MOTECK TXH5 User manual

CONNECT DOWN
M
E
M
O
R
Y
Connect RF Adapter to control box
Connect RF Adapter to control box (or Twinmat) by inserting the plug of
RF Adapter to the handset socket on the control box. the green LED on
the RF Adapter will light on for around 1 second to show that connection
is done.
Lock Mode
Press the red lock button on the rear side of the remote handset to lock
the buttons on the front side. The orange LED on the front side will flash
4 times to show that buttons are locked. To unlock, simply press the red
lock button one more time, 4 flashes of the green LED will follow to
show that it's now in unlock mode. Please press the lock button to
unlock, whenever the batteries are changed.
Pair with Remote Handset
Put the plug of RF Adapter into the handset socket of the control box (
the LED will be on for 1 second), press and hold "connect" button on the
RF Adapter until the LED flashes (around 2 minutes), release the
"connect" button on the RF Adapter and press any button on the
Remote handset to pair the remote handset and the RF Adapter.
*This step is necessary when remote handset is NOT controlling the RF Adapter or
a new remote handset is used.
Clear Remote Handset
Plug out RF Adapter, press and hold "connect" button, then plug RF Adapter in the
socket of the control box, while keep holding the "connect" button (around 5 seconds)
until the LED turns off.
Caution:
This device might be interfered by some other devices with same frequency (2.4 GHz;
eg. WIFI router or WIFI hub). If so, please move any port of the dip switch in the battery
room to change channel and pair the remote handset with the TX adapter one more
time.
Emergency Lowering
Press "down" button on the RF Adapter to lower down ALL the actuators
or motors.
Green LED
Orange LED
Lock Button
User Guide
TXH5 Handset Model: TXH5
MOTORIZE OUR WORLD
R

Buttons' Definition
5
Back Leg
Massage Intensity :
Back = Massage # 1
Leg = Massage # 2
Press once to start each group
(Default intensity is 1).
Press 2nd time to increase to 2.
Total 5 intensities. A buzzer will
beep at 5.
I
f Leg and/or Back is on, entering Wave
Mode #1 / #2 will start at current intensity
(not default 1).
5 (beep) 5 (beep)
0
Intensity
Press
(times)
5 10 15
Wave Mode #1 :
MSG #1 on, MSG #2 off; then
MSG #1 off, MSG #2 on (in cycles...).
Press once to start (Default period is 5
seconds).
Press 2nd time to 4 (faster).
time
MSG #1
MSG #2
ON
OFF
ON
OFF
5~1 seconds
Wave Mode #2 :
MSG #1 on, MSG #2 on; then
MSG #1 off, MSG #2 off (in cycles...).
Run Simultaneously.
Other is the same as Mode #1.
time
Group #1
Group #2
ON
OFF
ON
OFF
5~1 seconds
Total 5 frequencies. A buzzer will beep at 1
(fastest).
1 (beep)
0
Cycle
Period
Press
(times)
1 (beep)
5 10 15
5
Default period is not able to be changed by end-user.
5 (beep) 5 (beep)
M1 Extend
M1+M2 Extend M1+M2 Retract
M1 Retract
M2 RetractM2 Extend
Massage
OFF
Back
Leg
Press to stop all massage motors.
1
S
21
The "1" and "2" are buttons for memory position. Make
the actuator to the position where you want, push and
hold for 2 seconds then push button "1" or "2", the LED
will flash which means the memory function is done. The
memory function can only be recovered rather than
erased.
Memory Position Setting:
Hold the button "1" or "2", the actuator will operate to the
corresponding position then stop. The LED will flash
during the operating time and then extinguish when the
actuator reaches the corresponding position.
When button "1" or "2" is released before the actuator
reaches the corresponding position, the actuator will stop
and the LED will be extinguished.
Operating:
c 2014 Moteck. Printed in Taiwan. The contents of this publication are the copyright of the publisher and may not be copied or even extracted unless prior written permission is authorized.
1F-1, No.79, Sec.1 ,Xintai 5th Rd., Xizhi Dist.,
New Taipei City 22101, Taiwan (R.O.C.)
E-mail:[e-mail]
http://www.moteck.com.tw
TEL:[phone]
AX:[phone]
MO-FAM-1-I-011-140910A
F
2
S