motortronics VMX-synergy VMX-SGY-010-N4 User manual

VMX-synergy'·
IP 66 REMOTE KEYPAD USER GUIDE

VMX-SGY-010-N4
User Guide
Motortronics UK Ltd
Bristow House
Gillard Way
Ivybrdge, UK
www.motortronics-uk.co.uk
© 2019 by Motortronics UK Ltd all rights reserved
Copyright subsists in all Motortronics UK Ltd deliverables including
magnetic, optical and/or any other soft copy of these deliverables.
This document may not be reproduced, in full or in part, without
written
permission. Enquiries about copyright of Motortronics UK
Ltddeliverables should be made to Motortronics UK Ltd. If, by
permission of the copyright owner, any part of this document is
quoted, then a statement specifying the original document shall be
added to the quotation. Any such quotation shall be according to
the original (text, figure or table) and may not be shortened or
modified.

VMX-synergy™ - IP 66 Remote Keypad User Guide
1 | P a g e
Introduction
The remote keypad (VMX-SGY-010-N4) can be used to control,
monitor and program up to 32 VMX-synergy™ soft starters.
The remote unit is powered from the host VMX-synergy™ and
requires only an Ethernet cable for communication.
Installation
The remote keypad can only be used with the standard ‘on-board’
Modbus RTU connection. It cannot be used with Anybus modules.
The remote touchscreen is a Modbus RTU master device. A PLC,
HMI, or other Modbus Master device cannot be used on the same
network while the remote touchscreen is connected.
Remote Keypad Setup VMX-SGY-010-N4
4.20" (112mm)
3.60" (91mm)
PEEL OFF
BACKING AND
DISCARD
ORIENTATION
LABEL
PEEL OFF
BACKING AND
DISCARD
CUT OUT

VMX-synergy™ - IP 66 Remote Keypad User Guide
2 | P a g e
Network Connection
Keypad to one VMX-synergy™ unit
For a configuration where there is only one VMX-synergy™ unit (one-
to-one the remote and main unit can be directly cabled. See Diagram
below:
A RJ45 to RJ12 adaptor cable is included as part of the kit (PN: VMX-
SGY-014). The use of this adapter is recommended to ease network
installation and reduce the possibility of incorrect wiring.
Keypad to multiple VMX-synergy ™ unit
For multiple base units connected to the keypad, the use of VMX-
SGY-011 is highly recommended. See diagram below.
RemoteKeypadSetup(Continued)
VMX-SGY-015 [ ]
(or CAT5 cable to suit length required)
VMX-SGY-014 (Included)
VMX-SGY-011
Close Jumper
VMX-
SGY-014
VMX-
SGY-026
VMX-
SGY-035
VMX-Synergy™#1
VMX-Synergy™
#2
VMX-Synergy™#n

VMX-synergy™ - IP 66 Remote Keypad User Guide
3 | P a g e
Remote Keypad Operation
Ensure starter’s Modbus Network Settings are: Even parity and 19200
baud rate. If connecting to multiple starters, set the Address to a
unique number for each VMX-synergy™ starter.
If remote touchscreen start/stop control is desired, set the Control
Method to Modbus Control. If the remote touchscreen will only be used
for monitoring or configuration (digital input or local touchscreen start/
stop control will be used), select the appropriate setting (Local
Touchscreen, User Programmable, 2-wire control, or 3-wire control).
Connect remote touchscreen using the VMX-SGY-014 adapter (VMX-
synergy™ end) and a standard Ethernet patch cable. If connecting to
multiple starters, a Modbus splitter (VMX-SGY-011) will be required for
the first starter. VMX-SGY-026 may be used for the remaining units
On the remote touchscreen go to Modbus Network Settings as shown
in Fig 1. and select Scan Bus. This will show all the VMX-synergy™
starters on the bus (Fig 2). Select which starter you wish to connect to.
Alternatively, you can select the Address number and then select
“Connect” to connect to that particular starter.
The status screen Fig 3 on the remote touchscreen will display the
current starter it is connected to, by displaying the starter’s node
address and serial number (Example: address 01 and serial number
A0167805).
Figure 1. Figure 2. Figure 3.
RemoteKeypadSetup (Continued)

VMX-synergy™ - IP 66 Remote Keypad User Guide
4 | P a g e
The remote touchscreen’s control for starting and stopping overrides
the starter’s onboard touchscreen when the starter’s Control Method
is set to Modbus Control. Menu navigation, configuration, and
monitoring are still possible on the starter’s touchscreen.
Press the starter icon box on the Status screen of the remote
touchscreen to change to another starter if controlling multiple
starters from one remote touchscreen.
When using the remote touchscreen for start/stop control the remote
touchscreen has full control, configuration, and monitoring
capabilities, while the local touchscreen on the starter only has
configuration and monitoring capabilities. Digital outputs always
function as programmed, regardless of Control Mode. Digital inputs
are disabled during Modbus Control and Keypad Control Modes, but
are active during all other Control Modes.
The remote touchscreen can be used for monitoring and
configuration during any other control method besides Modbus
Control.
California Customers:
California Proposition 65 Warning
WARNING: this product and associated accessories may contain chemicals
known to the State of California to cause cancer, birth defects, or other
reproductive harm. For more information visit https://p65warnings.ca.gov
RemoteKeypadSetup (Continued)

VMX-synergy™ - IP 66 Remote Keypad User Guide
5 | P a g e
Notes

VMX-synergy™
Motortronics UK Ltd Bristow House
Gillard Way
Ivybridge, UK
[phone]
www.motortronics-uk.co.uk
MA N-SGY-044- V 0 2
IP 66 REMOTE KEYPAD USER GUIDE