Motorola MOTOwi4 Canopy 30 User manual

Canopy™30/60 Mbps
Backhaul
User Guide

BH30/60-UG-en
Issue 3.1
July 2006

Issue 3.1, July 2006 Page 2 of 162
Notices
See the following information:
◦important regulatory and legal notices in Section 15 on Page 150.
◦personal safety guidelines in Section 15.3.1 - Preventing Overexposure to RF
Energy on Page 154.

Trademarks,ProductNames,andServiceNames
MOTOROLA, the stylized M Logo and all other trademarks indicated as such herein are
trademarks of Motorola, Inc.®Reg. U.S. Pat & Tm. Office. Canopy is a trademark of Motorola,
Inc. All other product or service names are the property of their respective owners.
© 2005 Motorola, Inc. All rights reserved.
http://www.motorola.com/canopy
Canopy 30/60 Mbps Backhaul
Same Form Factor – 5.4 GHz and 5.7 GHz
Available in two versions:
Integrated Antenna & Connectorized1Antenna
1Connectorized antennas sold separately from radio.
See Section 13.7 for a complete list of single and dual pole flat panel (1’ – 2’) and parabolic antennas (2’ – 6’)

Issue 3.1, July 2006 Page 3 of 162
General Notice
Changes or modifications not expressly approved by Motorola could void the user’s authority to operate
the system.
The frequency band in which the system operates is ‘unlicensed’ and the system is allowed to be used
provided it does not cause interference. Further, it is not guaranteed protection against interference
from other products and installations.
The system has basically been shown to comply with the limits for emitted spurious radiation for a
Class B digital device1
FP pursuant to Part 15 of the FCC Rules in the USA as well as comparable
regulations in other countries. These limits have been designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the Outdoor Unit (ODU).
•Increase the separation between the equipment and ODU.
•Connect the equipment into a power outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Deployment and Operation
The Radio Regulations of various countries constrain the operation of radio products generally. In
particular, at 5.4 GHz and 5.7GHz, the local regulator may limit the amount of conducted or radiated
transmitter power; the frequency band used and may require registration of the radio link.
The power transmitted by the Canopy 30/60 Mbps Backhaul product is controlled by the use of Region-
specific License Keys.
The following examples show how the regulatory limits apply in some specific countries at the current
time. Operators should note that regulations are subject to change.
Contact your supplier/installer to ensure that the product has achieved Type Approval and is set to the
correct license key for your country/region and to ensure that you have fulfilled all local regulatory
requirements, especially if you are intending to use a link with external antennas. Footnotes to the
table below indicate countries where registration of the link is currently mandatory.
Disclaimer
The parameters quoted in this document must be specifically confirmed in writing before they become
applicable to any particular order or contract. The company reserves the right to make alterations or
TP
1
PT Class B Digital Device, A digital device that is marketed for use in a residential environment notwithstanding use in
commercial, business and industrial environments.

Issue 3.1, July 2006 Page 4 of 162
amendments to the detail specification at its discretion. The publication of information in this document
does not imply freedom from patent or other rights of Motorola or others.

Issue 3.1, July 2006 Page 5 of 162
TABLEOFCONTENTS
1.1 NEW TO THIS ISSUE.......................................................................................14
1.2 Interpreting Typeface and Other Conventions..................................................14
1.3 Getting Additional Help .....................................................................................16
1.4 Sending Feedback............................................................................................16
2Getting Started.......................................................................................................... 17
2.1 For Your Safety.................................................................................................17
3Product Description ................................................................................................. 18
3.1.1 The Outdoor Unit (ODU)...................................................................................19
3.1.2 The 30/60 Mbps Power Indoor Unit (PIDU) ......................................................20
3.1.3 PIDU AC Power.................................................................................................21
3.1.4 Redundancy and Alternate Powering Configurations.......................................22
3.1.5 Remote LEDs and Recovery Switch.................................................................23
3.1.6 Cables and Connectors.....................................................................................24
3.1.7 Surge Arrestor...................................................................................................24
3.1.8 Mounting Brackets.............................................................................................24
3.1.9 Configuration and Management........................................................................24
4Product Architecture................................................................................................ 25
5General Considerations........................................................................................... 27
5.1 Spectrum Planning............................................................................................27
5.2 Region Codes ...................................................................................................27
5.3 Operational Restrictions....................................................................................28
5.3.1 Radar Avoidance...............................................................................................28
5.3.2 RTTT Avoidance And Other Channel Use Restrictions....................................29
5.4 5.4 GHz Specific Frequency Planning Considerations .....................................29
5.4.1 Raster Considerations.......................................................................................30
5.4.2 Transmit Power Reduction at the Band Edges.................................................30
5.5 5.7GHz Specific Frequency Planning Considerations ......................................31
5.5.1 Raster Considerations.......................................................................................31
5.5.2 Transmit Power Reduction at the Band Edges.................................................31
5.6 Distance............................................................................................................ 31
5.7 Networking Information.....................................................................................32
5.8 Lightning Protection ..........................................................................................32

Issue 3.1, July 2006 Page 6 of 162
5.9 Electrical Requirements.................................................................................... 32
6Site Planning............................................................................................................. 33
6.1 Site Selection Criteria........................................................................................33
6.1.1 ODU Site Selection ...........................................................................................33
6.1.2 30/60 Mbps PIDU Site Selection.......................................................................33
6.1.3 Path Loss Considerations .................................................................................34
6.1.4 Aggregate Ethernet Throughput Rates v Maximum Link Loss .........................34
6.1.5 Rules for Collocating.........................................................................................35
6.1.6 Additional Information for Collocating ...............................................................36
7Installation................................................................................................................. 37
7.1 Preparation........................................................................................................37
7.2 Installation Procedure ....................................................................................... 37
7.3 Tools Required..................................................................................................37
7.4 Installation Support ........................................................................................... 37
7.5 Legal Disclaimer................................................................................................38
7.6 Mounting the ODUs...........................................................................................38
7.7 Connecting Up .................................................................................................. 39
7.7.1 Preparing the Cable — RJ45 connections........................................................39
7.7.2 Making the Connection At The ODU.................................................................41
7.7.3 Routing the Cable..............................................................................................42
7.7.4 Fitting a Surge Arrestor.....................................................................................42
7.7.5 Grounding the Installation.................................................................................42
7.7.6 Making the ODU Connection At The 30/60 Mbps PIDU...................................43
7.7.7 Making the Network Connection At The 30/60 Mbps PIDU..............................43
7.7.8 Mounting The 30/60 Mbps PIDU.......................................................................44
7.7.9 Powering Up......................................................................................................45
7.7.10 Aligning the ODUs.............................................................................................46
8Web Page Reference................................................................................................48
8.1 Home Page.......................................................................................................49
8.1.1 Home Page Alarm Display................................................................................49
8.2 Systems Status Page........................................................................................ 51
8.3 System Administration Pages...........................................................................56
8.3.1 System Configuration Page ..............................................................................56
8.3.2 LAN Configuration Page....................................................................................59
8.3.3 Save and Restore Menu....................................................................................61

Issue 3.1, July 2006 Page 7 of 162
8.3.4 Statistics Page...................................................................................................63
8.3.5 Detailed Counters..............................................................................................65
8.3.6 Install Wizard Pages..........................................................................................67
8.3.7 Manually Configuring The Wireless Units.........................................................68
8.3.8 Graphical Install.................................................................................................79
8.3.9 Software Upgrade .............................................................................................80
8.3.10 Spectrum Management.....................................................................................82
8.3.11 Spectrum Management (Fixed Frequency).......................................................91
8.3.12 Spectrum Management Control - With Operational Restrictions......................93
8.3.13 Remote Management Page ..............................................................................95
The Remote Management page allows the system administrator to configure the remote
management of the 30/60 Mbps Backhaul.....................................................................95
8.3.14 Diagnostics........................................................................................................98
8.3.15 Diagnostics Plotter ............................................................................................99
8.3.16 CSV Download................................................................................................100
8.3.17 Change System Administration Password......................................................101
8.3.18 License Key.....................................................................................................101
8.3.19 Properties........................................................................................................103
8.3.20 Reboot.............................................................................................................103
9Fault Finding........................................................................................................... 105
9.1 Hardware.........................................................................................................105
9.1.1 Power ..............................................................................................................105
9.1.2 Ethernet...........................................................................................................105
9.2 Radio...............................................................................................................108
9.2.1 No Activity .......................................................................................................108
9.2.2 Some Activity...................................................................................................108
10 Specifications.........................................................................................................109
10.1 System Specifications.....................................................................................109
10.1.1 Wireless 5.4 GHz Variant................................................................................109
10.1.2 Wireless 5.7 GHz Variant................................................................................111
10.1.3 Physical...........................................................................................................116
10.1.4 Powering .........................................................................................................116
10.2 Safety Compliance..........................................................................................116
10.2.1 5.4 GHz Variant...............................................................................................116
10.2.2 5.7 GHz Variant...............................................................................................116
10.3 EMC Emissions Compliance...........................................................................117

Issue 3.1, July 2006 Page 8 of 162
10.3.1 5.4 GHz Variant...............................................................................................117
10.3.2 5.7 GHz Variant...............................................................................................117
10.4 EMC Immunity Compliance.............................................................................117
10.5 Radio Certifications.........................................................................................118
10.5.1 5.4GHz Variant................................................................................................118
10.5.2 5.7GHz Variant................................................................................................118
10.6 Environmental Specifications..........................................................................118
10.7 System Connections.......................................................................................119
10.7.1 ODU to 30/60 Mbps PIDU Connection............................................................119
11 Lightning Protection .............................................................................................. 120
11.1 Overview.........................................................................................................120
11.1.1 Lightning Protection Zones .............................................................................120
11.2 Detailed Installation.........................................................................................120
11.3 Testing Your Installation.................................................................................. 129
11.3.1 Pre-Power Testing...........................................................................................129
11.3.2 Post-Power Testing.........................................................................................130
12 Wind Loading.......................................................................................................... 131
12.1 General ...........................................................................................................131
12.2 Calculation of Lateral Force............................................................................ 131
12.3 30/60 Mbps Backhaul Capabilities..................................................................132
12.4 Wind Speed Statistics.....................................................................................132
13 Connectorized 30/60 Mbps Backhaul ................................................................... 133
13.1 Scope..............................................................................................................133
13.2 Product Description.........................................................................................133
13.2.1 Hardware.........................................................................................................133
13.2.2 Antenna Choices.............................................................................................133
13.3 Software/Features...........................................................................................134
13.3.1 Status Page.....................................................................................................134
13.3.2 Configuration Pages........................................................................................135
13.3.3 Installation Pages............................................................................................136
13.4 Deployment Considerations............................................................................138
13.5 Link Budget..................................................................................................... 139
13.6 Regulatory Issues ...........................................................................................140
13.6.1 Antenna Choice...............................................................................................140
13.6.2 Cable Losses...................................................................................................140

Issue 3.1, July 2006 Page 9 of 162
13.7 Antennas for FCC Regions.............................................................................142
13.8 Installation.......................................................................................................143
13.8.1 Antenna Choice...............................................................................................143
13.8.2 Cables and Connectors...................................................................................144
13.8.3 Tools................................................................................................................144
13.8.4 Miscellaneous supplies ...................................................................................144
13.8.5 Mounting..........................................................................................................144
13.8.6 Alignment Process ..........................................................................................145
13.8.7 Completing the Installation..............................................................................145
14 FAQs........................................................................................................................ 148
15 Legal and Regulatory Notices...............................................................................150
15.1 Important Note on Modifications .....................................................................150
15.2 National and Regional Regulatory Notices .....................................................150
15.3 Exposure.........................................................................................................154
15.3.1 Preventing Overexposure to RF Energy.........................................................154
15.3.2 Calculations for Separation Distances and Power Compliance Margins........154
15.4 Legal Notices ..................................................................................................155
15.4.1 Software License Terms and Conditions ........................................................155
15.4.2 Hardware Warranty in U.S. .............................................................................157
15.4.3 Limit of Liability................................................................................................157
16 Additional Resources............................................................................................. 158
17 Glossary.................................................................................................................. 159
18 Appendix A: The 45 Mbps Backhaul Power Indoor Unit (PIDU)......................... 160
18.1.1 45 Mb BH PIDU AC Power..............................................................................161
18.1.2 Cables and Connectors...................................................................................161
18.1.3 Surge Arrestor.................................................................................................162

LISTOFFIGURES
Figure 1: Typical 30/60 Mbps Backhaul Deployment...............................................................18
Figure 2: 30/60 Mbps Backhaul Outdoor Unit (ODU)...............................................................19
Figure 3: 30/60 Mbps Power Indoor Unit (PIDU) .....................................................................20
Figure 4: 30/60 Mbps PIDU Reset Switch Location.................................................................20
Figure 5: 30/60 Mbps PIDU AC Power Input ...........................................................................22

Issue 3.1, July 2006 Page 10 of 162
Figure 6: External DC Supply Only..........................................................................................22
Figure 7: External DC Supply and AC Supply..........................................................................22
Figure 8: External DC Supply and Redundant AC Supply.......................................................23
Figure 9: Remote LED and Recovery Switch Wiring ...............................................................23
Figure 10: 30/60 Mbps Backhaul Layer Diagram.....................................................................25
Figure 11: 5.8 GHz UK RTTT Channel Avoidance ..................................................................29
Figure 12: 5.4 GHz Available Spectrum Settings....................................................................30
Figure 13: 5.7 GHz Available Spectrum Settings.....................................................................31
Figure 14: 5.7 GHz Band Edge TX Power Reduction (Region Code 1 Only)..........................31
Figure 15: Mounting to pole diameters 25mm (1") to 50mm (2").............................................38
Figure 16: Integral Safety Loop................................................................................................39
Figure 17: Completed ODU connector.....................................................................................40
Figure 18: RJ45 Pin Connection..............................................................................................41
Figure 19: Disconnecting the ODU ..........................................................................................42
Figure 20: Making the Network Connection at the 30/60 Mbps PIDU......................................44
Figure 21: 30/60 Mbps PIDU Drip Loop Configuration.............................................................45
Figure 22: Menu Navigation Bar ..............................................................................................48
Figure 23: 30/60 Mbps Backhaul Home Page ........................................................................49
Figure 24: Alarm Warning Triangle..........................................................................................50
Figure 25: Status Page ............................................................................................................52
Figure 26: System Administration Login Page.........................................................................56
Figure 27: Configuration Page.................................................................................................57
Figure 28: Configuration Reboot Page.....................................................................................59
Figure 29: LAN Configuration Page.........................................................................................59
Figure 30: VLAN Warning Window ..........................................................................................60
Figure 31: Additional VLAN Options ........................................................................................60
Figure 32: Save & Restore Window.........................................................................................61
Figure 33: config.Canopy file ...................................................................................................62
Figure 34: Restore Configuration Warning Message...............................................................62
Figure 35: System Statistics.....................................................................................................63
Figure 36: Detailed Counters...................................................................................................65
Figure 37: Installation Wizard Internet Protocol Configuration.................................................68
Figure 38: VLAN Warning........................................................................................................69
Figure 39: Installation Wizard Wireless Configuration .............................................................70
Figure 40: Fixed Frequency Operation – Page 1.....................................................................72

Issue 3.1, July 2006 Page 11 of 162
Figure 41: Fixed Frequency Operation – Page 2.....................................................................73
Figure 42: Installation Wizard Confirm Configuration - Normal................................................74
Figure 43: Installation Wizard Confirm Configuration – Fixed Frequency................................75
Figure 44: Installation Wizard Confirm Configuration - Connectorized....................................76
Figure 45: Disarm Installation ..................................................................................................77
Figure 46: Optional Post Disarm Configuration........................................................................78
Figure 47: Installation Screen ..................................................................................................79
Figure 48: Software Upgrade – Step 1.....................................................................................80
Figure 49: Software Upgrade Image Check.............................................................................81
Figure 50: Overall Progress Tracker........................................................................................81
Figure 51: Software Upgrade Complete...................................................................................82
Figure 52: Spectrum Management - Master ............................................................................84
Figure 53: Spectrum Management - Slave ..............................................................................85
Figure 54: Example Spectrum Management Graphic..............................................................87
Figure 55: Active Channel History Screen...............................................................................89
Figure 56: Spectrum Management Timeseries Plot.................................................................89
Figure 57: Spectrum Management Help Page.........................................................................91
Figure 58: Spectrum Management Fixed Frequency Screen – Master ...................................92
Figure 59: Spectrum Management Fixed Frequency Screen - Slave......................................93
Figure 60: Spectrum Management Master Screen With Operational Restrictions...................94
Figure 61: Spectrum Management Slave Screen With Operational Restrictions.....................94
Figure 62: Remote Management .............................................................................................96
Figure 63: Diagnostic Plotter....................................................................................................99
Figure 64: CSV Download......................................................................................................100
Figure 65: Password Change.................................................................................................101
Figure 66: Software License Key Data Entry.........................................................................102
Figure 67: License Key Reboot Screen .................................................................................103
Figure 68: Webpage Properties.............................................................................................103
Figure 69: System Reboot .....................................................................................................104
Figure 70: Main System Connections....................................................................................105
Figure 71: ODU to 30/60 Mbps PIDU Connection Diagram...................................................119
Figure 72: ODU mounted in Zones A & B..............................................................................121
Figure 73: Showing how the use of a Finial enables the ODU to be mounted inside Zone B
.........................................................................................................................................122
Figure 74: Diagrammatically showing typical wall and mast installations..............................123

Issue 3.1, July 2006 Page 12 of 162
Figure 75: Upper Grounding Configuration............................................................................124
Figure 76: Lower Grounding Configuration............................................................................125
Figure 77: Surge Arrestor ALPU-ORT Connection Illustration...............................................128
Figure 78: Simplified Circuit Diagram (Only One Transtector Shown For Clarity).................129
Figure 79: Connectorized 30/60 Mbps Backhaul Outdoor Unit..............................................133
Figure 80: Connectorized 30/60 Mbps Backhaul Status Page...............................................134
Figure 81: Connectorized 30/60 Mbps Backhaul ‘System Configuration’ Page.....................135
Figure 82: Connectorized 30/60 Mbps Backhaul ‘Installation Wizard’ Page..........................136
Figure 83: Connectorized 30/60 Mbps Backhaul ‘Confirm Installation’ Page ........................137
Figure 84: Connectorized 30/60 Mbps Backhaul ‘Disarm Installation’ Page..........................138
Figure 85: Forming a Drip Loop.............................................................................................146
Figure 86: Weatherproofing the Antenna Connections..........................................................147
Figure 87: 45 Mbps Backhaul Power Indoor Unit (PIDU).......................................................160
Figure 88: 45 Mbps Backhaul Reset Switch Location............................................................160
Figure 89: 45 Mb BH PIDU AC Power Input..........................................................................161

LISTOFTABLES
Table 1: Font types ..................................................................................................................14
Table 2: Admonition types........................................................................................................15
Table 3: Reset Actions.............................................................................................................21
Table 4: 30/60 Mbps Backhaul Region Code Definitions.........................................................28
Table 6: Audio indications from the ODU.................................................................................46
Table 7: 30/60 Mbps Backhaul Factory Configuration Values.................................................67
Table 8: Spectrum Management (Non UK) change state key..................................................88
Table 9: Spectrum Management timeseries key......................................................................90
Table 10: Spectrum Management Change State Key With Operational Restrictions..............95
Table 11: Protection Requirements........................................................................................123
Table 12: Surge Arrestor ALPU-ORT Cable 1 Termination...................................................127
Table 13: Surge Arrestor ALPU-ORT Cable 2 Termination...................................................127
Table 14: Resistance Table Referenced To The RJ45 At The PIDU.....................................130
Table 15: 5.4GHz Variant Link Budget for Various Antenna Options ....................................139
Table 16: 5.7 GHz Variant Link Budget for Various Antenna Options ...................................140
Table 17: Cable Losses per Length.......................................................................................141
Table 18: Allowed Antennas for Deployment in USA/Canada...............................................143

Issue 3.1, July 2006 Page 13 of 162
Table 19: US FCC IDs and Industry Canada certification numbers.......................................150
Table 20: Reset Actions.........................................................................................................161

Issue 3.1, July 2006 Page 14 of 162
AboutThisUserGuide
This guide covers the installation, commissioning, operation and fault finding of the Canopy
30/60 Mbps Backhaul system.
1.1 NEWTOTHISISSUE
•Introduction of a 5.4 GHz hardware variant. The new 5.4 GHz hardware variant operates
between a 5.470 to 5.725 GHz (defined as the ETSI 5 GHz band B).
•Packet Filtering default setting changed. Packet Filtering is required when a 30/60 Mbps
Backhaul link is bridging “non-switch-based” networks (i.e. the units are connected to
10/100bT HUBS) to prevent unnecessary traffic being bridged across the wireless link.
•Graphical installation tools – to aid the installation of wireless links two graphical
installation aids have been introduced.
•Enhanced Diagnostic Tools – the storage of link performance histograms has been
extended to 31 days of storage. Three levels of cascading histograms have been
introduced.
•Diagnostic Plotter allows the system administrator to view the cascading histogram data in
an easily accessible graphical form.
•CSV Download – The histogram data is made available as CSV files via the system
administration CSV download facility.
1.2 INTERPRETINGTYPEFACEANDOTHERCONVENTIONS
This document employs distinctive font to indicate the type of information, as described in Table
1.
Table 1: Font types
Font Type of Information
variable width bold Selectable option in a graphical user interface or settable
parameter in the web-based interface to a Canopy component.
constant width regular Literal system response in a command-line interface.
constant width italic Variable system response in a command-line interface.
constant width bold Literal user input in a command-line interface.
constant width bold italic Variable user input in a command-line interface.
This document employs specific imperative terminology as follows:
◦Type means press the following characters.
◦Enter means type the following characters and then press Enter.
◦Highlight means click anywhere in a row of data to highlight the entire row.
◦Select means use the mouse to click on or branch to the menu item that follows.

Issue 3.1, July 2006 Page 15 of 162
Use this table and the Glossary to aid in interpreting the technical acronyms used throughout
this User Guide.
30/60 BH Canopy 30/60 Mbps Backhaul Radio
30/60 PIDU Canopy 30/60 Mbps Power Indoor Unit (PIDU)
Mb Mbps
OFDM Orthogonal Frequency Division Multiplexing
LoS Line-of-Sight (Clear Line-of-Sight and Fresnel zone is clear)
nLoS near-Line-of-Sight (Clear Line-of-Sight, but Fresnel zone is blocked)
NLoS Non-Line-of-Sight (No Line-of-Sight and Fresnel zone is blocked)
ODU Outdoor Unit (Integrated or Connectorized Radio)
PIDU Powered Indoor Unit
DFS Dynamic Frequency Selection
PoE Power over Ethernet
This document also employs a set of consistently used admonitions. Each type of admonition has
a general purpose that underlies the specific information in the box. These purposes are indicated
in Table 2.
Table 2: Admonition types
Admonition
Label General Message
NOTE:
informative content that may
◦defy common or cursory logic.
◦describe a peculiarity of the Canopy implementation.
◦add a conditional caveat.
◦provide a reference.
◦explain the reason for a preceding statement or provide background
for what immediately follows.
RECOMMENDATION:
suggestion for an easier, quicker, or safer action or practice.
IMPORTANT:
informative content that may
◦identify an indication that you should watch for.
◦advise that your action can disturb something that you may not want
disturbed.
◦reiterate something that you presumably know but should always
keep in mind.
CAUTION!
a notice that the risk of harm to equipment or service exists.
WARNING!
a notice that the risk of harm to person exists.


Issue 3.1, July 2006 Page 16 of 162
1.3 GETTINGADDITIONALHELP
To get information or assistance as soon as possible for problems that you encounter, use the
following sequence of action:
Note: Search this document, the user manuals that support the modules, and the software
release notes of supported releases
a. in the Table of Contents for the topic.
b. in the Adobe Reader®search capability for keywords that apply.2
1. Visit the Canopy systems website at http://www.motorola.com/canopy.
2. Ask your Canopy products supplier to help.
3. Gather information such as
◦the IP addresses and MAC addresses of any affected Canopy modules.
◦the software releases that operate on these modules.
◦data from the Event Log page of the modules.
◦the configuration of software features on these modules.
4. Escalate the problem to Canopy systems Technical Support (or another Tier 3
technical support that has been designated for you) as follows. You may either
◦send e-mail to [e-mail].
◦call 1 888 605 2552 (or [phone]).
For warranty assistance, contact your reseller or distributor for the process.
1.4 SENDINGFEEDBACK
We welcome your feedback on Canopy system documentation. This includes feedback on the
structure, content, accuracy, or completeness of our documents, and any other comments you
have. Please send your comments to
[e-mail]
2Reader is a registered trademark of Adobe Systems, Incorporated.

Issue 3.1, July 2006 Page 17 of 162
2GettingStarted
2.1 FORYOURSAFETY
WARNING Use extreme care when installing antennas near power lines.
WARNING Use extreme care when working at heights.
WARNING The Canopy 30/60 Mbps Backhaul Outdoor unit (ODU) must be properly grounded
to protect against lightning. It is the user’s responsibility to install the equipment in accordance
with Section 810 of the National Electric Code, ANSI/NFPA No.70-1984 or Section 54 of the
Canadian Electrical Code. These codes describe correct installation procedures for grounding
the outdoor unit, mast, lead-in wire and discharge unit, size of grounding conductors and
connection requirements for grounding electrodes. It is recommended that installation of the
outdoor unit be contracted to a professional installer.
WARNING The Canopy 30/60 Mbps Backhaul ODU MUST be grounded to a Protective Earth
as described in Section 11 “Lightning Protection” of this Installation Manual and in accordance
with the Local Electrical Regulations.
WARNING It is recommended that the supplied 30/60 Mbps Backhaul Power Indoor Unit (30/60
Mbps PIDU) is used to power the 30/60 Mbps Backhaul ODU. The use of other power sources
may invalidate safety approval and affect your warrantee.
WARNING When using alternate DC supplies (via the Canopy 30/60 Mbps PIDU DC in
terminals as described in Section 3.1.4 “Redundancy and Alternate Powering Configurations”),
such as battery-backed DC power source, the supply MUST comply with the following
requirements:
•The voltage and polarity is correct and is applied to the correct terminals in the 30/60
Mbps PIDU
•The power source is rated as SELV
•The power source is rated to supply at least 1A continuously, and
•The power source cannot provide more than the Energy Hazard Limit as defined by
IEC/EN/UL6090, Clause 2.5, Limited Power (The Energy Hazard Limit is 240VA)
CAUTION When the system is operational, avoid standing directly in front of the antenna.
Strong RF fields are present when the transmitter is on. The Outdoor Unit must not
be deployed in a location where it is possible for people to stand or walk
inadvertently in front of the antenna.
CAUTION Users and installers should note that in an emergency the mains power supply is
the primary disconnect device.
CAUTION SAFETY will be compromised if external quality cables are not used for
connections that will be exposed to the weather.
CAUTION SAFETY will be compromised if a different power supply is used than the one
supplied by Motorola as part of the system. This will also invalidate your warranty.

Issue 3.1, July 2006 Page 18 of 162
3ProductDescription
This User Manual is specifically written for the Canopy 30/60 Mbps Backhaul and the 5X45
software load. The 30/60 Mbps Backhaul has been developed to provide Point-to-Point data
connectivity via the 5.4 GHz or 5.7 GHz wireless Ethernet bridge operating at broadband data
rates. The 30/60 Mbps Backhaul is aimed at enterprises that have a requirement to connect
together the Local Area Network (LAN) of two or more buildings. Figure 1 illustrates such a
deployment.
The 30/60 Mbps Backhaul offers true Non-Line-Of-Sight (NLOS) operation by using a
combination of Orthogonal Frequency Division Multiplex (OFDM) modulation and Transmit
Diversity techniques. These technologies enable the 30/60 Mbps Backhaul to drive through
foliage and around buildings to such an extent that almost universal coverage can be expected
at short range.
The 30/60 Mbps Backhaul consists of a pair of identical devices that are deployed one at each
end of the link. At install time the user sets up one unit as the Master and the other as the
Slave. Either unit can be configured as master or slave.
Each end of the link consists of:
•An integrated outdoor transceiver unit containing all the radio and networking electronics
hereafter referred to as the Outdoor Unit (ODU).
•An indoor connection box containing a mains power supply, status indicators and network
connection port. Hereafter referred to as the 30/60 Mbps Backhaul Indoor Unit (30/60
Mbps PIDU).
•Units will normally be supplied pre-configured as a link.
Figure 1: Typical 30/60 Mbps Backhaul Deployment
Power is fed into the 30/60 Mbps PIDU from the mains via a standard IEC mains plug. The
network connection is presented to the user at the 30/60 Mbps PIDU via an RJ45 socket.
Connection between the ODU and the 30/60 Mbps PIDU is made using standard shielded
CAT5 UV resistant cable. The spare twisted pairs of the cable are used to feed power from the
30/60 Mbps PIDU to the ODU.

Issue 3.1, July 2006 Page 19 of 162
3.1.1 TheOutdoorUnit(ODU)
The ODU (Figure 2) is a self-contained unit. It houses both radio and networking electronics. A
single CAT 5 cable feeds the unit. Power is fed to the unit via the brown/brown white pair
connected to pins 7 and 8 and the blue/blue white pair connected to pins 4 and 5 of the RJ45
plugs and sockets employed. It should be noted that this powering arrangement is not standard
Power Over Ethernet (POE). The 30/60 Mbps Backhaul ODU should only be deployed using
the supplied 30/60 Mbps Power Indoor Unit (PIDU).
WARNING: All four power conductors MUST be connected.
Important! The Canopy Cluster Management Module 2 CMM2) and Cluster Management
Module micro (CMMmicro) often used to power Canopy 20 Mb and 10 Mb Backhauls and
Access Points uses a different convention (different pins) for Power Over Ethernet than does
the 30/60 Mbps Backhaul. Do not connect the ODU directly to a CMM2 or CMMmicro. While
the lower voltage of the CMM2 or CMMmicro may not damage the ODU, the arrangement will
not work to power the 30/60 ODU.
The 30/60 Mbps Backhaul can be connected to the Ethernet switch in the CMM2 or the
CMMmicro, but through the 30/60 Mbps PIDU first. Connect the 30/60 ODU to the 30/60 Mbps
PIDU using (powered) Ethernet cable, and then connect the PIDU to the CMM using Ethernet
cable. For the CMM2, plug the cable into the Uplink Port. For the CMMmicro, plug the cable
into any unpowered port.
Figure 2: 30/60 Mbps Backhaul Outdoor Unit (ODU)

Issue 3.1, July 2006 Page 20 of 162
3.1.2 The30/60MbpsPowerIndoorUnit(PIDU)
The 30/60 Mbps PIDU is used to generate the ODU supply voltage from building AC (mains) supply.
The PIDU also houses a status indicator driven from the ODU.
WARNING! An external AC surge suppression device is recommended for use with the
Canopy 30/60 Mbps Backhaul. For infrastructure installations, Canopy Engineering
recommends an AC line surge suppression unit that meets the standard IEC 801-5 (EN6100-
4-5) Class 5 at +/- 6K volts on AC power source Line-Ground and +/- 4K volts on Line-Line.
Figure 3: 30/60 Mbps Power Indoor Unit (PIDU)
The front panel contains indicators showing the status of the power and Ethernet connections.
The power indicator is illuminated when the 30/60 Mbps PIDU is receiving AC (mains) power.
The Ethernet indicator normally illuminates when the Ethernet link is working; Flashing when
there is Ethernet activity; the fact that it lights also indicates that the ODU is powered. At power
up the LED will flash 10 times to indicate that a correct start up sequence has occurred. See
Section 9 for further fault finding information.
The bottom of the 30/60 Mbps PIDU houses the Ethernet connection via RJ-45 socket, an entry
point for 30/60 Mbps Backhaul PIDU/ODU cabling and the reset button.
Figure 4: 30/60 Mbps PIDU Reset Switch Location
The reset switch is used for various purposes identified in Table 3.