MOTO GUZZI Breva 1100 User manual

1
Contents
Contents
Breva
Breva 1100 1100
Æ
ÆAspects and vehicle characteristics Aspects and vehicle characteristics
Æ
ÆGeneral data General data
Æ
ÆDashboard and immobilizer Dashboard and immobilizer
Æ
ÆElectronic injection, description and functioning Electronic injection, description and functioning
Æ
ÆEngine Engine
Æ
ÆNew electro New electro- -mechanical components mechanical components
Æ
ÆDiagnosis Diagnosis - -Axone Axone
Æ
ÆBalancing throttle bodies Balancing throttle bodies

2
Aspect
Aspect and and vehicle vehicle characteristics characteristics

3
Total view of vehicle :
dimensions
Aspect
Aspect and and vehicle vehicle characteristics characteristics

4
Aspect
Aspect and and vehicle vehicle characteristics characteristics
General
General data data
Weight: 248 Kg
Output: max. KW 63,0 at 7500 rpm
Torque: Nm 85,0 a 6800 rpm
Maximum speed in 6th gear 210 Km/h
Front tire: 120/70 ZR17 (58W) pressure 1/2 persons 250kPa±10
Rear tire: 180/55 ZR17 (73W) pressure 1/2 persons 280kPa±10
Injection/ignition system MAGNETI MARELLI
Computer IAW 5AM2 with map alfa/n

5
Aspect
Aspect and and vehicle vehicle characteristics characteristics
Frame
ZGULP...

6
Aspect
Aspect and and vehicle vehicle characteristics characteristics
Capacity 23 l ±0,5 l
Material Nylon
Fuel tank
Fuel pump

7
Aspect
Aspect and and vehicle vehicle characteristics characteristics
Front brakes
Double calipers and discs
Rear brakes

8
Aspect
Aspect and and vehicle vehicle characteristics characteristics
Additional equipment.
Accessories
Accessories (optional): (optional):
-
-Windscreen; ;
-
-Carrying Carrying Case Case adjustable adjustable in in height height; ;
-
-Side Side bags bags
-
-Alarm Alarm systems systems ( (not not yet yet available available) )

9
Dashboard
Dashboard

10
Dashboard : identifying areas
Dashboard : identifying areas
Rev counter:
Positioned at the left, final range 10.000 rpm.
At the end of the scale is a red warning light (Led) without
monogram to indicate to shift gear when surpassing a preset
level rpm. The rpm activation level can be adjusted via the users
interface.

11
Dashboard : identifying areas
Dashboard : identifying areas
Fuel level
indicator Under
the fuel warning
light sits a red
warning light
without pictogram
(Led) for the
eventual alarm
system. .
Speedometer at the center
Multifunctional
Multifunctional Display Display

12
Dashboard : identifying areas
Dashboard : identifying areas
Fuel level indicator
The dashboard is connected to a variable resistor.Measurements that fall out of the
normal operating range are considered as faults and are signalled by the diagnostics.
The indications show at the instrument panel at the right and the spare indicator
underneath.
The characteristics and measurement curve can be found in the repair manual.
•Quantity LITRES OHM
•8/8 22.50 10-20 appr.
•4/8 11.25 100 appr.
•0 0 250-300 appr.
The spare indicator lights up at values higher than 230 ohm
After 2 km it shows the amount of km driven after the indicator light
came on.

13
Led indicators
From left to right:
- Indicator green, left hand indicator
- Indicator orange, ABS faulty (CURRENTLY NOT ACTIVE)
- Indicator red, Alarm: engine oil pressure problem, EFI and w/ vehicle OFF indicator
immobilizer.
- Indicator green, Neutral position
- Indicator yellow, vehicle stand down
- Indicator blue, beam lights on
- Indicator green, right hand indicator
Dashboard : identifying areas
Dashboard : identifying areas

14
Dashboard: indicators and lights
Dashboard: indicators and lights
Direction indicators.
•The dashboards controls the indicator lights, as well for the single indications left
and right as for the combined circuits for the “Hazard”function.
•Indications for problems with circuits ( bulb burnt or short circuited) by doubling the
flashing frequency of the warning light and with indication on the dashboard left or
right
Activation/deactivation of the Hazard function
This function can only be activated or deactivated with the key in ON position
Control of beam lights
The light relay will only be operated by the engine ECU when the rpm exceeds 800

15
The commands to move between various dashboards functions are obtained by a three
position selector at the light switch at the left hand steering handle.
The selector has following
three positions:
-Trip1
-Trip2
- Mode
In the first position will show the data of TRIP1,
In the second the data of TRIP2
While in the third position MODE, one can access to the functions of dashboard
configurations.
Dashboard: selections
Dashboard: selections

16
Dashboard: display
Dashboard: display
Basic information
•On the display appear as well the basic information as the information activated by the
selector position. These are:
•Clock. Clock settings can be 12 or 24 hour indications, where 12 hour indications
show AM or PM.
•Odometer. A 6 digit number in km or miles, according to user selection.
•Ambient temperature. Shows in the upper left corner of the LCD. When the temperature
is close to zero, a icing symbol will show (next slide). Finally one can show the
temperature in °C or °F selectable by the user.
Clock Display

17
Dashboard: display
Dashboard: display
Handles heater (OPTIONAL)
With engine running, by pressing insisting at command handles heating, an icon will
show at the display that substitutes the selected trip indication. That will be transferred to
the central part of the display. With every short pulse a three positions bar will grow
indicating the power level present in the handles heating. When the engine is stopped the
heater will be switched off. At the next vehicle usage the handles heater will reposition at
the ultimate setting.

18
ÄThe immobilizer system is integrated in the electronic dashboard.
ÄAt key-to-ON the dashboard will read the key code. If the code corresponds to the
one memorized, the dashboard will activate the initial check and will allow the
ECU for engine starting, via the CAN Bus line.
ÄIf the key code is not recognized, the dashboard will not permit for engine starting
and on the display will appear the request to insert the code to allow for
“manually” engine starting.
ÄTo the customer will be delivered two keys with transponder, already memorized
from the factory and at every key-to-ON the dashboard will ask to insert the
personal 5 digit code, if not yet done:
you must remember to insert the user code
ÄTo insert the personal code one must select the function CODE MODIFICATION
Dashboard: immobilizer
Dashboard: immobilizer

19
Dashboard : display
Dashboard : display
Trip 1-2
In these two positions of the display are demonstrated the data relevant for
trips 1 and 2.
In the central area is constantly displayed the partial distance covered while in the
lower portion the following data will be shown in rotation:
•Trip time
•Average Fuel consumption of the trip
•Current consumption
•Maximum speed
•Average speed
A short pulse will change the indications between one and the other, keeping the
switch pressed longer will reset all values to zero for the selected trip.
Consumption is expressed in litres per 100 kilometres or in miles per gallon
For detailed functioning please read with attention the workshop manual information.

20
Dashboard : MODE
Dashboard : MODE
Mode
in this position you can select the other functions of the dashboard with the vehicle
stopped and thus with speed equal to Zero with every short pulse of the switch SET you
can see in sequence the following functions:
stopwatch battery voltage Menu
The selection of the functions is affected by holding the SET switch for a longer period.
For detailed functioning of the stopwatch please read with attention the workshop manual