Motorola C1 User manual

Warning: Charge the handset for 24 hours before use.
Motorola C1
For C1011, C1012, C1013 and C1014
Digital CordlessTelephone with
Digital Answering Machine

Welcome...
to your new Motorola C1 Digital Cordless Telephone with
Digital Answering Machine!
• All handsets are fully cordless for locating anywhere within range.
• 50 Name and Number phonebook.
• Digital answering machine with 12 minutes recording time for high
quality message recording.
• Caller ID shows you who’s calling and see details of the last 40 callers in
a Calls list.1
• Redial up to 10 of the last numbers called.
• Register up to 5 handsets to a single base and register each handset with
up to 4 different bases.
• Make internal calls and transfer external calls between handsets.
• Choose from 5 different ringtones for internal and external calls as well
as numbers stored in the phonebook.
Need help?
If you have any problems setting up or using your C1, please contact
Customer Services on XXXX XXXXXXX.
Alternatively, you may nd the answer in the ‘Help’ section at the back of
this guide.
Please note that this equipment is not designed for making emergency
telephone calls when the power fails. Alternative arrangements should be
made for access to emergency services.
1You must subscribe to your network provider’s Caller ID or Call Waiting
service for these features to work. A subscription fee may be payable.

This user guide provides you with all the information you need
to get the most from your phone.
To set up your phone, follow the simple instructions in ‘Getting
Started’, on the next few pages.
IMPORTANT
Only use the telephone line cord supplied.
Got everything?
• C1 base & cordless handset
• 2 x rechargeable Ni-MH battery cells
• Power adaptor for the base
• Telephone line cord
If you have purchased a C1 multiple pack you will also have the following
additional items:
• Cordless handset & charger
• 2 x rechargeable Ni-MH battery cells
• Power adaptor for the charger
ECOMOTO: a convergence of efforts by marketing, design, research,
engineering and supply chain management that leads to better
products for everyone. A holistic view that focuses on both social and
environmental responsibility. A passion and a shared point of view.
The right thing to do.
• Meets and / or exceeds EMEA environmental regulatory requirements.
• Eco friendly packaging with a minimum 20% post consumer recycled
content.
• Phone housing is built with a minimum of 25% post consumer recycled
content plastic.
• Energy efcient charger that meets EU Code of Conduct requirements.
• ECO mode function which reduces the transmitted power and energy
consumption, please refer to page 28.

4
1. Getting started........................................................ 7
2. Getting to know your phone ............................... 11
3. Using the phone.................................................... 17
3.1 Switch the handset on / off .......................................................... 17
3.2 Calls................................................................................................ 17
3.2.1 Make a call........................................................................... 17
3.2.2 Preparatory dialling ............................................................ 17
3.2.3 End a call.............................................................................. 17
3.2.4 Receive a call....................................................................... 17
3.3 Adjust the earpiece volume ......................................................... 17
3.4 Mute ............................................................................................... 18
3.5 Intercom......................................................................................... 18
3.5.1 Make an internal call........................................................... 18
3.5.2 Receive an internal call....................................................... 18
3.5.3 Transfer a call...................................................................... 18
3.5.4 3-way conference call ......................................................... 18
3.6 Redial ............................................................................................. 19
3.6.1 View or dial an entry........................................................... 19
3.6.2 Copy a Redial list number to the phonebook ................... 19
3.6.3 Delete an entry .................................................................... 19
3.6.4 Delete the entire Redial list ................................................ 19
3.7 Lock / unlock the keypad .............................................................. 20
3.8 Paging / Find handset ................................................................... 20
4. Phonebook............................................................. 21
4.1 Store a name and number ........................................................... 21
4.2 View or dial an entry..................................................................... 22
4.3 Edit a name and number.............................................................. 22
4.4 Delete an entry .............................................................................. 22
5. Handset settings................................................... 23
5.1 Handset ringer volume................................................................. 23
5.2 Handset ringer melody................................................................. 23
5.3 Auto answer .................................................................................. 23
5.4 Handset name ............................................................................... 24
5.5 Language ....................................................................................... 24
5.6 Key beep ........................................................................................ 24
5.7 Battery low warning beep ............................................................ 24
5.8 Out of range warning beep .......................................................... 25
5.9 Keypad lock using the menu........................................................ 25
6. Base settings......................................................... 26
6.1 Base ringer volume....................................................................... 26
6.2 Base ringer melody....................................................................... 26

5
6.3 Change base PIN code.................................................................. 26
6.4 Dial mode....................................................................................... 27
6.5 Recall mode................................................................................... 27
6.6 Restore default settings................................................................ 27
6.7 Emergency default........................................................................ 27
6.8 ECO mode...................................................................................... 28
6.9 Default settings ............................................................................ 29
7. Clock & alarm........................................................ 30
7.1 Set the date.................................................................................... 30
7.2 Set the time ................................................................................... 30
7.3 Set alarm ....................................................................................... 30
7.4 Switch off alarm ring .................................................................... 30
8. Caller ID and the Calls list .................................... 31
8.1 Caller ID ......................................................................................... 31
8.2 Calls list.......................................................................................... 31
8.2.1 View the Calls list................................................................ 31
8.2.2 Dial a number in the Calls list ............................................ 32
8.2.3 Copy a Calls list number to the phonebook...................... 32
8.2.4 Delete an entry .................................................................... 32
8.2.5 Delete the entire Calls list................................................... 32
9. Using additional handsets ................................... 33
9.1 Registering an additional handset............................................... 33
9.2 Register a different make of handset to your C1 base............... 34
9.3 Select a base ................................................................................. 34
9.4 De-register a handset.................................................................... 34
10. Using the answering machine............................. 35
10.1 Set the answering machine day and time .................................. 35
10.2 Check the current day and time setting ...................................... 35
10.3 Switch the answering machine on / off ..................................... 35
10.4 Listening to your messages ........................................................ 36
10.5 Adjust the speaker volume .......................................................... 37
10.6 Record your own OGM................................................................. 37
10.7 Answer Only.................................................................................. 37
10.8 Select the OGM............................................................................. 38
10.9 Re-instate the pre-recorded OGM ............................................... 38
10.10 Answer delay ................................................................................ 38
10.11 Time saver..................................................................................... 39
10.12 Record a memo............................................................................. 39
10.13 Call screening ............................................................................... 39
10.14 Memory full................................................................................... 39

6
11. Using remote access ............................................ 40
11.1 Operating your answering
machine from another phone...................................................... 40
11.2 Set the security PIN code ............................................................. 41
11.3 Check security code...................................................................... 41
12. Help........................................................................ 42
13. General information ............................................. 44

7
Getting started
1. Getting started
IMPORTANT
Do not place your C1 in the bathroom or other humid areas.
Location
You need to place your C1 base within 2 metres of the mains power socket
and 1.8 metres from the telephone wall socket so that the cables will reach.
The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Make sure that it is at least 1 metre away from other electrical appliances
to avoid interference.Your C1 works by sending radio signals between the
handset and base.The strength of the signal depends on where you place
the base. Placing it as high as possible ensures the best signal.
HANDSET RANGE
The unit has a range of up to 300 metres outdoors when there is a clear line
of sight between the base and handset. Any obstruction between the base
and handset will reduce the range signicantly. With the base indoors and
the handset either indoors or outdoors, the range will normally be up to 50
metres.Thick concrete and stone walls can severely affect the range.
SIGNAL STRENGTH
The icon on your handset indicates that you are within range of the base.
When out of range of the base, the icon ashes. If you are on a call, you
will hear a warning beep.
The line will hang up if the handset moves out of range of the base. Move
closer to the base.The handset will automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all times. Do not
connect the telephone line cord into the wall socket until the handset is fully
charged. Use only the power adaptor and telephone line cord supplied with
the product.

8
Getting started
Connecting the base
1. Plug the telephone line cord into the socket marked on the underside
of the base.
2. Plug the power adaptor into the socket marked on the underside of
the base and plug the other end into the mains power wall socket. Switch
on the mains power.
Installing and charging the handset
1. Remove the battery cover from the back of the handset and insert the
rechargeable Ni-MH battery cells supplied. Please note the ’+’ and
’-’ markings inside the battery compartment and insert in the correct
direction.
2. Slide the battery cover back into place.
3. If you are charging the batteries for the rst time, place the handset on
the base to charge for at least 24 hours continuously.
4. When the handset is fully charged, icon will appear steady on the
display. Plug the other end of the telephone line cord (make sure that one
end is already plugged into the base) into the telephone wall socket.
Press
down
1
Slide
2

9
Getting started
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry out this process
for all the handsets and chargers.
1. Plug the power adaptor into the socket marked on the underside of
the charger and plug the other end into the mains power wall socket.
2. Remove the battery cover from the back of the handset and insert the
2 x AAA NiMH rechargeable batteries supplied. Please note the ’+’ and
’-’ markings inside the battery compartment and insert in the correct
direction.
3. Slide the battery cover back into place.
4. If you are charging the batteries for the rst time, place the handset on
the charger to charge for at least 24 hours continuously.
5. When the handset is fully charged, icon will appear steady on the
display.The display will show
HANDSET and handset number (e.g. 2) to
indicate that it is registered to the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery cells (2 x AAA
Ni-MH 450mA rechargeable batteries) supplied with your C1.
BATTERY LOW WARNING
If icon ashes on the display and you hear a warning beep every
minute during a call, you will need to recharge the handset before you can
use it again.
When charging, icon will scroll on the display.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to 10 hours talk
time or up to 200 hours standby time on a single charge.1

10
Getting started
Note that new batteries do not reach their full capacity until they have been
put to normal use for several days.
To keep your batteries in the best condition, leave the handset off the base
for a few hours at a time.
Running the batteries right down at least once a week will help them last as
long as possible.
The charge capacity of rechargeable batteries will reduce with time as they
wear out, giving the handset less talk / standby time. Eventually they will
need to be replaced.
After charging your handset for the rst time, subsequent charging time is
about 6–8 hours a day. Batteries and handset may become warm during
charging.This is normal.
1All talk and standby times are approximate and depend on features selected
and usage pattern.
Date and time
If you have subscribed to a Caller ID Service, the date and time is set
automatically for all handsets when you receive your rst call.
If you do not have a Caller ID service, you can set the date and time
manually.
Set the date manually:
1. Press , scroll to
DATE -- TIME and press .The display shows
DATE SET .
2. Press to select.
3. Enter the date (e.g. 12--08 for 12th of August) and press to conrm.
Set the time manually:
1. Press , scroll to
DATE -- TIME and press .
2. Scroll to
CLOCK SET and press .
3. Enter the time in 24 hour format (e.g. 18--30 for 6:30pm) and press
to conrm.
Your C1 is now ready for use.

11
Getting to know your phone
2. Getting to know your phone
Overview of your handset
A Earpiece
B Display
See page 13 for an overview of the display icons.
C Up
During a call, press to increase earpiece volume, page 17.
When the phone is ringing, press to increase the handset ringer
volume, page 23.
Press to scroll through the menu options, redial list, calls list and
phonebook entries.
D Menu / OK / Mute
Press to open the Menu, page 15.
Press to select menu options and to conrm a displayed option.
During a call, press to turn mute on / off, page 18.
E Talk
Press to make and receive calls, page 17.
A
B
C
D
E
F
G
H
I
J
K
M
L
N

12
Getting to know your phone
F * / Keypad lock
Press and hold to lock the keypad, page 20.
To unlock, press any key and follow the on screen instructions.
G Recall
Use with switchboard / PABX services and some network services.
H Redial
In standby mode, press to open the redial list.
I Phonebook / Delete / Back
In standby mode, press to open the phonebook menu, page 21.
In editing mode, press to delete characters and digits.
Go back to the previous menu level.
J Calls list / Down
In standby mode, press to open the calls list, page 31.
During a call, press to decrease earpiece volume, page 17.
When the phone is ringing, press to decrease the handset ringer volume,
page 23.
Press to scroll through the menu options, redial list, calls list and
phonebook entries.
K End Call / Exit / Switch Handset on / off
Press to end a call, page 17.
When viewing the redial / calls list / phonebook or when in the menu,
press to exit and return to standby.
Press and hold for 3 seconds to switch the handset on / off.
L Pause / #
Press and hold to enter a pause (P) when pre-dialling or storing numbers.
Dial a #.
M Intercom
Used to make internal calls and transfer calls to other C1 handsets
registered to the base, page 18.
N Microphone

13
Getting to know your phone
Battery
status
Scrolls
when
charging
Time or Handset name
In standby mode, press and hold to switch handset
0
idle screen between handset name or time.
Eco mode
Circle around
appears when
Eco mode is ON
Handset LCD Display
Flashes to indicate an incoming external call.
External call in progress.
Flashes to indicate an incoming internal call.
Internal call in progress.
3-way call in progress or transfer an external call to another C1 handset
registered to the base.
Eco mode is ON.
Flashes to indicate new voicemail messages received. Off when you
have no voicemail messages.1
Indicates signal strength.
Flashes when handset is not registered to the base or if you go out
of range.
Menu is opened.
Phonebook is opened.
Flashes to indicate new calls list entries received.2
Answered call (when viewing the Calls list).2
Unanswered call (when viewing the Calls list).2
Keypad is locked.
Answering machine is ON.
Displayed number is longer than 12 digits.
The approximate power levels of your battery are indicated as follows:
Battery is fully charged.
Battery is partially charged.
Battery is running low.
Flashes when battery is almost fully discharged.

14
Getting to know your phone
1This feature is dependent on your Network Service provider supporting the
service. A subscription fee may be payable.
2For this feature to work, you must subscribe to Caller ID Service from your
network operator. A subscription fee may be payable.
Overview of the base
A
B
C
D
E
F
G
H
I
J
A LED
Indicates when the answer machine is on or off and when you have
messages.
Status Action
On Answer machine on
Off Answer machine off
Flashes New message (s)
B Volume Up
Adjust playback volume.
C Ans On / Off
Switches the answering machine on / off.
D Delete
Press to delete recorded messages during playback or press to announce
the current remote access code setting.
E Volume Down
Adjust playback volume.
F Page
In standby mode, press to ring the handset(s), page 20.
Press and hold to enter registration mode when registering handsets,
page 33.

15
Getting to know your phone
G Stop
Stops message playback.
Press to announce the current day and time setting.
H Skip forward
Press to skip forward or backward through your answering machine
messages.
Press to announce the current answer delay setting.
Press and hold to set the answer delay setting.
I Skip back
Press to skip backward through your answering machine messages.
Press to announce the current message alert setting.
Press and hold to turn message alert on / off.
J Play / Pause
Play or pause recorded messages.
Press to play new messages or press and hold to play all message.
Navigating the menus
Your C1 has an easy to use menu system.
Each menu has a list of options, which you can see on the menu map on the
following page.
When the handset is switched on and in standby:
1. Press to open the main menu.
2. Then use or buttons to scroll through the available options.
3. Press to select an option.To return to the previous menu level,
press .To exit the menu and return to standby, press .
NOTE
If no buttons are pressed for 20 seconds, the handset returns to standby
automatically.

16
Menu map
Menu map
PLAY MESSAGE
NEW MSG
ALL MSG
PHONEBOOK
ADD ENTRY
MODIFY ENTRY
DELETE ENTRY
TAM SETTINGS
ANS ON / OFF
ANS MODE
MEMO REC
OGM SETTING
DAY SETTING
ANS DELAY
REMOTE CODE
SETUP
BASE VOLUME
BASE MELODY
DEL HANDSET
PIN CODE
DIAL MODE
RECALL
DEFAULT
ECO MODE
HANDSET
BEEP
INT RING VOL
EXT RING VOL
INT MELODY
EXT MELODY
AUTO ANSWER
NAME
LANGUAGE
KEYLOCK ?
DATE --TIME
DATE SET
CLOCK SET
ALARM SET
REGISTER
SELECT BASE
REG BASE

17
Using the phone
3. Using the phone
NOTE
Your handset will automatically time the duration of all external calls.The call
timer will display after the rst 15 seconds of your call. When the call ends,
the total duration of your talk time is shown for 5 seconds.
3.1 Switch the handset on / off
Press and hold to switch the handset on or off.
3.2 Calls
3.2.1 Make a call
1. Press .
2. When you hear the dial tone, dial the number.
3.2.2 Preparatory dialling
1. Dial the number rst. If you make a mistake press to
delete the last digit.
2. Press to dial.
NOTE
To enter a pause (P) when pre-dialling, see page 21.
3.2.3 End a call
Press , or place the handset back on the base or charger.
3.2.4 Receive a call
When you receive an external call, the phone rings and icon ashes on
the display.
1. If the handset is off the base then press to answer the call, or if the
handset is on the base simply lift the handset to answer the call.
NOTE
If you prefer to press when you lift up the handset to answer a call, you
will need to switch Auto answer off, see page 23.
3.3 Adjust the earpiece volume
During a call, press or to increase or decrease the volume.There are 5
levels to choose from.

18
Using the phone
3.4 Mute
You can mute your handset so that you can talk to someone nearby without
your caller hearing.
1. During a call, press .The display shows
MUTE and your caller cannot
hear you.
2. Press again to resume your call.
3.5 Intercom
3.5.1 Make an internal call
If you have more than one handset registered to the base, you can make
internal calls between two handsets.
icon is displayed to indicate an internal call.
1. Press followed by the number (1-5) of the handset you want to call.
3.5.2 Receive an internal call
When you receive an internal call, icon ashes and the handset number
that is calling you is displayed.
1. Press to answer the call.
3.5.3 Transfer a call
You can transfer an external call to another handset registered to the base.
During an external call:
1. Press followed by the handset number (1-5) that you want to
transfer to.
2. When the other handset answers, press to complete the transfer.
NOTE
If there is no answer from the other handset and you wish to return
to your external caller, press .
Your external call resumes automatically after 30 seconds if there is
no answer.
3.5.4 3-way conference call
You can hold a 3-way conference call between 2 internal callers and 1
external caller.
During a call with an external caller:
1. Press followed by the handset number (1-5) that you want to
establish a conference call.
2. When the other handset answers, press to connect all three callers
to begin the conference call. icon is displayed.

19
Using the phone
3. If there is no answer from the other handset, press to return to your
external caller.
4. Press to end the call.
3.6 Redial
The last 10 entries dialled are stored in the redial list.
3.6.1 View or dial an entry
1. Press to open the Redial list.
2. Scroll or to the entry you want.
3. Press to dial the displayed entry or press to return to standby.
NOTE
If the caller’s number exactly matches an entry stored in the
phonebook, the name is displayed. Press to see the caller’s number.
3.6.2 Copy a Redial list number to the phonebook
1. Press to open the Redial list.
2. Scroll or to the entry you want.
3. Press . The display shows
ADD ? .
4. Press again.The display shows
NAME ? .
5. Enter the name and press .The number is displayed.
6. Edit the number if necessary, then press .
7. Press or to select the ringer melody you want and press .
The number is stored.
NOTE
See “ENTERING NAMES” and “WRITINGTIPS” on page 21.
3.6.3 Delete an entry
1. Press to open the Redial list.
2. Scroll or to the entry you want and press .The display
shows
DELETE ? .
3. Press to conrm or to cancel.
3.6.4 Delete the entire Redial list
1. Press to open the Redial list.
2. Press and hold . The display shows
DELETE ALL ? .
3. Press to conrm or to cancel.

20
Using the phone
3.7 Lock / unlock the keypad
You can lock the keypad so that it cannot be operated accidentally while
carrying it around.
NOTE
When the keypad is locked, you can still answer incoming calls and operate
the handset as normal. When the call ends, the keypad lock comes on again.
1. Press and hold .
icon is displayed.
2. To unlock the keypad, press any key on your handset.The display
shows
PRESS * .
3. Press within 5 seconds.
3.8 Paging / Find handset
You can alert a handset user that they are wanted or locate a
missing handset.
Paging calls cannot be answered by a handset.
1. Press on the base. All handsets registered to the base will ring.
2. To stop the ringing, press on the base again or press any button on
the handset.