Morphy Richards Total Control User manual

download the
free app
FP402054 MUK Rev 4
Hand Blender Workcentre
* Register online for your 2 year guarantee. See the back of this instruction book for details (UK and Ireland customers only).
** Applies to serrator blade only. See back of this instruction book for details.
*** Independently tested by CATRA using the International Standard Cutting Test System to ISO 8442.5 vs a standard plain
edge blade.
www.facebook.com/morphyrichardsuk
@loveyourmorphy
www.morphyrichards.co.uk/blog
For competitions, product hints and tips
and more join us at
Please read and keep these instructions for future use
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 1

2
Health And Safety
In addition, we offer the following safety advice.
Location
•Do not use outdoors or in a bathroom.
•Always locate your appliance away from the edge of the
worktop.
•Do not place the bowl used with the appliance on a
highly polished wooden surface as damage may occur to
the surface.
ains cable
•Do not let the mains cable hang over the edge of the
worktop where a child could reach it.
•Do not let the lead run across an open space e.g.
between a low socket and a table.
•Do not let the cable run across a cooker or other hot area
which might damage the cable.
•The mains cable should reach from the socket to the
base unit without straining the connections.
Personal safety
•Care shall be taken when handling the sharp cutting
blades, emptying the bowl and during cleaning.
Other safety considerations
•Do not use the appliance for anything other than its
intended purpose.
Product specific safety
• WARNING: The blender blades and work centre blades
are very sharp. Handle with care when using and
cleaning.
• Do not clean the attachments under running water while
they are in position.
•IMPORTANT: Allow hot liquids to cool before adding to
the blender, always ensure the lid is fitted correctly.
•Be careful whilst hot liquid is blending or poured into the
blender as it can be ejected due to sudden steaming.
•Switch off the appliance and disconnect from supply
before changing accessories or approaching parts that
move in use.
Electrical requirements
Check that the voltage on the rating plate of your
appliance corresponds with your house electricity supply
which must be A.C. (Alternating Current).
Should the fuse in the mains plug require changing, a 3
amp BS1362 fuse must be fitted.
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
•This appliance can be used by persons with reduced physical,
sensory or mental capabilites, or lack of experience and
knowledge, if they have been given supervision or instruction
concerning the use of the appliance in a safe way and understand
the hazards involved.
•Children shall not play with the appliance.
•This appliance shall not be used by children.
•Keep the appliance and cord out of reach of children.
•Do not blend for longer than the time periods recommended in
‘Usage’ on page 9.
•Always disconnect from the supply if left unattended and before
assembling, dissembling or cleaning. For care and cleaning refer
to page 10.
•Avoid touching moving parts. Keep hands, hair and clothing, and
utensils away from the attachment blades during operation, to
prevent personal injury and/or damage to the appliance.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 2

3
Health And Safety ........................................................ 2
Introduction .................................................................. 3
Total Control ................................................................. 4
Product Overview ........................................................ 5
Before First Use ........................................................... 6
Using Your Hand Blender ............................................ 6
Using Your Workcentre Blade ..................................... 7
Using Your Grating/Slicing Discs ................................ 8
Suitable Foods ............................................................. 9
Note .............................................................................. 9
Turbo Button ................................................................ 9
Usage ........................................................................... 9
Blending In A Saucepan .............................................. 9
Attachments ................................................................. 10
Hints And Tips .............................................................. 10
Care And Cleaning ....................................................... 10
Contact Us ................................................................... 10
Recipes ......................................................................... 11
Guarantee ..................................................................... 20
Contents
Thank you for your recent purchase of this Morphy Richards Total
Control Workcentre.
Your Hand Blender Workcentre comes with a number of attachments
and a locking connection for safety. Please read the instructions for
information on how to use each attachment thoroughly before use.
Remember to visit www.morphyrichards.co.uk to register your
product’s two year guarantee.
Introduction
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 3

4
Giving you the power to create with
confidence.
Introducing the Total Control Hand Blender – the
simple way to bring confidence to your cooking.
The Total Control Hand Blender allows you to
create delicious smoothies and shakes, blend
soups and sauces with the confidence and
reassurance the Smart Response Technology
delivers.
Smart Response Technology allows you to have
Total Control of the blending process with the
simple squeeze of a button. The Smart Response
Technology gently feeds power into the blender
as you need it, there are no sudden jerks or
splatters, giving you complete confidence in the
kitchen.
Choose the speed that best suits the job at hand
using the simple twist motion Speed Control,
there are 8 to choose from. Even when using a
higher speed you can feel assured that the Smart
Response Technology feeds power in gradually
building to your chosen speed for the job at hand.
When you have blended to your desired
consistency simply release the button and the
Total Control Hand Blender will steadily slow
down and stop, ensuring no splash and no
suction.
Total Control Hand Blender, giving you the power
to create with confidence.
Variable Speed Control
Ergonomic Soft Grip Handle
650 Watt Motor
Precision Control Trigger
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 4

5
Features
(1) Speed Control
(2) Precise Control Trigger
(3) Turbo Button
(4) Main Unit
(5) Blending Leg
(6) Serrator Blade
(7) Beaker Lid
(8) Beaker
(9) Feed Tube
(10) Small Pusher
(11) Pusher
(12) Lid Release Handles (x2)
(13) Lid
(14) Bowl
(15) Workcentre Blade
(16) Spindle
(17) Grating/Slicing Disc
Coarse
(18) Grating/Slicing Disc Fine
(19) Attachment Release
Button
(20) Heel Rest
16
1
2
3
19
20
1312
9
10 11
14
15
1
5
6
3
4
7
8
2
17
18
Product Overview
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 5

6
•WARNING: Carefully unpack your Total Control
Hand Blender Workcentre as the blades are
very sharp.
•Wash all parts except the Main Unit (4) and
Lid (13) in hot soapy water before use. Dry all
parts thoroughly before use.
•Do not fully submerge the Blending Leg in water.
Wash only the Serrator Blade head (6).
•Wipe the Lid with a hot damp cloth to clean. Do
not immerse in water.
•Do not immerse the Main Unit in water.
Before First Use
4
Press the Precise Control Trigger to begin
blending. The speed will increase the harder
you press the button.
3
Place the Blending Leg into the food to be
blended. We recommend using the Beaker (8)
for the best results.
2
Select the speed on the Speed Control(1).
The Hand Blender will not start unless the
Precise Control
Trigger (2) or
Turbo Button (3)
is pressed.
1
Attach the Main Unit (4)to the Blending Leg
(5)and push to lock into place.
Using Your Hand Blender
5
Release the Precise Control Trigger to stop.
Allow the blades to stop BEFORE removing
the Hand Blender from the food.
6
Unplug the Main Unit from the mains. Press the
Attachment Release Button (19). and remove the
Blending Leg from the Main Unit for cleaning.
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 6

7
4
Push the Main Unit (4) onto the Lid. The Main
Unit will not lock into place for safety reasons.
3
Align the tabs on the Lid (13) with the slots on
the Bowl. Place the Lid and Pusher (11) onto
the Bowl. Push down to lock.
2
Place the food into the Bowl. Do not exceed
the maximum level.
1
Place the Workcentre Blade (15) on the shaft in
the Bowl (14).
WARNING: Blades are sharp.
5
Select speed 6 or 7 on the Speed Control (1)
and press and hold the Precise Control Trigger
(2) to start. Do not open the Lid while in use.
6
When finished, Release the Precise Control
Trigger and lift the Main Unit from the Lid.
8
CAREFULLY remove the Workcentre Blade
before emptying the Processor Bowl.
7
Pull the Lid Release Handles (12) to unlock
and remove the Lid.
Using Your Workcentre Blade
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 7

8
3
Push the Main Unit (4) onto the Lid. The Main
Unit will not lock into place for safety reasons.
2
Place the Spindle (16), onto the shaft in the
Processor Bowl. Place the selected Disc on the
Spindle and press down until the disc locks into
place, you will hear a click. Fit the Lid (13) onto
the Bowl (14). Press down to lock into place.
1
Select the Grating/Slicing Disc (17),(18), you
require. The Coarse and Fine discs are
reversible (one side slices, the other grates).
WARNING: DISCS ARE SHARP
6
Press down with the Pusher (11), pressing the
food into the disc. Release the Precise Control
Trigger when finished.
8
Remove the Grating/Slicing Disc and
Spindle before emptying the Processor Bowl.
7
When finished, lift the Main Unit from the Lid.
Pull the Lid Release Handles (12) to unlock
and remove the Lid.
Using Your Grating/Slicing Discs
5
4
Place the food into the Feed Tube (9).
Select speed 6 on the Speed Control (1) and
press and hold the Precise Control Trigger (2)
to start. Do not open the Lid while in use.
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 8

9
•When using your Total Control Workcentre Blade
(15) or Grating/Slicing Discs (17), (18) do not use
a slower speed than indicated above. Damage
could occur to the motor.
•Your Total Control Hand Blender is fitted with a
Turbo Button (3). Press the Turbo Button to run
the Hand Blender on a faster speed for
intermittent bursts.
•WARNING: Your Hand Blender is designed for
intermittent use. Do not use continuously for
more than 90 seconds. Allow to cool down for a
minimum of 5 minutes before further use.
•Do not use a non-stick pan as the Blending Leg
could damage the non-stick coating.
1. Remove the saucepan from the heat.
2. To avoid excessive splashing, place the Blending
Leg (5) into the food before switching the Hand
Blender on.
3. Hold the pan steady with your other hand and
lightly press the Precise Control Trigger (2). Start
slowly, and increase the speed as needed using
the Control Trigger.
4. Move the Serrator Blade (6) through the food
using an up and down motion.
5. Allow the Blades to stop moving before removing
from the pan.
•WARNING: Lifting the Serrator Blade out of the
food while running, or using a high speed
setting in a small pan could splash hot liquid.
Extra care should be taken when using the
Hand Blender in this manner.
Note
Turbo Button
Usage
Blending In A Saucepan
• The speeds and times listed below should be used as a guide.
Suitable Foods
•Grating/Slicing
Disc
•Cheese •400g •6•10-30 seconds
•Grating/Slicing
Disc
•Fruit •800g •6•10-30 seconds
•Grating/Slicing
Disc
•Vegetables •400g •6•10-30 seconds
•Grating/Slicing
Disc
•Chocolate •400g •6•10-30 seconds
•Workcentre
Blade
•Vegetables •500g •7•20-40 seconds
•Workcentre
Blade
•Breadcrumbs •300g •7•45-60 seconds
•Workcentre
Blade
•Crumble Topping •500g •7•45-60 seconds
•Workcentre
Blade
•Butter cream •300g •7•50-60 seconds
•Workcentre
Blade
•Raw Beef •400g •7•30-60 seconds
•Workcentre
Blade
•Blending •500g •7•30-40 seconds
Attachment Food ax Quantity Speed Time
•Blending Leg •Soup or Sauce -•4•40-60 seconds
•Blending Leg* •Milkshake •450ml •4-5 •20-30 seconds
•Blending Leg* •Ice •3 cubes •8•5-15 seconds
•Blending Leg* •Carrots
with water
•200g
•300ml
•6•40-60 seconds
*When using the Beaker supplied
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 9

10
Blending Leg (5)
•The Blending Leg is designed for pureeing foods
such as soups, sauces, milkshakes, smoothies,
baby food or crushing ice.
•The Blending Leg is not suitable for grinding
hard items such as coffee beans.
Workcentre
•The Workcentre Blade (15) is suitable for
chopping nuts, vegetables, herbs, pâté, meat,
dried bread and combining foods.
•Do not use the Workcentre to mix cake batters or
bread dough. The blade is not suitable for
kneading heavy mixtures.
•The Workcentre Blade is not suitable for grinding
hard objects such as coffee beans or ice.
•Do not use the Workcentre to crush ice.
•When blending foods with strong colour (eg.
carrots), the plastic parts of the appliance may
become discoloured. Wipe with cooking oil to
clean any discoloured parts. Wash thoroughly in
hot soapy water before re-using.
•When blending using the Blending Leg (5), start
the process by inserting the Blending Leg into the
ingredients. This will ensure all the ingredients are
pulled into the blade to be processed. Gently
rotate the Blending Leg, lifting it up and down in
the ingredients. Continue this movement until the
mixture is of the desired consistency. Do not
remove from the liquid while the blades are in
motion.
•Do not lift the Blending Leg out of the mixture
completely when running, as splashing may
occur.
•While using the Workcentre Bowl (12) you may
need to scrape the sides of the bowl down using
a silicone spatula partway through blending.
•WARNING: Always unplug the appliance from the
mains socket before cleaning and maintenance.
•WARNING: Handle the blades with care as they
are sharp.
•Wash all parts except the Main Unit (4) and Lid
(13) in hot soapy water, dry immediately.
•Clean the Main Unit with a damp cloth and dry all
the parts thoroughly.
•WARNING: Never immerse the Main Unit in water
or any other liquid.
•Do not fully submerge the Blender Leg in water,
wash only the Serrator Blade head.
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from.
Please have the product name, model number
and serial number to hand when you call to help
us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk To Us
If you have any questions or comments, or want
some great tips or recipe ideas to help you get
the most out of your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Contact Us
Care & Cleaning
Hints & Tips
Attachments
402054 REV4.qxp_Layout 1 05/06/2015 13:50 Page 10