MotoSleep Tilt Soft Form Series User manual

OWNER’S MANUAL
TSF2WM Rev 2.0 11/2021
Tilt Soft Form Series
1
STOP
2
HEAD FOOT TILT

Installation Guide
1Open the box lid.
×1
Mattress Retainer Bar
×1
Accessories Box
2Take out all the accessories from the packaging and put them
aside. All electronics and components that need to be installed are
located in boxes under the foundation or attached to the frame.
Before discarding the packing materials, ensure that all the parts
are accounted for.
ACCESSORIES BOX:
×4
Legs
×1
AC Power
Cord
×3
AAA
Batteries
×1
Remote
Control
×1
Power Supply with
Battery Backup Box
9V 9V
9V
(Optional)
HEAD BOARD
HEAD BOARD
3Install 4 legs, make sure the legs are tight. Take the bed out of the box
, turn over onto 4 legs .
Remove the box. Uncoil the DC power cord (connected to the
control box) and put it to the side of the bed.
4
HEAD BOARD
DC power cord
×1
Sync Cord
（TXL/T/CKS/TXL+
Only）
1
STOP
2
HEAD FOOT TILT

1
STOP
2
HEAD FOOT TILT
5Install the mattress retainer bar
one side after another.
2
1
6Uncoil the AC power cord, connect the DC power cord to the power supply and then
connect the power supply to the AC power source.
the remote control.
Insert the batteries into
HEAD BOARD
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
DONE!

Remote Control Instructions
1
STOP
2
HEAD FOOT TILT
Home Position
Head Massage on
（3 Intensity Levels）
Programmable
Positions
Head/Foot
Massage off
Lifts
Lowers
Foot Massage on
（3 Intensity Levels）
Under Bed
LED on/off
ADJUST
This button lifts the head/foot/tilt section of the foundation.
This button lowers the head/foot/tilt section of the foundation.
One touch programmable positions.
2
1
SETTING PROGRAMMABLE POSITION
MASSAGE FEATURES
Turn on the head massage. Cycle through 3 massage intensities.
Turn off the head/foot massage.
STOP
Turn on the foot massage. Cycle through 3 massage intensities.
ONE TOUCH BUTTON
One touch flat position.
One touch underneath LED lighting on/off.
Setting Programmable Position
Adjust the head,foot and lumbar to your desired position.
To adjust a saved position, repeat step 1 and 2 and the new position will
be saved.
Press and hold the LED on/off button first, then press and hold one of
the picture programmable buttons for 5 seconds until you hear a
beep sound. The position is then saved.
1 2
STEP 1：
STEP 2：
STEP 3：
Pairing Remote
Make sure the batteries are good. Replace
them when needed.
Unplug the power cord from the power source. If 9V backup batteries
were installed in the power supply, remove them.
Press and hold and simultaneously until the blue
backlights of the remote control are off.
STEP 1：
STEP 2：
STEP 3：
STEP 4：
Plug the power cord back into the power source. You will hear an activation
sound in 2 seconds, indicating the remote is paired to the power foundation.
1
STOP
2
HEAD FOOT TILT
AAA AAA
AAA
The original remote that comes in the box is already
paired to the foundation. No further action is
required. In the event when the remote is not paired
with the foundation, follow the pairing instructions
below.

Electronics Quick Reference Guide
USB
Charger
Head Motor
Foot Motor Tilt Motor
Power Supply
HD Motor FT Motor TILT Motor HD Massage FT Massage
LED PROG APP SYNUSBPower
LED
DC
Power Cord
AC
Power Cord
CB18
Control Box
WIRELESS RECEIVER
Remote Control
Foot Massage
Motor
Head Massage
Motor
1
STOP
2
HEAD FOOT TILT
Wireless Syncing Instruction
UN-SYNC Two Foundations
STEP 1：Make sure both remotes are individualy paired to
the foundation. If the remote is not paired with the
foundation, follow the pairing instructions.
STEP 2：Make sure both foundations are at home (flat
position).
STEP 3：Press and hold HEAD and on both remotes
at the same time for 5 seconds, or/until the blue
BACK LIGHTS FLASH.
Press and hold HEAD and HEAD on both remotes
at the same time for 5 seconds, or/until the blue BACK
LIGHTS FLASH.
Press
and hold
Press
and hold
1
STOP
2
HEAD FOOT TILT
1
STOP
2
HEAD FOOT TILT
Synchronizing Two Foundations with Sync Cord
STEP 1：Unplug foundations from the power source.
STEP 2：Connect the male ends of the sync cord to the female sync plugs of the control boxes
(Refer to below illustration).
STEP 3：Plug foundations back into the power source.
STEP 4：
Check to ensure all cords are securely attached.Either remote will operate both
foundations simultaneously.
Sync Plug
Sync Plug
Control Box 1 Control Box 2
Sync Cord
HD Motor FT Motor Neck Motor
HD Massage FT Massage
LED PROG APP SYNUSBPower
HD Motor FT Motor Neck Motor
HD Massage FT Massage
LED PROG APP SYN
USB
Power
Sync Cord
If simultaneous operation of two foundations is
desired, please follow the steps listed below.
Sync cable is not required if both
adjustable bases are equipped with
V2.0 or newer remote controls. If the
bases are equipped with V2.0 remote controls, follow
the “Wireless Syncing Instruction”.
If the adjustable bases are not equipped with V2.0 on
newer remote controls, follow the “Synchronizing
Two Foundation with Sync Cord” instruction.
Model No.:******
****** V2.0

Open www.motosleep.com from your browser.
Scroll down to the bottom of the page and press download.
In the download page, tap the download button to download the app.
Open the download file and install the app.
MotoSleep Mobile APP（Optional）
Open APP Store on your IOS device
Tap the Magnify Glass Icon and search with the keyword
Tap on and to install the APP
Wait for the download/installation to be complete
GET
+INSTALL
Customer Service Toll Free:1-844-696-6886
www.motosleep.com
REMOTECONTROL
REMOTECONTROL
HEAD FOOT
REMOTECONTROL
REMOTECONTROL
1
STOP
2
REMOTECONTROL
1 2
TV Z-G
SNORE
REMOTECONTROL
2
1
STOP
REMOTECONTROL
SNORE
TV Z-G
2
1
REMOTECONTROL
1
STOP
2
TV Z-G
SNORE
OWNER’S MANUAL
Four-button Remote Control Three-button Remote Control
Five-button Remote Control
Eleven-button Remote Control
Eleven-button Remote Control
Ten-button Remote Control
Ten-button Remote Control
Thirteen-button Remote Control
Thank you for purchasing a MotoSleep
Power Foundation.
General Information
Install the MotoSleep APP
IOS
Android
The Built-in Owner’s Manual at your fingertip
* Remote interface varies in between different MotoSleep Power Foundation models. If you wish to
disconnect from the current paired Power Foundation, Enter the Settings Page and tap the
Disconnect button.
MotoSleep Mobile APP is a mobile application to control the MotoSleep Power Foundation with
mobile devices. The application is available for both iOS and Android based smart devices.
The MotoSleep Mobile APP uses the latest technology to communicate with your MotoSleep
Power Foundation. Make sure your mobile devices has the pairing function for the APP to
work correctly.
Before you start. Switch on the pairing function on your mobile device. Make sure your
MotoSleep Power Foundation is correctly connected and is power-on.
The MotoSleep APP will automatically pair your MotoSleep Power Foundation once you start the
APP and does not require additional settings.
* The effective connection range is ± 10m
8
7
6
5
4
3
2
1
List of MotoSleep Products within
the connection range*
Tap the Refresh Button to refresh
the MotoSleep Products List
Enter the Settings Page
Back to the Home Screen
9
Serial Number of the control box
Owner’s Manual Page
Troubleshooting
Disconnect from the paired
MotoSleep Product
Rename your MotoSleep Power
Foundation of your choice
Home Screen
Settings Page
9
SELECT DEVICE
BED
Refresh
3
1
2
SETTINGS
DISCONNECT
Serial Number
5
4
RENAME
OWNER’S MANUAL
6
7
TROUBLESHOOTING
8
2
1
STOP
REMOTE CONTROL
1
2
6
3
4
3
4
3
4
5 7
108 9
1
10
9
8
7
5
4
3
2
6
HEAD FOOT TILT
Head/Foot/Tilt Lifting function
Head/Foot/Tilt Lowering function
One touch flat Position
Enter the Setting Page
Head Massage (3 different intensities)
Foot Massage (3 different intensities)
Massage Off Button
Programmable Position 1
Programmable Position 2
Under Bed Lighting
MotoSleep APP Home Screen
Device Pairing
MotoSleep APP Remote Control