MotoSleep XFB User manual

OWNER’S MANUAL
LPB5NM Rev 8.0 03/2022
HEAD FOOT
XFB/XSF Low Prof ile Bed

Setup the power foundation without the bed frame.
1Open the box lid.
HEAD BOARD
HEAD FOOT
2Take out all the accessories from the packaging and put
them aside. All electronics and components that need to
be installed are located in boxes under the foundation or
attached to the frame. Before discarding the packing
materials, ensure that all the parts are accounted for. ×1(2 for K/CK)
Mattress Retainer Bar
×1
Accessories Box
ACCESSORIES BOX:
×1
AC
Power Cord
×1
Remote
Control
×1
Power Supply with
Battery Backup Box
9V 9V
9V
(Optional)
×3
AAA
Batteries
AAA
×1
Sync Cord
（TXL/T/CKS Only）
×6
Adjustable Legs
Remove the red plastic safety lock before unfolding your power foundation.
3Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin

HEAD BOARD
DC Power Cord
Control Box
4Install 4 legs, make sure the
legs are tight.
HEAD BOARD
6Flip the foot end of the bed from the box and lay it
on top of the end at the headboard.
HEAD BOARD
7Install the remaining 2 legs on the foot end of the
bed, make sure the legs are tight.
Uncoil the DC power cord (connected to the control
box) and put it to the side of the bed.
HEAD BOARD
5Remove the bed from the box
with a flipping
motion, let the
bed stand on the 4 legs.

the remote control.
Insert the batteries into
HEAD FOOT
AAA AAA AAA
9bar one side after another.
Install the mattress retainer
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
HEAD BOARD
10 Uncoil the AC power cord, connect
the DC power cord to the power
supply and then connect the
power supply to the AC
power source.
DONE!
2
1
8Make the bed completely flat.
HEAD BOARD

the remote control.
Insert the batteries into
HEAD FOOT
1
HEAD BOARD
DC Power Cord
2Make the bed completely flat
with a flipping motion .
3Install the mattress retainer bar one side after another.
HEAD BOARD
DC Power Cord
2
1
HEAD BOARD
DC Power Cord
HEAD BOARD
4Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply to the AC
power source.
Setup the power foundation with the bed frame and slat base.
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
Take the bed out of the box, put it on the slat base , do not install
any legs. Uncoil the DC power cord (connected to the control box)，
pull the DC power cord towards the direction of the AC power source
through either the bottom or the side of the bed frame.
AAA AAA AAA

USB
Charger
Sync Cord
Power Supply
Head Motor Foot Motor
HD Motor
LED APP SYN
FT Motor USB Power
DC
Power Cord AC
Power Cord
WIRELESS RECEIVER
CB11B
Control Box
Electronics Quick Reference Guide
Wireless Syncing Instruction
UN-SYNC Two Foundations
STEP 1：Make sure both remotes are individualy paired to
the foundation. If the remote is not paired with the
foundation, follow the pairing instructions.
STEP 2：Make sure both foundations are at home (flat
position).
STEP 3：Press and hold HEAD and on both remotes
at the same time for 5 seconds, or/until the blue
BACK LIGHTS FLASH.
Press and hold HEAD and HEAD on both remotes
at the same time for 5 seconds, or/until the blue BACK
LIGHTS FLASH.
Press
and hold
Press
and hold
If simultaneous operation of two foundations is
desired, please follow the steps listed below.
Sync cable is not required if both
adjustable bases are equipped with
V2.0 or newer remote controls. If the
bases are equipped with V2.0 remote controls, follow
the “Wireless Syncing Instruction”.
If the adjustable bases are not equipped with V2.0 on
newer remote controls, follow the “Synchronizing
Two Foundation with Sync Cord” instruction.
Model No.:******
****** V2.0
Synchronizing Two Foundations with Sync Cord
STEP 1：Unplug foundations from the power source.
STEP 2：Connect the male ends of the sync cord to the female sync plugs of the control boxes
(Refer to below illustration).
STEP 3：Plug foundations back into the power source.
STEP 4：
Check to ensure all cords are securely attached.Either remote will operate both
foundations simultaneously.
HEAD FOOT
Remote Control
HEAD FOOT
HEAD FOOT
Sync Plug
Sync Plug
Control Box 1 Control Box 2
HD Motor
LED APP SYN
FT Motor USB Power
HD Motor
LED APP SYN
FT Motor USB Power
Sync Cord

Remote Control Instructions
ONE TOUCH BUTTON
One touch flat position.
HEAD FOOT
Lifts and
Lowers Head
Lifts and
Lowers Foot
Flat Position
This arrows lift and lower the
head section of the foundation.
This arrows lift and lower the
foot section of the foundation.
ADJUST
Make sure the batteries are good. Replace them
when needed.
STEP 1：
Unplug the power cord from the power source.
If 9V backup batteries were installed in the
power supply, remove them.
STEP 2：
HEAD FOOT
STEP 3：
Press and hold and simultaneously
until the blue backlights of the remote control
are off.
Pairing Remote
Press And
Hold
Plug the DC power cord back into the power source. You will hear an activation
sound in 2 seconds, indicating the remote is paired to the power foundation.
STEP 4：
AAA AAA
AAA
The original remote that comes in the box is already paired to the foundation.
No further action is required. In the event when the remote is not paired with
the foundation, follow the pairing instructions below.

MotoSleep Mobile APP（Optional）
HEAD FOOT
REMOTE CONTROL
Before you start. Switch on the pairing function on your mobile device. Make sure your
MotoSleep Power Foundation is correctly connected and is power-on.
The MotoSleep APP will automatically pair your MotoSleep Power Foundation once you start
the APP and does not require additional settings.
GET
+INSTALL
www.motosleep.com
REMOTECONTROL
REMOTECONTROL
HEAD FOOT
REMOTECONTROL
REMOTECONTROL
1
STOP
2
REMOTECONTROL
1 2
TV Z-G
SNORE
REMOTECONTROL
2
1
STOP
REMOTECONTROL
SNORE
TV Z-G
2
1
REMOTECONTROL
1
STOP
2
TV Z-G
SNORE
OWNER’S MANUAL
Four-button Remote Control Three-button Remote Control
Five-button Remote Control
Eleven-button Remote Control
Eleven-button Remote Control
Ten-button Remote Control
Ten-button Remote Control
Thirteen-button Remote Control
Thank you for purchasing a MotoSleep
Power Foundation.
* The effective connection range is ± 10m
8
7
6
5
4
3
2
1
List of MotoSleep Products within
the connection range*
Tap the Refresh Button to refresh
the MotoSleep Products List
Enter the Settings Page
Back to the Home Screen
9
Serial Number of the control box
Owner’s Manual Page
Troubleshooting
Disconnect from the paired
MotoSleep Product
Rename your MotoSleep Power
Foundation of your choice
Home Screen
Settings Page
9
SELECT DEVICE
BED
Refresh
3
1
2
SETTINGS
DISCONNECT
Serial Number
5
4
RENAME
OWNER’S MANUAL
6
7
TROUBLESHOOTING
8
MotoSleep Mobile APP is a mobile application to control the MotoSleep Power Foundation with
mobile devices. The application is available for both iOS and Android based smart devices.
The MotoSleep Mobile APP uses the latest technology to communicate with your MotoSleep
Power Foundation. Make sure your mobile devices has the pairing function for the APP to
work correctly.

HEAD BOARD
Lift the head and foot end of the bed by remote control. Install four stabilizer
brackets as shown. Use a phillips screwdriver and socket wrench to tighten
the screws and bolts.
Screws
ST4.2×16
M8*16 Bolts
Washers
Headboard Bracket Installation Guide (Optional)
Headboard brackets are optional and not included. A 1/2” (13 mm)
socket and 1/2” (13 mm) wrench are required to complete the installation.
12
2
1
a)Align the slot hole of the headboard bracket to the sleeve into
which the leg threads. DO NOT OVERTIGHTEN. Too much force
may damage the thread.
b)The headboard bracket has 2 adjustable slots to accommodate
any frame type. Use the bolts and washers to secure the bracket.
Make sure the bolts are tight.
a)To put the T-Bracket and Headboard Bracket together, you will
need (2) M8×16 bolts and (2) nuts. Slip the bolts through the holes
from T-Bracket to Headboard Bracket with the head of bolt facing
outward. Use the 1/2” (13 mm) socket and 1/2” (13mm) wrench to
tighten the bolts.
You may now connect your headboard to the attachment plates using the remaining short bolts
and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2” (13mm)
socket and 1/2” (13mm) wrench to tighten the bolts.
(2) Headboard Brackets (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers
Slat Pack Installation Guide (Optional)
Stabilizer Brackets are optional and not included. They can fix the
bed onto the slat base. A phillips screwdriver and socket wrench are
required to complete the installation.
(4) Stabilizer Brackets (1) Socket Wrench(8) Screws ST4.2×16 (8) Bolts M8*16 (8) Washers
STABILIZER BRACKETS COMPONENTS
Support leg may be needed on some slat/platform bed frames, refer
to the leg configuration table for height adjustment.
* Make sure the adjustable legs are properly tight, and the plastic caps have been placed at
the bottom of the legs. Incorrect installation might cause the part to fail or damage the floor.
OPTIONAL EQUIPMENT/PART (NOT INCLUDED)
Socket and Wrench 1/2'' (13mm)
(6)
SLAT/ PLATFORM
LEGS
Leg
Configuration
Leg Height
Leg Configuration Table
4 " 7⁵⁄8 " 11³⁄8 " 16¹⁄2 "

Customer Service Toll Free:1-844-696-6886
Install two spacing connectors to ensure the gap between the two adjustable bases is consistent.
Spacing Connector for TXL/T/CKS (Optional)
(2) SPACING CONNECTOR (TXL/T/CKS ONLY)
Lift the head and foot end of the bed by remote control. Install the spacing connector as shown.
Spacing
Connector
Bed Frame
Bed Frame
PRODUCT PROTECTED BY FOLLOWING PATENT:
— US PATENT: 10, 306, 994