Motorola AP 7181 User manual

AP 7181
ACCESS POINT
INSTALLATION GUIDE

2AP 7181 Access Point
MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,
Inc. 2013. All rights reserved.

Installation Guide 3
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Deployment Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Installation Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Grounding Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4.1 Ethernet Lighning Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.2 Grouding Hardware Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.5 Minimum Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.1 Site Surveys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.2 Root Node Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.6.3 Non Root Node Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6.4 Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.6.5 Device Deployment Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.7 Antenna Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8 Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.8.1 Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.9 Mounting an AP 7181. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.9.1 Pole Mounted Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.10 Installing an AP 7181 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.10.1 AP 7181 Connections and Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.10.2 LED Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.11 Removing the AP 7181Kit from the Shipping Carton . . . . . . . . . . . . . . . . . . . 19
2.12 Staging the AP 7181 Prior to Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.13 Field Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.13.1 Bottom Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4AP 7181 Access Point
2.10.2 Top Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.14 Remote Panel Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
2.14.1 Preparing the AP 7181 for Remote Panel Antenna Installation. . . . . . . . 43
2.14.2 Installing the Remote Panel Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2.14.3 Installing the Blank Antenna Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.0 Basic Access Point Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.1 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.2 Health and Safety Reccomendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.2.1 Warnings for the Use of Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . 61
4.2.2 Potentially Hazardous Atmospheres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.2.3 Reducing RF Exposure - Use Properly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.3 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4 FCC Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4.1 RF Exposure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.4.2 Intentional and Unintentional Radiators . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.5 Canada Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.6 Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.7 Japan Voluntary Control Council for Interference (VCCI) Class B ITE . . . . . . . . 63
4.8 Waste Electrical and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . 64
4.9 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.0 Motorola Solutions Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Installation Guide 5
1 Introduction
The purpose of this document is to provide installation and setup procedures for the Motorola Solutions AP 7181.
The AP 7181 is a wireless broadband data system that uses mesh networking technology to support wide-area
broadband data coverage. The system offers both 2.4 GHz 802.11b/g/n and 5.x GHz 802.11n Wi-Fi client access
with 2.4 GHz 802.11 b/g/n and 5.x GHz 802.11a/n meshing. The dual-band system supports industry standard client
devices and features easily deployed fixed infrastructure nodes.
The AP 7181 is also designed to meet the needs of large outdoor networks. The network can be configured and
managed for optimal performance using the WiNG management UI.
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations.
1.2 Package Contents
The AP 7181 ships with the following:
• AP 7181 access Point (assembled with mounting yoke attached)
• Power cable
• Optional accessories (in a separate box inside the AP 7181 shipping container)
• AP 7181 Access Point Installation Guide (this document)
NOTE Tips, hints, or special requirements that you should take note of.
CAUTION Care is required. Disregarding a caution can result in data loss or equipment
malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or equipment
damage.
!

6AP 7181 Access Point
2 Hardware Installation
An AP 7181 Access Point installation includes mounting the Access Point, connecting the Access Point to the
network, and applying power. Installation procedures vary for different environments.
2.1 Precautions
Before installing an AP 7181 Access Point, verify the following:
• Become familiar with grounding requirements
• The grounding cable for an AP 7181 must be a #8 gauge (10 mm) wire cross section and use a ring lug
that will fit the M5 grounding screw on the bottom of the unit
• Verify the environment has a continuous temperature range between -40° C to 55° C
AP 7181 Access Points must be installed by trained professionals familiar with RF planning and regulatory limits
defined by the regulatory bodies of the country where the devices are being deployed. All common precautions for
grounding and Electrostatic Discharge (ESD) protection should be observed during deployment and installation. AP
7181 access Points are designed to be installed outdoors and must be installed such that no harmful interference
results from device operation.
• Installations must be performed by professionals who are properly trained and certified,
• Avoid contact with overhead power lines,
• Take precautions to avoid injury from falling tools and equipment. Crews should wear hard hats in and
around the installation work site.
• Be aware of vehicular traffic in and around the installation work site.
• Do not hold any component containing a radio such that the antenna is very close to or touching any
exposed parts of the body, especially the face or eyes, while transmitting.
• Do not operate a portable transmitter near unshielded blasting caps or in an environment where
explosives are present unless the transmitter is especially certified for such use.
CAUTION All device wiring must comply with the National Electric code (NEC) or regulations
and procedures defined by the regulatory bodies of the country or region where the
devices are being deployed. All local building and structure codes must be
observed.
WARNING! Strictly observe the following safety precautions during the AP 7181 installation
procedure.
!

Installation Guide 7
2.2 Deployment Guidelines
Observe the following recommended guidelines to help ensure a successful network deployment:
• Mounting height for network devices should not exceed 30 to 35 feet. Mounting height should vary to
accommodate the topography of the deployment area, foliage, and other obstructions.
• Devices can be deployed using either the Bottom Mount Installation or the Top Mount Installation
procedure.
•Point-to-Point (PTP (Slave)) or Point-to-Multipoint (PMP (SM)) nodes providing backhaul should be oriented
to point away from AP 7181 antenna panels.
• Custom stand-off brackets should be used as required to provide adequate pole separation in an effort to
minimize reflective received power.
• Line of Sight (LoS) guidelines should be given special consideration whenever devices are not installed in
a straight line, such as deploying devices on alternating sides of a roadway.
• Ensure all root nodes are deployed with LoS to the wireless backhaul cluster points.
2.3 Installation Methodology
Consideration of the order in which units are installed when deploying an AP 7181 wireless network can ensure a
more stable and functional network. The PTP backhaul layer should be deployed first. Next, deploy all nodes for the
PMP access Point distribution layer. Next, deploy root node nodes along with PMP Subscriber Modules (SMs) such
that backhaul and network connectivity can be verified or corrected. Finally, deploy all Mesh Point wireless nodes
in order of the least to most hops (1 hop nodes first, followed by 2 hop nodes, etc.).
2.4 Grounding Requirements
The grounding cable for an AP 7181 must be a #8 gauge (10 mm) wire cross section and use a ring lug that fits the
M5 grounding screw on the bottom of the unit.
NOTE For more detailed deployment considerations for backhaul, refer to the Mesh AP 7181
System Planner.
CAUTION It is required all root and portal nodes be adequately grounded. In addition, all root
nodes and portals using the Ethernet port or attached devices (e.g. a camera) must
not only be grounded, but they should also include surge suppression for network
reliability. This is particularly important for network configurations with a public
safety component.
!

8AP 7181 Access Point
2.4.1 Ethernet and Lightning Protection
When installing an AP 7181 root node with a direct connection between the shielded CAT-5E Ethernet and the wired
network, lightning protection should be used on all shielded CAT-5E Ethernet connections.
NOTE Lightning damage is not covered under the conditions of a standard Motorola Solutions
product warranty. When installed correctly, LPUs provide the best protection from the
harmful effects of lightning. Observe all regional and national codes that apply to
grounding for lightning protection.

Installation Guide 9
2.4.2 Grounding Hardware and Connections
The grounding cable for an AP 7181 must be a #8 gauge (10 mm) wire cross section and use a ring lug that fits the
M5 grounding screw on the bottom of the unit (see Grounding Hardware and Connections).
The grounding screw is shown below in green:
When connecting the grounding cable to the unit, tighten the grounding screw from 21.9 - 29.2 inch pounds (lbf-in).
Access points mounted on a metallic pole should be grounded as shown in the following figure:

10 AP 7181 Access Point
Access points mounted on a nonmetallic pole should be grounded as shown in the following figure:
When grounding a unit installed on a non-metallic pole, a ground conductor and rod is required. This requirement
should be factored into the project deployment costs, particularly if the equipment must be installed by a utility
company.
When grounding a unit installed on a wooden pole, a ground conductor and rod is required. This requirement should
be factored into the project deployment costs, particularly if the equipment must be installed by a utility company.

Installation Guide 11
2.5 Minimum Installation Requirements
The minimum requirements for installing an AP 7181:
• AP 7181 Access Point
• Power cable (flying leads)
• Standard Ethernet cable
• Yoke (attached)
• 22 mm socket and driver to remove port caps
• #6 metric allen wrench to remove the yoke
2.6 Access Point Placement
Typically, roadways in the deployment area become main arteries for the wireless mesh network. Roadways can
provide LoS coverage over large distances between root nodes and non root APs.
2.6.1 Site Surveys
Motorola Solutions recommends conducting a site survey prior to installing an Access Point. A thorough site survey
must include a visit to the customer site to identify the characteristics of the coverage area, including availability
of electrical distribution for power sources and the location of existing network infrastructure.The site survey
should also include preliminary WLAN measurements to identify candidate AP locations
When scheduling a visit to conduct a site survey, request access to wiring closets, adjacent floors, and other
locations that may require special permission.
2.6.2 Root Node Placement
When planning for root node placement:
• Identify Root node wireless backhaul technology (Point-to-Point (PTP), Point-to-Multipoint (PMP))
• Identify Ethernet or fiber optic backhaul
• Identify Root node locations
• Obtain all required permits and/or lease agreements
• Verify that power is available at each potential node deployment location
• Give careful consideration to the fact that Root nodes with a wireless backhaul usually backhaul traffic to
a cluster point (i.e. PMP Canopy)
• Wireless backhaul clusters can be on towers, rooftops, etc.
• Ensure that all Root nodes are deployed with LoS to cluster points
When installing an AP 7181 root node that has its Shielded CAT-5E Ethernet directly connected to the wired
network, lightning protection should be used on all Shielded CAT-5E Ethernet connections. An outdoor rated

12 AP 7181 Access Point
Lightning Protection Unit kit such as the HyperLink AL-CAT6HPJW Lightning Protector should be used. For more
information on Motorola Solution's PTP Lightning Protection Unit, refer to the PTP-LPU Technical Specifications.
2.6.3 Non Root Node Placement
The same guidelines as Root nodes apply to Non Root nodes with the exception of a backhaul requirement
The placement of Non Root nodes will depend heavily on the RF network design. Consider the guidelines for
optimizing wireless network performance when identifying potential mounting sites.
In addition, consider the following when planning for Non Root node placement:
• Light Poles, Utility Poles, or Traffic Poles
• Obtain all required supplemental agreements from local governments and utilities
• Obtain a generic mounting agreement that is not specify specific poles, since installation locations
may need to be modified during deployment
• Plan for AC power usage of 84 watts average, 126 watts peak
• The AP 7181 is rated for wind loading of up to160 miles per hour and 30 pounds per square foot.
• Ensure that proper grounding can be established
• The grounding cable for an AP 7181 must be a #8 gauge (10 mm) wire cross section and use a ring lug
that will fit the M5 grounding screw on the bottom of the unit
• Rooftops and Towers
• May require lease agreements
• Identify Access Point locations based on optimal communication with the Root nodes
• Non root node placement will be dependent on asset availability, terrain, etc.
• Ensure that nodes are placed at the same height
• Build the network outward from each root node, from least to greatest number of hops
As with Root node nodes, it should be noted it is incumbent upon the customer to obtain the required pole
attachment agreements for devices to be installed on traffic / utility poles. Obtaining the agreements can be a
lengthy process, so ample lead time must be allowed.
The potential pole locations should be logged with GPS to obtain accurate coordinates. Also log any identifying
numbers on the pole so this information can be provided to the appropriate utility agency. Alternate mounting
locations should also be identified in the event that your initial request is denied.
Specialized brackets may be required for attaching devices to decorative light poles and these brackets may have
to be custom fabricated. In this case, allow enough lead time for ordering the proper equipment.
Also consider any requirements to coordinate requests with multiple utility agencies within the same community.
Verify light pole selections have power available continuously and the power source is within the operational range
of the device being connected.

Installation Guide 13
2.6.4 Mounting Locations
To avoid distortion of the RF pattern, device locations should be chosen such that the AP 7181 ADvanced Element
Panel Technology (ADEPT) antenna panels are at least 30 inches from any nearby metal poles and not co-located
or operating in conjunction with any other antenna or transmitter.The antenna panels must also have a separation
distance of at least 2 meters from anyone who may come into proximity of the AP 7181.
2.6.5 Device Deployment Height
AP 7181 nodes are typically mounted at a height of 30 to 35 feet. Ensure neighboring nodes are mounted at or near
the same device height.
Excessive height should be avoided since this may result in increased congestion and interference in dense RF
environments. This is especially true for the 2.4 GHz band.
Nodes deployed with too great a difference in height or too close to each other may not mesh properly.
Always consider these general guidelines for device deployment height:
• Maintain a typical deployment height of 30 to 35 feet
• For optimum performance, ensure that devices are oriented to have LoS to all neighboring devices
• Locate root nodes which support Wireless Backhaul so that they have LoS to Backhaul clusters or PTP
locations, such as towers
2.7 Antenna Options
The AP 7181 features an integrated ADvanced Element Panel Technology (ADEPT) antenna system designed to take
full advantage of the 802.11n radios. No other antennas are supported.
2.8 Power Options
Details of the power sourcing equipment for the AP 7181 should be handled by a professional installer. The
requirements for deploying the system are:
• Over current protection device with a maximum rating of 20 Amps.
• AP 7181 AC Model - 100-240 VAC input capable of sourcing 180 watts.
• AP 7181 DC Model - Nominal 48 volt power source (41-58 VDC) capable of sourcing 150 watts and battery
floating voltage should not exceed 60 VDC

14 AP 7181 Access Point
2.8.1 Power Cables
Flying lead power cables are available based on the country of operation.
If the units will be plugged directly into an electrical wall outlet, power plug adapters are available for North
America, Europe, and Australia.
Four Wire AC Right Angle Power Cable
(North America and International)
Black (Line)
White (Neutral)
Red (Unused)
Green/Yellow (Ground)
Three Wire AC Power Cable
(International)
Brown (Line)
Blue (Neutral)
Green/Yellow (Ground)
Two Wire DC Power Cable
(North America and International)
Black (Negative)
Red (Positive)
CAUTION Never plug a power cable wired to a power source for an AC unit into a DC unit.
CAUTION Do not use the connector on the power cables for interrupting current. Never
actively plug or unplug the connector while the cable is energized.
!
!

Installation Guide 15
2.9 Mounting an AP 7181
The AP 7181 Access Point is designed for outdoor installations. All hardware installations should be performed by
a professional installer.
Devices can be deployed using either the Bottom Mount Installation or the Top Mount Installation procedure.
2.9.1 Pole Mounted Installations
The optional wall gooseneck can also be used with the pole adapter for pole mounting.
The wall gooseneck dimensions are 10x12x6 inches and it weighs 4 pounds. The pole adapter dimensions are
4x2.62x7 inches and it weighs 3 pounds.
The gooseneck attaches to the yoke, which can be attached to the top or the bottom of the AP 7181. Secure the
gooseneck and adaptor to the pole with the threaded portion pointing either up or down using band clamps.
If using a bottom mount, drill a 1/2 inch diameter hole at the lowest point on the bend to allow water to drain from
the gooseneck.
2.10 Installing an AP 7181
The following guidelines and procedures should be observed when installing an AP 7181 Access Point.
The following is a list of the minimal tool set required to install an AP 7181 device:
• 24 mm socket and driver - for cable gland
• 22 mm socket and driver - for GE1 and GE2 port caps
• 19 mm socket and driver - for console port cap
• 21 mm socket and driver - for set screw
• 8 mm socket and driver - for grounding screw
• 6 mm allen wrench bit - for mounting bracket (yoke)
• T27 Torx bit - for the radome antenna panels and sun shields
• Torque screwdriver - for the radome antenna panels and sun shields
• Torque wrench

16 AP 7181 Access Point
• Adjustable wrench
• Standard level
• Anti-seize lubricant
You may also need a Phillips screw driver and a 2.5 mm allen wrench.
2.10.1 AP 7181 Connections and Ports
The power cable, grounding connections, power indicator light, Ethernet ports, and LED status panel on the bottom
the AP 7181 are shown in the figure below:
NOTE The grounding cable for an AP 7181 must be a #8 gauge (10 mm) wire cross section
and use a ring lug that will fit the M5 grounding screw on the bottom of the unit.

Installation Guide 17
The two pin DC power connector (phase-in) is shown below. All other connections, ports, and the LED status panel
are the same.
The horizontal (HP) and vertical (VP) connectors for the antenna cables are located on the top of the AP 7181.
All radome antenna panel cables are labeled as HP or VP. Attach each cable to the corresponding connector when
performing a remote panel installation or any other procedure which requires attaching antenna cables to the
connectors.
NOTE The connectors on the AP 7181 are Ingress Protection 67 (IP67) rated. No additional
weatherproofing precautions are required.

18 AP 7181 Access Point
2.10.2 LED Status Indicator Panel
There are six LEDs on the AP 7181 which can be viewed through the light pipes on the bottom of the unit. The LEDs
have the following display characteristics and functionality:
WARNING! When disconnecting the antenna cables from the unit or removing an antenna panel
and replacing it with a blank panel, terminators MUST be placed on the unused
horizontal and vertical connectors on the top of the unit. The terminators on the AP
7181 are Ingress Protection 68 (IP68) rated. No additional weatherproofing
precautions are required.
LED 1 LED 2 LED 3 LED 4 - 5 GHz LED 5 - 2.4 GHz LED 6
Blinking Red
indicates
booting. Solid
Red defines a
failure
condition.
White
defines
normal
operation.
Green
defines
normal GE1
operation.
Yellow
defines a
collision.
Green
defines
normal GE2
operation.
Yellow
defines a
collision.
Amber
defines 5 GHz
radio as
configured.
Emerald
defines 2.4
GHz radio as
configured.
Not used.

Installation Guide 19
2.11 Removing the AP 7181 Kit from the Shipping Carton
1. Open the shipping carton and remove the packaging material on the top of the Access Point.
CAUTION Never lift an AP 7181 using the radome antenna panels or other plastic parts.
Always lift the unit by the yoke or metal antenna rings.
WARNING! An AP 7181 unit weighs 39 pounds. Use all appropriate cautions when lifting and
consider a two man lift when necessary.
!

20 AP 7181 Access Point
2. Remove the accessories box from the shipping carton.
In the accessories box, locate the following items:
• Weatherproof Ethernet port adaptor (cable gland) (part number: HKLN4486A)
• Waterproof Console Port Adapter (part number: HKLN4485A)
• Power Cable (part number: 30009307001, 30009308001, or 30009315002)
• Sun Shields with Captive Screws (part number: HKLN4446A)
• Yoke (Mounting Bracket) (part number: HKLN4484A)
• Set Screw for Yoke (part of the complete AP 7181 kit)
3. Open the plastic bag covering the unit.
4. Roll the plastic bag to the bottom of the shipping carton. Using the yoke or antenna ring, carefully remove
the unit from the box. This method prevents damage to the antenna assembly.
NOTE Only one set screw is included with each AP 7181 kit. If a second set screw is required,
purchase an M14x2.0, 20mm stainless steel Hexagonal screw.