Motorola AP-8132 User manual

AP-8132 Access Point
INSTALLATION GUIDE

2 AP-8132 Access Point

Installation Guide 3
1.0 Introduction ...............................................4
1.1 Document Conventions ........................................4
1.2 Warnings ...................................................5
1.3 Site Preparation .............................................5
1.4 AP-8132 Package Contents .....................................5
2.0 Hardware Installation .......................................7
2.1 Installation Instructions ........................................7
2.2 Precautions..................................................7
2.3 Access Point Placement........................................7
2.4 Power Injector System.........................................8
2.5 Wall Mount Installation.......................................10
2.6 Suspended Ceiling T-Bar Mount Installation.......................12
2.7 Suspended Ceiling Tile (Plenum) Installation ......................14
2.8 AP-8132 Antenna Options .....................................17
2.9 LED Indicators ..............................................19
3.0 Basic Access Point Configuration ...........................21
4.0 Specifications.............................................38
4.1 Electrical Specifications.......................................38
4.2 Physical Specifications .......................................38
4.3 Radio Specifications .........................................39
5.0 Regulatory Information .....................................40
6.0 Part Numbers, Support, and Sales ...........................48
7.0 Motorola Solutions, Inc. End-User License Agreement .........49
8.0 AP-8132 Access Point China ROHS Compliance ...............52

4 AP-8132 Access Point
1 Introduction
The AP-8132 is a premium, Enterprise class, access point positioned at the top of Motorola Solutions’ access
point product line. The AP-8132 is a plenum rated, 3x3:3 802.11n access point utilizing two 802.11abgn radios.
An AP-8132 model access point uses WiNG 5 software as its onboard operating system. The access point’s unique
WiNG 5 software enables the access point to function as either a Virtual Controller AP capable of adopting and
managing up to 24 additional AP-8132 access points, a Standalone access point or a Dependent mode access
point managed by its connected controller.
If new to Motorola Solutions access point technology, refer to the WiNG Access Point System Reference Guide to
familiarize yourself with access point technology and the feature set supported by the WiNG operating system.
The guide is available, at http://supportcentral.motorola.com/support/product/manuals.do.
This document is written for the qualified network device installer.
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or
equipment malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
!

Installation Guide 5
1.2 Warnings
• Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the AP-8132 model access point.
• Remove jewelry and watches before installing this equipment.
• Verify any device connected to this unit is properly wired and grounded.
• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.
1.3 Site Preparation
• Consult your site survey and network analysis reports to determine specific equipment placement, power
drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Ensure adequate, dust-free ventilation to all installed equipment.
• Identify and prepare Ethernet and console port connections.
• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.
1.4 AP-8132 Package Contents
An AP-8132 access point is available in external antenna models only. An AP-8132 ships with the following:
• AP-8132 access point
• AP-8132 Installation Guide (This Guide)
• Wall mount screw and anchor kit
• Accessories bag (LED light pipe for above the ceiling installations)
NOTE An AP-8132 access point can ship with a separately ordered protective
cover (facade) containing a 6-element MIMO antenna (Part No.
ML-2452-PTA6M6-1). When attached, LEDs continue to illuminate
through the cover (similar to the illustration on the next page). A version
of the facade is also available without the MIMO antenna. This cover
(Part No. 21-8132FAC-01) functions strictly as a protective cover for the
access point and provides no operational functionality.

6 AP-8132 Access Point
1.4.1 Features
An AP-8132 access point minimally supports the following feature set:
• 3 RJ-45 connectors (GE1/POE, GE2 and Console)
• LED indicators
• Slots for wall mounting
• Lock port for Kensington® style security lock
• Two custom dual band radios
• Features for snap-on module support through the access point’s USB interface
• 3x3 MIMO, 3 spatial streams
The AP-8132 access point has two RJ-45 connectors supporting 10/100/1000 Ethernet. GE1/POE accepts 802.3at
or 802.3af compliant power from an external source
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.

Installation Guide 7
2 Hardware Installation
2.1 Installation Instructions
An AP-8132 access point mounts either on a wall (with M4 x 25 pan head screws and wall anchor - or equivalent)
or on a suspended ceiling T-bar.
Once the AP-8132 is installed with facade and cabled, the cables (Ethernet and module connections) should not be
visible when looking directly at the unit (ceiling and wall mounts).
To prepare for the installation:
1. Match the model number on the purchase order with the model numbers in the packing list and on the
case of the access point.
2. Verify the contents of the box include the intended AP-8132 access point, and the included hardware
matches the package contents on page 4.
3. Review site survey and network analysis reports to determine the location and mounting position for the
AP-8132 access point.
4. Connect a CAT-5 or better Ethernet cable to a compatible 802.3at or 802.3af power source and run the
cable to the installation site. Ensure there is sufficient slack on the cable to perform the installation
steps.
2.2 Precautions
Before installing an AP-8132 model Access Point, verify the following:
• Your using the correctly rated power solution for the AP-8132 (either the AP-PSBIAS-2P3-ATR power
injector or the PWRS-14000-247R external power supply)
• Motorola Solutions recommends you do not to install the AP-8132 in wet or dusty areas.
• Verify the environment has a continuous temperature range between 0° C to 50° C.
2.3 Access Point Placement
For optimal performance, install the access point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls
Part Number Description
AP-8132-66040-US 802.11n 3x3:3 access point dual radio US version
AP-8132-66040-WR 802.11n 3x3:3 access point dual radio non-US (rest of world) version
AP-8132-66040-EU 802.11n 3x3:3 access point dual radio European version
NOTE When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable
is recommended for Gigabit operation.

8 AP-8132 Access Point
or floors block transmission. Install the access point in an open area or add access points as needed to improve
coverage.
Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.
Place the access point using the following guidelines:
• Install the access point at an ideal height of 10 feet from the ground.
• Orient the access point antennas vertically for best reception (applies to external antenna models only).
To maximize the access point’s radio coverage area, Motorola Solutions recommends conducting a site survey to
define and document radio interference obstacles before installing the access point.
2.4 Power Injector System
An AP-8132 model access point can receive power via an Ethernet cable connected to the GE1/POE (LAN) port.
When users purchase a WLAN solution, they often need to place access points in obscure locations. In the past, a
dedicated power source was required for each access point in addition to the Ethernet infrastructure. This often
required an electrical contractor to install power drops at each access point location. The Power Injector merges
power and Ethernet into one cable, reducing the burden of installation and allowing optimal access point
placement in respect to the intended coverage area.
The AP-8132’s supported Power Injector (Part No. AP-PSBIAS-2P3-ATR) is a high power POE Injector delivering up
to 30 watts. The access point can only use a Power Injector when connecting the unit to the access point’s GE1/POE
port. The Power Injector is separately ordered and not shipped with an existing AP SKU.
The Motorola access point Power Supply (Part No. PWRS-14000-247R) is not included with the access point and is
orderable separately as an accessory. If the access point is provided both POE power and PWRS-14000-247R power
concurrently, the access point will source power from the PWRS-14000-247R supply only. Disconnecting AC power
from the PWRS-14000-247R, causes the access point to re-boot before sourcing power from the POE power
injector. If the AP is operating using injector supplied power, the AP will not automatically reboot if an AC adapter
is connected. The access point continues to operate with power supplied from the AC adapter without change to
the access point operating configuration. If using AC adapter supplied power and a change to the AP’s operating
configuration is warranted, the access point needs to be manually rebooted by the customer.
CAUTION Using a non-compliant injector, or an injector supporting legacy modes
will not allow the AP-8132 to function at optimum performance levels.
CAUTION Do not plug in the AP-PSBIAS-2P3-ATR Power Injector into the access
point’s Console port. Connecting the Power Injector into the console
port can damage the port and void the AP-8132’s product warranty.
!
!

Installation Guide 9
A separate Power Injector is required for each AP-8132 access point comprising the network.
The Power Injector can be installed free standing, on an even horizontal surface or wall mounted using the power
injector’s wall mounting key holes. The following guidelines should be adhered to before cabling the Power Injector
to an Ethernet source and an access point:
• Do not block or cover airflow to the Power Injector.
• Keep the Power Injector away from excessive heat, humidity, vibration and dust.
• The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance,
ensure the Power Injector is placed as close as possible to the data port.
CAUTION The access point supports any standards-based compliant power
source (including non-Motorola Solutions power sources). However,
using the wrong solution (including a POE system used on a legacy
Motorola Solutions access point) could either limit functionality or
severely damage the access point and void the product warranty.
!

10 AP-8132 Access Point
To install the Power Injector to an Ethernet data source and an access point:
1. Connect the Power Injector to an AC outlet (110VAC to 220VAC).
2. Connect an RJ-45 Ethernet cable between the network data supply (host) and the Power Injector Data In
connector.
3. Connect an RJ-45 Ethernet cable between the Power Injector Data & Power Out connector and the
access point’s GE1/POE port.
Ensure the cable length from the Ethernet source (host) to the Power Injector and access point does not
exceed 100 meters (333 ft).
The Power Injector has no On/Off power switch. The Injector receives power and is ready for device
connection and operation as soon as AC power is applied. Refer to the Installation Guide shipped with the
Power Injector for a description of the device’s LEDs.
2.5 Wall Mount Instructions
A wall mount deployment requires hanging the AP-8132 access point along its width or length using two of three
slots on the bottom of the unit. The AP-8132 can be mounted on to any plaster, wood or cement wall surface using
the provided wall anchors.
The hardware required to install the AP-8132 on a wall consists of:
• Two wide-shoulder Phillips pan head self-tapping screws (M3.5 x 0.6 x 23 mm)
• Two wall anchors
• Security cable (optional)
Optional customer provided installation tools include:
• Security cable
• Philips head screw driver, or drill and drill bit
CAUTION To avoid problematic performance and restarts, disable POE from a
wired switch port connected to an access point if mid-span power
sourcing equipment (PSE) is used between the two, regardless of the
manufacturer of the switch.
CAUTION Ensure AC power is supplied to the Power Injector using an AC cable
with an appropriate ground connection approved for the country of
operation.
CAUTION Cabling a Power Injector to the WAN port (GE2 port) renders the AP
non-operational. Only use a AP-PSBIAS-2P3-ATR Power Injector with
the access point’s GE1/POE (LAN) port.
!
!
!