Motorola VM36XL User manual

5.0" HD Video Baby Monitor with Touch Screen
For: VM36XL TOUCH CONNECT
User Guide
Lorem Ipsum

Safety instructions
WARNING
Strangulation Hazard. Children have STRANGLED in cords.
Keep this cord out of the reach of children (more than 3 ft (1 m)
away). Never use extension cords with AC Adaptors. Only use
the AC Adaptors provided.

Baby monitor setup and use:
• Choose a location for the baby unit that will provide the best view of your
baby in their crib.
• Place the baby unit on a flat surface, such as a dresser, desk, shelf or mount
the unit securely using the flexible grip or tripod mount screw hole on the
underside of the stand.
• NEVER place the baby unit or cords in the crib or within reach of the baby
(the unit and cords should be more than 3 feet away).
WARNING
This Smart Video Baby Monitor is compliant with all relevant standards
regarding electromagnetic fields and is, when handled as described in the User
Guide, safe to use. Therefore, always read the instructions in this User Guide
carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User Guide for future reference.
• Do not place the baby (camera) unit or cords in the crib or within reach of
the baby (the unit and cords should be more than 3 feet away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel, blanket, or other item that will
stop air circulation.
• Never use extension cords with power adaptors. Only use the power
adaptors provided.
• Test this monitor and all its functions so that you are familiar with it prior to
actual use.
• Do not use the baby monitor near water or allow water or other foreign
substances to enter the power port or adaptor.
• Do not place the Baby Monitor near a heat source.
• Only use the chargers and power adaptors provided. Do not use other
chargers or power adaptors as this may damage the device and battery
packs.
• Do not touch the plug contacts with sharp or metal objects.
• The unit should be set up and used so that parts of the user's body other
than the hands are maintained at a distance of approximately 8 inches
(20 cm) or more.
CAUTION
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.

Welcome...
to your new Smart Video Baby Monitor!
Thank you for purchasing your new Smart Nursery product. Now you can
see and hear your baby sleeping in another room or you can monitor your
older children in their playroom.
Important
To use your baby and parent units together, you must be able to establish
a radio link between them, and the range will be aected by environmental
conditions.
Any large metal object, like a refrigerator, a mirror, a filing cabinet, a
metallic door or reinforced concrete between the baby and parent units
may block the radio signal.
The signal strength may also be reduced by other solid structures, like
walls, or by radio or electrical equipment, such as TVs, computers, cordless
or mobile phones, fluorescent lights or dimmer switches.
Other 2.4GHz products, such as wireless networks (Wi-Fi® routers),
Bluetooth™ systems, microwave ovens or other baby monitors, may cause
interference with this product, so keep the baby monitor at least 5 ft (1.5 m)
away from these types of products, or switch them o if they appear to be
causing interference.
If the signal is weak, try moving the parent and/or the baby unit(s) to
dierent positions in rooms.
Need help?
If you have any problems setting up or using your VM36XL TOUCH
CONNECT, please visit us at: motorolanursery.com/support
Alternatively, you may find the answer in the ‘Help’ section at the back of
this guide.

This User Guide provides you with all the information
you need to get the most from your Smart Video
Baby Monitor.
Read the instructions carefully, and be aware that
this Smart Video Baby Monitor is only intended as an
aid. It is not a substitute for responsible and proper
adult supervision.
Before you use the Smart Video Baby Monitor, set
up the parent and baby units. Follow the simple
instructions in ‘Getting started’, on the next few
pages.
Important
Only use the power adaptors supplied.
Got everything?
• Parent unit with built-in rechargeable Lithium-ion battery (2000 mAh)
• Baby (camera) unit
• AC power adaptor for the parent unit
• AC power adaptor for the baby (camera) unit
If you have purchased multi camera pack, you will also have the following
additional items:
• Baby (camera) unit(s)
• AC power adaptor(s) for the baby (camera) unit(s)
For Wi-Fi® internet viewing you will need a suitable Android or iPhone/iPad
device and Wi-Fi® internet connection of at least 0.6 Mbps upload bandwidth
per baby (camera) unit.

6
1. Getting started ................................................................... 7
2. Getting to know your baby monitor ..........................11
3. Using the video baby monitor.................................... 14
3.1 Use the touch screen......................................................................................14
3.2 Adjust the brightness on the parent unit ...............................................15
3.3 Zoom the screen ..............................................................................................15
3.4 Enable audio media playback.....................................................................15
3.4.1 Pre-recorded personal content playback...............................15
3.4.2 Lullabies/soothe sounds playback............................................15
3.4.3 English audio book playback ......................................................15
3.4.4 Adjust the volume level of audio playback............................15
3.5 Turn the flashlight on or o .........................................................................15
3.6 Set the timer ......................................................................................................16
3.7 Two-way talk......................................................................................................16
3.8 Use the camera .................................................................................................16
3.8.1 Pair or add a camera with the parent unit .............................16
3.8.2 View a camera...................................................................................16
3.8.3 Remove a camera ............................................................................16
3.8.4 Use the patrol mode .......................................................................17
3.9 Set the temperature unit...............................................................................17
3.10 Power saving mode.........................................................................................17
3.11 View multiple camera on screen................................................................17
3.12 Default settings ...............................................................................................17
4. Viewing the baby through your device....................18
4.1 Minimum System Requirements.................................................................18
4.2 Connect your device.......................................................................................18
4.3 Set up the camera............................................................................................19
4.3.1 Set up user account and camera on your devices..............19
4.3.2 Connect the Camera.......................................................................19
4.3.3 Download the App ..........................................................................19
4.3.4 Sign up or log in to the App........................................................19
4.3.5 Add a camera to your account................................................. 20
4.4 Reset the camera ........................................................................................... 20
5 Help........................................................................................21
6. Technical Specifications................................................23
7. General information....................................................... 24

7
1. Getting started
Location
Important
Do not place your VM36XL TOUCH CONNECT in the bathroom or other humid
areas.
Place your units within reach of the AC power outlet and wall socket. The
socket-outlet should be installed near the equipment and should be easily
accessible.
Setting up
Important
The baby (camera) unit must be plugged into the wall socket at all times. Use
only the AC power adaptor supplied with the product.
Getting started

8
Connecting the baby (camera) unit
You will need to carry out this process for the single or multi baby (camera)
units.
1. Plug the USB type-C plug of the power adaptor into the power socket
on the rear of the baby (camera) unit and plug the other end of the AC
adaptor into the wall socket.
2. Switch on the AC power.
Getting started

9
Connecting and charging the parent unit
A rechargeable battery is already pre-installed inside the parent unit. When
fully charged, you can move the parent unit without losing the link and picture
from the baby (camera) unit.
Important
Warning! Use only the approved rechargeable Lithium-ion battery
(2000mAh) supplied with your VM36XL TOUCH CONNECT.
1. Plug the USB type-C plug of the power adaptor into the power socket on
the side of the parent unit and plug the other end of the AC adaptor into
the wall socket.
2. Switch on the AC power.
3. When charging the batteries for the first time, charge for at least 16 hours
continuously.
4. Press and hold the power button on the top of the parent unit to turn it on.
5. When the parent unit is fully charged, will appear steadily on the
display.
6. Flip out the stand on the back of the parent unit and rotate it by 90
degrees to set up the desktop stand.
Getting started

10 Getting started
Battery low warning
If is shown on the display, recharge the parent unit before using it again.
When charging, will scroll on the display.
Battery performance
In ideal conditions, fully charged batteries should give up to 5 hours usage
time.
The charge capacity of the rechargeable battery will reduce with time as it
wears out, giving the parent unit less usage / standby time. Eventually it will
need to be replaced.
Batteries and the parent unit may become warm during charging. This is
normal.
Your VM36XL TOUCH CONNECT is now ready for use.

11
2. Getting to know your baby monitor
Overview of your baby unit (camera)
1. Photo sensor (night vision mode)
2. Camera lens
3. Infrared LEDs (x8, for night vision)
4. Power LED
It turns on when linked to the parent unit.
5. Microphone
6. Power on/o switch
7. Temperature sensor
8. Power socket
9. PAIR button (bottom)
10. Speaker
11. Flexible grip mounting screw hole
12. Antenna
Getting to know your baby monitor

12
Overview of your parent unit
Front view Back view
1. Microphone
2. Power button
Press and hold to turn the parent unit on or o.
3. Volume down
Press to decrease the volume level.
4. Volume up
Press to increase the volume level.
5. Touch screen display
6. Sound Level LEDs (green, amber, red)
7. Charging LED
It becomes red when connected to the wall socket.
8. Speaker
9. Power socket
10. Reset key (recessed - use small pin)
11. Ring stand
12. Antenna
13. Flashlight
Getting to know your baby monitor

13
Display icons
Indicates the current signal strength level (4 levels).
Indicates the night vision mode is on. The video turns black and white.
Indicates the screen o time is set.
Volume level setting (8 levels) is in progress.
Unable to detect the baby (camera) unit.
Indicates the current battery level (4 levels).
Note
Depending on the video settings, the display will go blank after 5 minutes, 15
minutes, or 30 minutes to save power.
Registering the baby (camera) unit to the parent unit
(Pairing)
The video baby monitor is pre-registered to your parent unit. You do not need
to register it again unless the baby (camera) unit loses its link with the parent
unit.
To re-register your baby (camera) unit, see the following steps.
1. Tap on the menu bar.
2. Tap and / / / will pop up.
3. Tap / / / to select a desired camera. The parent unit starts
searching the baby (camera) unit.
Note
A baby (camera) unit can be paired only to one parent unit each time. If a baby
(camera) unit is currently paired with the parent unit, it will appear in dark grey
on the screen and cannot be selected for a new registration.
4. Press and hold PAIR on the underside of the baby (camera) unit until the
parent unit finds the baby (camera) unit and Pair OK appears on the screen.
The video from the baby (camera) unit will then appear.
Getting to know your baby monitor

14
3. Using the video baby monitor
3.1 Use the touch screen
• Swipe up at the screen bottom to pop up the menu bar. Swipe down at the
screen bottom to hide the menu bar.
• Scroll left or right on the menu bar to see all options.
• Swipe left or right to pan the camera view.
• Swipe up or down to tilt the camera view.
Note
The touch screen can be operated normally during camera viewing but it stops
functioning when the menu bar is displayed.
If you place the parent and baby (camera) units too close together, you may
hear a high pitched noise. This is not a fault. The units are designed to be
operated at some distance apart, e.g. in separate rooms, so move the units
further apart.
If is displayed on the screen, the parent and baby (camera) units are not
linked to each other. Make sure that both units are powered on.
Using the video baby monitor

15Using the video baby monitor
3.2 Adjust the brightness on the parent unit
1. Tap on the menu bar of the parent unit. The brightness status bar pops
up.
2. Tap / or swipe the brightness status bar left or right to select the
brightness level. There are 8 levels to choose from.
3.3 Zoom the screen
1. Tap on the menu bar of the parent unit. The zoom status bar pops up.
2. Tap / or swipe the zoom status bar left or right to select 1x or 4x
zoom.
3.4 Enable audio media playback
You can play back pre-recorded personal or preloaded audio content (lullabies,
soothing sounds and English audio books) on the baby (camera) unit to
soothe the baby. There are 10 preloaded lullabies/soothing sounds and 10
audio books in the baby (camera) unit.
3.4.1 Pre-recorded personal content playback
You can play back your personal content after recording the audio through the
App.
1. Tap on the menu bar of the parent unit. The options menu pops up.
2. Tap to view the names of your recordings displaying on the screen.
3. Tap to select a desired recording and start/stop playback.
3.4.2 Lullabies/soothe sounds playback
1. Tap on the menu bar of the parent unit. The options menu pops up.
2. Tap to view the names of lullabies or soothe sounds displaying on the
screen.
3. Tap to select a desired lullaby or soothe sound and start/stop playback.
3.4.3 English audio book playback
1. Tap on the menu bar of the parent unit. The options menu pops up.
2. Tap to view the names of audio books displaying on the screen.
3. Tap to select a desired audio book and start/stop playback.
3.4.4 Adjust the volume level of audio playback
1. Tap on the menu bar of the parent unit. The options menu pops up.
2. Tap on the option menu. The volume status bar pops up.
3. Tap or to select the volume level. There are 4 levels to choose from.
3.5 Turn the flashlight on or o
Tap on the menu bar of the parent unit to turn on/o the flashlight.

16
3.6 Set the timer
You can set timers on the parent unit to remind you or caregivers of the time
to feed the baby, change the baby’s diaper or put the baby to bed.
1. Tap on the menu bar of the parent unit.
2. Tap on to turn on the timer, then tap or to select the time. Each key
press represents an interval of 15 minutes, up to an interval of 6 hours.
3. If the next feeding time is 4 hours later, press or to adjust the timer
until 04:00 is displayed.
4. Tap set to confirm the time, will appear on the status bar.
5. The parent unit will beep when the time limit is reached. Press any key to
stop the timer.
3.7 Two-way talk
You can use the Talk Back feature to comfort and reassure your baby. Whilst
using Talk Back you will not be able to hear your baby until you release the
button.
1. Tap on the menu bar of the parent unit, Touch to talk will be displayed
on the screen.
2. Tap to talk to your baby through the parent unit's speaker. Tap on
the screen when you finish speaking.
3. Tap on the menu bar to turn o the talk back feature.
3.8 Use the camera
3.8.1 Pair or add a camera with the parent unit
See 'Registering the baby (camera) unit to the parent unit (Pairing)' on
page 13.
3.8.2 View a camera
1. Tap on the menu bar of the parent unit.
2. Tap and / / / will pop up.
3. Tap / / / to select a desired camera to view the picture
from that camera. The selected camera will appear in dark grey on the
screen.
3.8.3 Remove a camera
1. Tap on the menu bar of the parent unit.
2. Tap and / / / will pop up.
3. Tap / / / to select a desired camera to remove it from
registration.
Note
You cannot remove the camera if it is the only registered camera in the parent
unit.
Using the video baby monitor

17Using the digital audio baby monitor
3.8.4 Use the patrol mode
This function is available if you have more than one baby (camera) unit.
1. Tap on the menu bar of the parent unit.
2. Tap and / / / will pop up.
3. The screen will display images from dierent registered cameras every 12
seconds.
3.9 Set the temperature unit
The baby (camera) unit has a temperature sensor that can detect the baby
room temperature.
1. Tap on the menu bar of the parent unit. ° C / ° F will pop up on the screen.
2. Tap ° C or ° F to confirm the temperature format.
3.10 Power saving mode
1. Tap the in the menu bar of the parent unit, the screen o timer: o , 5m ,
15m or 30m (m = minutes) will pop up.
2. Select a screen o time.
3. The screen will be o after the time limit is reached.
4. Tap once on the screen to wake it up. Tap twice to open the menu bar.
Note
You can still hear the audio when the screen is o.
3.11 View multiple camera on screen
This function is available if you have more than one baby (camera) unit. When
the split screen function is on, you can view multiple cameras on the screen
and have a list of options.
• To turn on or o the split screen function, tap on the menu bar of the
parent unit.
• To select another screen, tap on the selected screen once.
• To hide or display the menu bar of that screen, tap on the selected screen
twice.
3.12 Default settings
Audio playback volume level 2
Brightness 4
Flashlight O
Temperature unit °F
Lullaby 1
Power saving 5 mins
Audio book 1
Temperature range 1 °C ~ 36 °C or 34 °F ~ 97 °F

18
4. Viewing the baby through your device
4.1 Minimum System Requirements
Android™ System
• Version 7.0 or above
iPhone®/iPad® iOS
• Version 10.0 or above
High Speed (Wi-Fi®) Internet
• At least 0.6 Mbps upload bandwidth per camera (you can test your internet
speed on this site: http://www.speedtest.net).
4.2 Connect your device
When a user tries to access the Wi-Fi® camera (baby unit), our server
authenticates the user’s identity and permits access to the Wi-Fi® camera
(baby unit).
Note
You can only set up through a compatible smartphone or tablet but not
through a PC.
Wi-Fi®
camera
Wi-Fi®
router
Outer Access your camera locally
View your camera from any
compatible device remotely
Service
Viewing the baby through your device

19
Viewing the baby through your device
4.3 Set up the camera
Connect the Wi-Fi® camera (baby unit) to the power adaptor, then plug into
the wall socket. The camera must be within range of the Wi-Fi® router with
which you want to connect. Make sure the password of the router is available
for entering during the in-app setup process.
The following table shows the meanings of dierent LED connection status.
State LED indication
Pair / Setup Flashes blue and red
Connected Solid blue
Video streaming Flashes blue
4.3.1 Set up user account and camera on your devices
You will need:
• Wi-Fi® camera (baby unit)
• Power adaptor for the camera
• Device with Android™ system version 7.0 and above, or
• iPhone®/iPad® with iOS version 10.0 and above
4.3.2 Connect the Camera
1. Switch o the parent unit before connecting the camera (baby unit) to
Wi-Fi®.
2. Connect the power adaptor to the power outlet and insert the plug into the
power socket on the back of the camera (baby unit). The camera turns on.
4.3.3 Download the App
1. Scan the QR code with your smart device and download the Motorola
Nursery App from App Store for iOS devices or from Google Play™ Store
for Android™ devices.
2. Install the App on your device.
4.3.4 Sign up or log in to the App
1. Ensure that your smart device is connected to your Wi-Fi® router.
2. Follow the on-screen instructions to run and sign up or log in to the APP.

20
4.3.5 Add a camera to your account
1. Log in to the APP.
2. Tap Devices , and then tap on the device screen to add a new camera.
3. Tap (your baby monitor model's name) to add the new camera.
4. Select and enter the password of your Wi-Fi® network and then tap Next .
5. Power on the camera.
6. Press and hold PAIR at the bottom of the camera. The LED flashes blue and
red.
7. Tap Continue on your device when you hear the voice prompt ' Ready for
pairing
'.
8. Tap Generate QR code on your device and hold the QR code 15 cm to 30 cm
in front of the camera to get scanned till you will hear a confirmation
message '
Pairing success ' from your device.
9. Tap Complete when it is successfully connected. It may take a few minutes
for the camera to connect to the Wi-Fi® network.
10. If connection fails, tap Retry and repeat steps 1 - 10 in this section.
4.4 Reset the camera
You will need to reset your camera if you relocate your camera from one router
to another.
1. Press and hold PAIR for about 20 seconds. Release it when you hear the
voice prompt '
Reset camera '. The camera is reset successfully.
2. Follow the section 4.3.5 to add the camera again.
Viewing the baby through your device