Motorline professional Cofre 260 Operation and installation manual

COFRE 260

INSTALLER AND USER´S MANUAL

v1.2

REV. 08/2015

 Centralization via radio through transmitter

The centralization of two or more control boards via radio allows simultaneous

movement of ascending or descending of more awnings.

The centralization is performed by entering the same codes keys from a transmitter to

all control boards at maximum distance of  meters from the transmitter point in, in

order to get the general or partial motion of more automations. For a satisfactory radio

centralization, you must choose carefully the location of installation.

The operating range is not only related with the technical characteristics of the device,

it may vary depending on the radioelectric conditions of the location.

 Presence Light operation with remote control

It is also possible to program a remote control channel to turn on or off a Vac lamp

at a distance, connected to connectors of the board  CN.

 Automatic LimitSwitch when opening/closing

There is, in the control board, an limitswitch automatic system to use in the awning.

Whenever it is identified an excessive current absorption by one motor during

opening/closing, due to the possible presence of an obstacle or the complete

movement of opening/closing, the control board stops immediately the maneuver and

relieves.

 Programming buttons and indicator LEDs

SEL key: selects the type of function to be memorized, the choice is indicated by the

flashing of the LED. Pressing the button more times, it is possible to position yourself in

the desired function. The flashing LED indicates that the selection is active, but the

duration is  seconds. At the end of this period, the control board returns to its normal

status.

SET button: makes the choosen programming with the SEL button.

LED signaling

LED on: option saved.

LED off: option not saved.

Intermittent LED: option selected.

 Main menu

CODE Programming the remote control to operate the awning and the wireless Wind

Sensor

CODE LAMP Programming the remote control to operate a lamp

T.MOT Programming the Working Time/ motor

 Programming the remote control  or  keys and Wireless Sensor

The programming of the transmission codes of the remote control is performed as

following: press the SEL button and CODE LED will blink. At the same time, send the

first code closing selected with the desired remote control. The LED CODE will flash

rapidly.

Send the second code opening to be memorized, the LED CODE will remain ON and

programmation is finished. If the second code is not sent within  seconds from the

first one, the unit exits the programming phase, leaving only a button on the remote

control to work step by step open/stop/close.

 Programming wireless sensor sun/wind/rain

If you want to memorize a wireless sensor, follow these steps:

º Turn ON the power supply of the sensor;

º Open the memory of the control board MC. For this step we have two options:

option   Open the control board as follows: use the SEL button to go to the LED

CODE. option   With the awning openned and lighting turned off, continually

press the remote’s opening channel memorized for more than  seconds until the

light of the awning flashes once;

After opening the control board’s memory, you have  seconds to send the

sensor’s order to the control board.

º Sensor Use the SEL button to go to the LED CODE led starts to blink,

immediately press the SET button of the sensor so that it emits a rapid flashing of

the LED CODE until the light of the awning flashes once;

º With the SEL button of the sensor, you must now select the functions you want

to leave activated in the sensor the sun/wind/rain. Press SEL repeatedly until the

LED of the desired function flashes. With the LED flashing, press the SET button

for more than  second until it is fixed LED turned on = active function.

To disable any function, repeat point  but press the SET button

at least for  second and the LED goes out, leaving the

function disabled.

º To test the sensor you should follow

the next instructions:

Use the SEL button to go to the LED

CODE led starts to blink. Press the SET

button for more than  second and the LED

stays on.

TEST RAIN SENSOR Place a wet finger over the

sensor until the awning begins to close the

awning will close during  seconds.

TEST WIND SENSOR Rotate the propeller. The awning will close

for  seconds.

TEST SUN SENSOR Turn VRclockwise + and the awning will open for  seconds.

Turn the VR counterclockwise  and the awning will close for  seconds.

In case the awning performs the indicated operations successfully, the sensor is

programmed and the test finished.

You must deactivate the LED TEST so that, in case of emergency, the awning

closes entirely. If the LED TEST stays on, the awning will only close for  seconds.

When the awning closes by sensor’s order, we can see what order is being sent,

checking which LED of the sensor is ON, on the board’s monitor.

For more information on how to adjust the wind speed, sensitivity and sensor’s

illuminance, read the manual of Wiweather sensor.

To reset the sensor, simultaneously press the SEL and SET buttons of the sensor for

 seconds. All LEDs light on and the sensor is back to the factory programming.

 Functions deactivation sun/rain via remote control

If you want to disable the Sun/Rain functions, please begin by opening the awning and

before the awning finishes the opening by the limit switch, press the transmitter, the

awning will stop immediately and turn off the Sun/Rain functions. However, whenever

the awning does not fully open by being stopped with the remote control, the Sun/Rain

functions are disabled and the Wind function remains active.

To reactivate the functions, let the awning fully open.

 Maximum number of memorable Wireless Sensors

The control board can only memorize  Wireless Sensor. Programming a new Wireless

Sensor will delete the previously memorized code.

 Poor communication of the Sensor

In case of poor of communication between the Wireless Sensor and MC control board,

the opening/closing will be automatically activated after  minutes. If poor

communication continues, other remote controls will keep the control board in a state

of security, not allowing the awning to open when receives opening order, it opens a

little bit and returns to the point of closed. If the sensor is active with  functions sun,

rain and wind, where there sun,  minutes after sends the awning open. When the

sun finished  minutes later sends the awning collapse. During the time that the

awning is open, in case of rain or wind the awning collects.

CODE LAMP Programming the remote control for operating the light output

The programming of the channels of the remote control is performed as follows:

Use the SEL button to go to the CODE LAMP LED led starts to blink. Then

send the desired channel of remote control. LED CODE LAMP remains lit and

programming is complete.

T. MOT. Programming working time   minutes max.

The control board is supplied with LED T.MOT. OFF, meaning that the motor time is 

minutes. With T.MOT LED. OFF and the remote control programmed, we can move the

awning in the opening/closing direction, until you make the adjustment of the limit

switches. Follow the instructions. The Working Time must always be set.

The programming of the working time must be performed with a fully open

awning.

Programming the working time with limit

switches only in opening and closing by

effort is performed as follows:

Disadjust completely the closing limit switch

for the awning to close the full course and

stop by effort.

Programming motor’s time is performed as

follows:

With the awning openned and already with the

opening limit switch adjusted, position the SEL

button to LED T. MOT, press and keep pressing the

SET button and the awning starts to close.

When the awning finishes the closing and the

motor turns off, release the SET button, and the

working time is now defined and the LED

T.MOTstays on.

When it is intended that the awning stops on

opening and closing by limit switch, with the open

awning and the two limit switches fully regulated,

with the SEL button, make the LED T.MOT flash and

press without releasing SET button until the awning closes and the motor stops by limit switch.

Wait more  seconds and release the SET button. LED T.MOT will illuminate and working time will

be programmed.

 Extended Menu 

The control board is supplied by the manufacturer with the possibility of selecting only the main

menu functions. To enable the functions described in menu , proceed as follows: press the SET

button continuously for  seconds and then there is the alternating flashing of the LEDs CODE

LAMP and LED T. MOT, in this mode, you have  seconds to select the  menu functions through

the use of SEL and SET buttons, after  seconds, the control board returns to the main menu.

01.A 01.B

STANDARDS TO FOLLOW 

 INDEX

00. CONTENT 01. SAFETY INSTRUCTIONS

ATTENTION:

 To ensure the people’s safety, it is important that you read all the following

instructions. Incorrect installation or incorrect use of the product can cause physical

injury and material damage.

 Keep these instructions in a safe place for future reference.

 This product was designed and produced strictly for the use indicated in

this manual. Any other use, not expressly indicated here, could compromise the good

condition/operation of the product and/or be a source of danger.

 ELECTROCELOS S.A. is not responsible for the improper use of the

product, or other use than that for which it was designed.

 ELECTROCELOS S.A. is not responsible if safety standards were not taken

into account when installing the equipment, or for any deformation that may occur to it.

 ELECTROCELOS S.A. is not responsible for the safety and proper opera-

tion when using components not sold by them.

 Do not make any modiﬁcations to the operator components and / or their

accessories.

 Before installation unplug the automatism from the source of power.

 Do not perform the installation before adverse climatic conditions (wind,

rain, snow).

 The installer must inform the client how to handle the product in case of

emergency and provide this manual to user.

 Keep transmitters away from children, to prevent the automated system

from being activated involuntarily.

 The customer shall not, under any circumstances, attempt to repair or tune

the operator. Must call qualiﬁed technician only.

 Connect the awning to a 230V plug with ground wire.