Morgan MAC-080 DANDELION User manual

USER MANUAL
MAC-080 DANDELION
E-mail: [e-mail]
www.morgan.my
Market Expansion
Services by
www.dksh.com.my
facebook.com/morganappliances
Port ble Air
Conditioner

3
IMPORTANT SAFEGUARDS
When using electric appliances, basic safety precautions should always be followed
including the following:
1. Read all instructions carefully and retain them for future reference.
2. Before connecting to the power supply, be sure to follow local power requirements when
installing the portable air conditioner and ensure that it is properly grounded. If you have
any question on electrical installation, follow the instructions of the manufacturer, and if
necessary, ask a professional electrician to install it.
3. Always disconnect appliance from the power supply when not in use or before cleaning.
4. Always attach the power cord to the appliance BEFORE connecting it to the power
supply. To disconnect, switch off appliance first before detaching the power plug from
the power supply.
5. Close supervision is necessary when any appliance is used by or near children.
6. This portable air conditioner is suitable for indoor use only, and not for other
applications.
7. For best performance, place the machine on a stable surface, in a dry area while
allowing a distance of over 50cm between the machine and the surrounding objects or
walls.
8. Ensure that the power plug is securely connected to the power supply and the power
cord is safely tucked away to prevent accidental tripping over.
9. Do not insert any foreign objects into the air inlet and outlet of the unit. Keep air inlet
and outlet free from obstructions.
10. Do not operate appliance with damaged power cord or power plug or after the appliance
malfunctions or has been damaged in any manner. In such a situation, it is
recommended to return the appliance to your nearest Authorized Service Centre for
examination, repair, or adjustment.
11. The use of accessory attachments not recommended by the appliance manufacturer
may cause hazard or injury.
12. Ensure the installed drainage pipes are properly connected and are not distorted or bent
in any manner. Use hands to gently adjust the air outlet’s upper and lower wind- guide
strips to avoid damaging the wind-guide strips.
13. Ensure unit is in an upright position when moving it.
14. Place unit away from gasoline, stoves, flammable gas and other heat sources.
15. Do not attempt to disassemble, modify or repair the unit yourself to avoid machine
malfunction and/or personal injuries and damage to property.
Thank you for purchasing a quality MORGAN appliance. We trust that you will have a
pleasant experience with your new product. To guarantee safety and best efficiency,
please read this manual carefully and keep a copy for future reference.
FOR HOUSEHOLD USE ONLY
2
C O N T E N T S
3
4
5
6
8
10
11
12
12
13
15
I PORTANT SAFEGUARDS
FEATURES
PARTS IDENTIFICATION
INSTALLATION AND ADJUST ENT
OPERATING INSTRUCTIONS
DRAINAGE INSTRUCTIONS
CARE & CLEANING
STORAGE
SPECIFICATIONS
TROUBLESHOOTING
SCHE ATIC DIAGRA

4
IMPORTANT SAFEGUARDS
5
PARTS IDENTIFICATION
1
2
3
4
5
6
7
16. Do not install and use the unit in the bathroom or other humid environments.
17. WARNING: Do not yank on the power plug to turn off the unit to prevent short circuits
and/or personal injuries.
18. Do not place cups or other objects on top of the unit to prevent water or other liquids
from spilling into the unit’s internals.
19. Do not spray insecticide or other flammable substances on/near the unit.
20. Do not wipe or wash the unit with chemical solvents such as gasoline and alcohol.
21. Always power off the unit before cleaning the unit.
22. The unit can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children are advised not to play with the unit nor should they be allowed to
clean and maintain it without supervision.
1. Control Panel
2. Air Outlet / Louver
3. Front Housing
4. Top Cover
5. Handle
6. Rear Housing
7. Caster
8. Air Vent
9. Rear Housing
10. EVA Filter
11. Continuous Drainage
Outlets
12. CON Filter
13. Drainage Outlet
FEATURES
• New look, compact structure, streamlined design with luxurious feel.
• Cooling, dehumidification and fan function.
• Continuous Water Drainage Functions.
• Control panel with LED display.
• User-friendly remote-control design.
• Smooth heat dispersion system for optimum cooling performance.
• Air filtration capability.
• Timing switch function.
• Auto restart protection function upon restarting the compressor after three minutes.
9
8
10
11
12
13
Exhaust Pipe Assembly
Window Sealing Plate Assembly

INSTALLATION AND ADJUSTMENT
7
2.Elongate the exhaust pipe and snap its flat end into the window sealing plate crevice
assembly (Fig.5 & Fig.6).
NOTES:
• The flat end of the exhaust pipe joints must be snapped into place.
• The pipe cannot be distorted nor bent (greater than 45 °).
• Ensure the exhaust pipe’s ventilation is free from any obstruction.
IMPORTANT
• The length of the exhaust hose is 280~1,500mm, based on the unit’s specifications.
• Do not use extension tubes or replace it with other different hoses, or this may cause a
malfunction.
• The exhaust hose must be not obstructed to prevent overheating.
INSTALLATION
WARNING: before using the portable air conditioner, keep it upright for at least two
hours.
• The portable air conditioner can be easily moved anywhere around the house.
• When moving, ensure that the unit is in the upright position and placed on a flat, stable
surface.
• Do not install and use the air conditioning in the bathroom or other humid environments.
A. Install the heat pipe assembly
secure the heat pipe assembly (exhaust fitting end) into the exhaust port on the rear panel.
(Fig.1)
B. Install the window sealing plate assembly
1.Half open the window and mount the window sealing plate assembly to the window
(Fig.2 & Fig.3); the assembly can be placed in horizontal and vertical direction.
2.Pull the window sealing plate assembly components open, adjust their opening distance
to bring both ends of the assembly into contact with the window frame.
3.Fix the components of assembly and install the window sealing plate assembly
C.Install the body
1. ove the machine with installed heat
pipe and fittings to the window with an
allowable distance of at least 50cm
between the body, walls or other objects
(Fig.4).
6
INSTALLATION AND ADJUSTMENT
PUSH
(Fig.1)
(Fig.2)
(Fig.4)
(Fig.3)
(Fig.5) (Fig.6)

8 9
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
LED CONTROL PANEL
1. A buzzing tone will play when the unit is powered on for the first time before entering
into standby mode.
2. POWER KEY: Turns the unit ON/OFF.
3. MODE SELECTION KEY: In the case of power on, press the key to switch between
cooling → dehumidifying → fan mode.
4. UP KEY and DOWN KEY: press the two keys to change the setting temperature or
setting time, operate as follows:
- While setting temperature, press up key or down key to select the required
temperature (not available in fan or dehumidifying mode).
- While setting time, press up key or down key to select the required time.
5. WIND SPEED SELECTION KEY:
- In cooling mode, press the key to select high and low wind speed.
- In fan mode, press the key to select high and low wind speed.
6. In dehumidification mode, pressing the key is invalid, and the fan will forcibly choose
low wind speed operation.
1. High Speed
2. Sleep ode
3. Down Selection Key
4. Power Key
5. Up Selection Key
6. Timer Key
7. Water-full Indicator
8. Auto Swing Key
9. Cool
10. Dehumidifier
11. Display Window
12. Fan ode
13. Low Speed
7. TIMER KEY:
- When power on, press the key to close timer; When power off, press the key to open
timer.
- Press the key, when the timing symbol flashes, press up and down key to select the
required timing value.
- Timing values can be set in 1-24 hours and the timing value is adjusted up or down
by one hour.
8. SLEEP MODE:
In cooling mode, press the UP and Fan Key to turn on the sleep mode for Energy-
Saving and silent operations.
NOTE: DO NOT turn on the sleep mode when operating in dehumidifying or fan mode.
REMOTE CONTROL
Instructions of key operation of the high-quality remote control are as follows:
1.( ) Powers the unit ON/OFF
2.( ) Timer setting key
3.( ) Down key to reduce temperature and set timer
4.( ) Up key to increase temperature and set timer
5.( ) ode key to switch between cooling, dehumidifying, fan mode
6.( ) Fan key to select between high, low wind speeds
7.( ) Sleep key to turn on the sleep mode
PROTECTION FUNCTIONS
FROST PROTECTION FUNCTION
• In cooling, if the temperature of the EVA pipe sensor is too low,
the machine will automatically enter protection mode.
• If the temperature of the EVA pipe sensor rises to a certain temperature,
it will automatically revert to normal operation.
OVERFLOW PROTECTION FUNCTION
• When water in the water pan exceeds the maximum level, the unit will automatically
sound an alarm.
• The W.F indicator will flash on the control panel to alert you to drain the water (see
Drainage Instructions at the end of this chapter).
• After the water is emptied, the machine will get into standby status.
43 21567
8
9101112
13

10 11
OPERATING INSTRUCTIONS DRAINAGE INSTRUCTIONS
AUTOMATIC DEFROSTING
• In heating, the unit has automatic defrosting function. After defrosting, the machine will
automatically return to standby status.
OVERHEAT PROTECTION
• To protect the unit’s service life, the overheat protection protects the compressor and the
lower motor from overheating by ceasing operation.
• The unit will revert to standby mode once the unit recovers.
COMPRESSOR PROTECTION FUNCTION
• To increase the service life of the compressor, it has a 3-minute delay booting protection
function after the compressor is turned off.
CONTINUOUS DRAINAGE
(optional - applicable to dehumidifying mode
only), as shown in figure above:
1.Unscrew the drainage cover and unplug the
water plug.
2.Secure the drainage pipe into the water outlet.
3.Connect the drainage pipe to a bucket/pail.
CARE & CLEANING
IMPORTANT: Power off the unit and detach power plug from the power supply before
performing cleaning and maintenance.
CLEANING THE UNIT’S EXTERIOR
• Clean with surface of machine with a wet soft cloth.
• Do not use abrasive chemicals such as benzene, alcohol, gasoline, etc.; otherwise as
these may damage the unit’s exterior surface and finishing.
CLEANING THE FILTER SCREEN
• The unit will not operate optimally if the filter screen is clogged with dust.
• It is recommended to clean the filter screen once every two (2) weeks.
CLEANING THE UPPER FILTER SCREEN FRAME
• Clasp the wedging block of the EVA filter screen
frame with hands.
• Force down from the outside to remove the EVA
filter screen frame.
• Detach the four screws securing the EVA filter
screen and the rear housing to remove the
EVA filter screen (as shown in the above figure).
• Place the EVA filter screen into warm water with
neutral detergent (about 40°C / 104°F)
and dry it in the shade after rinsing clean.
DRAINAGE INSTRUCTIONS
MANUAL DRAINAGE
1.When the machine stops after the water pan is full, power off the machine power and
unplug the power plug from the power supply.
NOTE:
ove the machine carefully so water inside the water pan is not spilled at the
bottom of the unit.
2.Place the water container below the side water outlet behind the unit.
3.Unscrew the drainage cover and detach the water plug so water will automatically flow
into a bucket/pail.
NOTE:
• Store the drainage cover and the water plug properly.
• During drainage, the unit can be tilted slightly backwards.
• Discard any excess water before the water container is to prevent water from flowing
to the floor or carpet.
4.After discarding water, secure the water plug
and tighten the drainage cover.
NOTE:
Restart the machine after installing the water
plug and drainage cover otherwise excess
water will flow to the floor or the carpet.

12 13
• Detach the drainage cover, unplug the water plug, and thoroughly discard water remnants
in the water pan by tilting the unit.
• Power on the unit.
• Adjust it to low-wind ventilation mode and maintain this function until the drainage pipe
becomes dry to prevent mildew from forming.
• Turn off the unit, detach power plug from the power supply, and wrap the power cord
around the wrapping post,
• Attach the water plug and the drainage cover.
• Detach the exhaust pipe and store it properly.
• Cover the unit with a plastic bag and store in a dry place away from dust and children’s
reach.
• Remove batteries of the remote-control and store them properly.
WARNING: Do not attempt to alter, disassemble, modify or repair the unit yourself to
prevent personal injuries, damage to property and voiding the warranty.
Problems Possible Reasons Recommended Solutions
Th r is no pow r supply. Pow r on th unit aft r conn cting it to th
pow r supply.
Th wat r-full indicator is flashing Discard th wat r insid .
on th control pan l.
The unit is not Th ambi nt t mp ratur is too It is r comm nd d to op rat th unit at
operating low or too high. 7-35°C (44-95 °F).
• In cooling mod , th room
t mp ratur is low r than th Chang th s t t mp ratur .
s t t mp ratur .
In d humidification mod , th Th unit is plac d in a room with ambi nt
ambi nt t mp ratur is low. t mp ratur xc ding 17 °C (62 °F).
Th r is dir ct sunlight in th room. Draw th curtain.
• Doors or windows ar op n. • Clos doors and windows.
Temperature is not
• Too many p opl in th room.
cool enough • Too many h at sourc s. • Incr as cooling l v ls.
Filt r scr n is dirty & obstruct d. Cl an or r plac th filt r scr n.
Air inl t and/or outl t is obstruct d. Cl ar obstructions.
Noisy operation Th unit is not plac d on a flat & Plac th unit on a flat and stabl surfac to
stabl surfac . r duc nois & vibrations.
Compressor not Ov rh at prot ction starts. Wait for 3 minut s for th t mp ratur to
operating normaliz & th n r start th unit.
Distanc b tw n th unit and th • Dir ct th r mot -control clos r to th unit.
r mot -control is too far.
Remote control not R mot -control not align d to th • Ensur r mot -control dir ctly fac s th
working r mot -control r c iv r. r mot -control r c iv r.
Batt ri s ar d ad. R plac batt ri s.
STORAGE TROUBLESHOOTING
SPECIFICATIONS
MODEL NO. MAC-080 DANDELION
RATED VOLTAGE 220-240V~
FRE UENCY 50/60HZ
RATED WATTAGE 900W

14 15
• Refer to the product specification nameplate for technical and specifications.
• The manufacturer reserves the right to alter, improve and/or modify specific design,
features and functions without giving prior notice as part of its continuous improvement
exercise.
CORRECT DISPOSAL OF THIS PRODUCT
This marking shown on the product or its literature indicates that it should not
be disposed with other household wastes at the end of its working life. In
order to prevent any possible harm to the environment or human health from
the uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where purchasing this product from or
their local government office for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
FOR SINGLE COLD PRODUCT
TROUBLESHOOTING SCHEMATIC DIAGRAM
Problems Possible Reasons Recommended Solutions
'E1' error code Th room t mp ratur s nsor is Insp ct th room t mp ratur s nsor and
abnormal. r lat d circuitry.
'E2' error code Th pip t mp ratur s nsor is Insp ct th pip t mp ratur s nsor and
abnormal. r lat d circuitry.
NOTE: Contact the authorized service agent or similarly qualified professionals to
inspect the unit even after the recommended solutions do not work.