MotoSleep XSF User manual

OWNER’S MANUAL
LPB14W4MSC Rev 1.0 08/2022
XSF Low Prof ile Bed
With Motion Sensor And Immersive Audio System

Setup the power foundation without the bed frame.
1Open the box lid.
HEAD BOARD
2
Take out all the accessories from the packaging and put them aside. All electronics and components
that need to be installed are located in boxes under the foundation or attached to the frame. Before
discarding the packing materials, ensure that all the parts are accounted for.
×1(2 for K/CK)
Mattress Retainer Bar
×1
Accessories Box
×1
Immersive Audio
System Box
Mounting
Bracket
×2 ×2
Motion
Sensor
ACCESSORIES BOX:
×1
AC
Power Cord
×1
Remote
Control
×1
Power Supply with Battery
Backup Box
9V 9V
9V
(Optional)
×3
AAA
Batteries
AAA
×1
Sync Cord
（TXL/T/CKS Only）
×6
Adjustable
Legs

5
HEAD BOARD
Remove the bed from the box
with a flipping motion, let the
bed stand on the 4 legs. 6Flip the foot end of the bed
from the box and lay it on top
of the end at the headboard.
HEAD BOARD
4Install 4 legs, make sure the
legs are tight.
HEAD BOARD
Remove the red plastic safety lock before unfolding your power foundation.
3Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin

7
HEAD BOARD
DC Power Cord
Control Box
Install the remaining 2 legs on
the foot end of the bed, make
sure the legs are tight.
Uncoil the DC power cord
(connected to the control box)
and put it to the side of the bed.
8Motion sensor installation = +
Motion
Sensor
Mounting
Bracket
Prepare The Motion Sensor Hardware.
Connect The Motion Sensor Connectors.
STEP 1: Connect the motion
sensor to the mounting
bracket.
STEP 2: Rotate the
mounting bracket 90
degrees clockwise
STEP 3:
DONE !
STEP 2: Connect the motion sensor connectors as illustrated.
Note there are two connectors, one on each side of the bed.
STEP 1: Clip the mounting bracket onto the center adjustable legs as illustrated.
HEAD BOARD

10 one side after another.
Install the mattress retainer bar
2
1
11 Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply
to the AC power source.
9Make the bed completely flat.
HEAD BOARD
the remote control.
Insert the batteries into
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
HEAD BOARD
AAA AAA AAA
DONE!

1
Setup the power foundation with the bed frame and slat base.
3Motion sensor installation
STEP 1: Connect the motion sensor connectors as illustrated.
HEAD BOARD
STEP 2: Use the double sided tape to secure the motion
sensor when necessary.
Take the bed out of the box, put it on the slat base, do not
install any
legs.
2Turn over the bed.
Uncoil the DC power cord .
HEAD BOARD
Control Box
DC Power Cord
motion sensor
extension cord
HEAD BOARD
Control Box

4Pull the DC power cord towards the direction of the AC power
source through either the bottom or the side of the bed frame.
Pull the two motion sensors to the two sides of the bed frame.
Make the bed completely flat
with a flipping motion .
DONE!
Insert the batteries into
the remote control.
HEAD BOARD
6Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply to the AC
power source.
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
5Install the mattress retainer bar one side after another.
HEAD BOARD
AC
Power Source
DC Power Cord
AAA AAA AAA
DC
Power Cord
HEAD BOARD
2
1

Immersive Audio System Installation
STEP 1: Lift the head and foot end of the bed by remote control. STEP 2: Pull the audio system cables and DC power cord toward the
direction of either bedstand through the bottom or the side of the bed frame.
WARNING — Ensure wires are below the metal frame and not between the
wood deck and metal frame.
Audio System Cable 2
Audio System Cable 3
Take out all the accessories from the immersive audio system box.
IMMERSIVE AUDIO SYSTEM BOX:
×1
AC Power Cord
×1
Power Supply of
Audio System
×1
Audio
Controller
×1
Immersive Audio
System Box
DC Power Cord
of Audio System
Audio System Cable 1

Audio System Cable 2
Audio System Cable 1
Audio System Cable 3
STEP 3: Plug the audio system cables into the audio controller.
STEP 4: Uncoil the AC power cord, Connect the DC power cord to the
power supply, and then connect the power supply to the AC power source.
STEP 5: Put the audio controller on the bedstand, the remote control can be
placed in the storage box of the audio controller.
AC Power Source
AC Power Cord
Power Supply
of Audio System
DC Power Cord
of Audio System

Electronics Quick Reference Guide
If simultaneous operation of two foundations is desired, please
follow the steps listed below.
Note the sync cord is needed to control two foundations with
mobile APP, follow the "Synchronizing Two Foundations with Sync
Cord" instruction to install the sync cord or follow the "Wireless
Syncing Instruction".
Head Motor
Foot Motor
Neck Motor Lumbar Motor
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
CB20B
Control Box
USB
Charger
DC
Power Cord
Power Supply
Motion Sensor
AC
Power Cord
Foot Massage
Motor(2 for King)
Head Massage
Motor(2 for King)
LED
Sync Plug
Sync Plug
Control Box 1
Control Box 2
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
HD Motor FT Motor Neck Motor LB Motor
HD Massage FT Massage
LED
SYNC MOTION
USB
VOICE
Sync Cord
Synchronizing Two Foundations with Sync Cord
STEP 1：Unplug foundations from the power source.
STEP 2：Connect the male ends of the sync cord to the female sync plugs of the control boxes
(Refer to below illustration).
STEP 3：Plug foundations back into the power source.
STEP 4：
Check to ensure all cords are securely attached.Either remote will operate both foundations
simultaneously.
Sync Cord
Remote Control
Press and hold and on both remotes at
the same time for 8 seconds,until the LCD
screen flashes and shows UNSYNC.
STEP 1：Make sure both remotes are individualy
paired to the foundation. If the remote is
not paired with the foundation, follow the
pairing instructions.
STEP 2：Make sure both foundations are at home
(flat position).
STEP 3：Press and hold and on both
remotes at the same time for 8 seconds
until the LCD screen shows SYNC.
Wireless Syncing Instruction
UN-SYNC Two Foundations
Press
and hold
Press
and hold