Moxa Technologies DRP Series User manual

P/N: 1802001004010
*1802001004010*
DRP Series
Quick Installation Guide
Version 1.0, September 2023
Technical Support Contact Information
www.moxa.com/support

2023 Moxa Inc. All rights reserved.

- 2 -
Overview
The DRP series DIN-rail computers are powered by an Intel Atom®,
Intel® Celeron®, or Intel® Core™ i5/i7 processor. The computers
come with a rich set of interface options including up to 8 software-
selectable RS-232/422/485 serial ports and up to 10 gigabit Ethernet
ports. The communication interfaces are located on the front and rear
sides of the product, enabling easy access and expansion for industrial
applications. A dual-storage design that includes CFast and SD slots
enables easy storage expansion. The unique battery fastener cover
design for the battery slot secures the battery in place and ensures
stability in all operating environments.
Designed as compact fanless computers with operating temperature
range of -30 to 60°C and built-in TPM 2.0 module, the DRP computers
are ideal as reliable and secure computing platforms for both IT/ OT
applications in extreme operating environments.
Package Checklist
Before installing the DRP Series, verify that the package contains the
following items:
•DRP Series computer with DIN-rail kit
•2-pin terminal block for DC power
•Quick installation guide (printed)
•Warranty card
NOTE
Please notify your sales representative if any of the above
items are missing or damaged.
Panel Layouts
The panel layouts of the DRP series computers are shown in the
following illustrations:
DRP-C100-C1-T/DRP-C100-C5-T/DRP-C100-C7-T Models
Front View

- 3 -
Top View
Bottom View
DRP-C100-C1-8L-T/DRP-C100-C5-8L-T/DRP-C100-C7-8L-T Models
Front View
Top View
Bottom View

- 4 -
DRP-C100-C1-6C-T/DRP-C100-C5-6C-T/DRP-C100-C7-6C-T Models
Front View
Top View
Bottom View

- 5 -
DRP-C100-C1-2L4C-T/DRP-C100-C5-2L4C-T/DRP-C100-C7-2L4C-T Models
Front View
Top View
Bottom View

- 6 -
DRP-A100-E2-T/DRP-A100-E4-T Models
Front View
Top View
Bottom View

- 7 -
DRP-A100-E2-8L-T/DRP-A100-E4-8L-T Models
Front View
Top View
Bottom View

- 8 -
DRP-A100-E2-6C-T/DRP-A100-E4-6C-T Models
Front View
Top View
Bottom View

- 9 -
DRP-A100-E2-2L4C-T/DRP-A100-E4-2L4C-T Models
Front View
Top View
Bottom View

- 10 -
Dimensions
DRP-C100-C1-T/DRP-C100-C5-T/DRP-C100-C7-T/DRP-A100-E2-T/DRP-
A100-E4-T Models
DRP-C100-C1-8L-T/DRP-C100-C5-8L-T/DRP-C100-C7-8L-T/DRP-A100-E2-
8L-T/DRP-A100-E4-8L-T Models

- 11 -
DRP-C100-C1-6C-T/DRP-C100-C5-6C-T/DRP-C100-C7-6C-T/DRP-A100-E2-
6C-T/DRP-A100-E4-6C-T Models
DRP-C100-C1-2L4C-T/DRP-C100-C5-2L4C-T/DRP-C100-C7-2L4C-T/DRP-
A100-E2-2L4C-T/DRP-A100-E4-2L4C-T Models

- 12 -
LED Indicators
The following table describes the LED indicators located on the front
panel of the DRP Series:
LED Name
Status
Function
Power
Green
Power is ON
OFF
No power input or any other power error
Ethernet
(10/100
Mbps)
(1000 Mbps)
Green
Steady ON: 10/100 Mbps Ethernet link
Blinking: Data is being transmitted or
received
Yellow
Steady ON: 1000 Mbps Ethernet link
Blinking: Data is being transmitted or
received
OFF
No Ethernet connection
Storage
(CFast)
Yellow Blinking: Data is being accessed from
the
CFast card
OFF Data is not being accessed from the
CFast card
Installing the DRP Computer
DIN-rail Mounting
The DRP computers come with a DIN-rail mounting kit. To install the
DIN-rail mounting kit, do the following:
STEP 1:
Check the
DIN-rail
mounting
kit that comes
preinstalled
on the rear
panel of the DRP
computers
.
STEP 2:
Insert the top of the DIN
rail into the slot just below
the upper hook of the DIN
-
rail mounting kit
.
S
TEP 3:
Press the
DRP computer
t
owards the DIN rail until
the mounting kit
snaps into
place.

- 13 -
Removal:
STEP 1:
Pull down the latch on the
mounting kit with a
screwdriver.
STEP 2 & 3
:
Slightly pull the
DRP Series
forward and li
ft it up to
remove it from the DIN
rail.
The specifications of the
DIN
-rail mounting screws
are indicated in the
i
llustration on the right.
A
dhere to these values if
you need to buy
replacement screws to
attach and secure the
DIN
-rail bracket to the
rea
r panel of the
computer.
NOTE
This computer is intended to be installed only in an area with
restricted access. In addition, for safety reasons, the computer
should be installed and handled only by qualified and
experienced professionals.
Connecting the Power
The DRP computers are provided with 2-pin power input connectors in a
terminal block on the front panel. Insert the power-cord wires into the
connectors and tighten them to secure the wires in place. Plug in the
power cable to a power source. The power LED will light up to indicate
that power is being supplied to the computer. It should take about 30
to 60 seconds for the operating system to complete the boot-up
process.
Pin
Definition
1
V+
2
V-

- 14 -
ATTENTION
This product is intended to be supplied by a
Listed Power
Supply with output marked LPS and rated to deliver
the
following power specifications:
DRP
-C100:12 VDC (max.) @ 6.82A, 24 VDC (max.) @ 3.25A
DRP
-A100: 12 VDC (max.) @ 5A, 24 VDC (max.) @ 2.5A
and
a minimum Tma=60˚C. If you need assistance with
purchasing a power adapter, contact the Moxa technical
support team.
ATTENTION
Before connecting the
DRP computer to the DC power input,
ensure that
the DC power source voltage is stable.
•
The wiring for the input terminal block must
be installed by
qualified and experienced professionals.
•Wire Type: Cu
•Use 18-12 AWG wire size and a torque value of 0.5
N-m
•
Use only one conductor in a clamping
point between the DC
power source and the power input.
NOTE
If using Class I adapter, the power cord adapter should be
connected to a socket outlet with an earthing connection or the
power cord and adapter must comply with Class II construction.
NOTE
For surge protection, connect the grounding connector located
below the power connector with the earth (ground) or a metal
surface.
A 4 mm
2 conductor must be used when the connection to the
external grounding screw is utilized. The heat sink is grounded
to the chassis by an internal screw.
Warning
為避免電磁干擾，本產品不應安裝或使用於住宅環境。
Connecting Displays
The DRP computer comes with a VGA and a HDIM display output
located on the front panel for connecting to audio or video devices.
NOTE
U
se an HDMI-certified cables for a reliable audio or video
connection.

- 15 -
Communications Connections
Ethernet Ports
The 10/100/1000 Mbps Ethernet ports use RJ45 connectors.
Pin
10/100 Mbps
1000 Mbps
1
ETx+
TRD(0)+
2
ETx-
TRD(0)-
3
ERx+
TRD(1)+
4
–
TRD(2)+
5
–
TRD(2)-
6
ERx-
TRD(1)-
7
–
TRD(3)+
8
–
TRD(3)-
NOTE
For reliable Ethernet connections, we recommend enabling the
ports in standard temperatures and keeping them enabled in
high/low temperature environment.
Serial Ports
The serial ports use DB9 connectors. Each port can be configured by
software as a RS-232, RS-422, or RS-485 port. The pin assignments for
the ports are shown below:
Pin RS-232 RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
TxDA(-)
TxDA(-)
–
2
RxD
TxDB(+)
TxDB(+)
–
3
TxD
RxDB(+)
RxDB(+)
DataB(+)
4
DTR
RxDA(-)
RxDA(-)
DataA(-)
5
GND
GND
GND
GND
6
DSR
–
–
–
7
RTS
–
–
–
8
CTS
–
–
–
USB Hosts
The DRP Series has 3 USB 3.0 Type-A connectors located on the front
panel. The ports support keyboard and mouse devices and can also be
used to connect a flash disk for storing large amounts of data.
Inserting SD/CFast Card
The DRP computer comes with two slots that allow users to insert one
SD card and one CFast card. To install the cards, do the following:
1. Unfasten the two screws on the slot cover.

- 16 -
2. Remove the cover and find
the location of the SD and
CFast card slots.
3. Insert the SD and CFast cards in the designated slots.
Refer to the image printed beside the slots for the correct direction
to insert the cards. When the cards are successfully inserted, you
will hear a click.
4. To remove the cards, simply push them in to release them and take
them out.
Replacing the Battery
The DRP computer comes with one slot for a battery on the bottom
panel of the computer. A lithium battery (3 V / 200 mAh) is preinstalled
in the slot.
To replace the battery, do the following:
1. Unfasten the two screws on the battery cover.
2. Take off the cover.
The battery is attached to the slot cover as indicated in the image.
3. Unplug the connector of the battery-cover assembly from the
internal wire of the slot.
4. Remove the two screws on the metal plate attached to the battery
holder.

- 17 -
5. Place a new battery in the battery holder, replace the metal plate,
and fasten the two screws on to the frame to secure the battery.
6. Plug in the connector of the battery-cover assembly to the internal
wire of the slot.
7. Place the battery holder back in the slot and secure it by fastening
the two screws on the cover.
Warning
•
Be sure to use the correct type of battery. Incorrect
battery may cause system damage. Contact Moxa’s
technical support staff for assistance, if necessary.
•
To reduce the risk of fire or burns, do not disassemble,
crush, or puncture the battery; do not dispose of in fire or
water and do not short external contacts.

- 18 -
限用物質含有情況標示聲明書
DRP-C100-C1-T
DRP-C100-C1-T-Win10
DRP-C100-C5-T
DRP-C100-C5-T-Win10
DRP-C100-C7-T
DRP-C100-C7-T-Win10
DRP-C100-C1-8L-T
DRP-C100-C5-8L-T
DRP-C100-C7-8L-T
DRP-C100-C1-6C-T
DRP-C100-C5-6C-T
DRP-C100-C7-6C-T
DRP-C100-C1-2L4C-T
DRP-C100-C5-2L4C-T
DRP-C100-C7-2L4C-T
DRP-A100-E2-T
DRP-A100-E2-T-Win10
DRP-A100-E4-T
DRP-A100-E4-T-Win10
DRP-A100-E2-8L-T
DRP-A100-E4-8L-T
DRP-A100-E2-6C-T
DRP-A100-E4-6C-T
DRP-A100-E2-2L4C-T
DRP-A100-E4-2L4C-T