MOTO GUZZI 2Q000297 Guide

SERVICE STATION MANUAL
2Q000297
V7 III ABS

SERVICE STATION
MANUAL
V7 III ABS
THE VALUE OF SERVICE
As a result of continuous updates and specific technical training programmes for Moto Guzzi products,
onlyMotoGuzziOfficialNetworkmechanicsknowthisvehiclefullyandhavethespecifictoolsnecessary
to carry out maintenance and repair operations correctly.
Thereliabilityofthevehiclealso dependsonitsmechanical conditions.Checkingthevehicle beforeriding
it, its regular maintenance and the use of original Moto Guzzi spare parts only are essential factors!
For information on the nearest Official Dealer and/or Service Centre consult our website:
www.motoguzzi.com
Only by requesting Moto Guzzi original spare parts can you be sure of purchasing products that were
developed and tested during the actual vehicle design stage. All Moto Guzzi original spare parts undergo
quality control procedures to guarantee reliability and durability.
Thedescriptionsandimagesinthispublicationaregivenforillustrativepurposesonlyandarenotbinding.
While the basic characteristics as described and illustrated in this booklet remain unchanged, Piaggio &
C.S.p.A. reserves theright, at anytime and withoutbeing required toupdate this publicationbeforehand,
to make any changes to components, parts or accessories, which it considers necessary to improve the
product or which are required for manufacturing or construction reasons.
Notallversions/modelsshowninthispublicationareavailableinallcountries.Theavailabilityofindividual
versions should be checked with the Official Moto Guzzi sales network.
The Moto Guzzi brand is owned by Piaggio & C. S.p.A.
© Copyright 2017 - Piaggio & C. S.p.A. All rights reserved. Reproduction of this publication in whole or
in part is prohibited.
Piaggio & C. S.p.A. Viale Rinaldo Piaggio, 25 - 56025 PONTEDERA (PI), Italy
www.piaggio.com

SERVICE STATION MANUAL
V7 III ABS
This manual provides the main information to carry out regular maintenance operations on your vehicle.
This manual is intended to Moto Guzzi Dealers and their qualified mechanics; several concepts have
been deliberately omitted as they are considered unnecessary. As it is not possible to include complete
mechanical notions in this manual, users should have basic mechanical knowledge or minimum
knowledge about the procedures involved when repairing scooters. Without this knowledge, repairing or
checking the vehicle may be inefficient or even dangerous. As the vehicle repair and check procedures
are not described in detail, be extremely cautious so as not to damage components or injure individuals.
In order to optimise customer satisfaction when using our vehicles, Moto Guzzi commits itself to
continually improve its products and the relative documentation. The main technical modifications and
changes in repair procedures are communicated to all Moto Guzzi Sales Outlets and its International
Subsidiaries.These changes willbe introduced inthe subsequent editionsof the manual.In case ofneed
or further queries on repair and check procedures, consult Moto Guzzi CUSTOMER DEPARTMENT,
which will be prepared to provide any information on the subject and any further communications on
updates and technical changes related to the vehicle.
NOTE Provides key information to make the procedure easier to understand and carry out.
CAUTION Refers to specific procedures to carry out for preventing damages to the vehicle.
WARNING Refers to specific procedures to carry out to prevent injuries to the repairer.
Personal safety Failure to completely observe these instructions will result in serious risk of personal
injury.
Safeguarding the environment Sectionsmarked withthis symbol indicate the correctuse of the vehicle
to prevent damaging the environment.
Vehicle intactness The incomplete or non-observance of these regulations leads to the risk of serious
damage to the vehicle and sometimes even the invalidity of the guarantee

INDEX OF TOPICS
CHARACTERISTICS CHAR
SPECIAL TOOLS S-TOOLS
MAINTENANCE MAIN
ELECTRICAL SYSTEM ELE SYS
ENGINE FROM VEHICLE ENG VE
ENGINE ENG
POWER SUPPLY P SUPP
SUSPENSIONS SUSP
CHASSIS CHAS
BRAKING SYSTEM BRAK SYS
BODYWORK BODYW
PRE-DELIVERY PRE DE

INDEX OF TOPICS
CHARACTERISTICS CHAR

Rules
Safety rules
Carbon monoxide
If you need to keep the engine running while working on the vehicle, please ensure that you do so in
an open or very well ventilated area. Never run the engine in an enclosed area. If you do work in an
enclosed area, make sure to use a fume extraction system.
CAUTION
EXHAUSTEMISSIONSCONTAINCARBONMONOXIDE, APOISONOUS GASWHICHCANCAUSE
LOSS OF CONSCIOUSNESS AND EVEN DEATH.
Fuel
CAUTION
THE FUEL USED TO POWER INTERNAL COMBUSTION ENGINES IS HIGHLY FLAMMABLE AND
MAY BE EXPLOSIVE UNDER CERTAIN CONDITIONS. IT IS THEREFORE RECOMMENDED TO
CARRY OUT REFUELLING AND MAINTENANCE PROCEDURES IN A VENTILATED AREA WITH
THEENGINE SWITCHEDOFF.DO NOTSMOKEDURING REFUELLING ORNEAR FUEL VAPOUR.
AVOIDANYCONTACTWITHNAKEDFLAME, SPARKS OR OTHER HEAT SOURCES WHICH MAY
CAUSE IGNITION OR EXPLOSION.
DO NOT ALLOW FUEL TO DISPERSE INTO THE ENVIRONMENT.
KEEP OUT OF THE REACH OF CHILDREN.
Hot components
The engine and the exhaust system components become very hot and remain hot for some time after
the engine has been switched off. When handling these components, wear insulating gloves or wait
until the engine and the exhaust system have cooled down.
Used engine oil and transmission oil
CAUTION
IT IS ADVISABLE TO WEAR PROTECTIVE IMPERMEABLE GLOVES WHEN SERVICING THE VE-
HICLE.
THE ENGINE OR GEARBOX OIL MAY CAUSE SERIOUS INJURIES TO THE SKIN IF HANDLED
FOR PROLONGED PERIODS OF TIME AND ON A REGULAR BASIS.
WASH YOUR HANDS CAREFULLY AFTER HANDLING OIL.
HAND THE OIL OVER TO OR HAVE IT COLLECTED BY THE NEAREST USED OIL RECYCLING
COMPANY OR THE SUPPLIER.
DO NOT DISPOSE OF OIL IN THE ENVIRONMENT
KEEP OUT OF THE REACH OF CHILDREN.
V7 III ABS Characteristics
CHAR - 7

Brake and clutch fluid
BRAKE AND CLUTCH FLUIDS CAN DAMAGE THE PLASTIC OR RUBBER PAINTED SURFACES.
WHEN SERVICING THE BRAKING OR THE CLUTCH SYSTEM PROTECT THESE COMPONENTS
WITH A CLEAN CLOTH. ALWAYS WEAR PROTECTIVE GOGGLES WHEN SERVICING THESE
SYSTEMS. BRAKE AND CLUTCH FLUIDS ARE EXTREMELY HARMFUL FOR YOUR EYES. IN
THE EVENT OF ACCIDENTAL CONTACT WITH THE EYES, RINSE THEM IMMEDIATELY WITH
PLENTY OF COLD, CLEAN WATER AND SEEK MEDICAL ADVICE.
KEEP OUT OF THE REACH OF CHILDREN.
Battery electrolyte and hydrogen gas
CAUTION
THE BATTERY ELECTROLYTE IS TOXIC, CORROSIVE AND AS IT CONTAINS SULPHURIC ACID,
IT CAN CAUSE BURNS WHEN IN CONTACT WITH THE SKIN. WHEN HANDLING BATTERY
ELECTROLYTE, WEAR TIGHT-FITTING GLOVES AND PROTECTIVE APPAREL. IN THE EVENT
OF SKIN CONTACT WITH THE ELECTROLYTIC FLUID, RINSE WELL WITH PLENTY OF CLEAN
WATER. IT IS PARTICULARLY IMPORTANT TO PROTECT YOUR EYES BECAUSE EVEN TINY
AMOUNTSOF BATTERYACIDMAY CAUSEBLINDNESS. IF THEFLUID GETSINCONTACT WITH
YOUR EYES, WASH WITH ABUNDANT WATER FOR FIFTEEN MINUTES AND CONSULT AN EYE
SPECIALIST IMMEDIATELY. THE BATTERY RELEASES EXPLOSIVE GASES; KEEP IT AWAY
FROM FLAMES, SPARKS, CIGARETTES OR ANY OTHER HEAT SOURCES. ENSURE ADE-
QUATE VENTILATION WHEN SERVICING OR RECHARGING THE BATTERY.
KEEP OUT OF THE REACH OF CHILDREN.
BATTERY LIQUID IS CORROSIVE. DO NOT POUR OR SPILL ON PLASTIC COMPONENTS IN
PARTICULAR. ENSURE THAT THE ELECTROLYTIC ACID IS COMPATIBLE WITH THE BATTERY
BEING ACTIVATED.
Maintenance rules
GENERAL PRECAUTIONS AND INFORMATION
When repairs, disassembly and reassembly of the vehicle is carried out, follow the following recom-
mendations strictly.
BEFORE DISASSEMBLING COMPONENTS
•Remove the dirt, mud, dust and foreign objects from the vehicle before disassembling com-
ponents. Wherever required, use the special tools designed for this vehicle.
DISASSEMBLING COMPONENTS
•Do not loosen and/or tighten the screws and nuts using pliers or other tools, but always use
the specific wrench.
•Mark the positions on all the connection joints (hoses, cables, etc.) before separating them
and identify them with different distinctive marks.
•Each piece should be clearly marked in order to be identified during the installation phase.
•Carefully clean and wash the disassembled components with detergents with a low flam-
mability grade.
Characteristics V7 III ABS
CHAR - 8

•Keep the coupled parts together because they have "adapted" to one another following
normal wear.
•Some components must be used together or replaced entirely.
•Keep away from heat sources.
REASSEMBLING COMPONENTS
CAUTION
BEARINGS MUST ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTHERWISE, THEY
NEED TO BE REPLACED.
•Only use ORIGINAL Moto Guzzi SPARE PARTS.
•Comply with lubricant and consumables use guidelines.
•Lubricate parts (whenever possible) before reassembling them.
•When tightening nuts and screws, start from the ones with the largest section or from the
internal ones, moving diagonally. Tighten nuts and screws in successive steps before ap-
plying the tightening torque.
•Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), cotter pins
and screws with new ones if their tread is damaged.
•When assembling the bearings, make sure to lubricate them well.
•Check that each component is assembled correctly.
•After a repair or routine maintenance procedure, carry out pre-ride checks and test the ve-
hicle on private grounds or in an area with low traffic density.
•Clean all coupling surfaces, oil guard rims and gaskets before refitting them. Smear a light
layer of lithium-based grease on the oil guard rims. Reassemble oil guards and bearings
with the brand or lot number facing outward (visible side).
ELECTRICAL CONNECTORS
Electric connectors must be disconnected as described below; failure to comply with this procedure
causes irreparable damage to both the connector and the wiring harness:
Press the relative safety clips, if applicable.
•Grip the two connectors and disconnect them by pulling them in opposite directions.
•If any signs of dirt, rust, moisture, etc. are noted, clean the inside of the connector carefully
with a jet of compressed air.
•Ensure that the cables are correctly fastened to the internal connector terminals.
•Then connect the two connectors, ensuring that they couple correctly (if fitted with clips, you
will hear them "click" into place).
CAUTION
DO NOT DISCONNECT CONNECTORS BY PULLING THE CABLES.
NOTE
THE TWO CONNECTORS CAN ONLY BE CONNECTED IN ONE DIRECTION: CONNECT THEM
THE RIGHT WAY ROUND.
TIGHTENING TORQUES
CAUTION
V7 III ABS Characteristics
CHAR - 9

IF UNSCREWING A SELF-LOCKING NUT, IT MUST BE REPLACED WITH A NEW ONE.
CAUTION
REMEMBER THAT THE TIGHTENING TORQUE FOR ALL THE FIXING ELEMENTS LOCATED ON
WHEELS, BRAKES, WHEEL AXLES AND OTHER SUSPENSION COMPONENTS PLAY A FUN-
DAMENTAL ROLE IN GUARANTEEING THE SAFETY OF THE VEHICLE AND MUST BE KEPT AT
THE PRESCRIBED VALUES. REGULARLY CHECK THE TIGHTENING TORQUE OF THE FIXING
ELEMENTS AND ALWAYS USE A TORQUE WRENCH WHEN REFITTING. IF THESE WARNINGS
ARE NOT OBSERVED, ONE OF THESE COMPONENTS COULD LOOSEN AND COME OFF,
BLOCKING A WHEEL OR CAUSING OTHER PROBLEMS THAT WOULD COMPROMISE MA-
NOEUVRABILITY, LEADING TO A CRASH WITH THE RISK OF SERIOUS INJURY OR EVEN
DEATH.
Running-in
Engine run-in is essential to ensure engine long life and correct operation. Twisty roads and gradients
are ideal to run in engine, brakes and suspensions effectively. Vary your riding speed during the run-
in. This ensures that components operate under both "loaded" and "unloaded" conditions, allowing the
engine components to cool.
CAUTION
THE CLUTCH MAY EMIT A SLIGHT BURNING SMELL WHEN FIRST USED. THIS PHENOMENON
SHOULD BE CONSIDERED NORMAL AND WILL DISAPPEAR AS SOON AS THE CLUTCH
PLATES GET ADAPTED.
ITIS IMPORTANTTO STRAINENGINECOMPONENTSDURINGRUN-IN, HOWEVER,MAKE SURE
NOT TO OVERDO THIS.
CAUTION
THE FULL PERFORMANCE OF THE VEHICLE IS ONLY AVAILABLE AFTER THE SERVICE AT
THE END OF THE RUNNING IN PERIOD.
Follow these guidelines:
•Do not twist the throttle grip abruptly and completely when the engine is working at a low
revs, either during or after run-in.
•During the first 100 Km (62 miles) use the brakes gently, avoiding sudden or prolonged
braking. That is to permit the adequate adjustment of the pad friction material to the brake
discs.
AFTER THE SPECIFIED MILEAGE, TAKE THE VEHICLE TO AN OFFICIAL Moto Guzzi DEALER
FOR THE CHECKS INDICATED IN THE "AFTER RUN-IN" TABLE IN THE SCHEDULED MAINTE-
NANCE SECTION TO AVOID INJURING YOURSELF, OTHERS AND /OR DAMAGING THE VEHI-
CLE.
Vehicle identification
SERIAL NUMBER LOCATION
These numbers are necessary for vehicle registration.
NOTE
ALTERING IDENTIFICATION NUMBERS MAY BE SERIOUSLY PUNISHABLE BY LAW. IN PAR-
TICULAR, MODIFYING THE CHASSIS NUMBER IMMEDIATELY VOIDS THE WARRANTY.
Characteristics V7 III ABS
CHAR - 10

CHASSIS NUMBER
The chassis number is stamped on the right hand
side of the headstock.
This number consists of numbers and letters, as in
the example shown below.
ZGULD00016MXXXXXX
KEY:
ZGU: WMI (World manufacturer identifier) code;
LD: model;
000: version;
0: free digit
16: variable year of manufacture (16 - for 2016)
M: production plant (M= Mandello del Lario);
XXXXXX: serial number (6 digits);
ENGINE NUMBER
The engine number is stamped on the left side,
close to the engine oil level check cap.
Dimensions and mass
WEIGHT AND DIMENSIONS
Specification Desc./Quantity
Max. length (Special/Stone/Racer) 2,185 mm (86.02 in)
Max. length (Anniversario) 2,235 mm (88.00 in)
Max. width (Special/Stone/Anniversario) 800 mm (31.50 in)
Max. width (Racer) 755 mm (29.72 in)
Max. height 1,100 mm (43.31 in)
Wheelbase 1,445 mm (56.89 in)
Kerb weight (Special/Anniversario) 213 kg (470 lb)
Kerb weight (Stone/Racer) 209 kg (461 lb)
Engine
ENGINE
Specification Desc./Quantity
Type traverse-mounted twin-cylinder four-stroke V 90°
Cylinder number 2
Displacement 744 cm³ (45.40 cu.in)
Bore / stroke 80x74 mm (3.15x2.91 in)
V7 III ABS Characteristics
CHAR - 11

Specification Desc./Quantity
Compression ratio 10.5 +/- 0.5: 1
Start up Electric
Engine idle speed 1,250 +/- 100 rpm
Clutch dry single-disc clutch with flexible coupling
Lubrication Pressure-fed, controlled by valves and trochoidal pump
Air filter cartridge-type dry filter
Cooling air
Transmission
GEARBOX
Specification Desc./Quantity
Type mechanical, 6 speeds with foot lever on the left hand side of
the engine
TRANSMISSION
Specification Desc./Quantity
Primary drive with gears, ratio: 18 / 23 = 1 : 1.277
Gear ratios, 1st gear 16 / 39 = 1 : 2.437
Gear ratios, 2nd gear 18 / 32 = 1 : 1.777
Gear ratios, 3rd gear 21 / 28 = 1 : 1.333
Gear ratios, 4th gear 24 / 26 = 1 : 1.083
Gear ratios, 5th gear 25 / 24 = 1 : 0.96
Gear ratios, 6th gear 28 / 24 = 1 : 0.857
Final drive with cardan shaft, ratio: 8 / 33 = 1 : 4.125
Capacities
CAPACITY
Specification Desc./Quantity
Fuel tank (reserve included) 21 l (4.62 UK gal; 5.55 US gal)
Fuel tank reserve 4 l (0.88 UK gal; 1.06 US gal)
Engine oil Oil change and oil filter replacement: 2,000 cm³ (122.05 cu.in)
Gearbox oil 500 cm³ (30.51 cu.in)
Transmission oil 170 cm³ (10.37 cu.in)
Maximum permissible weight (Stone/Racer) 419 kg (924 lb) (rider + passenger + luggage)
Maximum permissible weight (Special/Anniversario) 423 kg (933 lb) (rider + passenger + luggage)
Seats 2
Electrical system
ELECTRICAL SYSTEM
Specification Desc./Quantity
Battery 12 V - 12 Ah
Fuses 5 (2) - 15 (3) - 20 - 30 A
Permanent magnet alternator 12V - 268W
Low/high beam light (halogen) 12 V - 55 W / 60 W H4
Front daylight running lights 12 V - 5 W
tail light /stop lights 12 V - 5 / 21 W
Turn indicator light 12 V - 10 W (orange RY 10 W bulb)
SPARK PLUGS
Specification Desc./Quantity
Standard NGK CPR8EB-9
Spark plug electrode gap 0.9 mm (1.98 in)
Resistance 5 kOhm
Characteristics V7 III ABS
CHAR - 12

WARNING LIGHTS
Specification Desc./Quantity
Gearbox in neutral LED
Turn indicators LED
Fuel reserve LED
High beam light LED
General alarm LED
MI warning light LED
ABS Warning Light LED
MGCT warning light LED
Frame and suspensions
SIZES A AND B
Specification Desc./Quantity
Size A 692 mm (27.24 in)
Size B 186 mm (7.32 in)
FRAME
Specification Desc./Quantity
Type Modular double cradle, high-strength steel tubular chassis
Steering rake 26°
Trail (no rider or passenger - wheels on the ground - without
use of side stand) 106 mm (4.17 in)
SUSPENSIONS
Specification Desc./Quantity
Front hydraulic telescopic fork, Ø 40 mm (1.57 in)
Stroke 137 mm (5.39 in)
Rear Swingarm in die-cast light alloy, 2 shock absorbers with ad-
justable spring preloading
Stroke 80 mm (3.15 in)
Brakes
BRAKES
Specification Desc./Quantity
Front Ø 320-mm (12.59 in) stainless steel floating disc, calliper with
4 different and counteracting plungers
Rear 260 mm (10.24 in) stainless steel disc, floating calliper with two
22 mm (0.87 in) diameter pistons
V7 III ABS Characteristics
CHAR - 13

Wheels and tyres
WHEEL RIMS
Specification Desc./Quantity
Type (Special/Racer/Anniversario) with spokes with alloy rims, for tyres with inner tubes
Type (Stone) Alloy wheels for tubeless tyres
Front 2.5''x18''
Rear 3.50" x 17''
TYRES
Specification Desc./Quantity
Front tyre PIRELLI SPORT DEMON
Front (size) 100 / 90 - 18 56H
Front (size) (alternative) 110 / 80 - R18 58H
Front (inflation pressure) 2.5 bar (250 kPa) (36.26 PSI)
Front (inflation pressure with passenger) 2.6 bar (260 kPa) (37.71 PSI)
Rear tyre PIRELLI SPORT DEMON
Rear (size) 130 / 80 - 17 65H
Rear (inflation pressure) 2.5 bar (250 kPa) (36.26 PSI)
Rear (inflation pressure with passenger) 2.6 bar (260 kPa) (37.71 PSI)
Supply
FUEL SYSTEM
Specification Desc./Quantity
Type Electronic injection (Marelli MIU G3)
Venturi Ø 38 mm (1.50 in)
Fuel Unleaded petrol max E10 (95 RON).
Tightening Torques
Chassis
Characteristics V7 III ABS
CHAR - 14

Front side
FRONT SUSPENSION - STEERING
Pos. Description Type Quantity Torque Notes
1 Screws fastening stanchion on upper plate M8x35 4 25 Nm (18.44 lb ft) -
2 Steering head fastening bushing - 1 100 Nm (73.76 lb ft) -
3 Steering headstock lock nut - 1 50 Nm (36.88 lb ft) Pre-torque 60 Nm (44.25
lb ft)
4 Headstock counter-lock ring - 1 Manual -
5 Calliper bracket fixing screws M6x30 2 10 Nm (7.38 lb ft) -
V7 III ABS Characteristics
CHAR - 15

Pos. Description Type Quantity Torque Notes
6 Connector plate fastening screw M6x16 1 10 Nm (7.38 lb ft) -
7 Screws fastening stanchion on lower plate M10 2 45 Nm (33.19 lb ft) -
8 Pumping unit fastening screw M10 2 50 Nm (36.88 lb ft) -
INSTRUMENT PANEL
Pos. Description Type Quantity Torque Notes
1 Instrument cluster cover fastening screws Self-tap-
ping
4.2x19
4 2 Nm (1.48 lb ft) -
2 Screws fastening instrument cluster to support
bracket Self-tap- ping
3.9x16
6 2 Nm (1.48 lb ft) -
3 Support plate fastening screws M6 2 10 Nm (7.38 lb ft) -
Characteristics V7 III ABS
CHAR - 16

INSTRUMENT PANEL
Pos. Description Type Quantity Torque Notes
1 Instrument cluster cover fastening screws Self-tap-
ping
4.2x19
2 1.2 - 1.5 Nm (0.89 -
1.11 lb ft) -
2 Screws fastening instrument cluster to support
bracket Self-tap- ping
3.9x16
3 1.2 - 1.5 Nm (0.88 -
1.11 lb ft) -
3 Support plate fastening screws M6 2 10 Nm (7.38 lb ft) -
V7 III ABS Characteristics
CHAR - 17

HANDLEBAR AND CONTROLS
Pos. Description Type Quantity Torque Notes
1 Screw fixing handlebar support U-bolts to
steering plate M10 2 50 Nm (36.88 lb ft) -
2 Handlebar U-bolt fastener screws M8 4 25 Nm (18.44 lb ft) -
3 Mirror fixing M10 2 Manual -
- Light switch fastening screws SWP 5 2 1.5 Nm (1.11 lb ft) -
- Throttle cable cover fastening screws M5 3 6 Nm (4.43 lb ft) -
HANDLEBAR AND CONTROLS
Pos. Description Type Quantity Torque Notes
1 Switch fastener screw SWP 5 1+1 1.5 Nm (1.11 lb ft) -
2 Semi-handlebar fixing screw M6x25 4 10 Nm (7.38 lb ft) -
3 Counterweight fixing screw M6 2 10 Nm (7.38 lb ft) Loctite 243
4Screw fastening the clutch control U-bolt to
the semi-handlebar M6 2 10 Nm (7.38 lb ft) -
5 Mirror fixing M10 1 + 1 - Manual
- Gas covers fastener screw M5 3 6 Nm (4.43 lb ft) -
Characteristics V7 III ABS
CHAR - 18

FRONT BRAKE MASTER CYLINDER
Pos. Description Type Quantity Torque Notes
1 Front brake master cylinder U-bolt fixing
screws M6 2 10 Nm (7.38 lb ft) -
2 Brake light switch fastening screws M4 1 3 Nm (2.21 lb ft) -
FRONT LIGHTS
Pos. Description Type Quantity Torque Notes
1 Headlamp fastening screws M8 2 15 Nm (11.10 lb ft) -
V7 III ABS Characteristics
CHAR - 19

Pos. Description Type Quantity Torque Notes
2 Front turn indicators fastening screws M6 2 5 Nm (3.69 lb ft) -
3 Screws fastening the headlight support strips M6 2 10 Nm (7.38 lb ft) -
FRONT MUDGUARD
Pos. Description Type Quantity Torque Notes
1Screws fastening the stabiliser plate to the fork M8 4 15 Nm (11.06 lb ft) Loctite 243
2 Screw fastening the mudguard to the stabiliser
plate M6 4 10 Nm (7.38 lb ft) Loctite 243
Characteristics V7 III ABS
CHAR - 20