Morphy Richards 28009 User manual

Illustration
Location of controls
1 Function selector switch
2 PMindicator
3 Alarm indicator
4 Dial scale and pointer
5 Tuningcontrol
6 Band selector switch AM/FM
7 Buzzer/Volumecontrol
8 Minutebutton
9 Hour button
10 FM wire aerial
11 Time button
12 Sleepbutton
13 Alarm button
14 Snoozebutton
15 Battery compartment
(located underneath unit)
Switching on and setting the clock time
Before any alarm functions can be used, you must set the clock to the correct time.
1 Place the unit on a flat surface. Plug the mains plug into the wall socket
and switch on the wall socket
2 The LED clock display will flash.
3 Press and hold the TIME button (11) and simultaneously hold down the
HOUR button (9) or the MINUTE button (8). The LED clock display will
fast forward the minutes and hour segments. Release the TIME button (11)
when your desired time is set.
4 The PM indicator (2) will illuminate to indicate 12.00 midday has been
reached.
Radio operation
FM wire aerial
To obtain the maximum FM reception fully extend the wire FM aerial (10) (which
is located at the rear of the unit) and alter the direction of the wire for best
results.
The aerial for the AM waveband is located inside the unit. To obtain the maximum
AM reception rotate the clock radio.
1 Slide the FUNCTION SELECTOR switch (1) to the ‘ON’ position.
2 Adjust the VOLUME control (7) to a suitable level.
3 Set the BAND SELECTOR switch (6) to either AM or FM as
desired.
4 Slowly adjust the TUNING control (5) to select your desired station.
5 To switch off the radio, slide the FUNCTION SELECTOR
switch (1) to the ‘OFF’ position.
2 Band Alarm
Clock Radio
28009 / 28022 OPERATINGINSTRUCTIONS
Electrical requirements
Check that the voltage on the rating plate of your clock radio corresponds
with your house electricity supply which must be A.C. (Alternating current).
For clock radios with fitted plug.
If the socket outlets in your home are not suitable for the plug supplied
with this appliance the plug should be removed and the appropriate one
fitted.
IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST
BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS
HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET.
Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362
fuse must be fitted.
The socket outlet should be installed near the equipment and shall be easily
accessible.
P.2
P.3 P.4
1
○○○
2
3
4
8
13 12 11 10
6
7
9
5
14
○○○○○○
15
Battery back-up facility (unit will work without a battery being fitted)
Your alarm clock radio is equipped with a battery back-up facility.
1 Remove the battery compartment cover (located underneath the unit) by
pushing in the clip and lifting off.
2 Insert a battery size 9 volts PP3/6LR61 and connect to terminals (Ensure
batteries are inserted correctly)
3 Replace the battery compartment cover.
Should a power interruption occur the clock will continue to run, however, time
keeping will not be accurate. The display will be extinguished to conserve battery
life but the memory will retain details of the clock time and alarm settings.
If the optional battery is not installed in case of the AC power failure the display
will blink to indicate the power was interrupted. You will need to reset the clock
and alarm.
Battery back-up is designed to operate for a short period only.
If the unit is not to be used for a prolonged period, remove the battery to
avoid battery leakage.
In the interests of environmental safety : dispose of batteries safely.

To stop the alarm tone
The alarm is programmed to run for 1 hour 59 minutes.
1 To stop the alarm, press the ALARM button (13). The alarm will stop and
will operate again 24 hours later.
2 To stop the alarm temporarily, press the SNOOZE button (14). The alarm
will sound again 9 minutes later.
3 To switch the alarm setting off permanently, slide the FUNCTION
SELECTOR switch (1) to the ‘Off’ position.
Snooze function
The alarm can be interrupted for a 9 minute period.
1 Press the SNOOZE button (14), after 9 minutes the radio or alarm
buzzerwillsoundagain.
To set the sleep function
Your clock radio is equipped with a sleep function that will turn the radio
on and switch it off automatically after a set period of time from between
59 minutes to 1 minute. Pressing the hour button (9) will extend the sleep time to
1 hour 59 minutes.
1 Press the SLEEP button (12) the LED display will show 0:59
sleep time at the same time the radio will come on and stay on for
59 minutes.
2 Press and hold the SLEEP button (12) whilst pressing the MINUTE
button (8) or HOUR button (9) or press and hold the sleep button (12),
the sleep time shown on the LED display will start descending.
3 Release all buttons when the desired sleep time is shown on the LED
display.
4 After the set sleep time has elapsed, the radio will automatically switch
off.
5 To switch off before the set sleep time has elapsed press the SNOOZE
button (14).
Maintenance
Do not expose your clock radio to extremes of temperature. The product should
be kept in a warm environment free from dust and damp. For external cleaning
use only a soft, clean, damp cloth. Use of detergents may damage the finish.
Technical specification
AC Power supply : 230v AC 50Hz
Battery back-up : 9V DC type 6LR61/PP3 (not provided)
Radio : FM88Mhz- 108Mhz
: AM540Khz-1600Khz
Warning labels
WARNING: to reduce the risk of electric shock, do not expose this
appliance to rain or moisture.
ATTENTION: To reduce the risk of electric shock, do
not remove the cover. There are no user
serviceable parts inside the unit. Refer any
servicing to qualified personnel.
The lightning flash with arrowhead symbol within the triangle is a
warning sign alerting the user of ‘dangerous voltage’ inside the
unit.
The exclamation point within the triangle is a warning sign alerting
the user of important instructions accompanying the product.
To prevent fire or shock hazard do not expose this apparatus to
dripping and splashing.
Guarantee
Morphy Richards products are manufactured to internationally accepted quality
standards. In addition to your statutory rights, Morphy Richards guarantee your
product to be free from manufacturing and component defects for a period of TWO
YEARS from date of purchase.
If your product proves to be defective within 28 days of purchase, your Morphy
Richards dealer from whom the product was purchased will be pleased to replace it
free of charge.
Should your product develop a defect within the guarantee period but after the
replacementperiod,pleasereturn the product to the following address, together with
the proof of purchase, brief details of the symptoms and your own name and
address.
Morphy Richards Limited
Talbot Road
Mexborough
South Yorkshire
S64 8AJ
Your post office will provide a certificate of posting. The product will be repaired
and returned to you promptly.
If you need any further advice, please call our Helpline (UK local rate)
on: 08450 777700 (Mon-Fri)
Morphy Richards Website: www.morphyrichards.co.uk
446/8001/73 Rev5
Importedby:MorphyRichardsLtd, TalbotRoad,Mexborough,S648AJ
Setting the alarm time
1 Press and hold the ALARM button (13) and simultaneously press the HOUR
(9) or MINUTE button (8) to set the display to the desired alarm time.
Release the ALARM button (13) when the desired alarm time is set.
Wake up to the radio alarm
1 Switch the FUNCTION SELECTOR switch (1) to the ‘ON’ position.
2 Set the BAND SELECTOR switch (6) to select either FM or AM
wavebands as desired.
3 Adjust the VOLUME control (7) to a suitable level.
4 Slowly adjust the TUNING control (5) to the desired station.
5 To check that the alarm time has been set, slide the FUNCTION
SELECTOR switch (1) to the ‘AUTO’ position. The ALARM ON indicator
(3) will light. The radio station will wake you up at the set alarm time.
The alarm will automatically turn off after 1 hour 59 minutes.
Ensure the station you select will be transmitting at the preset alarm time.
Wake up to the alarm buzzer
In order to check the correct alarm time has been set press the ALARM button
(13). The display will indicate the alarm time set.
1 Turn the BUZZER/VOLUME control (7) to the ‘Buzzer’ position until you hear a
click.
2 Slide the function selector switch (1) to the ‘AUTO’ position. The ALARM ON
indicator (3) will light.
The buzzer alarm will activate at the set alarm time.
The buzzer will automatically turn off after 1 hour 59 minutes.
P.5 P.6
P.7