Motorola PMP 58430 User manual

PMP 400/430 Series Networks
PTP 200/230 Series Bridges
Issue 6
August 2011

Notices
See important safety notice on exposure distance in Section 6.3 on page 71.
See important regulatory and legal notices in Section 6on page 64.
Trademarks, Product Names, and Service Names
MOTOROLA SOLUTIONS, the stylized M Logo, Canopy, and all other trademarks indicated as
such herein are registered trademarks of Motorola, Inc. ® Reg. US Pat & Tm. Office. All other
product or service names are the property of their respective owners.
© 2011 Motorola Solutions, Inc. All rights reserved
http://www.motorola.com/canopy
http://motorola.wirelessbroadbandsupport.com

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 2 of 77
Table of Contents
1Introduction ...............................................................................................................6
1.1 Document Change History.................................................................................7
1.2 Abbreviations.....................................................................................................8
1.3 Feedback on Documentation.............................................................................9
1.4 Technical Support..............................................................................................9
2Product Description................................................................................................11
2.1 Technology and Benefits.................................................................................22
2.1.1 nLOS Benefits and Limitations..........................................................................22
2.2 Applications.....................................................................................................23
2.3 Configuration Options –RF, IP, DFS...............................................................24
2.4 Power and Grounding......................................................................................24
2.5 Administration Systems...................................................................................25
2.6 Specifications..................................................................................................26
2.6.1 Radio specifications (common to all formats) ...................................................26
2.6.2 Specifications for PMP 430 (5.4 & 5.8-GHz) SM and PTP 230 (5.4 & 5.8-GHz)
BH radio with integrated antenna ...................................................................................27
2.6.3 Specifications for PMP 400 (4.9 & 5.4-GHz) AP/SM and PTP 200 (4.9 & 5.4-
GHz) BH radio with integrated antenna..........................................................................28
2.6.4 Specification for PMP 400/430 AP and PTP 200 BH connectorized radio .......29
2.6.5 Specifications for PMP 400/430 kitted, connectorized radio (antenna included)29
2.7 Performance....................................................................................................31
3Configuring..............................................................................................................41
3.1 Link Operation –1X/2X/3X..............................................................................41
3.2 Transmitter Output Power (and no Jitter).........................................................42
3.3 Downlink Data %, Range, and Control Slots....................................................44
3.4 DFS and Regulatory Parameters for 5.8 & 5.4 GHz Radios.............................46
3.4.1 Background and Operation ...............................................................................46
3.4.2 Setting DFS and Regulatory Parameters..........................................................48
3.5 External Gain Field..........................................................................................52
3.6 Network Control Parameters ...........................................................................53
3.7 Forward Error Correction.................................................................................53
3.8 Cyclic Prefix (Configurable only on PTP 200/230 BH & PMP 430 AP/SM).......53
4Installation...............................................................................................................55
4.1 Installing an AP with Connectorized Antenna ..................................................55

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 3 of 77
4.2 Installing an SM or BH with an Integrated Antenna..........................................62
5Regulatory and Legal Notices ................................................................................64
5.1 Important Note on Modifications......................................................................64
5.2 National and Regional Regulatory Notices.......................................................64
5.2.1 U.S. Federal Communication Commission (FCC) Notification .........................64
5.2.2 Industry Canada (IC) Notification......................................................................67
5.2.3 Regulatory Requirements for CEPT Member States (www.cept.org)...............68
5.2.4 European Union Notification for 5.8 GHz Product ............................................69
5.2.5 Equipment Disposal ..........................................................................................69
5.2.6 EU Declaration of Conformity for RoHS Compliance........................................69
5.2.7 UK Notification...................................................................................................69
5.2.8 Luxembourg Notification....................................................................................69
5.2.9 Czech Republic Notification ..............................................................................70
5.2.10 Greece Notification............................................................................................70
5.2.11 Brazil Notification...............................................................................................70
5.2.12 Labeling and Disclosure Table for China..........................................................70
5.3 Exposure Separation Distances.......................................................................71
5.3.1 Details of Exposure Separation Distances Calculations and Power
Compliance Margins.......................................................................................................71
5.4 Legal Notices...................................................................................................73
5.4.1 Software License Terms and Conditions ..........................................................73
5.4.2 Hardware Warranty in US .................................................................................75
5.5 Limit of Liability................................................................................................75
List of Tables
Table 1: Motorola PMP 400/430 and PTP 200/230 Series.............................................12
Table 2: 5.8GHz OFDM - PMP 430 and PTP 230 Series Model Number Descriptions..12
Table 3: 5.4GHz OFDM - PMP 430 Series Model Number Descriptions........................14
Table 4: 5.4GHz OFDM - PMP 400 and PTP 200/230 Model Number Descriptions......15
Table 5: 4.9GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions.............16
Table 6: CMM4 56VDC and 30 VDC Operation.............................................................17
Table 7: Ancillary Equipment and Model Numbers........................................................20
Table 8: Performance Details........................................................................................32

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 4 of 77
Table 9: PMP 400/430 and PTP 200/230 Tx output power............................................42
Table 10: PMP 400/430 AP Control Slot Settings..........................................................45
Table 11: 5.4 / 5.8 GHz OFDM DFS Operation based on Region Code ........................47
Table 12: US FCC IDs and Industry Canada Certification Numbers and Covered
Configurations ........................................................................................................65
Table 13: Disclosure Table............................................................................................71
Table 14: Exposure Separation Distances.....................................................................71
Table 15: Calculated Exposure Distances and Power Compliance Margins..................72
List of Figures
Figure 1: PMP 430 CAP 54430 & 58430.........................................................................6
Figure 2: PMP 400 CAP 54400 - 5.4 GHz.......................................................................6
Figure 3: PMP 400 CAP 49400 - 4.9 GHz.......................................................................6
Figure 4: PMP 430 CSM 54430 & 58430.........................................................................6
Figure 5: PMP 400 CSM 54400 - 5.4GHz........................................................................6
Figure 6: PMP 400 CSM 49400 - 4.9 GHz.......................................................................6
Figure 7: PTP 200 Integrated..........................................................................................7
Figure 8: PTP 200 Connectorized ...................................................................................7
Figure 9: PTP 230 Integrated..........................................................................................7
Figure 10: CMM4 56 VDC Power Supply ......................................................................18
Figure 11: CMMmicro and CMM4 30 VDC Power Supply......................................18
Figure 12: CMM4 - 56 VDC and 30 VDC terminal blocks ..............................................18
Figure 13: 600SS Surge Suppression AP and SM diagram...........................................19
Figure 14: LOS, nLOS, and NLOS ................................................................................23
Figure 15: AP Grounding Lug........................................................................................25
Figure 16: 600SS pole mount kit ...................................................................................25
Figure 17: PMP 430 SM................................................................................................28
Figure 18: PMP 430 SM with Optional LENS ................................................................28
Figure 19: PMP 400 and PTP 200 radio with integrated antenna ..................................29
Figure 20: PMP 400/430 and PTP 200 BH connectorized radio....................................29
Figure 21: CAP 49400...................................................................................................30
Figure 22: CAP 58430 and 54430.................................................................................30
Figure 23: Dynamic Rate Adapt on AP "Configuration => General" page......................41
Figure 24: SM Power Level on AP “Home => Session Status” page. ............................44
Figure 25: Max Range & Downlink Data on AP "Configuration => Radio" page.............45

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 5 of 77
Figure 26: DFS Status on AP "Home => DFS Status" page. .........................................46
Figure 27: Region Code on AP “Configuration => General” page..................................50
Figure 28: Configured Region Code on SM Configuration => General page .................51
Figure 29: Active Region Code on SM Home => General Status page..........................51
Figure 30: Ground lug highlighted on AP.......................................................................61
Figure 31: Dielectric Grease –Apply to RJ45 connector ...............................................62
Figure 32: Dielectric Grease - Insert Ethernet Cable .....................................................63
List of Procedures
Procedure 1: Assembling a 5.8 or 5.4 GHz AP, and attaching to tower.........................56
Procedure 2: Assembling a 4.9 GHz AP, and attaching to tower...................................58
Procedure 3: Cabling and Grounding/Earthing the AP...................................................61

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 6 of 77
1Introduction
This guide provides product configuration information specific to the PMP 400/430 Series
networks and PTP 200/230 Series bridges in 5.8-GHz, 5.4-GHz and 4.9-GHz bands. Note: PMP
400 5.4-GHz Series is replaced with PMP 430 5.4-GHz Series.
PMP 430 Series
–5.4 & 5.8 GHz
Figure 1: PMP 430 CAP
54430 & 58430
PMP 400 Series
–5.4 GHz
Figure 2: PMP 400 CAP 54400
- 5.4 GHz
PMP 400 Series
–4.9 GHz
Figure 3: PMP 400 CAP
49400 - 4.9 GHz
Figure 4: PMP 430 CSM
54430 & 58430
Figure 5: PMP 400 CSM 54400
- 5.4GHz
Integrated and Connectorized
Figure 6: PMP 400 CSM
49400 - 4.9 GHz
Integrated and Connectorized

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 7 of 77
PTP 200 Series Backhauls –5.4 and 4.9 GHz
Figure 7: PTP 200
Integrated
PTP 54200 and 49200
Figure 8: PTP 200
Connectorized
PTP 54200 and 49200
PTP 230 Series Backhauls –5.4 and 5.8 GHz
Figure 9: PTP 230
Integrated
PTP 54230 and 58230
This guide should be used along with the Motorola PMP Solutions User Guide, which covers
general information, including all network features, RF control features, and GUI (Graphical User
Interface) features common across PMP 100, 400, and 500 Series networks and PTP 100 and
200 Series bridges. The Motorola PMP Solutions User Guide is available from the “User Guides”
section of the Canopy Document Library,
http://motorola.motowi4solutions.com/support/library/?region=1&cat=8.
This guide assumes that the reader has general RF (Radio Frequency) and Internet Protocol (IP)
knowledge and background.
This issue, Issue 6, is consistent with features provided by Canopy Release 11.0.1 (and
consistent with features provided by PTP 230 Canopy Release 10.7). Separate Release Notes for
each release are available and include open issues and other important information specific to
each release.
R11.0.1 and R10.7 Software and software release notes can be downloaded from the Motorola
support web site: http://motorola.wirelessbroadbandsupport.com/software/.
1.1 DOCUMENT CHANGE HISTORY
Issue 1
First Issue
Issue 2
Added the following:
PTP 200 Series –5.4-GHz BHs
PMP 400 and PTP 200 –Products using AES encryption

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 8 of 77
Software Release 8.4.3 features
Issue 3
Added the following 4.9-GHz public safety band products:
PTP 200 Series –4.9-GHz BHs
PMP 400 Series –4.9-GHz APs and SMs
Software Release 9.4.2 features
Issue 4
Added the following:
Software Release 9.5 features to support PMP 400 and PTP 200
PMP 430 Series –5.8-GHz APs and SMs
Software Release 10.0 features to support PMP 430 (10MHz channel)
Updated customer support email and phone numbers
Issue 5
Added the following:
PMP 430 Series 5.4-GHz AP and SM
PMP 430 Series (5.4 and 5.8-GHz OFDM) with Release 10.3
oConfigurable 5, 10 and 20 MHz channel bandwidth
Note: PMP 400 Series 5.4-GHz OFDM supports 10MHz channels.
o2.5MHz center channels when configured for 5MHz channel bandwidth
oAdded support for 1/16 Cyclic Prefix in addition to 1/4 and 1/8
Note: PMP 400 Series 5.4-GHz OFDM supports 1/4 Cyclic Prefix
oIncreased Packets Per Second (PPS) from 6,800 to 15,000 PPS
o802.1ad Q-in-Q DVLAN (Double VLAN) tagging
oDynamic Rate Adapt –configurable (1X, 2X, 3X) uplink/downlink rate
PMP 400 and PTP 200 Series with Release 10.3
o802.1ad Q-in-Q DVLAN (Double VLAN) tagging
oDynamic Rate Adapt –configurable(1X, 2X, 3X) uplink/downlink rate
Issue 6
Added the following:
PTP 230 Series 5.4 and 5.8-GHz BHM and BHS
1.2 ABBREVIATIONS
The following abbreviations may be used in these notes:
1X
1X (QPSK) modulation
2X
2X (16 QAM) modulation
3X
3X (64 QAM) modulation
AES
AP
Advanced Encryption Standard
Access Point Module
BH
Backhaul Module, either timing master or timing slave
BHM
Backhaul Module –Master
BHS
CAP
CIR
Backhaul Module –Slave
Access Point Module
Committed Information Rate
CMM
Cluster Management Module (CMM4 or CMMicro)
CNUT
CSM
Canopy Network Updater Tool
Subscriber Module
DES
DFS
Data Encryption Standard
Dynamic Frequency Selection for radar avoidance

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 9 of 77
DHCP
DiffServ
Dynamic Host Configuration Protocol
Differentiated Services
EIRP
Equivalent Isotropically Radiated Power
ETSI
European Telecommunications Standards Institute
EU
FCC
FSK
GHz
GPS
European Union
Federal Communications Commission (United States)
Frequency Shift Keying
Gigahertz
Global Positioning System
Note: CMM uses GPS to synchronize APs & BHs
LoS
MIB
MIR
NAT
Line of Sight
Management Information Base for SNMP
Maximum Information Rate
Network Address Translation
nLoS
NLoS
OFDM
Near Line of Sight
Non Line of Sight
Orthogonal Frequency Division Multiplexing
PMP
PPS
PTP
Point-to-Multi-Point (AP to SMs)
Packet Per Second
Point-to-Point (Backhauls)
QAM
Quadrature Amplitude Modulation
QPSK
Quadrature Phase Shift Keying
RF
Radio Frequency
SM
VDC
VLAN
Subscriber Module
Volts Direct Current
Virtual Local Area Network
1.3 FEEDBACK ON DOCUMENTATION
Is this document accurate, complete, and clear? How can it be improved? Please send your
feedback on Canopy documentation to technical-docum[email protected].
1.4 TECHNICAL SUPPORT
Tip! Do not clear the Event Log after you encounter issues. It may be useful to
Technical Support, if you need to escalate the issue.
Here is the escalation path for resolution of a problem:
1. Check documentation:
this document
Canopy System Release 8 Users Guide, available at
http://motorola.wirelessbroadbandsupport.com/software.
2. Consider checking the Community Forum and Knowledge Base at
http://motorola.wirelessbroadbandsupport.com/support/community.
3. Escalate the problem to your Canopy supplier or reseller.
4. Escalate the problem to Canopy Technical Support or other designated Tier 3
technical support:

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 10 of 77
U.S. and Canada Email: [e-mail]
1-866-961-9288
Latin and Central America Email: [e-mail]
Argentina 0800-666-2789
Brazil 0800-891-4360
Columbia 01-800-912-0557
Mexico 001-800-942-7721
Peru 0800-70-086
All other countries [phone]
Europe, Middle East, Email: [e-mail]
and Africa Denmark 043682114
France 0157323434
Germany 06950070204
Italy 0291483230
Lithuania 880 030 828
Netherlands 0202061404
Norway 24159815
Portugal 0217616160
Spain 0912754787
Russia 810 800 228 41044
Saudi Arabia 800 844 5345
South Africa 0800981900
United Kingdom 0203 0277499
Asia Pacific Email: [e-mail]
[phone] (9am - 5pm Malaysia Time)
[phone] (outside hours)
When you send e-mail or call, please include, as appropriate, software release on each module,
IP addresses, MAC addresses, and features enabled, like NAT, VLAN, high priority channel, or
CIR. You may be asked to run the Support Tool on CNUT or Prizm to provide a complete network
picture.

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 11 of 77
2Product Description
PMP 400/430 Series networks and PTP 200/230 Series bridges add OFDM-based (Orthogonal
Frequency Division Multiplexing) products to the Canopy family.
PMP 430 5.4 and 5.8-GHz SMs as shown in Figure 4 on page 6use the Canopy SM form
factor with an integrated antenna.
PMP 400 5.4-GHz SMs as shown in Figure 5 on page 6 are available with either an
integrated antenna or an external N-type connector on a short length of coaxial cable for
connecting to a connectorized antenna.
PMP 400 5.4-GHz AP and PMP 430 5.4 and 5.8-GHz APs as shown on page 6 are
always connectorized, and sold either as a radio with a connectorized antenna as a kit, or
as a radio with an external N-type connector on a short length of coaxial cable for
connecting to an operator-provided antenna. U.S. customers must use the kit version
since the FCC requires the radio to be regulatory certified with the connectorized
antenna.
PTP 200 5.4 and 4.9-GHz BHs as shown in Figure 7 and Figure 8 on page 7are
available with either an integrated antenna or an external N-type connector on a short
length of coaxial cable for connecting to a connectorized antenna.
PTP 230 5.4 and 5.8-GHz BHs as shown in Figure 9 on page 7 use the Canopy SM form
factor with an integrated antenna.
PMP 400/430 Series networks are available in multiple bands:
PMP 58430 APs and SM provide connectivity in the unlicensed 5.8 GHz band.
PMP 54430 APs and SMs provide connectivity in the unlicensed 5.4 GHz band.
PMP 54400 APs and SMs provide connectivity in the unlicensed 5.4 GHz band.
PMP 49400 APs and SMs provide connectivity in the licensed 4.9 GHz band allocated to
public safety services. State and local governmental entities are eligible to hold 4.9 GHz
licenses.
PTP 200/230 Series networks are available in multiple bands:
PTP 54200 BHs provide connectivity in the unlicensed 5.4 GHz band.
PTP 49200 BHs provide connectivity in the licensed 4.9 GHz band allocated to public
safety services. State and local governmental entities are eligible to hold 4.9 GHz
licenses.
PTP 54230 BHs provide connectivity in the unlicensed 5.4 GHz band.
PTP 58230 BHs provide connectivity in the unlicensed 5.8 GHz band.

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 12 of 77
Table 1 shows the Motorola PMP 400/430 Series and PTP 200/230 Series of products by
frequency band, channel bandwidth, cyclic prefix and current software version.
Table 1: Motorola PMP 400/430 and PTP 200/230 Series
Frequency
PMP Series
(Point-to-
MultiPoint)
PTP Series
(Point-To-Point)
Channel Bandwidth
Cyclic
Prefix
Software Version
PMP
Series
PTP
Series
PMP
Series
PTP
Series
5.8 GHz
PMP 430
Series -
58430
PTP 230 Series
-58230
5, 10 or
20MHz
10 or
20MHz
1/4, 1/8
or 1/16
11.0.1
10.7
5.4 GHz
PMP 430
Series -
54430
PTP 230 Series
-54230
5, 10 or
20MHz
10 or
20MHz
1/4, 1/8
or 1/16
11.0.1
10.7
5.4 GHz
PMP 400
Series
- 54400
PTP 200 Series
- 54200
10MHz
10MHz
1/4
11.0.1
11.0.1
4.9 GHz
PMP 400
Series -
49400
PTP 200 Series
- 49200
10MHz
10MHz
1/4
11.0.1
11.0.1
Table 2 shows the Motorola PMP 430 Series (5.8 GHz OFDM) AP and SM models.
Table 2: 5.8GHz OFDM - PMP 430 and PTP 230 Series Model Number Descriptions
CSM 58430
Model
Number
5.8GHz OFDM Subscriber
Module (SM) Description
Encryption
Picture
Power 29.5
VDC
Supply Type
Specs
in
Section
5790SM4
5.8 GHz OFDM SM –4 Mbps
DES
Refer to Table 7
for Models
2.6.2
5791SM4
5.8 GHz OFDM SM –4 Mbps
AES
2.6.2
5790SM10
5.8 GHz OFDM SM –10 Mbps
DES
2.6.2
5791SM10
5.8 GHz OFDM SM –10 Mbps
AES
2.6.2
5790SM20
5.8 GHz OFDM SM –20 Mbps
DES
2.6.2
5791SM20
5.8 GHz OFDM SM –20 Mbps
AES
2.6.2
5790SM40
5.8 GHz OFDM SM –Uncapped
DES
2.6.2
5791SM40
5.8 GHz OFDM SM –Uncapped
AES
2.6.2

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 13 of 77
CAP 58430
Model
Number
5.8GHz OFDM Access Point
(AP) Description
Encryption
Picture
CMM Type
Specs
in
Section
5780AP
5.8 GHz OFDM Connectorized
AP w/antenna
DES
Requires CMM4
w/56 VDC
supply
2.6.5
5780APUS
5.8 GHz OFDM Connectorized
AP w/antenna - US Model
DES
Requires CMM4
w/56 VDC
supply
2.6.5
5781AP
5.8 GHz OFDM Connectorized
AP w/antenna
AES
Requires CMM4
w/56 VDC
supply
2.6.5
5781APUS
5.8 GHz OFDM Connectorized
AP w/antenna - US Model
AES
Requires CMM4
w/56 VDC
supply
2.6.5
5780APC
5.8 GHz OFDM Connectorized
AP –No antenna
DES
Requires CMM4
w/56 VDC
supply
2.6.4
5781APC
5.8 GHz OFDM Connectorized
AP - No antenna
AES
Requires CMM4
w/56 VDC
supply
2.6.4
PTP 58230
Model
Number
5.8GHz OFDM Backhaul (BH)
Description
Encryption
Picture
CMM Type
Specs
in
Section
5780BH10
5.8 GHz OFDM BH –10 Mbps
DES
Requires CMM4
w/56 VDC
supply
2.6.6
5780BH20
5.8 GHz OFDM BH –20 Mbps
DES
Requires CMM4
w/56 VDC
supply
2.6.6
5780BH50
5.8 GHz OFDM BH –
Uncapped
DES
Requires CMM4
w/56 VDC
supply
2.6.6
5781BH10
5.8 GHz OFDM BH –10 Mbps
AES
Requires CMM4
w/56 VDC
supply
2.6.6
5781BH20
5.8 GHz OFDM BH –20 Mbps
AES
Requires CMM4
w/56 VDC
supply
2.6.6
5781BH50
5.8 GHz OFDM BH –
Uncapped
AES
Requires CMM4
w/56 VDC
supply
2.6.6

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 14 of 77
Table 3 shows the Motorola PMP 430 Series (5.4 GHz OFDM) AP and SM models.
Table 3: 5.4GHz OFDM - PMP 430 Series Model Number Descriptions
CSM 54430
Model
Number
5.4GHz OFDM Subscriber
Module (SM) Description
Encryption
Picture
Power 29.5
VDC
Supply Type
Specs
in
Section
5490SM4
5.4 GHz OFDM SM –4 Mbps
DES
Refer to Table 7
for Models
2.6.2
5491SM4
5.4 GHz OFDM SM –4 Mbps
AES
2.6.2
5490SM10
5.4 GHz OFDM SM –10 Mbps
DES
2.6.2
5491SM10
5.4 GHz OFDM SM –10 Mbps
AES
2.6.2
5490SM20
5.4 GHz OFDM SM –20 Mbps
DES
2.6.2
5491SM20
5.4 GHz OFDM SM –20 Mbps
AES
2.6.2
5490SM40
5.4 GHz OFDM SM –Uncapped
DES
2.6.2
5491SM40
5.4 GHz OFDM SM –Uncapped
AES
2.6.2
CAP 54430
Model
Number
5.4GHz OFDM Access Point
(AP) Description
Encryption
Picture
CMM Type
Specs
in
Section
5480AP
5.4 GHz OFDM Connectorized
AP w/antenna
DES
Requires CMM4
w/56 VDC
supply
2.6.5
5480APUS*
5.4 GHz OFDM Connectorized
AP w/antenna - US Model
DES
Requires CMM4
w/56 VDC
supply
2.6.5
5481AP
5.4 GHz OFDM Connectorized
AP w/antenna
AES
Requires CMM4
w/56 VDC
supply
2.6.5
5481APUS*
5.4 GHz OFDM Connectorized
AP w/antenna - US Model
AES
Requires CMM4
w/56 VDC
supply
2.6.5
5480APC
5.4 GHz OFDM Connectorized
AP –No antenna
DES
Requires CMM4
w/56 VDC
supply
2.6.4
5481APC
5.4 GHz OFDM Connectorized
AP - No antenna
AES
Requires CMM4
w/56 VDC
supply
2.6.4

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 15 of 77
Table 4 shows the Motorola PMP 400 and PTP 200/230 Series (5.4 GHz OFDM) models
available.
Table 4: 5.4GHz OFDM - PMP 400 and PTP 200/230 Model Number Descriptions
CSM 54400
Model
Number
5.4 GHz OFDM Subscriber
Module (SM) Description
DES
or
AES
Picture
Power 29.5 VDC
Supply Type
Specs
in
Section
5440SM
5.4 GHz OFDM SM
DES
Refer to Table 7
for Models
2.6.3
5441SM
5.4 GHz OFDM SM
AES
2.6.3
5440SMC
5.4 GHz OFDM Connectorized SM
DES
2.6.4
5441SMC
5.4 GHz OFDM Connectorized SM
AES
2.6.4
CAP 54400
Model
Number
5.4 GHz OFDM Access Point (AP)
Description
DES
or
AES
Picture
CMM Type
Specs
in
Section
5440AP
5.4 GHz OFDM Connectorized AP
w/antenna
DES
CMMmicro or CMM4
2.6.5
5440APUS
5.4 GHz OFDM Connectorized AP
w/antenna - US Model
DES
CMMmicro or CMM4
2.6.5
5441AP
5.4 GHz OFDM Connectorized AP
w/antenna
AES
CMMmicro or CMM4
2.6.5
5441APUS
5.4 GHz OFDM Connectorized AP
w/antenna - US Model
AES
CMMmicro or CMM4
2.6.5
5440APC
5.4 GHz OFDM Connectorized AP
–No Antenna
DES
CMMmicro or CMM4
2.6.4
5441APC
5.4 GHz OFDM Connectorized AP
–No Antenna
AES
CMMmicro or CMM4
2.6.4
PTP 54200
Model
Number
5.4 GHz OFDM Backhaul (BH)
Description
DES
or
AES
Picture
CMM Type
Specs
in
Section
5440BH
5.4 GHz OFDM BH
DES
CMMmicro or CMM4
2.6.3
5440BHUS
5.4 GHz OFDM BH –US Model
DES
CMMmicro or CMM4
2.6.3
5441BH
5.4 GHz OFDM BH
AES
CMMmicro or CMM4
2.6.3
5441BHUS
5.4 GHz OFDM BH –US Model
AES
CMMmicro or CMM4
2.6.3
5440BHC
5.4 GHz OFDM Connectorized BH
DES
CMMmicro or CMM4
2.6.4
5440BHCUS
5.4 GHz OFDM Connectorized BH
–US Model
DES
CMMmicro or CMM4
2.6.4
5441BHC
5.4 GHz OFDM Connectorized BH
AES
CMMmicro or CMM4
2.6.4
5441BHCUS
5.4 GHz OFDM Connectorized BH
–US Model
AES
CMMmicro or CMM4
2.6.4

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 16 of 77
PTP 54230
Model
Number
5.4 GHz OFDM Backhaul (BH)
Description
DES
or
AES
Picture
CMM Type
Specs
in
Section
5480BH10
5.4 GHz OFDM BH –10 Mbps
DES
Requires CMM4
w/56 VDC supply
2.6.6
5480BH20
5.4 GHz OFDM BH –20 Mbps
DES
Requires CMM4
w/56 VDC supply
2.6.6
5480BH50
5.4 GHz OFDM BH –Uncapped
DES
Requires CMM4
w/56 VDC supply
2.6.6
5481BH10
5.4 GHz OFDM BH –10 Mbps
AES
Requires CMM4
w/56 VDC supply
2.6.6
5481BH20
5.4 GHz OFDM BH –20 Mbps
AES
Requires CMM4
w/56 VDC supply
2.6.6
5481BH50
5.4 GHz OFDM BH –Uncapped
AES
Requires 56 VDC
supply
2.6.6
Table 5 shows the Motorola PMP 400 and PTP 200 Series (4.9 GHz OFDM) AP, SM and BH
models.
Table 5: 4.9GHz OFDM - PMP 400 and PTP 200 Model Number Descriptions
CSM 49400
Model
Number
4.9 GHz OFDM Subscriber
Module (SM) Description
Encryption
Picture
Power 56 VDC
Supply Type
Specs
in
Section
4940SM
4.9 GHz OFDM SM
DES
Refer to Table 7
for Models
2.6.3
4941SM
4.9 GHz OFDM SM
AES
2.6.3
4940SMC
4.9 GHz OFDM Connectorized
SM
DES
2.6.4
4941SMC
4.9 GHz OFDM Connectorized
SM
AES
2.6.4
CAP 49400
Model
Number
4.9 GHz OFDM Access Point
(AP) Module Description
Encryption
Picture
Power 56 VDC
CMM Type
Specs
in
Section
4940AP
4.9 GHz OFDM Connectorized
AP w/antenna
DES
Requires CMM4
w/56 VDC supply
2.6.5
4941AP
4.9 GHz OFDM Connectorized
AP w/antenna
AES
Requires CMM4
w/56 VDC supply
2.6.5

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 17 of 77
4940APC
4.9 GHz OFDM Connectorized
AP –No antenna
DES
Requires CMM4
w/56 VDC supply
2.6.4
4941APC
4.9 GHz OFDM Connectorized
AP –No antenna
AES
Requires CMM4
w/56 VDC supply
2.6.4
PTP 49200
Model
Number
4.9 GHz OFDM Backhaul (BH)
Description
Encryption
Picture
Power 56 VDC
CMM Type
Specs
in
Section
4940BH
4.9 GHz OFDM BH
DES
Wall type 56VDC
supply or CMM4
w/56 VDC supply
2.6.3
4941BH
4.9 GHz OFDM BH
AES
Wall type 56VDC
supply or CMM4
w/56 VDC supply
2.6.3
4940BHC
4.9 GHz OFDM Connectorized
BH –No antenna
DES
Wall type 56VDC
supply or CMM4
w/56 VDC supply
2.6.4
4941BHC
4.9 GHz OFDM Connectorized
BH –No antenna
AES
Wall type 56VDC
supply or CMM4
w/56 VDC supply
2.6.4
A Cluster Management Module (CMM4) provides GPS synchronization and power to the PMP
400/430 and PTP 200/230 series of products: Table 6 details the power requirements of the APs
and BHs.
Table 6: CMM4 56VDC and 30 VDC Operation
Frequency
PMP Series
Access Point (AP)
PTP 230 Series
Backhaul (BH)
Canopy Custom
Power over Ethernet (PoE)
5.8 GHz
5.4 GHz
PMP 430 Series –
CAP 58430/54430
PTP 230 Series –
PTP 58230/54230
56 VDC - Power on pins 5 &
8, return on pins 4 & 7
5.4 GHz
PMP 400 Series –
CAP 54400
PTP 200 Series –
PTP 54200
30 VDC - power on pins 7
and 8 and return on pins 4
and 5
4.9 GHz
PMP 400 Series –
CAP 49400
PTP 200 Series –
PTP 49200
56 VDC - Power on pins 5 &
8, return on pins 4 & 7
The CMM4 can be configured with either or both a 56VDC and a 30VDC external power supply
as shown in Figure 10 and Figure 11. The CMM4 must be used for 56 VDC operations which are
required for the PMP 430 5.4 and 5.8-GHz AP, PMP 400 4.9-GHz AP, PTP 200 4.9-GHz BH, and
PTP 230 5.4 and 5.8-GHz BH. The CMMmicro only supports 30 VDC operations.

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 18 of 77
Figure 10: CMM4 56 VDC Power Supply
Figure 11: CMMmicro and CMM4
30 VDC Power Supply
Shown in Figure 12 is a CMM4 with labels for the various parts. When using both a 56 VDC and
30 VDC power supply, it is necessary to install a resistor in the 30 VDC terminal blocks. Refer to
instructions included with the CMM4.
For details on configuring the CMM4, refer to the CMM4 User Guide which is available from the
Motorola support web site. http://motorola.wirelessbroadbandsupport.com/software/
Figure 12: CMM4 - 56 VDC and 30 VDC terminal blocks
A Cluster Management Module (CMMmicro) provides GPS synchronization and 30 VDC power to
the:
5.4-GHz PMP 400 Series - CAP 54400 uses 30 VDC
5.4-GHz PTP 200 Series - PTP 54200 uses 30 VDC
A 600SSD surge suppressor provides over-voltage and over-current protection to APs, SMs, and
BHs in various configurations. The diagram in Figure 13 illustrates the use of the 600SS surge
suppressor with the PMP 400/430 AP and SM.

PMP 400/430 and PTP 200/230 Series Motorola PMP Solutions User Guide Supplement
Issue 6.0 May 2011 Page 19 of 77
Figure 13: 600SS Surge Suppression AP and SM diagram