Morgan MWM-7 Zircon User manual

E-mail: [e-mail]
www.morgan.my
Market Expansion
Services by
www.dksh.com.my
facebook.com/morganappliances
USER MANUAL
MWM-7 Zircon
Automatic
Washing
Machine

3
PARTS IDENTIFICATION
2
C O N T E N T S
3
4
6
6
8
10
11
12
13
14
15
16
17
18
PARTS IDENTIFICATION
SAFETY AND PRECAUTIONS
INSTA ATION & ADJUSTMENT
USING THE DRAIN HOSE
WATER IN ET INSTA ATION
PREPARATION BEFORE OPERATION
OADING AUNDRY
DETERGENT GUIDE
CONTRO PANE & FEATURES
OPERATING INSTRUCTIONS
CARE & C EANING
TROUB ESHOOTING
OTHER FUNCTION
SPECIFICATIONS
Top Lid
Top Frame
Lint Filter
Control Panel
Inner Tub
Pulsator
Body
Base
Feed Valve
Power Cord
Drain Hose
Fixing Foot x 3 pcs
B
Back Cover
Adjustable Foot
Handle
Drain Valve Stopper
ACCESSORIES
ABOUT THE SAFETY SYMBOLS
Base Cover (1 pc) D
+
+
+
+
Connect this end to
the machine
Connector for
water inlet hose
and tap
water inlet hose connector
Water Inlet Hose (1 pc)
T
Drain Hose (1 pc)
Drain Hose Clip (1 pc)
T
Tapping Screw
ST4X14 (2 pcs)
B
WARNING SYMBOL
Pay special attention to the warning
symbols. There may be serious
risks to personal body safety or
damage to the appliance if warnings
are not followed.
ROHIBITION SYMBOL
This symbol strictly prohibits
action(s) that may be dangerous to
your personal safety and/or may
damage the appliance.

5
SAFETY PRECA TIONSSAFETY PRECA TIONS
4
Earth
wire
Ventilation holes
at the bottom
Soft item
Insert power plug into an earthed rated
220-240V AC power supply.
Always unplug from power supply & turn off
water when not in use, or when cleaning or
moving the appliance. Do not touch power plug
with wet hands.
Do not bend or twist the power cord in any
manner. Do not operate appliance with damaged
power cord or power plug or after the appliance
malfunctions. Contact your Authorized Service
Centre for examination, repair, or adjustment.
Ensure the pin of the
power plug is clean &
wipe with cloth if
dirty.
• Do not install the appliance in the bathroom or
damp places.
• Do not splash water on it or place wet clothes
on the control panel.
Do not wash with water hotter than 50ºC. If placed on carpeted floor, adjust the fixing feet
to allow air to flow freely.
Do not wash raincoat, motorcycle cover, feather
dress or waterproof apparels as these may
cause the appliance to vibrate abnormally
during operation.
• Do not share the same power socket or use
an extension socket.
• Do not use a damaged or loose power socket.
• Do not insert hands into the machine during
operation, even during slow speeds.
• Never allow children to play on or near the
machine during operation.
It is dangerous to alter the specifications or
modify this appliance in any manner.
Do not overload the appliance or place any hot
items such as hot kettle on the washing machine.
Do not wash garments which have been in
contact with volatile petroleum products.
• Do not leave children unattended near the
washing machine.
• Do not allow children to play with the washing
machine.
Keep the appliance away from direct sunlight
and other heat sources which may damage it.
Always clean the lint filter to prevent lint from
obstructing the cascade outlet during washing.
Ensure proper installation after every clean.
Do not place hard objects such as coins, safety
pins, nails, screws, or which can damage the
machine.
• Ensure water tap is turned on and inlet hose
is properly installed before washing.
• It is recommended to use low suds & high
efficiency laundry detergent.
⊳⋯
⊳⋯
䞈㋴㤥
Close Open

7
6
INSTALLATION & ADJ STMENT
SING THE DRAIN HOSE
It is important to install and adjust the machine according to the requirements of
the manual for your safety and correct operation
NPACKING
• Unpack the carton and retrieve the bottom panel.
• Open the top lid of the machine and remove all accessories. Remove all wrappers, including the
polystyrene base.
• It is recommended to keep the packaging for reuse in case the machine is to be transported again.
INSTALLING THE BOTTOM COVER
• ean the machine forward gently and insert the bottom cover (the side
with instructions) into the notch along arrowhead direction.
• Fix the bottom cover on the washing machine base with two tapping
screws in the provided accessories by using a cross screwdriver.
POSITIONING
The distance between the washing machine and the wall should preferably exceed 50mm, and the
maximum allowed angle of the shank base of the machine is 1º. Slanting or uneven ground may cause
operation to stop. It is recommended to adjust with the
following methods:
Make it horizontal
Use a tied thread with plumb to ensure it is horizontal.
Adjust the adjustable feet
• ift the adjustable foot gently, loosen the adjustable nut
and twist the adjustable foot.
• Fasten the nut after adjustment.
Notch
Bottom panel
The baffleplate
(
CHANGING THE DIRECTION OF THE DRAIN HOSE
1. Detach the drain hose and clip from the connector. Place the machine front side down on a soft mat
on the floor. Unmount the screws on the back cover using a screwdriver and detach the back cover.
Unmount the screw fixed to the drain hose
connector (on the right of washing machine) and
loosen the drain hose connector.
2. Detach the drain hose using reasonable force
and drain hose hoop (on the right of washing
machine). oosen the inner drain hose.
3. Detach the drain hose gate stopper (left side of the machine fixed on
washing machine base with two clips).
4. Place the inner drain hose to another side. Do not distort the inner drain
hose. Fix inner drain hose with drain hose hoop and drain hose
connector. Stand the washing machine gently and secure the back
cover with screw and install the drain hose and clip into the drain
hose connector.
WATER DRAINAGE
To ensure the drain hose drains smoothly:
1. The height of the drain hose should be less
than 10cm to ensure proper drainage.
2. Do not step on or distort the drain hose.
3. Cut the drain hose if it is too long. Cut the
front end of the drain hose slant to ensure
drainage is smooth.
4. Purchase a longer hose for longer drainage
with diameter not less than 30mm and
length not exceeding 1.5m.
5 Cut at Points A or B if the additional drain
hose is too long.
Drain hose connector Drain hose
Drain hose clip
Drain hose hoop
Drain hose gate stopper
D
<10cm
≤1.5m
≥ø30mm
<
AB
The baffleplate
(
Loosen Fasten
Adjustable
nut
Adjustable
foot
High Low
G
The baffleplate
(
SING THE DRAIN HOSE
INSTALLING THE DRAIN HOSE
• Set the drain hose clip into the drain hose to 2-3cm (from the end of the drain hose without the pot
hook).
• Install the drain hose into the correct drain hose connector and fix the drain hose connector with the
clip.
• Attach drain hose clip on the machine cabinet.

WATER INLET INSTALLATION WATER INLET INSTALLATION
TAP SELECTION
Ensure front end is longer than 10mm & tap exit end face is flat and smooth to avoid leakage.
CONNECTING THE INLET HOSE CONNECTOR WITH THE WATER TAP
1. Press the lower end of the lock lever and push down the slider. Remove inlet hose connector from
the inlet hose (see illustration 1).
2. oosen the four bolts on the inlet hose connector to access the tap. Then set the inlet hose connector
to the tap (see illustration 2)
Note: If tap calliper is unable to fit into the inlet hose end, unscrew the four bolts and remove
the bushin .
Important: Tap exit end must be flat otherwise it will leak (see illustration 3).
CONNECTING INLET HOSE TO THE WASHING MACHINE
1. Do not remove the water absorption
cushion.
2. Inspect if water absorption cushion is
dropped or damaged before every
operation.
3. If it is, contact your authorized service
agent immediately.
4. Attach the inlet hose nut on the inlet valve connector.
5. Fasten the inlet hose nut and swing it gently to make secure the connection.
CONNECTING INLET HOSE CONNECTOR WITH THE INLET HOSE
1. Push down the slider & insert the inlet hose into the connector.
2. Hang the lock lever to the inlet hose connector and release the slider
until a click sound is heard.
CHECK CONNECTION BETWEEN INLET HOSE
CONNECTOR & TAP
1. Swing the inlet hose gently to ensure it is fastened & secure.
2. After installation, turn on tap to inspect for leaks.
3. Do not bend/twist or distort the inlet hose.
4. Inspect proper connection between inlet hose
connector and the tap before every operation.
5. Ensure they are secure to prevent & not loose.
DISMANTLING INLET HOSE
1. Turn off the tap.
2. Press the locking lever, push down slider & detach inlet hose.
3 eave inlet hose connected to the tap if machine is used frequently to
prevent damaging the fixing screws.
3. Fasten the four bolts in the inlet hose connector evenly (see illustration 4).
4. Turn the fastening nut (see illustration 5).
Note: Before turnin the fastenin nut, ensure threadin is about 4mm above the upper
surface of the nut and less than 2mm above the upper surface of the nut after securin
(see illustration 6).
98
Recommended Tap Not recommended tap
(Illustration 1)
(Illustration 4) (Illustration 5) (Illustration 6)
(Illustration 2) (Illustration 3)

PREPARATION BEFORE OPERATION LOADING LA NDRY
PREPARATION BEFORE WASHING
1. Connect the inlet hose and turn on the tap.
2. This appliance must be properly earthed before connecting to the power supply. Do not link the earth
terminal gas or tap pipeline, and so forth.
3. ay down the drain hose.
Warnin : Water temperature should not exceed 50°C!
IT IS IMPORTANT TO NOTE THE FOLLOWING BEFORE LA NDRYING:
• The machine's washing and spinning capacity refer to the largest weight of standard laundry under
dry condition. Washing quantity shall be lower than the rated capacity.
• Different thickness, size and laundry type will influence the actual washing
capacity. It is ideal that laundry can be overturned normally during washing.
• Do not select high water level when laundry is less than 1.0kg to avoid water
splashing.
LA NDRY REFERENCE G IDE
• Ensure laundry is washable.
• IMPORTANT: Wash new coloured clothing separately when washing for the first time and do not wash
white clothing with coloured ones.
• Immerse non-absorbable laundry by hand.
• Treat stubborn stains such as fruit, wine, grass, rust etc. with specially formulated pre-wash detergent
before laundrying.
• Overturn the nap fabric and long floss laundry before putting them into the machine.
• Do not place chemical-soaked laundry directly into the machine.
• Place small items such as handkerchiefs, ribbons, socks etc. into laundry bag or pillow case.
1110
Check whether
there are
special
requirements for
laundrying.
Knot long
bands, fasten
buttons and
zippers.
Do not
overload
machine. oad
laundry loosely
alternating
larger items
with smaller
ones.
Sort laundry
according to fabric
type. colourfastness,
and soil level. Place
thin fabric, woollens
and those prone to
wear and tear into
laundry bag.
Ensure all pockets
are empty of small
objects such as
coins, keys, screws
etc. as these may
damage the drain
pump.
(Cotton)
(
(Cotton)
(
Blanket (Cotton)
(approx. 900g)
Work clothes (above,under)
(approx.1200g) Jeans (approx. 800g)
Coat (Cotton)
(approx. 800g)
Jacket (Cotton)
(approx. 800g)
Single bed sheet (Cotton)
(approx. 600g)
Socks
(approx. 50g)
Underpants
(approx. 70g)
Undershirt (Cotton)
(approx.180g)
Shirt (Cotton)
(approx. 300g)
Pyjamas (Cotton)
(approx.200g)

• Pour powdered detergent into the tub (see figure below).
• Close the top lid.
• It is recommended to use low suds, high-efficiency powdered detergent.
SING POWDERED DETERGENT
Dissolve powdered detergent directly in machine (not suitable for delay program):
• Select ow water level.
• Add powdered detergent and run for 30 seconds to dissolve it completely.
• Place laundry & select suitable water level program.
Dissolve powdered detergent prior to washing:
• Prepare warm water (30 C) in a container.
• Pour powdered detergent while stirring to fully dissolve it.
• Do not use too much powdered detergent as it may discolour clothes and not rinse out completely.
• Inferior quality powdered detergent may cake if not used for some time.
• It is recommended to clean the detergent drawer frequently for best washing results.
SING BLEACH
• Fill water to the selected level, dilute the bleach in the container.
• Slowly pour into the washing tub.
• Do not use bleach for coloured or fragile clothing to avoid damage.
• Do not pour bleach to directly onto laundry.
• Refer to the manual for the usage and quantity of the bleach. * Note: Always dissolve powdered
bleach before use.
For the quantity of concentrated washing powder, please refer to your manual.
REMARKS:
• Do not use excessive powdered detergent.
• Do not select high water level for small laundry loads.
MODE & INDICATOR LIGHTS
ON: indicate selected mode
FLASHING: indicate the program is running
• On startup, press 'Water evel' to select water level according to laundry load.
– 1-2 is low water level
– 3-5 is middle water level
– 6-8 is high water level
• When water level is set with '1,3,5 or 7', the light will always illuminate.
• When water level is set with '2,4, 6 or 8', the light will flash.
To add water during washing/rinse:
• Press 'Water evel' button to add water
• Release 'Water evel' button to stop.
• Pause operation & press 'Water evel' button to select higher water level.
• Press Start/Pause button to add water automatically and continue operation.
• If selected water level is lower than existing water level, the same water level will automatically apply
for the next cycle.
8 PROGRAM SELECTION:
'Normal', 'Standard', 'Heavy', 'Fast', 'Soak', 'Wash', 'Spin', 'Airdry'.
• When setting program 'soak, wash, spin or air dry', the light will always illuminate.
• When set program 'normal, standard, heavy or fast', the light will flash.
Note: Pro ram settin on startup will always revert to 'Normal'.
POWERS: the machine ON or OFF.
• Press START button to begin washing operation after setting water level, program and process.
• Press again to PAUSE washing.
DETERGENT G IDE CONTROL PANEL & FEAT RES
1312

1. Press POWER button to power on machine.
2. Machine will be in standby mode.
3. Select desired water level according to laundry load.
4. Press “program” button to select desired program.
5. To select "Air Dry" at the beginning of operation, press "Program" button to select "Air dry".
The machine will be in standby mode when air dry function is completed.
6. Close the top lid, press START/PAUSE to begin operation.
7. The buzzer will sound & power will automatically cut-off after operation is completed.
OPERATING INSTR CTIONS CARE & CLEANING
1514
AFTER EVERY WASH
• The machine stops automatically, and the buzzer will sound to remind you to remove the laundry or
begin another wash.
• Always unplug machine from the power supply after every wash and turn off the water tap to prevent
leaks.
EXTERIOR CARE & CLEANING
• Clean the machine exterior using a soft, damp cloth.
• Do not use abrasive cleansers or chemicals to avoid damaging plastic parts
and surface.
CLEANING INLET GATE
The inlet gate filter may be obstructed by dust. To clean:
• Turn off water tap and turn on the power switch.
• Start machine for 5 seconds & allow water in the inlet hose flow into the tub.
• Turn off power.
• Detach inlet hose, remove and clean the inlet gate valve and the inlet gate filter.
• Reassemble the inlet gate & filter.
CLEAN LINT FILTER
It is recommended to clean the lint filter after
every wash. To clean:
• Detach the lint filter (see Illustration 1).
• Open the lint filter and wash it (see Illustration 2).
• Close the lint filter and reassemble.
MAINTENANCE TIPS
It is advisable to turn off the water tap after every wash & detach the inlet hose, if
necessary. After every wash:
• Drain any remaining water in the tub immediately.
• Unplug power cord from the power supply.
• Store power cord and drain hose.
• Wipe the water on machine exterior & surface with soft cloth.
• Keep top lid open for a while to help prevent mould and stagnant smells from forming inside the
appliance.
The baffleplate
(
Press it and pull out the lint filterB
The baffleplate
(the black rubber block)
Illustration 1 Illustration 2
Close
Open
Close
Open

TRO BLESHOOTING OTHER F NCTION
1716
1. WHEN ALARM GOES OFF
• Use this troubleshooting guide for a list of possible solutions if the machine does not perform as
expected or malfunctions.
• If a solution cannot be found or the problem persists, please contact your authorized service center.
• Do not, under any circumstance, dismantle or attempt to repair the machine yourself.
ROBLEM OSSIBLE CAUSES SOLUTION
No d splay on control panel • Power Plug s not nserted correctly. • Re nsert power plug correctly.
• No power supply. • Inspect the power socket or change to
another power socket.
• Power sw tch s not turned on. • Press power sw tch.
• Check power supply
Water nlet hose leak ng • Inlet hose connector (connect ng w th the • Re nstall the nlet hose aga n.
tap) s not secure.
• Inlet hose and wash ng mach ne connector • T ghten the connector of the mach ne.
s loose.
Mach ne does not dra n • Dra n hose s not placed down on floor • Lay down the dra n hose to floor level.
level.
• Dra n hose s bent/tw sted or obstructed. • Stra ghten or clean the dra n hose.
No water supply • Tap s not turned on. • Restart when water supply s resumed.
• Water nlet hose s obstructed. • Turn on the tap.
• Follow nstruct ons “clean ng the water
nlet f lter”.
Sp n funct on stops and water • Excess ve or nsuff c ent laundry load.
supply resumes dur ng sp n • The mach ne w ll adjust tself
program • Mach ne s not placed on stable surface. automat cally.
Sp n funct on not work ng even • Top l d s open when dra n funct on beg ns • Close the top l d.
when sp n button s selected or when s completed.
Interm ttent sp n dur ng sp n • Balance laundry load for best sp n results. • Th s s normal.
funct on
Water flows from dra n hose • Water remnant n the tub dur ng factory • Th s s normal.
dur ng f rst use qual ty check and test
ROBLEM OSSIBLE CAUSES SOLUTION
Ind cator water level l ght, wash, sp n Water dra nage not completed even Open & close top l d to clear the alarm.
& other l ghts not on. after 5 m nutes.
Ind cator water level l ght, sp n, Top l d opened dur ng sp n funct on. Close top l d to clear the alarm.
& other l ghts not on.
Ind cator water level l ght, sp n, A r Sp n funct on s not balanced. Close top l d to clear the alarm.
Dry & other l ghts not on
Ind cator water level l ght, wash & Water nflow does not reach des red Open & close top l d to clear the alarm.
other l ghts not on level even after 5 m nutes.
Ind cator water level l ght, soak & Water exceeds the overflow level. Dra n excess water unt l the water level
other l ghts not on. reaches the deal water level.
Water level nd cator l ght & other Water level sensor malfunct on. Turn off the power supply and contact
l ghts not on. your author zed techn c ans.
2. IMBALANCE ADJ STMENT
• During spinning, violent vibrations may happen if laundry is not placed equally in the tub. This machine
has an automatic imbalance adjustment function. Once vibration exceeds beyond a specified level,
the adjustment system will start automatically to adjust the imbalance.
3. POWER S PPLY IS C T OFF A TOMATICALLY
• If START/PAUSE button is not pressed within 10 minutes after pressing the POWER button, power
supply will cut off automatically.
• Power supply will cut off automatically after washing is completed.

SPECIFICATIONS
1918
Model MWM-7 Zircon
Rated Voltage / Frequency 220-240V~ 50Hz
Washing ower 325W
Spinning ower 250W
Capacity 7.0kg
Weight Approx. 30kg
Dimension (mm) 520W x 530D x 878H