Moxa Technologies MGate 5109 User manual

MGate 5109 User’s Manual
Edition 2.2, March 2018
www.moxa.com/product
© 2018 Moxa Inc. All rights reserved.

MGate 5109 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in accordance with
the terms of that agreement.
Copyright Notice
© 2018 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the part of
Moxa.
Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited
to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the
products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for
its use, or for any infringements on the rights of third parties that may result from its use.
This product might include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the publication.
Technical Support Contact Information
www.moxa.com/support
Moxa Americas
Toll
-free: 1-888-669-2872
Tel:
[phone]
Fax:
[phone]
Moxa Chi
na (Shanghai office)
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe
Tel:
[phone]
Fax: [phone]
Moxa Asia
-Pacific
Tel:
[phone]
Fax: [phone]
Moxa India
Tel:
[phone]
Fax:
[phone]

Table of Contents
1. Introduction...................................................................................................................................... 1-1
Overview ...........................................................................................................................................1-2
Package Checklist ............................................................................................................................... 1-2
Product Features ................................................................................................................................ 1-2
2. Hardware .......................................................................................................................................... 2-1
Power Input and Relay Output Pinouts................................................................................................... 2-2
LED Indicators....................................................................................................................................2-2
Dimensions ........................................................................................................................................2-3
Pin Assignments .................................................................................................................................2-3
Mounting the Unit ...............................................................................................................................2-4
Specifications .....................................................................................................................................2-5
Reset Button ......................................................................................................................................2-7
Pull-high, Pull-low, and Terminator for RS-485 .......................................................................................2-7
MicroSD.............................................................................................................................................2-8
3. Getting Started.................................................................................................................................. 3-1
Connecting the Power .........................................................................................................................3-2
Connecting Serial Devices....................................................................................................................3-2
Connecting to a Network ..................................................................................................................... 3-2
Installing DSU Software.......................................................................................................................3-2
Logging in to the Web Console .............................................................................................................3-3
Quick Setup .......................................................................................................................................3-4
Quick Setup—System Setting........................................................................................................3-4
Quick Setup—Select Protocol ........................................................................................................3-5
4. Web Console Configuration and Troubleshooting.............................................................................. 4-1
Overview ...........................................................................................................................................4-2
Basic Settings ....................................................................................................................................4-2
Network Settings ................................................................................................................................ 4-3
Serial Settings....................................................................................................................................4-3
Protocol Settings (Agent Mode) ............................................................................................................4-4
Protocol Settings—Protocol Conversion ..........................................................................................4-5
Protocol Settings—Configure MGate’s Role 1 and Role 2 ...................................................................4-6
Protocol Settings (Transparent Mode).................................................................................................. 4-27
Modbus Transparent .................................................................................................................. 4-27
Protocol Settings—Modbus Transparent—Mode ............................................................................. 4-28
Protocol Settings—Modbus Transparent—Slave ID Map .................................................................. 4-29
Protocol Settings—Modbus Transparent—Priority Control................................................................ 4-31
Protocol Settings—Modbus Transparent—Advanced Settings ........................................................... 4-31
DNP3 Transparent ..................................................................................................................... 4-32
Protocol Settings—DNP3 Transparent—Advanced Settings .............................................................. 4-34
System Management......................................................................................................................... 4-34
System Management—Accessible IP List....................................................................................... 4-34
System Management—DoS Defense ............................................................................................ 4-35
System Management—System Log Settings.................................................................................. 4-35
System Management—Auto Warning Settings ............................................................................... 4-36
System Management—Email Alert ............................................................................................... 4-37
System Management—SNMP Trap ............................................................................................... 4-37
System Management—SNMP Agent ............................................................................................. 4-38
System Management—LLDP Settings ........................................................................................... 4-39
System Management—Certificate ................................................................................................ 4-39
System Management—Misc. Settings ........................................................................................... 4-40
System Management—Maintenance ............................................................................................. 4-42
System Monitoring (Troubleshooting) .................................................................................................. 4-44
System Monitoring—System Status ............................................................................................. 4-44
System Monitoring—Protocol Status............................................................................................. 4-45
Status Monitoring ............................................................................................................................. 4-50
5. Configuration (Text Mode Console) ................................................................................................... 5-1
6. Network Management Tool (MXstudio) ............................................................................................. 6-1
Overview ...........................................................................................................................................6-2

1
1. Introduction
Welcome to the MGate 5109 line of Modbus-to-DNP3 gateways. All models feature easy protocol conversion
between Modbus RTU/ASCII, Modbus TCP, and DNP3 protocols. This chapter is an introduction to the MGate
5109.
The following topics are covered in this chapter:

Overview

Package Checklist

Product Features

MGate 5109 Introduction
1-2
Overview
The MGate 5109 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP and DNP3 serial/TCP/UDP
protocol conversion. All models are protected with a rugged metallic casing, DIN-rail mountable, and offer
built-in serial isolation. The rugged design is suitable for industrial applications such as oil/gas, power, process
automation, and factory automation.
Package Checklist
All models of the MGate 5109 series are shipped with the following items:
Standard Accessories:
•1 MGate 5109 gateway
•1 serial cable: DBL-RJ45F9-150
•Documentation and software CD
•Quick installation guide (printed)
•Warranty card
Please notify your sales representative if any of the above items are missing or damaged.
Optional Accessories (can be purchased separately)
•CBL-F9M9-150: DB9-female-to-DB9-male serial cable, 150 cm
•CBL-F9M9-20: DB9-female-to-DB9-male serial cable, 20 cm
•CBL-RJ45SF9-150: RJ45-to-DB9-female shielded serial cable, 150 cm
•ADP-RJ458P-DB9F: DB9-female-to-RJ45 connector
•ADP-RJ458P-DB9F-ABC01: DB9-female-to-RJ45 connector
•Mini DB9F-to-TB: DB9-female-to-terminal-block connector
Product Features
•Gateway function to transfer data between Modbus RTU/ASCII/TCP and DNP3 serial/TCP/UDP
•Support for both DNP3 master and outstation
•Up to 31 Modbus serial slaves or DNP3 serial outstations
•Up to 32 Modbus TCP slaves or DNP3 TCP/UDP outstations
•Support DNP 3.0 subset level 2
•DNP3 master mode support up to 18800 points
•Effortless configuration via Web console
•Complete packet analysis and diagnosis information for maintenance
•Redundant dual DC power inputs and relay output supported
•MicroSD card supported for configuration backup
•-40 to 75°C wide operating temperature range models available
•Serial port with 2 kV built-in isolation protection
•Built-in Ethernet cascading for easy wiring

2
2. Hardware
The following topics are covered in this chapter:

Power Input and Relay Output Pinouts

LED Indicators

Dimensions

Pin Assignments

Mounting the Unit

Specifications

Reset Button

Pull-high, Pull-low, and Terminator for RS-485

MicroSD

MGate 5109 Hardware
2-2
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC Power
Input 2
DC Power
Input 2 N.O. Common N.C. DC Power Input 1
DC Power
Input 1
LED Indicators
Agent Mode:
LED Color Description
Ready Off Power is off or a fault condition exists
Green
Steady: Power is on, and the MGate is functioning normally
Red Steady: Power is on, and the MGate is booting up
Blinking slowly: Indicates an IP conflict, or the DHCP or BOOTP server is not
responding properly
Flashing quickly: microSD card failed
MB*
Off
No serial communication with Modbus device
Green Normal Modbus serial communication in progress
Red Serial communication error
When MGate 5109 acts as Modbus Master:
1. Slave device returned an error (exception)
2. Received frame error (parity error, checksum error)
3. Timeout (slave device no response)
When MGate 5109 acts as Modbus Slave:
1. Received invalid function code
2. Master accessed invalid register addresses or coil addresses
3. Received frame error (parity error, checksum error)
DNP3* Off No serial communication with DNP3 device
Green Normal DNP3 serial communication in progress
Red Serial communication error
When MGate 5109 acts as DNP3 Master:
1. Received outstation exception (format error, checksum error, invalid data,
outstation responds not support)
2. Timeout (outstation no response)
When MGate 5109 acts as DNP3 outstation:
1. Received master exception (format error, checksum error, invalid data)
2. Timeout (master no response)
*Only indicates serial communication status; for Ethernet status, refer to the LED indicator on the Ethernet
port.

MGate 5109 Hardware
2-3
Transparent Mode:
LED Color Description
Ready Off Power is off, or a fault condition exists
Green Steady: Power is on, and the MGate is functioning normally
Red Steady: Power is on, and the MGate is booting up
Blinking slowly: Indicates an IP conflict, or the DHCP or BOOTP server is not
responding properly
Flashing quickly: microSD card failed
MB Off No communication with Modbus device
Green Modbus communication in progress**
DNP3 Off No communication with DNP3 device
Green DNP3 communication in progress**
**The LED will light up (green) only during the period when the MGate is receiving data on a serial port (Rx);
this does not include transmitted data (Tx).
Dimensions
Unit: mm (inch)
Pin Assignments
Serial Port (Male DB9)
Pin RS-232 RS-422/RS-485 (4W) RS-485 (2W)
1 DCD TxD-(A) –
2
RXD
TxD+(B)
–
3 TXD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5* GND GND GND
6 DSR – –
7 RTS – –
8 CTS – –
9 – – –
*Signal ground

MGate 5109 Hardware
2-4
Ethernet Port (RJ45)
Pin Signal
1 Tx+
2 Tx-
3 Rx+
6 Rx-
Console Port (RS-232)
The MGate 5109 series can use an RJ45 serial port to connect to a PC for device configuration.
Pin RS-232
1 DSR
2 RTS
3 GND
4 TXD
5 RXD
6 DCD
7
CTS
8 DTR
Mounting the Unit
1. Connect the power adapter. Connect the 12-48 VDC power line or DIN-rail power supply to the MGate
5109’s terminal block.
2. Use a serial cable to connect the MGate to the Modbus or DNP3 device.
3. Use an Ethernet cable to connect the MGate to the Modbus or DNP3 device.
4. The MGate 5109 is designed to be attached to a DIN rail or mounted on a wall. For DIN-rail mounting, push
down the spring and properly attach it to the DIN rail until it snaps into place. For wall mounting, install the
wall-mounting kit (optional) first and then screw the device onto the wall.
The following figure illustrates the two mounting options:

MGate 5109 Hardware
2-5
Specifications
Ethernet Interface
Protocols:
Modbus TCP client/server, DNP 3.0 TCP/UDP master/outstation
Number of Ports:
2 (1 IP, Ethernet cascade)
Speed:
10/100 Mbps, Auto MDI/MDIX
Connector:
8-pin RJ45
Magnetic Isolation Protection:
1.5 kV (built-in)
Serial Interface
Protocols:
Modbus RTU/ASCII master/slave, DNP 3.0 serial master/outstation
Number of Ports:
1
Serial Standards: RS-232/422/485, software selectable
Connectors:
DB9 male
RS
-485 Data Direction Control: ADDC® (automatic data direction control)
Pull High/Low Resistor for RS
-485: 1 kΩ, 150 kΩ
Terminator for RS
-485: 120 Ω
Isolation:
2 kV (built-in)
Serial Communication Parameters
Data Bits:
7, 8
Stop Bits:
1, 2
Parity:
None, Even, Odd, Space, Mark
Flow Control:
RTS/CTS, RTS Toggle (RS-232 only)
Baudrate:
50 bps to 921.6 kbps
Serial Signals
RS
-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS
-422: Tx+, Tx-, Rx+, Rx-, GND
RS
-485-4w: Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w: Data+, Data-, GND
Modbus
Functions Supported:
1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Commands:
100
Max. No. of Connections:
MGate
as Modbus TCP Master: 32 slave connections
MGate as Modbus TCP slave: 16 master connections

MGate 5109 Hardware
2-6
DNP3
Max. No. of Connections:
• Transparent mode:
16 DNP3 TCP master connections or 32 DNP3 TCP outstation connections
• Agent mode:
MGate as DNP3 TCP/UDP master: 32 outstation connections
MGate as DNP3 TCP/UDP outstation: 1 master connection
DNP3 Internal Database:
• For each outstation:
Binary Inputs: 256 points
Analog Inputs: 64 points
Counters: 64 points
Binary Outputs: 256 points
Analog Outputs: 64 points
• When the MGate 5109 is configured as a DNP3 outstation
Binary Inputs: 8192 points
Counters: 2048 points
Binary Outputs: 8192 points
Analog Outputs: 2048 points
Binary Input Events: 1024
Analog Input Events: 1024
Counter Events: 1024
Software
Configuration Options:
Web Console, Serial Console Utility
Configuration:
MXconfig, MXview, SNMP (v1, v2c, v3), Private MIB
Physical Characteristics
Housing:
Metal, IP30
Weight:
507 g (1.12 lb)
Dimensions:
36 x 105 x 140 mm (1.42 x 4.14 x 5.51 in)
Storage Card Slot:
1 microSD (SDHC) card slot supports up to 32 GB
Relay Alarm Circuit:
3-pin circuit with current carrying capacity of 2 A @ 30 VDC
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Storage Temperature:
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity:
5 to 95% (non-condensing)
Vibration: IEC 60068-2-6, IEC 60068-2-64
Shock:
IEC 60068-2-27
Drop:
IEC 60068-2-32
Power Requirements
Input Voltage:
12 to 48 VDC
Input Current:
455 mA max., Class 2
Power Connector:
Terminal block

MGate 5109 Hardware
2-7
Standards and Certifications
Safety:
UL 508, EN 60950-1
Hazardous Location:
Class 1 Division 2, ATEX, IECEx
EMC:
EN 55022/24
EMI:
CISPR 22, FCC Part 15B Class B
EMS:
IEC 61000
-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000
-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000
-4-4 EFT: Power: 4 kV; Signal: 2 kV
IEC 61000
-4-5 Surge: Power: 2 kV; Signal: 2 kV
IEC 61000
-4-6 CS: 150 kHz to 80 MHz: 10 V/m
IEC 61000
-4-8 PFMF
MTBF (mean time between failures)
Time:
859,422 hrs
Standard:
Telcordia SR332
Warranty
Warranty Period:
5 years
Details:
See www.moxa.com/warranty
Reset Button
Restore the MGate to factory default settings by using a pointed object (such as a straightened paper clip) to
hold the reset button down until the Ready LED stops blinking (approx. five seconds).
Pull-high, Pull-low, and Terminator for RS-485
Remove the MGate 5109’s top cover, and you will find DIP switches to adjust each serial port’s pull-high resistor,
pull-low resistor, and terminator.
SW 1 2 3
Pull-high resistor Pull-low resistor Terminator
ON 1 kΩ 1 kΩ 120 Ω
OFF 150 kΩ* 150 kΩ* –*
*Default

MGate 5109 Hardware
2-8
MicroSD
The MGate 5109 provides users with an easy way to backup, copy, replace, or deploy. The MGate is equipped
with a microSD card slot. Users can plug in a microSD card to backup data, including the system configuration
setting, and system data log.
First time using the MGate gateway with a new microSD card
1. Format the microSD card as FAT file system through a PC.
2. Power off the MGate and insert the microSD card (ensure that the microSD card is empty).
3. Power on the MGate. The default settings will be copied to the microSD card.
4. Manually configure the MGate via web console, and all the stored changes will copy to the microSD card for
synchronization.
First time using the MGate with a microSD card containing a configuration file
1. Power off the MGate and insert the microSD card.
2. Power on the MGate.
3. The configuration file stored in the microSD card will automatically copy to the MGate.
Duplicating current configurations to another MGate gateway
1. Power off the MGate and insert a new microSD card.
2. Power on the MGate.
3. The configuration will be copied from the MGate to the microSD card.
4. Power off the MGate and insert the microSD card to the other MGate.
5. Power on the second MGate.
6. The configuration file stored in the microSD card will automatically copy to the MGate.
Malfunctioning MGate replacement
1. Replace the malfunctioning MGate with a new MGate.
2. Insert the microSD card into the new MGate.
3. Power on the MGate.
4. The configuration file stored on the microSD card will automatically copy to the MGate.
MicroSD card writing failure
The following circumstances may cause the microSD card to experience a writing failure:
1. The microSD card has less than 20 Mbytes of free space remaining.
2. The microSD card is write-protected.
3. The file system is corrupted.
4. The microSD card is damaged.
The MGate will stop working in case of the above events, accompanied by a flashing Ready LED and beeping
alarm. When you replace the MGate gateway’s microSD card, the microSD card will synchronize the
configurations stored on the MGate gateway. Note that the replacement microSD card should not contain any
configuration files on it; otherwise, the out-of-date configuration will copy to the MGate device.

3
3. Getting Started
The following topics are covered in this chapter:

Connecting the Power

Connecting Serial Devices

Connecting to a Network

Installing DSU Software

Logging in to the Web Console

Quick Setup
Quick Setup—System Setting
Quick Setup—Select Protocol

MGate 5109 Getting Started
3-2
Connecting the Power
The unit can be powered by connecting a power source to the terminal block:
1. Loosen or remove the screws on the terminal block.
2. Turn off the power source and then connect a 12–48 VDC power line to the terminal block.
3. Tighten the connections, using the screws on the terminal block.
4. Turn on the power source.
Note that the unit does not have an on/off switch. It automatically turns on when it receives power. The PWR
LED on the top panel will glow to indicate that the unit is receiving power. For power terminal block pin
assignments, refer to the Power Input and Relay Output Pinout section in chapter 2.
Connecting Serial Devices
MGate 5109 support Modbus serial and DNP3 serial devices. Before connecting or removing the serial
connection, first make sure the power is turned off. For the serial port pin assignments, see the Pin
Assignments section in chapter 2.
Connecting to a Network
Connect one end of the Ethernet cable to the MGate’s 10/100M Ethernet port and the other end of the cable to
the Ethernet network. The MGate will indicate a valid connection to the Ethernet in the following ways:
•The Ethernet LED maintains a solid green color when connected to a 100 Mbps Ethernet network.
•The Ethernet LED maintains a solid orange color when connected to a 10 Mbps Ethernet network.
•The Ethernet LED will flash when Ethernet packets are being transmitted or received.
Installing DSU Software
If you do not know the MGate gateway’s IP address when setting it up for the first time (default IP is
192.168.127.254); use an Ethernet cable to connect the host PC and MGate gateway directly. If you connect
the gateway and host PC through the same Ethernet switch, make sure there is no router between them. You
can then use Device Search Utility to detect the MGate gateways on your network.
The following instructions explain how to install the Device Search Utility (DSU), a utility to search for MGate
5109 units on a network.
1. Insert the Document and Software CD into the CD-ROM drive. Locate and run the following setup program
to begin the installation process:
dsu_setup_[Version]_Build_[DateTime].exe
The latest version might be named dsu_setup_Ver2.0_Build_xxxxxxxx.exe, for example:
2. You will be greeted by the Welcome window. Click Next to continue.
3. When the Select Destination Location window appears, click Next to continue. You may change the
destination directory by first clicking on Browse....
4. When the Select Additional Tasks window appears, click Next to continue. You may select Create a
desktop icon if you would like a shortcut to the DSU on your desktop.
5. Click Install to start copying the software files.
6. A progress bar will appear. The procedure should take only a few seconds to complete.
7. A message will indicate that the DSU is successfully installed. You may choose to run it immediately by
selecting Launch DSU.
8. You may also open the DSU through Start

Programs

MOXA

DSU.

MGate 5109 Getting Started
3-3
The DSU window should appear as shown below.
Click Search and a new Search window will pop up.
Logging in to the Web Console
Use the Web console to configure the MGate through Ethernet or verify the MGate’s status. Use a web browser,
such as Microsoft Internet Explorer or Google Chrome to connect to the MGate, using the HTTP/HTTPS protocol.
When the MGate gateway appears on the DSU device list, select the gateway and use the right-click the mouse
button to open a web console to configure the gateway.
On the first page of the web console, enter the admin for the default Account name and moxa for the default
Password.

MGate 5109 Getting Started
3-4
Quick Setup
The MGate series now provides a Quick Setup wizard, an illustrated guide specifically designed to make the
configuration process easy. The Quick Setup wizard takes you through the configuration process from start to
finish so that you do not miss any step. The following agent modes are supported in the Quick Setup:
Device 1 Device 2
MB RTU/ASCII Master DNP3 TCP Outstation
MB TCP Client DNP3 serial Outstation
MB TCP Client DNP3 TCP/UDP Outstation
DNP3 serial Master MB TCP server
DNP3 TCP/UDP Master MB RTU/ASCII slave
DNP3 TCP/UDP Master MB TCP slave
Except for above agent modes, other combinations can be configured in Protocol Settings > Protocol
Conversion. For more information, refer to chapter 4.
Quick Setup—System Setting
First, configure the Server Settings to identify the units and Network Settings of the MGate.

MGate 5109 Getting Started
3-5
Quick Setup—Select Protocol
Then, you should select your devices' protocols on each side. After selection, MGate will change its role to the
correct one. For example, if the device is set as a DNP3 TCP/UDP Master, MGate will then automatically
configure as a DNP3 TCP/UDP Outstation by itself. Regarding protocol configuration, refer to chapter 4.
Quick Setup—Role 1 and Role 2 of MGate 5109 (Example 1)
After finishing the device protocol selection, Role 1 and Role 2 of MGate will be confirmed. You will need to
configure the roles on each side by the following steps. Here is an example of Role 1 as a Modbus TCP Server,
and Role 2 as a DNP3 Serial Master.
Modbus TCP settings: Set MGate Unit ID and TCP port.

MGate 5109 Getting Started
3-6
DNP3 serial settings: Set MGate DNP3 Master ID address.
DNP3 serial settings: Add DNP3 Outstation List. For configuration details, refer to chapter 4.
Quick Setup—Finish (Example 1)
Once all the configurations are done, you can check if the parameters are correct on this webpage. Click Save
to make the parameters effective. To view DNP3 mapping data go to the Protocol Settings > I/O Data
Mapping page. For additional details, refer to chapter 4, Protocol Settings—I/O Data Mapping.

MGate 5109 Getting Started
3-7
Quick Setup—Role 1 and Role 2 of MGate 5109 (Example 2)
Here is an example of Role 1 as a DNP3 TCP/UDP Outstation, and Role 2 as a Modbus RTU/ASCII Master.
DNP3 TCP settings: For configuration details, refer to chapter 4.
Modbus RTU/ASCII settings: For configuration details, refer to chapter 4.