Motorola RMU2040 User manual

QUICK REFERENCE
GUIDE FOR
RADIO FEATURES
RM SERIES
BUILT TOUGH
TO DO
BUSINESS
BETTER
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license.
All other trademarks are the property of their respective owners. © 2013 Motorola Solutions, Inc. All rights reserved. Specifications are subject to change without notice. All specifications
shown are typical.

RM Series
Select your model by
clicking over the image
RMU2040 RMU2043 RMU2050RMU2080 RMU2080d RMV2080

RMU2040
QUICK REFERENCE GUIDE
1. DEFAULT VALUES
2. MODEL FEATURES
3. FACTORY DEFAULT
4. DISABLE TONES
5. IVOX
6. VOX
7. CHANNEL ANNOUNCEMENT
8. POWER UP AUDIO
9. ADVANCED CONFIGURATION
RMU2040

Power Up Audio:
Battery level +
Channel
PTT (Push-to-Talk)
Button
SB1 – Monitor Button
SB2 – Channel Down
RMU2040
DEFAULT VALUES
Channel Voice Prompt: On
Active Channels: 2
Battery Save: On
CHAN FREQ CODE
1 2 - 464.5500 1 – 67.0 Hz
2 8 - 467.9250 1 – 67.0 Hz
3* 5 - 467.8500 1 – 67.0 Hz
4* 6 - 467.8750 1 – 67.0 Hz
*When channels are enabled

Rugged Speaker Grill
Microphone
Antenna
On/Off Volume Knob
LED Indicator
Accessory
Connector
Lithium Ion
Battery
PTT (Push-to-Talk)
Button
SB1 – Monitor Button
SB2 – Channel Select
RM SERIES
NON-DISPLAY RADIO FEATURES
Applies to
RMU2040 / RMU2043 / RMM2050

PTT (Push-to-Talk)
Button
SB1 – Monitor Button
SB2 – Channel Select
RM SERIES
Factory Settings Reset
On/Off
Volume Knob
To reset radio to
Factory default
settings, Power up
with SB1, SB2 &
PTT pressed at the
same time.
Please note that all
channels will revert to
default frequencies.
Applies to
RMU2040 / RMU2043 / RMM2050

On/Off
Volume Knob
SB2 – Channel Select
RM SERIES
Toggle (Disable/Enable) Keypad tones
To disable/enable
keypad tones,
power up with SB2
button pressed
Applies to
RMU2040 / RMU2043 / RMM2050

On/Off
Volume Knob
PTT (Push-to-Talk)
Button
RM SERIES
IVOX hands free
To enable the IVOX
Power up with PTT
pressed .
Applies to
RMU2040 / RMU2043 / RMM2050

3) On/Off
Volume Knob
2)Attach
VOX
accessory
RM SERIES
External VOX hands free
Applies to
RMU2040 / RMU2043 / RMM2050
To enable voice activated
(VOX) accessories,
1. Use the Customer
Programming Software
(CPS) to change the Vox
Level of the radio
2. Attach a VOX supported
accessory
3. Power up with VOX
accessory attached

SB1 – Monitor Button
RM SERIES
Channel Voice Annunciation
To enable/disable the Channel
Voice announcement, power
up pressing SB1 button
On/Off
Volume Knob
Applies to
RMU2040 / RMU2043 / RMM2050

On/Off
Volume Knob
SB1 – Monitor Button
SB2 – Channel Select
RM SERIES
Power upAudioAnnouncement
To cycle through the Power
up Audio Announcement
options power the radio while
pressing SB1 + SB2 at the
same time.
OPTIONS:
1. Battery level + Channel #
2. Channel #
3. Silent
Applies to
RMU2040 / RMU2043 / RMM2050

PTT (Push-to-Talk)
Button
SB1 – Monitor Button
RM SERIES
Advanced Configuration
To enter the
Advanced
Configuration menu,
power up pressing
PTT + SB1 button
On/Off
Volume Knob
Applies to
RMU2040 / RMU2043 / RMM2050

RM SERIES
Advanced Configuration
1) The radio
provides voice
feedback of the
mode entered
Frequency
Code
Auto Scan
Active
Channel
PTT (Push-to-Talk)
Button
2) Press PTT to
cycle through the
Advanced
Configuration
Menu options
“Programming
Mode,
Channel 1”
CH 1
Applies to
RMU2040 / RMU2043 / RMM2050

CH 1
RM SERIES
Advanced Configuration
Select from the list
of pre-programmed
frequencies
“Frequency x,
To change
press side
button 1 or 2”
SB1 – Monitor Button
SB2 – Channel Select
Frequency
Code
Auto Scan
Active
Channel
Applies to
RMU2040 / RMU2043 / RMM2050

CH 1
RM SERIES
Advanced Configuration
1) Press PTT to cycle
through to the Code
Menu
2) Select from the list
of pre-programmed
codes
“Code x, To
change press
side button 1
or 2”
SB1 – Monitor Button
SB2 – Channel Select
Frequency
Code
Auto Scan
Active
Channel
Applies to
RMU2040 / RMU2043 / RMM2050

CH 1
RM SERIES
Advanced Configuration
1) Press PTT to cycle
through to the Auto
Scan menu
2) Enable / disable by
pressing SB1 or
SB2
“Auto Scan
Disabled, To
change press
side button 1 or
2”
SB1 – Monitor Button
SB2 – Channel Select
Frequency
Code
Auto Scan
Active
Channel
Applies to
RMU2040 / RMU2043 / RMM2050

CH 1
RM SERIES
Advanced Configuration
1) Press PTT to cycle
through to the
Active Channel
menu
2) Add / remove
channels by
pressing SB1 or
SB2
“Active Channels
2, To change
press side
button 1 or 2”
SB1 – Monitor Button
SB2 – Channel Select
Frequency
Code
Auto Scan
Active
Channel
Applies to
RMU2040 / RMU2043 / RMM2050

RM SERIES
Advanced Configuration Frequency
Code
Auto Scan
Active
Channel
PTT (Push-to-Talk)
Button
1) Press PTT to cycle
through the Advanced
Configuration Menu until
you hear the channel
number
2) Select another channel to
configure by pressing SB1
or SB2
“Channel 1”
CH 2
3) Press PTT to
cycle through the
Advanced
Configuration
Menu options for
Channel 2
Applies to
RMU2040 / RMU2043 / RMM2050

RM SERIES
Advanced Configuration
2) PTT (Push-to-Talk)
Button
To exit Advanced Configuration
you can:
1) Power cycle the radio.
Or
2) Press and hold PTT until you
cycle back to top of
programming menu and hear
a ‘beep” then press and hold
PTT until you hear Power up
Audio
“Battery level
high, Channel 1”
Applies to
RMU2040 / RMU2043 / RMM2050
1) Power button

RM SERIES
BUILT TOUGH
TO DO
BUSINESS
BETTER