Moxa Technologies MGate 5134 Series User manual

P/N: 1802051340010
*1802051340010*
MGate 5134 Series
Quick Installation Guide
Version 1.0, September 2022
Technical Support Contact Information
www.moxa.com/support

2022 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5134 is an industrial Ethernet gateway for Modbus
RTU/ASCII/TCP and PROFINET network communications.
Package Checklist
Before installing the MGate 5134, verify that the package contains the
following items:
•1 MGate 5134 gateway
•Quick installation guide (printed)
•Warranty card
NOTE
Please notify your sales representative if any of the above
items is missing or damaged.
Optional Accessories (can be purchased separately)
•Mini DB9F-to-TB: DB9 female to terminal block connector
•WK-25: Wall-mounting kit, 2 plates, 4 screws, 25 x 43 x 2 mm
Hardware Introduction
LED Indicators
LED
Color
Description
PWR 1, PWR 2
Green
Power is on.
Off
Power is off.
Ready
Off
Power is off.
Green
Steady: Power is on, and the MGate is
functioning normally.
Blinking (1 sec.): The MGate has been
located by the Moxa utility DSU Location
function.
Red
Steady: Power is on, and the MGate is
booting up.
Blinking slowly (0.5 sec.): Indicates an IP
conflict, or the DHCP server is not
responding properly.
Flashing quickly Blinking (0.1 sec.): the
microSD card failed.
PROFINET I/O
Device
Off
No connection with PROFINET I/O controller.
Green
Steady: PROFINET I/O is exchanging data,
and Controller is in RUN mode.
Blinking (1 sec.): PROFINET DCP flash LED.
Red
Steady: Incorrect slot configuration.
Blinking (1sec.): One or more connections
timed out or in STOP mode.
Modbus
RTU/ASCII/TCP
Client
Off
No communication with the Modbus device.
Green
Steady: Normal communication in progress.
Red
Blinking (1 sec.): Communication error.
1. The Modbus slave device returned an
error (exception).
2. Received a frame error (parity error,
checksum error).

- 3 -
LED
Color
Description
3. Timeout (the slave device does not
respond).
4. TCP connection failed (only for Modbus
TCP).
ETH 1, ETH 2
Green
Steady ON: Ethernet link on at 100Mbps.
Blinking: Data transmitting at 100Mbps.
Amber
Steady ON: Ethernet link on at 10Mbps.
Blinking: Data transmitting at 10Mbps.
Off
Link is down or not connected.
Dimensions
Reset Button
Restore the MGate to factory default settings by using a pointed object
(such as a straightened paper clip) to hold the reset button down until
the Ready LED stops blinking (approximately five seconds).
Hardware Installation Procedure
1. Connect the power adapter. Connect the 12-48 VDC power line or
DIN-rail power supply to the MGate 5134’s terminal block.
2. Use a serial cable to connect the MGate to the Modbus device.
3. Use an Ethernet cable to connect the MGate to the PROFINET I/O
controller.
4. The MGate 5134 is designed to be attached to a DIN rail or
mounted on a wall. For DIN-rail mounting, push down the spring
and properly attach it to the DIN rail until it “snaps” into place. For
wall mounting, install the wall-mounting kit (optional) first and then
screw the device onto the wall.

- 4 -
The following figure illustrates the two mounting options:
Wall- or Cabinet-mounting
We provide two metal plates to mount the unit on
a wall or inside a cabinet. Attach the plates to the
unit’s rear panel with screws. With the plates
attached, use screws to mount the unit on the
wall. The heads of the screws should be 5 to 7 mm
in diameter, the shafts should be 3 to 4 mm in
diameter, and the length of the screws should be
over 10.5 mm.
Software Installation Information
Please download the User Manual and Device Search Utility (DSU) from
Moxa’s website: www.moxa.com
For using the DSU, refer to the User’s Manual. The MGate 5134 also
supports login via a web browser.
Default IP address: 192.168.127.254
Create your administration account and password when you log in the
first time.
Pin Assignments
Modbus Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5*
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
*Signal ground

- 5 -
Ethernet Port (RJ45)
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Power Input and Relay Output Pinouts
V2+ V2-
V1+ V1-
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Parameters
Power Input
12 to 48 VDC
Power Consumption
455 mA max.
Relays
Contact Current Rating
Resistive load: 2 A @ 30 VDC
Environmental Limits
Operating Temperature
Standard models: -10 to 60°C (14 to
140°F)
Wide temp. models: -40 to 75°C (-40 to
167°F)
Storage Temperature
(package included)
-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity
5 to 95% RH
Physical Characteristics
Dimensions
25 x 90 x 129.6 mm (0.98 x 3.54 x 5.1 in)
Weight
294 g (0.65 lb)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
1,240,821 hrs.
ATTENTION
Power
terminal plug wiring size is 28-14 AWG, tighten to 1.7
in-lbs, wire min. 80°C. Use copper conductors only.
Hot
surface label.
Functional earth terminal.

- 6 -
ATTENTION
•
This device is an open-type equipment and intended to be
installed in a suitable enclosure.
•
If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment
may be impaired.
•
When installing the device, the
assembler is responsible for
the securing the safety of the system in which the
equipment is incorporated.
NOTE
•This device is intended for use indoors and at altitudes up
to 2,000 meters.
•Pollution degree 2.
NOTE
Clean the device with a soft cloth, dry or with water.
NOTE
The power input specification complies with the requirements of
SELV (Safety Extra Low Voltage), and the power supply should
comply with UL 61010-1 and UL 61010-2-201.
For any repair or maintenance needs, please contact us.
Moxa Inc.
No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan
[phone]