Motorola MBP35 User manual

USER’S GUIDE
MBP35
BABY MONITOR
USER’S GUIDE
The features described in this user’s guide are subject to
modifications without prior notice.
V 0.1

This User’s Guide provides you with all the information you need
to get the most from your product.
Before you can use the baby monitor, you’ll need to insert and
fully charge the battery on the Parent unit. Please read the Safety
Instructions on page 6 before you install the units.
Got everything?
• 1 x Parent unit
• 1 x Baby unit
• 1 x Rechargeable Ni-MH battery pack for the Parent unit
• 1 x Power adapter for the Parent unit
• 1 x Power adapter for the Baby unit
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied
with your product. We recommend the batteries to be installed
before use, so that the unit continues to work in the event of a
mains power failure.
Welcome...
to your new Motorola Baby Monitor!
Thank you for purchasing the MBP35. Now you can see and hear
your baby sleeping in the other room or you can monitor your older
children in their playroom.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide
a copy of your dated sales receipt to confirm warranty status.
Registration is not required for warranty coverage.
For product related questions, please call:
0845 218 0890 in the UK
Onthe Web:www.motorola.com

5
6
7
2
1
3 4
TALK MENU
12
11
10 9 8
13
1. Display (LCD screen)
2. Up </Down key >
Normal mode: Adjust
speaker volume
Menu mode: Adjust setting
3. Power and Low battery LED
4. VOX LED (for voice activation)
5. Lullaby Play/Stop key i
Press once to play lullaby.
Press again to stop playing.
6. Lullaby selection key j
Press to select a lullaby
during playback.
7. Microphone
8. Menu key m
Press to open the Menu
options
9. Talk key t
Press and hold to speak to
your baby.
10. Power key p
Press to turn on the unit.
Press and hold to turn it off.
11. Antenna
12. Battery cover
13. Speaker
Overview of your Parent unit
Parent unit display symbols
Indicates that the baby unit is out of range
Appears when setting the temperature reading or during temperature reading
Indicates that the temperature is too high
Indicates that the temperature is too low
Appears when setting the Night Light function
Indicates that the talk function is activated
Appears when playing lullabies
Appears when changing the lullaby
Appears when adjusting the volume of the parent unit
Appears when adjusting the brightness of the LCD

1
2
3
4
5
9
8
7
6
Overview of your Baby unit
1. Photo sensor
2. Camera lens
3. Infrared LEDs
4. Power LED
5. Night lights
6. On/Off switch
7. Speaker
8. Antenna
9. Temperature sensor

Table of contents 5
ENGLISH
Table of contents
1. Safety Instructions ......................................................................... 6
2. Getting started................................................................................ 7
2.1 Baby unit battery installation...........................................................7
2.2 Baby unit power supply ..................................................................8
2.3 Parent unit battery Installation ........................................................8
2.4 Parent unit power supply................................................................9
2.5 Registration ..................................................................................10
3. Using the Baby Monitor MBP35 .................................................. 11
3.1 Setting up .....................................................................................11
3.2 Night vision ...................................................................................11
3.3 Talk function .................................................................................11
3.4 Adjusting the volume of the parent unit ........................................11
3.5 Playing a lullaby for your baby......................................................11
4. MBP35 Parent Unit Menu Options .............................................. 13
4.1 Brightness.....................................................................................13
4.2 Temperature display (ºC or ºF).....................................................13
4.3 Night Light ....................................................................................13
4.4 Voice Activation ............................................................................13
5. Disposal of the device (environment) ........................................ 15
6. Cleaning ........................................................................................ 16
7. Help................................................................................................ 17
8. General Information ..................................................................... 18

6 Safety Instructions
1. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s
Guide, safe to use. Therefore, always read the instructions in this User’s
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the cot or within arm's reach of
the baby (the unit should be at least 1 metre away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power
adapters provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and
batteries.
• Only insert batteries of the same type. Never use ordinary, non-
rechargeable batteries in the parent unit. Insert batteries with the right
polarity (indicated in the battery compartment).
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.

Getting started 7
ENGLISH
2. Getting started
2.1 Baby unit battery installation
The camera uses either 3 AA size batteries (non-rechargeable batteries
recommended) or the household power mains. The Baby unit has no
charging function!
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied with
your product. We recommend the batteries to be installed before use, so
that the unit continues to work in the event of a mains power failure.
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Install the 3 AA non-rechargeable batteries following the polarity as
shown in the compartment. Close the battery compartment and
tighten the screw in a clockwise direction.
3. Slide the power switch to the
ON position. The power LED will light up
in green.
To switch off the baby unit, slide the power switch to the
OFF position.
NOTE
When the battery level is low, the power LED will turn orange and will flash.
WARNING
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit batteries or dispose of in fire.
Remove the batteries if this device is not going to be used for a long
period of time.
screw

8 Getting started
2.2 Baby unit power supply
1. Connect the small plug of the power adapter to the baby unit and the
other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 1000mA).
2. Slide the power switch to the
ON position. The power LED will light up
in green.
3. To switch off the baby unit, slide the power switch to
OFF position.
2.3 Parent unit battery Installation
Black Red screw

Getting started 9
ENGLISH
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Insert the wire tab of the rechargeable battery pack into the contact
slot as shown above and fit the battery pack into the compartment.
3. Close the battery compartment and tighten the screw in a clockwise
direction.
4. Press ponce to switch ON the parent unit.
- It will take a few seconds to start up the unit.
5. Press and hold pto switch OFF the parent unit.
NOTE
When the battery level is low, the power LED will turn orange and will flash.
NOTE
When the unit is powered up with either the power adapter or using the
rechargeable battery pack, the LED will light up in green. If both the power
adapter and rechargeable battery pack are used, the LED will light up in red.
2.4 Parent unit power supply
1. Connect the small plug of the power adapter to the parent unit and
the other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 1000mA).
2. Press pto switch ON the parent unit. The power LED will light up
in green.
3. Press and hold pto switch OFF the parent unit.

10 Getting started
NOTE
Once the baby and parent units are switched on, the display on the parent
unit will show the video captured by the baby unit.
When there is no connection or out of range, the icon on the LCD
display will flash and the parent unit will beep continuously. Move the
parent unit closer to the baby unit until the link is re-established.
2.5 Registration
The baby monitor is already pre-registered upon your purchase. You do
not need to re-register it again unless the baby unit loses its link with the
parent unit.
To re-register your baby monitor, follow the procedure below:
1. Switch off both the baby and parent units.
2. Press and hold mfor more than 5 seconds while the parent unit
mains power is switched back on, and then press pat the same
time to switch it on. The parent unit is in registration mode.
3. Cover the camera lens on the baby unit with a black cloth or bag and
then switch it on.
4. Wait for the 2 units to search and establish the link.
5. Remove the cover on the baby unit.
The registration is complete when the display screen on the parent unit
captures the video from the baby unit’s camera.