Motorline professional RAP200MT User manual

v2.0
REV. 05/2021
RAP200MTRAP200MT EN
USER’S AND INSTALER’S MANUAL

1A 1B
1B
4A
4A
4B
4B
4B
5
6A
8A
9
6A
7A
7A
7B
7B
8A
ENEN
00. CONTENT 01. SAFETY INSTRUCTIONS
INDEX
01. SAFETY INSTRUCTIONS This product is certified in accordance with European
Community (EC) safety standards.
This product complies with Directive 2011/65/EU of the
European Parliament and of the Council, of 8 June 2011, on
the restriction of the use of certain hazardous substances
in electrical and electronic equipment and with Delegated
Directive (EU) 2015/863 from Commission.
(Applicable in countries with recycling systems).
This marking on the product or literature indicates that the
product and electronic accessories (eg. Charger, USB cable,
electronic material, controls, etc.) should not be disposed
of as other household waste at the end of its useful life. To
avoid possible harm to the environment or human health
resulting from the uncontrolled disposal of waste, separate
these items from other types of waste and recycle them
responsibly to promote the sustainable reuse of material
resources. Home users should contact the dealer where
they purchased this product or the National Environment
Agency for details on where and how they can take these
items for environmentally safe recycling. Business users
should contact their vendor and check the terms and
conditions of the purchase agreement. This product and
its electronic accessories should not be mixed with other
commercial waste.
This marking indicates that the product and electronic
accessories (eg. charger, USB cable, electronic material,
controls, etc.) are susceptible to electric shock by direct or
indirect contact with electricity. Be cautious when handling
theproductandobserveallsafetyproceduresinthismanual.
ATTENTION:
RAP200MT
TECHNICAL CHARACTERISTICS
DESCRIPTION
DIMENSIONS
LED INDICATIONS
INSTALLATION AND CONNECTIONS
SENSOR CONFIGURATION
DETECTION AREA ADJUSTMENT
INSTRUCTIONS FOR FINAL CONSUMERS / SPECIALIZED TECHNICIANS
02. THE PRODUCT
03. INSTALLATION
04. CONFIGURATION
05. TROUBLESHOOTING
PROGRAMMABLE PARAMETERS
SENSITIVITY
VEHICLE DETECTION
DETECTION OF HUMAN PRESENCE
REACTION TO PRESENCE
PRESENCE DETECTION

2EN
01. SAFETY INSTRUCTIONS
GENERAL WARNINGS
•This manual contains very important safety and usage information.
very important. Read all instructions carefully before beginning the
installation/usage procedures and keep this manual in a safe place
that it can be consulted whenever necessary.
•This product is intended for use only as described in this manual. Any
other enforcement or operation that is not mentioned is expressly
prohibited, as it may damage the product and put people at risk
causing serious injuries.
•Thismanual is intendedfirstlyforspecialized technicians, and does not
invalidate the user’s responsibility to read the “User Norms” section in
order to ensure the correct functioning of the product.
•The installation and repair of this product may be done by qualified
and specialized technicians, to assure every procedure are carried
out in accordance with applicable rules and norms. Nonprofessional
and inexperienced users are expressly prohibited of taking any action,
unless explicitly requested by specialized technicians to do so.
•Installations must be frequently inspected for unbalance and the
wear signals of the cables, springs, hinges, wheels, supports and other
mechanical assembly parts.
•Do not use the product if it is necessary repair or adjustment is
required.
•When performing maintenance, cleaning and replacement of parts,
the product must be disconnected from power supply. Also including
any operation that requires opening the product cover.
•The use, cleaning and maintenance of this product may be carried
out by any persons aged eight years old and over and persons whose
physical,sensorialormentalcapacitiesarelower,orbypersonswithout
any knowledge of the product, provided that these are supervision
and instructions given by persons with experienced in terms of usage
of the product in a safe manner and who understands the risks and
dangers involved.
•Children shouldn’t play with the product or opening devices to avoid
the motorized door or gate from being triggered involuntarily.
WARNINGS FOR TECHNICIANS
•Before beginning the installation procedures, make sure that you have
all the devices and materials necessary to complete the installation
of the product.
•You should note your Protection Index (IP) and operating temperature
to ensure that is suitable for the installation site.
•Provide the manual of the product to the user and let them know how
to handle it in an emergency.
•If the automatism is installed on a gate with a pedestrian door, a door
locking mechanism must be installed while the gate is in motion.
•Do not install the product “upside down” or supported by elements do
not support its weight. If necessary, add brackets at strategic points
to ensure the safety of the automatism.
•Do not install the product in explosive site.
•Safety devices must protect the possible crushing, cutting, transport
and danger areas of the motorized door or gate.
•Verify that the elements to be automated (gates, door, windows,
blinds, etc.) are in perfect function, aligned and level. Also verify if the
necessary mechanical stops are in the appropriate places.
•The centralmust be installed on asafe place of any fluid(rain, moisture,
etc.), dust and pests.
•You must route the various electrical cables through protective tubes,
to protect them against mechanical exertions, essentially on the
power supply cable. Please note that all the cables must enter the
central from the bottom.
•If the automatism is to be installed at a height of more than 2,5m from
the ground or other level of access, the minimum safety and health
requirements for the use of work equipment workers at the work of
Directive 2009/104/CE of European Parliament and of the Council of 16

3EN
September 2009.
•Attach the permanent label for the manual release as close as possible
to the release mechanism.
•Disconnect means, such as a switch or circuit breaker on the electrical
panel, must be provided on the product’s fixed power supply leads in
accordance with the installation rules.
•If the product to be installed requires power supply of 230Vac or
110Vac, ensure that connection is to an electrical panel with ground
connection.
•The product is only powered by low voltage satefy with central (only
at 24V motors)
WARNINGS FOR USERS
•Keep this manual in a safe place to be consulted whenever necessary.
•If the product has contact with fluids without being prepared, it must
immediately disconnect from the power supply to avoid short circuits,
and consult a specialized technician.
•Ensure that technician has provided you the product manual and
informed you how to handle the product in an emergency.
•Ifthesystemrequiresanyrepairormodification,unlocktheautomatism,
turn off the power and do not use it until all safety conditions have
been met.
•In the event of tripping of circuits breakers of fuse failure, locate
the malfunction and solve it before resetting the circuit breaker or
replacing the fuse. If the malfunction is not repairable by consult this
manual, contact a technician.
•Keep the operation area of the motorized gate free while the gate in in
motion, and do not create strength to the gate movement.
Do not perform any operation on mechanical elements or hinges if the
product is in motion.
RESPONSABILITY
•Supplier disclaims any liability if:
•Product failure or deformation result from improper installation
use or maintenance!
•Safety norms are not followed in the installation, use and
maintenance of the product.
•Instructions in this manual are not followed.
•Damaged is caused by unauthorized modifications
•In these cases, the warranty is voided.
01. SAFETY INSTRUCTIONS
SYMBOLS LEGEND:
• Important safety
notices
• Useful information
• Programming
information
• Potentiometer
information
• Connectors
information
• Buttons
information

4A 4B
ENEN
02. THE PRODUCT
• Power Supply 12-36 Vdc | 12-28 Vac
• Technology Microwave
• Maximum installation height 7 meters
• Consumption < 1W
• Stand-by consumption < 50mA a 24 Vdc
• Adjustment angles Up/Down: 15 ° | 30 ° | 45 °
Right/Left: ± 18 °
• Detection area
7m (W) x 7m (D) in installations with a height of 5m and an angle
of 45 °
5m (W) x 8m (D) in installations with a height of 7m and an angle
of 45 °
• Operating frequency 24,250 GHz
• Relay output 2 relay outputs, NO / NC: Voltage: Max 48 Vdc
• Relay waiting time 0.5 - 300 seconds
• Operating temperature -25°C to +55°C
• Operating humidity ≤ 90%
• IP IP67
• Construction Polycarbonate (PC)
• Weight 320g (without cable), 650g (with cable)
RAPMT
The RAPMT is an ideal microwave radar for large doors and places with high ceilings, and
can be installed up to m height. It has detection technology capable of differentiating people
and vehicles, reducing unwanted openings, thus saving energy loss.
TECHNICAL CHARACTERISTICS
. THE PRODUCT
DESCRIPTION
Green On hold
Flashing Green/Red alternately Sensor is starting
Flashing green (fast) Human presence relay activated
Flashing red (fast) Vehicle presence relay activated
Flashing Green/Red alternately (fast) Human presence and vehicle relay activated
Red LED
Green LED
[Configuration] button
Rotation screw
Mounting bracket
[Function] button
mm
mm
mm
mm
When using the sensor programming buttons (present in the front zone), the number of times
the red LED flashes (slow) followed by the number of times the green LED flashes (slow)
indicates the function of the sensor and its configuration.
LED INDICATIONS
DIMENSIONS
•  User
Manual •  Cable
•  Fixing
screws