Moultrie Pro Hunter User manual

Turn Drum upside down.
Metal
Drum
Funnel
Short
Bolts
Funnel placement will vary based on the
construction of Drum. When using a metal
Drum, place Funnel inside Drum with small
end of funnel facing down, and attach with
provided Short Bolts, nuts and washers.
When using a plastic Drum, the funnel may need
to be mounted on the outside. Select the funnel
placement based on the ability to have a 1/2” to
5/8” gap between the bottom of the Funnel and
the horizontal section (center) of the Spinner
Plate as shown below.
Place Feeder on Drum.
Attach Feeder Legs to Drum as
shown with Bolts using nuts and
washers provided.
Feeder Leg Holes
Turn drum over, measure and mark the center of the bottom.
Center the provided template on the bottom of the drum
and secure with tape. Drill two 3/16" Funnel Holes and
three 5/16" Feeder Leg Holes.
Using a Hole Saw, drill a 2-1/4" hole in the center of the
bottom of your drum.
CAUTION: WEAR EYE PROTECTION
THANK YOU for your purchase of the Pro Hunter Feeder Kit.
Please read this sheet before operating the unit. If you should have
any questions about this product or any other Moultrie product,
please contact us using the information on the back of this sheet. To
help us to better serve you, please complete and mail the enclosed
Warranty Card.
DRILLING YOUR DRUM/BARREL/BUCKET
MOUNTING THE FEEDER
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna  Increase the separation between the equipment and the receiver
Pro Hunter will mount to the bottom of any drum or bucket Funnel Holes
Instructions for Pro Hunter Feeder Kit
Drum
Feeder Legs
Feeder
Bottom of Funnel
Horizontal section
of Spinner Plate
1/2” to 5/8” gap

SET
UP DOWN
SET
UP DOWN
SET
UP DOWN
01212010R5 / MFH-PHBK
1: (Q) What battery should I use? (A) For best performance, use a
rechargeable 6-Volt, 5 Amp-Hour Moultrie brand battery. If
disposable batteries will be used, EnergizerTM Alakaline batteries are
recommended.
2: (Q) What should I do if the timer isn't working? (A) Check the
connections to the battery to make sure alligator clips have not come
loose. Then check the battery itself by changing to a known good
battery. If the problem still persists, call Moultrie Customer Service
at the number below.
Remove bottom and install a 6-Volt Alkaline
(ex. EnergizerTM), Moultrie rechargeable
6-Volt battery, or four Alkaline D Cell
Batteries using the provided adapter. Connect
the Red Alligator Clip to the positive terminal
(+) and the Black Alligator Clip to the
negative (-) terminal.
CAUTION: WEAR EYE PROTECTION
CONFIGURING AND TESTING FEEDER
INSTALLING BATTERY
SET TIME OF DAY: Press the UP or DOWN button until the correct time of day appears.
Press and release button to single-step through the minutes or hold down to advance quickly.
The feeder will not run while buttons are being pressed and waits 10 seconds from the last
button press before it is activated. The feeder is activated when the display alternates between
the CURRENT TIME and %BATTERY.
SET FEED TIMES: Press the SET button until the
correct Timer Number appears in the upper right hand
corner as shown. Press the UP or DOWN button to set
the Feed Time.
SET RUN DURATION: Press the SET button again
to set the RUN-TIME SECONDS which can range
from zero to twenty seconds. Adjust RUN-TIME
SECONDS using the chart below. Set the RUN-TIME
SECONDS to zero to disable the specific timer.
TEST TIMER: To test the Timer, PRESS AND HOLD
the SET button while the RUN-TIME SECONDS are
displayed. Release the button and get away from the
feeder when the message “TESTING GET AWAY”
appears on the display. The display will countdown five
seconds before activating the motor for the number of
RUN-TIME SECONDS programmed. The test feature is
useful for assessing the amount of feed to dispense.
Your Pro Hunter will feed up to six times per day and has been factory set to feed at 7:00am and
6:00pm for six seconds. To change the factory settings or add additional feed times, follow the
instructions below. The Battery Level is displayed every seven seconds. It is recommended that the
battery be replaced when the %BATTERY reading is 25% or below.
8:00
SET TIMER
3
AM
:06
SET TIMER
3
RUN-TIME
SECONDS
:05
TESTING GET AWAY
RUN TIME (sec.)
Approx. feed dispensed (lbs.)
4 6 8 10 12 14 16 18
.75 1 1.5 2 2.5 3 3.5 4
Our Service Department will gladly answer any questions you have. Call
205-664-6700 or 800-653-3334, Monday - Friday, 8:00 AM to 5:00 PM CST.
www.moultriefeeders.com
- OR -
6-Volt Alkaline
Four Alkaline D
Cells using
provided adapter
Feeder with D
Cell adapter