Morphy Richards Jet Steam 333024 User manual

Steam Generator
RN333024 UK Rev1
Please read and keep these instructions for future use
* Register at www.morphyrichards.co.uk/support
UK and Ireland customers only
IF YOU HAVE ANY DIFFICULTY WITH THIS PRODUCT,
INSTEAD OF TAKING IT BACK TO THE RETAILER, TRY:
1. The instruction booklet 2. Refer to www.morphyrichards.com
3. Or call our helpline: UK: 0344 871 0944, EIRE: 1800 409 119 (For UK & Eire customers only)
Register your guarantee online: www.morphyrichards.co.uk/support
We'll keep you updated with special offers, competitions and important product information.
Purchase spare anti-scale cartridges to keep your product performing like
new for longer. Available by calling our Spares Helpline on 0344 873 0710.
IMPORTANT: To reduce limescale damage we recommend using deionised,
distilled or demineralised water, available at most large supermarkets. This
is particularly important if you live in a hard water area.
Never use battery topping up fluid or water containing any substances like
starch, sugar, fragrant additives or defrosted water from a refrigerator.
Remember to clean your steam generator and change the antiscale cartridge.
Failure to adhere to the above guidelines will invalidate your guarantee.
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 1

2
The use of any electrical appliance requires the following common sense safety rules.
Please read these instructions carefully before using the product.
Important safety instructions
•WARNING: Disconnect from the mains supply
before carrying out any routine maintenance.
•WARNING: Misuse of the appliance could cause
personal injury.
•This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities, or lack of experience
or knowledge, if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
•Keep the steam generator and its cord out of reach
of children less than 8 years of age at all times.
•The steam generator must not be left unattended
while it is connected to the supply mains.
•The steam generator must be used and rested on
a stable surface.
•When placing the iron on the steam generator
base, ensure that the surface on which the base is
placed is stable.
•The steam generator is not to be used if it has been
dropped, if there are visible signs of damage or it
is leaking.
•The filling aperture may be opened during use, due
to the design of the system.
•Do not operate with a damaged steam/supply
cord or grommet, it must be replaced by the
manufacturer, its service agent or similarly qualified
person in order to avoid a hazard.
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 2

3
Health and safety ............................................................................
Electrical requirements ..................................................................
Steam generator overview / Features ...........................................
Temperature guide ..........................................................................
Location ...........................................................................................
Before use ........................................................................................
Using the Steam Generator ...........................................................
Features ...........................................................................................
Maintenance ....................................................................................
Emptying and storing .....................................................................
Guarantee ........................................................................................
Contact us .......................................................................................
Contents
2
3
4
4
5
5
5 & 6
7
7
7
8
8
Personal safety
•CAUTION - HOT:
Burns can occur from
touching hot parts, hot
water or steam, or the
iron rest plate.
• WARNING: Never direct steam at
electrical components or fittings.
If in doubt about the suitability of
steam for cleaning an appliance,
contact the appliance
manufacturer for advice prior to
cleaning.
• WARNING: Never touch the plug
or cable with wet hands.
• WARNING: Nozzles and tools will
be hot after use. Allow to cool
before attempting to remove.
• WARNING: Do not
discharge the
steam towards
people or
animals.
Danger of
scalding.
•To protect against fire, electric
shock and personal injury, do not
immerse cord, plug or steam
generator in water or other liquid.
•The plug should be removed from
the wall socket after use, before
cleaning, filling or changing the
accessories, or carrying out user
maintenance.
Location
•Do not use or keep this product
outside.
•Do not store the appliance near hot
surfaces eg. ovens or heating
appliances.
Mains cable
•WARNING: A damaged or severed
mains cable fitted with a plug
should never be connected to the
mains supply. It must be
destroyed, as a damaged cable
becomes hazardous if connected
to a power socket.
•Do not let the mains lead come into
contact with the hot soleplate of the
iron.
•Do not allow the mains lead to
become strained.
Product safety
•WARNING: Always test on an
inconspicuous area first. Never
use on materials that can not
resist high temperature, such as
dralon, natural fur etc.
•Never modify the appliance in any
way.
Other safety considerations
•Do not use any chemical
detergents, perfumes, alcohol or
descaler etc in water.
•Repairs to electrical appliances are
only to be undertaken by trained
personnel.
•Unprofessional repairs can be
dangerous for users.
•Use only genuine orphy Richards
spare parts and accessories.
•The appliance must not be left
unattended while connected to the
supply mains.
•This appliance is intended for
domestic use only. isuse or use
for commercial or any other
purpose will render the guarantee
invalid.
Electrical requirements
•Check that the voltage on the rating
plate of your appliance corresponds
with your house electricity supply
which must be A.C. (Alternating
Current).
•If the socket outlets in your home
are not suitable for the plug
supplied with this appliance, the
plug should be removed by trained
authorised personnel and the
appropriate one fitted.
• WARNING: This appliance must
be earthed.
•Should the fuse in the mains plug
require changing, replace it with a
fuse of the same rating as originally
fitted.
STEAM
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 3

4
(1) Water tank
(2) Anti-scale filter
(3) Steam trigger
(4) Temperature control dial
(5) Iron
(6) Soleplate
(7) Iron rest plate
(8) Base Unit
(9) Temperature indicator light
(10) Steam supply cord
(11) Iron heel rests
(12) Boiler ready indicator light
(13) Power switch with indicator light
Steam generator overview
Heat setting markings on the temperature dial of all orphy Richards irons match those of the International
Textile Care Labelling Code
Temperature guide
Symbol (120°C ax) Cool (160°C ax) Warm (210°C ax) Hot
Control dial positions Do not iron • •• •••
Fabric Nylon, Acetates,
synthetic fabrics
Wool, Polyester
mixtures
Cotton, Linen Rayon,
Rayon mixtures
Ironing Iron on wrong side, if
moisture required, use
damp cloth
(not Acetate)
Fabrics requiring
this setting usually
require steam
pressing.
Steaming
3
4
9 11
1 2
5
8
7
6
12
13
10
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 4

5
Using the Steam Generator
Plug the appliance into a mains outlet and press
the power switch with indicator light (13). The
switch will illuminate.
The boiler ready indicator light (12) situated
above the power switch will also illuminate,
indicating the boiler is on its heating cycle and
will go out when the required temperature is
reached.
Remove the detachable water tank (2). Lift the
anti-scale cartridge (3) out of the water tank and fill
the tank with water through the space where the
cartridge was. Fill to the max fill line . Reposition
the anti-scale cartridge and the water tank.
IN HARD WATER AREAS, WE RECOMMEND
USING DEIONISED, DISTILLED OR
DEMINERALISED WATER.
Never use battery topping up fluid or water
containing any substances like starch, sugar,
fragrant additives or defrosted water from a
refrigerator.
NOTE: Please see point 2 of ‘Exclusions’ on page 8.
Re-filling during use
When the water level becomes low, the pump
begins to emit a clicking noise. This is due to air
being pumped instead of water and is quite normal.
Refilling can be done whilst the appliance is in
operation. It is not necessary to wait for the
appliance to cool down. Slide out the water tank
and fill (see filling instructions).
Locate the steam generator horizontally on the iron
rest plate of your ironing board (if large enough) or
on a heat resistant stand at the same height as
your ironing board or below it. Always ensure the
steam generator is on a firm surface when ironing.
WARNING: Do not use the product on a surface
which could be damaged by heat or steam such
as a polished wood surface.
Remove any protective sticker from the soleplate
and the base unit, if any.
Unwind and straighten the power cord and supply
cord.
Textiles and clothes are supposed to carry ironing
instructions. If they don’t, you should follow the
Temperature guide on page 3, but be sure to test
the temperature by ironing the hem of the garment
or similar discreet area first.
We recommend for first time ironing that you
iron over an old towel.
LocationBefore use
1) Filling the water tank 2) Switching on
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 5

6
Turn the temperature dial (4) to suit the garment
(see ‘Temperature guide’ on page 4). The
appliance is ready to use when the iron
temperature indicator light (9) switches off.
It is advised to begin with ‘cool’ fabrics (see
above) and work up to higher settings. An iron
heats up quicker than it cools down so you’ll save
time and electricity.
If you turn the temperature dial (4) down from a
hot setting to a cooler setting, wait until the
temperature indicator light (9) goes out (indicating
the correct temperature has been reached) before
you continue ironing.
Using the Steam Generator (continued)
3
Press and hold the steam trigger (3) to release
steam. There will be a slight delay whilst the
steam is drawn from the base and along the
steam cord to the irons soleplate (6).
NOTE: Residual steam - as the steam has a long
distance to travel along the steam cord it is likely
that there will still be some steam coming from the
soleplate for a short while after you have released
the trigger. This is normal and will eventually stop
after several seconds.
WARNING: The steam supply cord will get hot
during use.
To switch the iron off, turn the temperature
dial (4) on the iron (5) in an anti-clockwise
direction to ‘ in’.
Press the power switch (13) to switch to off.
The power indicator light will be
extinguished.
Disconnect the plug from the mains outlet.
3) Temperature Selection 4) Ironing with Steam
5) Switching off
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 6

7
Dry ironing
To use your steam generator as a dry iron only,
follow steps 2 and 3 of ‘Using the Steam
Generator’ on pages 5 and 6. You do not need to
put water in the tank or select a steam level.
Steam function
During steaming, small amounts of water may be
ejected from the soleplate (6) . This is normal and
can be avoided by
only using the iron when it is
at the correct temperature (the temperature
indicator light (9) on the iron (5) goes out when
ready).
Sudden jolts of the boiler unit can also cause
water droplets on the soleplate; therefore, do not
move the base unit during ironing.
Vertical steam
Vertical steam is useful for removing creases
from hanging clothes, curtains, upholstery, etc.
Hold the iron
(5) between 1cm and 2cm away
from the item and press and hold the steam
trigger
(3) for vertical steam.
WARNING: Do not use the vertical steam
feature on clothes that are being worn.
Features
3
To clean a coated soleplate
Do not use scouring powder or solution as this
could cause damage to the coating.
If any man-made fibres fuse to the soleplate (6), set
the iron at the AX position and pass it over a clean
piece of cotton to draw the deposit off the surface.
To clean the exterior
Allow the unit to cool and wipe over with a damp
cloth and mild detergent, then wipe dry.
Replacing the anti-scale filter
The anti-scale filter is designed to reduce the
build-up of limescale which occurs during steam
ironing. This will prolong the working life of your
iron. However, please note that the anti-scale filter
will not completely stop the natural process of
limescale build-up.
How often you need to replace the anti-scale filter
depends on how often you use your iron with its
steam functions and how hard’ your water supply
is. Water hardness varies greatly from one area to
another. For advice on the relative hardness of your
water, contact your local water supplier.
If you iron more or less frequently, then you should
alter the interval between refills accordingly.
To obtain replacement anti-scale refills, telephone
our spares number on: 0344 873 0710.
If a new re-fill is not available, you may continue
operating the appliance but scale will build up in
the system. Replace the anti-scale refill as soon
as possible.
1Disconnect the appliance from the mains outlet.
2Slide out the tank and remove the anti-scale filter.
3Pull the plate from the end of the filter A.
4Remove the foam pad Band slide out the spent
anti-scale sleeve C.
5Place the refill into the filter, reposition the foam
pad and clip the plate onto the filter, making sure
it locks in position.
6Connect the appliance to the mains supply and
switch on.
7Replace the water tank (1). The unit is now ready
to use or store.
Allow the appliance to cool.
Remove the detachable water tank (1) and empty
it. Once the water tank is empty, re-attach it to
the base unit (8).
WARNING: Do not pull too tightly on the steam
supply cord or on the cable support when looping
the power cord and steam supply cord. Damage to
cables caused by wrapping too tightly will not be
covered by the
guarantee.
Maintenance
Emptying and storing
ABC
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 7

RN333024 UK Rev1 04/20
Your standard 1 year guarantee is extended for an
additional 12 months when you register the product within
28 days of purchase with orphy Richards. If you do not
register the product with orphy Richards within 28 days,
your product is guaranteed for 1 year. To validate your 2
year guarantee register with us online at
www.morphyrichards.co.uk/support
Or call our customer registration line
UK0344 871 0242
IRE 1800 409 119
N.B. Each qualifying product needs to be registered with
orphy Richards individually.
Please note that the 2 year guarantee is only available in
the UK and Ireland. Please refer to the 1 year guarantee
for more information.
It is important to retain the retailer’s receipt as proof of
purchase. Staple your receipt to this back cover for future
reference.
Please quote the following information if the product
develops a fault. These numbers can be found on the base
of the product.
odel no. Serial no.
All orphy Richards products are individually tested before
leaving the factory. In the unlikely event of any appliance
proving to be faulty within 28 days of purchase, it should
be returned to the place of purchase for it to be replaced.
If the fault develops after 28 days and within 12 months of
original purchase, you should contact the Helpline number
quoting odel number and Serial number on the product,
or write to orphy Richards at the address shown.
You may be asked to return a copy of proof of purchase.
Subject to the exclusions (see Exclusions), the faulty
appliance will then be repaired or replaced as appropriate
and dispatched usually within 7 working days of receipt.
If, for any reason, this item is replaced or repaired during
the 1 year guarantee period, the guarantee on the new
item will be calculated from original purchase date.
Therefore it is vital to retain your original till receipt or
invoice to indicate the date of initial purchase.
To qualify for the 1 year guarantee, the appliance must
have been used according to the instructions supplied.
For example, water should be emptied after each use.
orphy Richards shall not be liable to replace or repair the
goods under the terms of the guarantee where:
1The fault has been caused or is attributable to accidental
use, misuse, negligent use or used contrary to the
manufacturer’s recommendations or where the fault has
been caused by power surges or damage caused in
transit.
2The fault has been caused by using water other than that
recommended by orphy Richards.
3The fault is caused by limescale build-up.
4The cables are damaged due to wrapping too tightly or
excessive kinking.
5The appliance has been used on a voltage supply other
than that stamped on the products.
6Repairs have been attempted by persons other than our
service staff (or authorised dealer).
7The appliance has been used for hire purposes or non
domestic use.
8The appliance is second hand.
9orphy Richards reserves the right not to carry out any
type of servicing under the guarantee at its discretion.
•This guarantee does not confer any rights other than those
expressly set out above and does not cover any claims for
consequential loss or damage. This guarantee is offered
as an additional benefit and does not affect your statutory
rights as a consumer. orphy Richards products are
intended for household use only. See usage limitations
within the location safety instructions.
orphy Richards has a policy of continuous improvement
in product quality and design. The company, therefore
reserves the right to change the specification of
its models at any time.
For electrical products sold within the
European Community. At the end of the
electrical products useful life, it should not be
disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer for
recycling advice in your country.
Exclusions
Your 1 year guarantee
Disclaimer
Registering your guarantee
Helpline
If you are having a problem with your appliance,
please call our Helpline, as we are more likely to
be able to help than the store you purchased the
item from. Please have the product name, model
number and serial number to hand when you call
to help us deal with your enquiry quicker.
UK Helpline: 0344 871 0944
IRE Helpline: 1800 409 119
Spares: 0344 873 0710
Talk to us
If you have any questions or comments, or want
some great tips to help you get the most out of
your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: @loveyourmorphy
Website: www.morphyrichards.com
Address:
The After Sales Division
Morphy Richards Ltd
Mexborough,
South Yorkshire,
England, S64 8A
Contact us
RN333024 MUK Rev1.qxp_IB 21/04/2020 17:00 Page 8