MotoSleep XFB User manual

OWNER’S MANUAL
LPB13WM Rev 9.0 07/2022
XFB/XSF Low Prof ile Bed
HOME SELECT
1
STOP
2
TV Z-G
SNORE

Setup the power foundation without the bed frame.
1Open the box lid.
HEAD BOARD
2
HOME SELECT
1
STOP
2
TV Z-G
SNORE
Take out all the accessories from the packaging and put
them aside. All electronics and components that need to
be installed are located in boxes under the foundation or
attached to the frame. Before discarding the packing
materials, ensure that all the parts are accounted for. ×1(2 for K/CK)
Mattress Retainer Bar
×1
Accessories Box
ACCESSORIES BOX:
×6
Adjustable Legs
×1
AC
Power Cord
×1
Remote
Control
×1
Power Supply with
Battery Backup Box
9V 9V
9V
(Optional)
×3
AAA
Batteries
AAA
×1
Sync Cord
（TXL/T/CKS Only）
Remove the red plastic safety lock before unfolding your power foundation.
3Remove the red plastic
safety clip.
Red Plastic
Safety Clip
Remove the folding locking
pin by pulling upwards.
Locking Pin
Turn the locking pin 90° in
counter clockwise direction.
Locking Pin

HEAD BOARD
DC Power Cord
Control Box
4Install 4 legs, make sure the
legs are tight.
HEAD BOARD
6Flip the foot end of the bed from the box and lay it
on top of the end at the headboard.
HEAD BOARD
7Install the remaining 2 legs on the foot end of the
bed, make sure the legs are tight.
Uncoil the DC power cord (connected to the control
box) and put it to the side of the bed.
HEAD BOARD
5Remove the bed from the box
with a flipping
motion, let the
bed stand on the 4 legs.

9bar one side after another.
Install the mattress retainer
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
HEAD BOARD
10 Uncoil the AC power cord, connect
the DC power cord to the power
supply and then connect the
power supply to the AC
power source.
DONE!
2
1
8Make the bed completely flat.
HEAD BOARD
the remote control.
Insert the batteries into
AAA AAA AAA
HOME SELECT
1
STOP
2
TV Z-G
SNORE

Insert the batteries into
the remote control.
1
HEAD BOARD
2Make the bed completely flat
with a flipping motion .
3Install the mattress retainer bar one side after another.
HEAD BOARD
4Uncoil the AC power cord, connect the DC power cord to the
power supply and then connect the power supply to the AC
power source.
Setup the power foundation with the bed frame and slat base.
AC Power Cord
AC Power Source
DC Power Cord
Power Supply
HEAD BOARD
AC
Power Source
DC Power Cord
DC Power Cord
DC
Power Cord
HEAD BOARD
2
1
HOME SELECT
1
STOP
2
TV Z-G
SNORE
Take the bed out of the box, put it on the slat base , do not install
any legs. Uncoil the DC power cord (connected to the control box)，
pull the DC power cord towards the direction of the AC power source
through either the bottom or the side of the bed frame.
AAA AAA AAA
DONE!

HOME SELECT
1
STOP
2
TV Z-G
SNORE
HOME SELECT
1
STOP
2
TV Z-G
SNORE
HOME SELECT
1
STOP
2
TV Z-G
SNORE
Remote
Control
Sync Plug
Sync Plug
Control Box 1 Control Box 2
Sync Cord
HD Motor FT Motor Neck Motor
HD Massage FT Massage
LED PROG APP SYN
USB
Power
HD Motor FT Motor Neck Motor
HD Massage FT Massage
LED PROG APP SYN
USB
Power
Electronics Quick Reference Guide
If simultaneous operation of two foundations is
desired, please follow the steps listed below.
Sync cable is not required if both
adjustable bases are equipped with
V2.0 or newer remote controls. If the
bases are equipped with V2.0 remote controls, follow
the “Wireless Syncing Instruction”.
If the adjustable bases are not equipped with V2.0 on
newer remote controls, follow the “Synchronizing
Two Foundation with Sync Cord” instruction.
Wireless Syncing Instruction
UN-SYNC Two Foundations
Press and hold and on both remotes at the
same time for 5 seconds,until the LCD screen
flashes and shows UN-SYNC.
STEP 1：Make sure both remotes are individualy
paired to the foundation. If the remote is
not paired with the foundation, follow the
pairing instructions.
STEP 2：Make sure both foundations are at home
(flat position).
STEP 3：Press and hold and HOME on both
remotes at the same time for 5 seconds
until the LCD screen shows SYNC.
Press
and hold
Press
and hold
Synchronizing Two Foundations with Sync Cord
STEP 1：Unplug foundations from the power source.
STEP 2：Connect the male ends of the sync cord to the female sync plugs of the control boxes
(Refer to below illustration).
STEP 3：Plug foundations back into the power source.
STEP 4：
Check to ensure all cords are securely attached.Either remote will operate both
foundations simultaneously.
Model No.:******
****** V2.0
USB
Charger
Head Motor Foot Motor
Neck Motor
DC
Power Cord
Power Supply
AC
Power Cord
HD Motor FT Motor Neck Motor
HD Massage FT Massage
LED PROG APP SYNUSBPower
LED
CB18
Control Box
WIRELESS RECEIVER
Foot Massage
Motor(2 for King)
Head Massage
Motor(2 for King)
Sync Cord

Pairing Remote
Setting Programmable Position
Setting Remote Lock
The LCD screen will show LOW once the batteries are in low power.
LOCK
UNLOCK
LOW BATTERY
Make sure the batteries are good. Replace
them when needed.
Plug the power cord back into the power source. You will hear an activation
sound in 2 seconds, indicating the remote is paired to the power foundation.
Unplug the power cord from the power source. If 9V backup batteries
were installed in the power supply, remove them.
Adjust the head, foot and neck to your desired position.
To adjust a saved position, repeat step 1 and 2 and the new position
will be saved.
Press and hold the program button for about 5 seconds until the
LCD screen shows SAVE, and press picture programmable buttons
until you hear 2 beep sounds.
1 2
Press and hold Select button until the LCD screen of the remote
control shows PAIR.
Press and hold the HOME and SELECT buttons simultaneously for about
5 seconds until the LCD screen shows LOCK.
Press and hold the HOME and SELECT buttons for about 5 seconds until
the LOCK disappears on the LCD screen.
STEP 1：
STEP 2：
STEP 3：
STEP 1：
STEP 2：
STEP 3：
STEP 4：
HOME SELECT
1
STOP
2
TV Z-G
SNORE
Remote Control Instructions
ADJUST
This button lifts the Head/Foot/
Neck section of the foundation.
This button lowers the Head/Foot/
Neck section of the foundation.
One touch programmable positions.
2
1
SETTING PROGRAMMABLE POSITION
MASSAGE FEATURES
Turn on the head massage. Cycle
through 3 massage intensities.
Turn off the head/foot massage.
STOP
Turn on the foot massage. Cycle
through 3 massage intensities.
Lifts
Lowers
Program
Select Zone
TV Position
Home Position
Foot Massage on
（3 Intensity Levels）
Head Massage on
（3 Intensity Levels）
Zero G Preset
Position
Programmable
Positions
Anti-Snore
Preset Position
Head/Foot
Massage off
HOME SELECT
1
STOP
2
TV Z-G
SNORE
Under Bed
LED on/off
ONE TOUCH BUTTON
One touch flat position.
One touch Select button.Select
head or foot zone.
One touch ANTI-SNORE preset
position.
SNORE
One touch TV preset position.
TV
One touch ZERO G preset
position. ZERO G adjusts your
legs to a higher level than your
heart, helping to relieve pressure
of the lower back and promote
circulation.
Z-G
One touch underneath LED
lighting on/off.
AAA AAA
AAA
The original remote that comes in the box is already
paired to the foundation. No further action is required.
In the event when the remote is not paired with the
foundation, follow the pairing instructions below.

MotoSleep Mobile APP（Optional）
GET
+INSTALL
Before you start. Switch on the pairing function on your mobile device. Make sure your
MotoSleep Power Foundation is correctly connected and is power-on.
The MotoSleep APP will automatically pair your MotoSleep Power Foundation once you start
the APP and does not require additional settings.
www.motosleep.com
REMOTECONTROL
REMOTECONTROL
HEAD FOOT
REMOTECONTROL
REMOTECONTROL
1
STOP
2
REMOTECONTROL
1 2
TV Z-G
SNORE
REMOTECONTROL
2
1
STOP
REMOTECONTROL
SNORE
TV Z-G
2
1
REMOTECONTROL
1
STOP
2
TV Z-G
SNORE
OWNER’S MANUAL
Four-button Remote Control Three-button Remote Control
Five-button Remote Control
Eleven-button Remote Control
Eleven-button Remote Control
Ten-button Remote Control
Ten-button Remote Control
Thirteen-button Remote Control
Thank you for purchasing a MotoSleep
Power Foundation.
REMOTE CONTROL
1
2
8
3
5
4
6 7
9 10 11
12 14 13
1
STOP
2
TV Z-G
SNORE
1
11
12
13
14
10
9
8
7
5
4
3
2
6
Enter the Settings Page
Select Head,Foot or Neck section
Lifting function
Lowering function
One Touch flat position
Head Massage (3 different intensities)
Foot Massage (3 different intensities)
Massage Off Button
Programmable Position 1
Programmable Position 2
Under Bed Lighting
Anti-Snore Preset Position
TV Position
Zero G Preset Position
* The effective connection range is ± 10m
8
7
6
5
4
3
2
1
List of MotoSleep Products within
the connection range*
Tap the Refresh Button to refresh
the MotoSleep Products List
Enter the Settings Page
Back to the Home Screen
9
Serial Number of the control box
Owner’s Manual Page
Troubleshooting
Disconnect from the paired
MotoSleep Product
Rename your MotoSleep Power
Foundation of your choice
Home Screen
Settings Page
9
SELECT DEVICE
BED
Refresh
3
1
2
SETTINGS
DISCONNECT
Serial Number
5
4
RENAME
OWNER’S MANUAL
6
7
TROUBLESHOOTING
8
MotoSleep Mobile APP is a mobile application to control the MotoSleep Power Foundation with
mobile devices. The application is available for both iOS and Android based smart devices.
The MotoSleep Mobile APP uses the latest technology to communicate with your MotoSleep
Power Foundation. Make sure your mobile devices has the pairing function for the APP to
work correctly.

HEAD BOARD
Lift the head and foot end of the bed by remote control. Install four stabilizer
brackets as shown. Use a phillips screwdriver and socket wrench to tighten
the screws and bolts.
Screws
ST4.2×16
M8*16 Bolts
Washers
Headboard Bracket Installation Guide (Optional)
Headboard brackets are optional and not included. A 1/2” (13 mm)
socket and 1/2” (13 mm) wrench are required to complete the installation.
12
2
1
a)Align the slot hole of the headboard bracket to the sleeve into
which the leg threads. DO NOT OVERTIGHTEN. Too much force
may damage the thread.
b)The headboard bracket has 2 adjustable slots to accommodate
any frame type. Use the bolts and washers to secure the bracket.
Make sure the bolts are tight.
a)To put the T-Bracket and Headboard Bracket together, you will
need (2) M8×16 bolts and (2) nuts. Slip the bolts through the holes
from T-Bracket to Headboard Bracket with the head of bolt facing
outward. Use the 1/2” (13 mm) socket and 1/2” (13mm) wrench to
tighten the bolts.
You may now connect your headboard to the attachment plates using the remaining short bolts
and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2” (13mm)
socket and 1/2” (13mm) wrench to tighten the bolts.
(2) Headboard Brackets (2) T-Brackets (8) M8*16 (4) Nuts (4) Washers
Slat Pack Installation Guide (Optional)
Stabilizer Brackets are optional and not included. They can fix the
bed onto the slat base. A phillips screwdriver and socket wrench are
required to complete the installation.
(4) Stabilizer Brackets (1) Socket Wrench(8) Screws ST4.2×16 (8) Bolts M8*16 (8) Washers
STABILIZER BRACKETS COMPONENTS
Support leg may be needed on some slat/platform bed frames, refer
to the leg configuration table for height adjustment.
* Make sure the adjustable legs are properly tight, and the plastic caps have been placed at
the bottom of the legs. Incorrect installation might cause the part to fail or damage the floor.
OPTIONAL EQUIPMENT/PART (NOT INCLUDED)
Socket and Wrench 1/2'' (13mm)
(6)
SLAT/ PLATFORM
LEGS
Leg
Configuration
Leg Height
Leg Configuration Table
4 " 7⁵⁄8 " 11³⁄8 " 16¹⁄2 "
5 ¹⁄8 "
(Optional)
×6
Included in
Accessories Box
(See Page 2
for details)

Customer Service Toll Free:1-844-696-6886
Install two spacing connectors to ensure the gap between the two adjustable bases is consistent.
Spacing Connector for TXL/T/CKS (Optional)
(2) SPACING CONNECTOR (TXL/T/CKS ONLY)
Lift the head and foot end of the bed by remote control. Install the spacing connector as shown.
Spacing
Connector
Bed Frame
Bed Frame
PRODUCT PROTECTED BY FOLLOWING PATENT:
— US PATENT: 10, 306, 994