Motorsports 350Z User manual

Page
Revision IR
8/31/2020
JC
1
2877 Carrollton - Villa Rica Hwy Carrollton, GA 30116 770.838.7777
350Z Hood Strut Kit
Installation Guide
PROLOGUE:
Study these instructions completely and thoroughly before proceeding to assemble. Installation can
be completed using common tools and automotive procedures. The installer must have a thorough
knowledge of automotive systems operation. If unfamiliar with any of the concepts outlined in this
instruction, we recommend the installation be completed by a qualified professional.
WARNING! Extreme caution should be taken when performing ANY maintenance or performance
upgrades to your Vehicle. Please observe and abide by any Warning or Caution labels placed on the
various components and tools used when servicing your Vehicle. If you have any questions regarding
installation or the various components included with the 350Z Hood Strut Kit,
consult with a Professional Mechanic or contact Z1 Motorsports for more information.

Page
Revision IR
8/31/2020
JC
2
Parts Included:
Item
Quantity
Description
1
2
Hood Strut Assembly
2
2
Hood Strut Brackets
3
2
Ball Studs
Tools Required:
•10mm and 12mm Socket
•Ratchet
•Dremel or similar cutting instrument
•Clip Removal tool
•Screwdriver
Safety Requirements:
•Always wear safety glasses and any necessary protective garments. If using any fluids, chemicals, or
solvents, a respirator is recommended.
•Always use properly rated jack stands when working under your Vehicle.
•Always keep limbs and parts away from moving drivetrain parts.
•Only operate drivetrain in safe space and well-ventilated areas.
*BEFORE YOU BEGIN!
Remove contents from the Z1 Motorsports 350Z Hood Strut Kit and verify that ALL necessary hardware is present.
Procedure:
1. Assure the car’s engine is turned off and place transmission in Park position (or in Reverse gear if
equipped with a manual transmission). Apply Parking Brake.
2. Unlatch, raise, and safely support Hood.
3. Starting with the right side, remove the battery cover shroud by removing the (5) clips securing the panel to
the vehicle.
4. Using a 10mm socket, remove the fender bolt circled below.

Page
Revision IR
8/31/2020
JC
3
5. Locate provided Ball Studs. Install Ball Stud into factory fender bolt location. Torque to 10 ft-lbs.
6. Using a Dremel, trim the battery cover shroud. Be sure to trim enough of the panel so that it easily fits with
the ball stud installed.
7. Re-install battery cover shroud.
Note: The following steps are best completed with an additional person to help hold the hood of the vehicle.
8. While holding the hood, use a 12mm socket remove the (2) nuts securing the hood hinge to the hood.
9. Install the Hood Strut Bracket onto the studs protruding from hood. The ball end should point away from
the engine bay.

Page
Revision IR
8/31/2020
JC
4
10. Install the Hood Strut onto the Ball Stud by pressing the Socket End located on the shaft side of the Hood
Strut firmly onto the ball stud.
Note: Socket End of Hatch Strut Assembly should ‘snap’ onto Ball.
11. Remove the locking pin on the ball stud found on the housing side of the Hood Strut assembly by rotating
pin and pulling down.
12. Install Socket End of Hatch Strut onto the Z1 Lower Mounting Plate.
Note: Lift up slightly on Hood for Socket End to slide over Hood Strut Bracket Ball. If Socket End is not oriented in
line to snap onto Ball, simply rotate Strut Housing until aligned.
Note: Socket End of Hatch Strut Assembly should ‘snap’ onto Ball.
13. Install locking pin by inserting through hole on ball end. Once inserted, rotate locking pin and snap into
place.
14. Repeat steps 2-12 for opposite side of the vehicle.
15. Slowly lower hood. Check for fitment and smooth operation. Assure the hood latches normally.
Note: If your hood does not line up as it did before, you can adjust the fitment via the hood hinge bracket.
End
Additional Technical Support:
Contact Z1 Motorsports at [e-mail]
Or call 770 838 7777 between 9am and 6pm ET