECTION AND CHECKLIST
Before each ride, be sure to perform the following pre-ride inspection.
Safety Gear: Make sure rider is wearing the proper protective gear, such as an
approved and properly fitted safety helmet, eye protection, protective footwear
(rubber soled shoes that cover the entire foot) elbow and knee protection, etc.
Keep shoelaces tied and out of way of wheels, motor and drive system. NEVER
RIDE BAREFOOT OR IN SANDALS.
Power off: Ensure power is off (all LED lights or screen is dark) during the pre-
ride inspection and remains off until the rider is sitting on the saddle with both
feet flat on the ground and both hands gripping the handlebars.
Battery: Ensure the battery is removed and power is off before child mounts the
bike. The battery should be fully charged.
Throttle: Check that the throttle rotates freely. Ensure there are no cracks or
visible damage.
Brake: Check brake for proper function. When you squeeze the lever, the brake
should provide positive braking action. Make sure that brake is not rubbing when
lever is released. Adjust as required prior to use.
Side cover and chain guard: Ensure the side cover and chain guard are properly
installed and securely in place.
Tires and Wheels: Inspect tires for proper inflation (refer to sidewall of tire for
proper air pressure) and excessive wear. Check wheels for any “wobbling” as they
spin.
Frame, Fork, Stem, and Handlebars: Check for cracks, dents, and loose
hardware.
Hardware/ Loose Parts: Check all hardware, such as nuts, bolts, cables,
fasteners, etc., to ensure they are secure. There should not be any unusual rattles
or sounds from loose parts or broken components. If the unit is damaged, do not
ride until repaired. Reference “Warnings” listed in manual.

9
Note: The Agroid RS-16 E-Balance Bike battery consumes the most power
at start-up, so it is recommended the rider use his/her foot to help push
off when starting out. This can increase the battery life. The battery can
only be used on the Agroid RS-16 E-Balance Bike. Do not use for other
uses.
Note: The bike should be turned off and the battery removed when unit
is not in use. The Agroid RS-16 E-Balance Bike will turn off automatically
when not in use after 1 minute, to avoid battery from losing its charge.
BATTERY
CHARGING THE BATTERY:
Charge the battery completely before using the Agroid RS-16 E-Balance Bike.
When the battery is fully charged, the charger will display a solid red light
with a flashing green light.
To charge the battery, place the battery on charger which is plugged into an
outlet. The charger will display a solid red light and solid green light while
charging. The Agroid RS-16 E-Balance Bike should be turned OFF and the battery
removed when unit is not in use. If the power switch is left on, the battery loses
its charge. Do not charge outdoors.
BATTERY MAY ONLY BE CHARGED USING THE SUPPLIED AGROID
RS-16 CHARGER! DO NOT USE THIS BATTERY WITH OTHER PRODUCTS.
DO NOT CHARGE OUTDOORS.
BATTERY STATUS – Displayed on LED Monitor (handlebars)
F
E
F
E
F
E
F
E
100% 75% 50% 25%

10
• Solid red; flashing green = Fully charged
• Solid red; solid green = Charging
• Flashing red = Too hot/cold to charge
• Flashing red; flashing green = Battery is defective
CHARGER INDICATOR LIGHTS – (Located on battery charger)
BATTERY INSTALLATION:
Note: The Agroid RS-16 E-Balance Bike should be turned OFF and the battery
removed when unit is not in use. If power switch is left on, the battery loses
its charge.
1. Turn the handlebars 45 degrees to give extra room to insert the battery.
2. Locate the battery and position it as shown. [Figure A]
3. Slide the battery into slot on the front side of down tube of the bike.
[Figure B]
4. There is a point where the battery release latch/ button provides some
resistance. Push the battery past this point for secure connection. You
should hear a click, and the gap should be closed. [Figure C]. If the battery
is not fully seated (with click), the bike will not operate.
BATTERY REMOVAL:
1. Turn handlebars 45 degrees to give extra room to remove battery.
2. Press the battery release latch/ buttons and slide battery out of slot in the
direction shown.
A.
B. C.

11
BATTERY DISPOSAL:
The Agroid RS-16 E-Balance Bike uses a sealed lithium cell battery. DO NOT
dispose of a lithium cell battery in a fire; the battery may explode or leak. DO NOT
dispose of a lithium cell battery in your regular household trash. The incineration,
land filling or mixing of sealed lithium cell batteries is prohibited by law in most
areas.
These lithium batteries must be recycled or disposed of in an environmentally
safe manner. Return exhausted batteries to a federal or state approved lithium
cell battery recycler or a local battery retailer who accepts them for recycling.
Many states have laws prohibiting the disposal of lithium cell batteries in
municipal waste stream. Check your local and state law.
OPERATION
POWER ON/OFF
Power on: Press and hold power switch for 3 seconds then you will hear a long
beep tone.
• (1) One Beep tone: Low speed 5 MPH (8Km/H) (Default Mode)
• (2) Two beep tones: Middle Speed 7.5 MPH (12Km/H)
• (3) Three beep tones: High speed 11 MPH (17.6Km/H)
Power Off: Press and hold power switch for 3 seconds then you will hear a long
beep tone one time. The monitor or LED display will go dark.
Note: The Agroid RS-16 E-Balance Bike will turn off automatically when not in use
for 1 minute, to avoid battery losing its charge.
CHANGE SPEED MODE
(To be performed only by adults)
Note: The speed mode settings can only be changed when the Agroid RS-16
E-Balance Bike is stopped and the hand brake is fully engaged.
The Agroid RS-16 E-Balance Bike has 3 different speed modes riders of differing
skill levels- Low, Middle, and High. Do not permit or show children how to adjust
the modes. Each child rider should have the speed set by an adult that will be
closely supervising the child. DO NOT advance a rider to a faster speed mode
without learning and demonstrating mastery of the slower speed settings.
1. Press and hold the brake lever.
2. Press the power switch twice in quick succession (in 1 second). You will hear a
beep tone indicating which mode the bike is currently set.
• One beep tone is Low speed 5MPH (8Km/h)
• Two beep tones is Middle speed 7.5 MPH (12Km/h)
• Three beep tones is High Speed setting 11 MPH (17.6Km/h)
3. To change to the next speed setting, press the power switch twice in quick
succession (twice within 1 second). Speed setting will advance to the next
setting. Repeat this step as needed to select the desired speed setting. The
speed settings will cycle through in the order described above.

12
RIDING THE AGROID RS-16 E-BALANCE BIKE
(Perform under adult supervision, while wearing protective equipment, in an
open and safe area)
Riders should practice and master riding in the non-powered mode before
starting to ride the Agroid RS-16 E-Balance Bike in any powered mode.
Non-Powered Training:
1. Ensure the Agroid RS-16 E-Balance Bike is powered off (see Power On/Off
Section above) with battery removed.
2. Rider should sit on bike with both hands on the handlebars and both feet
flat on ground. Make sure the rider is aware of the location of the seat, foot
platform, brake, handlebars, throttle, and their functions.
3. Rider should use his/her feet to push the bike around, learning balance and
confidence.
4. Rider should progress to coasting on the bike with feet on the platform, and
practice controlled turning.
5. Rider should learn to brake to a safe stop using hand brake while maintaining
control.
6. As the rider’s skill and confidence increases, he/she can practice standing
(using the foot platform) and stopping while maintaining control without falling.
Is Your Rider Ready to Move on to Powered Mode? Here’s a Qualifying
Checklist:
• Can rider push and coast safely with feet on platform?
• Can rider maintain control while standing on platform?
• Can rider control bike from start to stop?
• Can rider use hand brake to stop on command?
• Can rider coast and turn while navigating mild hills and obstacles?
• Has rider demonstrated enough control to move to power riding without
being a risk to themselves and others?
•Only after rider has command of the above skills, move to power mode.
Power Mode Training:
Low speed (Beginner)
1. Ensure Agroid RS-16 E-Balance Bike is powered off with battery removed.
2. Once rider has mounted the Agroid RS-16, E-Balance Bike install battery.
3. Press and hold power switch 3 seconds to turn on.
4. Ensure you hear one beep tone (signifying Low speed). If not, see CHANGE
SPEED MODE sections in this manual.
5. Have rider carefully push the Agroid RS-16 E-Balance Bike forward and practice
slightly twisting the throttle to learn to feel the Agroid RS-16 E-Balance Bike
beginning to move forward under power.
6. With feet on ground, have rider slowly increase throttle use until moving
forward balancing on their own.
7. Have rider practice rolling throttle on and off as well as safe stops with hand
brake.

13
8. As rider gains balance and demonstrates throttle and brake skills, advance to
riding with feet on platform.
9. Coach rider to maintain a safe distance from obstacles and other riders.
Middle Speed (Intermediate) – Requires satisfactory command of Agroid RS-16
E-Balance Bike operation at Low Speed (as described above). Use caution, the
top speed and acceleration functions have increased in this mode.
1. Ensure Agroid RS-16 E-Balance Bike is powered off with battery removed.
2. Once rider has mounted the Agroid RS-16 E-Balance Bike, install battery.
3. Press and hold Power switch for 3 seconds to turn on.
4. Ensure you hear two beep tones (signifying middle speed). If not, see CHANGE
SPEED MODE section in this manual.
5. Adult should supervise child riders as the top speed and acceleration functions
have both increased in this mode.
6. Coach rider to demonstrate ability to roll off throttle, use brake to slow to a
stop, and maintain a safe distance from obstacles and other riders.
7. A majority of users will find this speed to be adequate for significant skill
building.
High Speed (Advanced) Requires satisfactory command of Agroid RS-16
E-Balance Bike operation at Low and Middle Speeds (as described above). Use
caution, the top speed and acceleration functions are at maximum in this
mode.
1. Ensure Agroid RS-16 E-Balance Bike is powered off with battery removed.
2. Once rider has mounted the Agroid E-Balance Bike RS-16, install battery.
3. Press and hold Power switch 3 seconds to turn on.
4. Ensure you hear three beep tones (signifying High speed). If not, see CHANGE
SPEED MODE section in this manual.
5. Coach rider to demonstrate ability to roll off throttle, use brake to slow to a
stop, and maintain a safe distance from obstacles and other riders.
6. This mode is for advanced and older riders only.
Failure to use common sense and heed the above warnings
increases the risk of serious injury. Use with appropriate caution and
serious attention to safe operation.

14
PRODUCT PARTS
Contact Moose Racing for assistance with replacement parts. For a list of
available replacement parts, or to locate an authorized dealership within your
area, visit our website: www.mooseracing.com.
MOOSE AGROID RS-16 E-BALANCE BIKE LIMITED WARRANTY
Moose Racing warranties this product to be free from material and
manufacturing defects from date of purchase as described below.
• Frame and Fork - 3 Years
• Non-electrical systems components – one year
• Electrical system components, including battery and charger – 180 days
• Normal wear and tear items- 30 days. (Sprocket, chain, grips, bar plugs,
saddle, footrest, brake cable/housings, brake lining, tires)
This limited warranty will be void if the product is not used in accordance with the
user’s manual or:
• Is damaged in an accident, crash, or loss of control incident.
• Is used in a manner other than for recreation.
• Is poorly or incorrectly maintained.
• Is used in a manner in which this product was not specifically designed.
• There has been a failure to follow user’s manual instructions or warnings.
• The electronics or battery are exposed to water.
• The product or components are modified in any way.
• The product is damage by unauthorized service or parts.
• The product is used for commercial purposes.
This limited warranty does not cover any damage, failure or loss caused by
improper assembly, maintenance, or storage.
Moose Racing is not liable for incidental or consequential loss or damage due
directly or indirectly to the use or misuse of this product.
This limited warranty is valid only for original purchaser and is non-transferable.
Warranty claims must be accompanied with original proof of purchase and
applicable serial number(s). If proof of purchase is not provided, the warranty
period begins from original date of manufacture.
Moose Racing does not offer an extended warranty.

15
For your records, save your original sales receipt with this manual and write down
the serial numbers. Please have your applicable product Serial Number (S/N) and
a copy of your receipt before contacting your dealer for warranty assistance and /
or replacement parts. The serial numbers are found:
• Frame: Stamped on the underside of the bike frame
• Motor: Labeled on the motor exterior casing
• Battery: Labeled on the bottom of the battery pack
QUESTIONS?
Contact Moose Racing by visiting our website www.mooseracing.com with
questions about the Agroid RS-16 E-Balance Bike, assembly, replacement parts,
or dealer locations.

16
This product can expose you to Di(2-ethylhexyl)phthalate (DEHP) which is known
to the State of California to cause cancer, birth defects or reproductive harm.
For more information, go to www.P65Warnings.ca.gov.