Motorline professional MR27 Use and care manual

1
2
3
4 5
6
9
714 810
11
12
13
V3.0
REV. 04/2017
1
A
B
C
A
B
C
EN
AC/DC
12-36V
(Relay)
COM
NC
BROWN
YELLOW
GREEN
WHITE
RED
BLACK
5
6
COM
NO (Relay)
MOVEMENT
PRESENCE
1Cover 6Angle of Inclination’s Indicator 11 Main connector
2Base 7Radar Module 12 Infrared Ajusting Area
3Lens 8Radar’s Sensitivity Regulator 13 NO/NC Jumper
4Transmitter 9Activation Indicator 14 Microwave relay
Jumper
5Receptor 10 Safety Indicator
TECHNICAL SPECIFICATIONS CHARACTERISTICS BOARD
• RADAR DESCRIPTION
• CONNECTION DIAGRAM | JUMPERS
RADAR
PRESENCE SENSOR
The MR27 is a 2 in 1 sensors radar - Radar and photocells
combined in a single product.
2 output relays - Motion and Presence. Developed for automatic
sliding and revolving doors.
With Self-Learning Function of the infrared sensor's action
area. It allows to adapt automatically to changes in the area of
infrared detection as well as fluctuations, distortion, movement,
darkness and lightness.
This product adopts a microwave sensor with german origin, and
it is not influenced by temperature and humidity, ensuring a
reliable and safe performance.
For installations up to 2.5 meters high.
• Power Supply AC/DC 12 to 30V (-/+10%)
• Output 2 Relays
• Current (STANDBY) 65mA
• Current (Action) 130mA
• Cable Length 2500mm
• Instalation Max Height 2500mm
• Cover’s Material ABS
• Technology Processor
• Frequency 24.125GHz
• Emission <20dBm EIRP
• Transmission frequency density <5mW/cm2
• Detection Mode Movement
• Detection Range 4m (W) x 2m (D)
• Output Time 0.5s
• Temperature -20°C to 55°C
• Ray Type Refleted Infrared
• Ray Source Infrared 940mm
• Ray Quantity 8 emitted, 8 emitted
• Self-Learning Time 60 sec.
• Operation’s Indicator Standby (blue)/ Activ. (red)
• Temperature -40⁰c to 60⁰C
• Detection Area 1600 (W) x 800 (D) mm
• Output Time 500ms
• Reply ≤100ms
• Optical Surface PMMA
MR27 | USER'S AND INSTALLER'S MANUAL
A and B - NO Contact
B and C - NC Contact
A and B - The microwave relay is activa-
ted by infrared relay at the same time.
B and C - The microwave relay is not acti-
vated by infrared relay.
13
14

00.201.01.5 0.8
0.8
1.3
1.6
1.9
2.2
2.5
1.3
1.6
1.9
2.2
2.5
01 212
3
2
1
0
15°
30°
45°
15°
30°
45°
0°
15°30°45°
2.5m
00.201.01.5 0.8
0.8
1.3
1.6
1.9
2.2
2.5
1.3
1.6
1.9
2.2
2.5
01 212
3
2
1
0
15°
30°
45°
15°
30°
45°
0°
15°30°45°
2.5m
Plastic Post
Cable/Wire
EN
RADAR INSTALLATION ADJUST SENSITIVITY
Alignment between radar and safe's upper limit.
01. Place the radar centered with the safe's cover and aligned by the upper limit. Mark the place for the
holes.
For a detection area nearest the door turn the poten-
tiometer in a clockwise direction.
For a detection area farthest from the door turn the
potentiometer counterclockwise.
Increase Sensitivity - Rotate in a clockwise direction
Reduce Sensitivity - Rotate counter-clockwise direction.
02. Make the holes.
04. Make a hole on the top of the safe. Pass the cable through the hole made and connect it to the exis-
ting connector inside the radar.
05. Put back the cover on the safe and apply the radar cover.
03. Tighten the radar in the holes with screws.
01. Please ensure that the area is object’s free
during the process of the sensor’s self-learning.
03. If after 60 seconds and no movement occurs
within the infrared’s area, the sensor will accept
the object as part of the room and closes the door.
Width
Width
Safety Area of Presence Detection: Width & Depth:
RADAR
PRESENCE/
FOTOCELLS
SENSOR
Radar Ativation Area: Width & Depth:
Depth
Depth
02. The door will open if an object is placed in the
detection area
04. Remove the object. The system will send a
environment reading signal and return to the
original recording background.
• PRESENCE SENSOR’S DETECTION AREA
• PRESENCE DETECTION AREA
• RADAR SENSIBILITY ADJUSTMENT
• RADAR AND PRESENCE DETECTION
MR27 | USER'S AND INSTALLER'S MANUAL