Moxa Technologies NPort 6150 Series User manual

— 1 — — 2 — — 3 —
NPort 6150 Series
Quick Installation Guide
Third Edition, June 2008
1. Overview
The NPort 6150 series of secure serial device servers provide reliable
serial-to-Ethernet connectivity for a wide range of serial devices. The
NPort 6150 supports TCP Server, TCP Client, UDP, and Pair-Connection
operation modes to ensure the compatibility of network software. In
addition, the NPort 6150 also supports Secure TCP Server, Secure TCP
Client, Secure Pair-Connection, and Secure Real COM modes for security
critical applications such as banking, telecom, access control and remote
site management.
2. Package Checklist
Before Installing the NPort 6150 secure device server, verify that the
package contains the following items:
y1 NPort 6150
yDocument & Software CD
yQuick Installation Guide (this guide)
yPower Adaptor
yProduct Warranty Statement
y2 Wall mount ears
Optional Accessories
yDK-35A: DIN-Rail mounting kit (35 mm)
yDIN-Rail Power Supply
yCBL-RJ45M9-150: 8-pin RJ45 to male DB9 cable
yCBL-RJ45M25-150: 8-pin RJ45 to male DB25 cable
NOTE: Please notify your sales representative if any of the above items
are missing or damaged.
3. Hardware Introduction
LAN RESET POWER JACK
LED Inicators
P1
Reset Button—Press the Reset button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button.
LED Indicators
LED Name LED Color LED Function
PWR Red Power is being supplied to the power input.
Steady on: Power is on and the NPort
6150 is booting up.
Red
Blinking: Indicates an IP conflict, or, the
DHCP or BOOTP server did
not respond properly or a relay
output occurred. Check the
relay output first. If after
resolving the relay output the
RDY LED is still blinking,
then there is an IP conflict, or
the DHCP or BOOTP server
did not respond properly.
Steady on: Power is on and the NPort
6150 is functioning normally.
Green Blinking: The device server has been
located by the Administrator’s
Location function.
Ready
Off Power is off, or power error condition exists.
Orange 10 Mbps Ethernet connection.
Green 100 Mbps Ethernet connection
Link
Off Ethernet cable is disconnected, or has a
short.
Orange Serial port is receiving data.
Green Serial port is transmitting data.
P1
Off No data is being transmitted or received
through the serial port.
Green Serial port was opened by server side
software.
P1 in-use
LED Off Serial port has not been opened by server
side software.
Adjustable pull high/low resistor for RS-422/485 (150 KΩor 1 KΩ)
JP4, JP5
Jumpers are used to set the pull
high/low resistors. The default is
150 KΩ. Short the jumpers to set
this value to 1 KΩ. Do not use the
KΩsetting with RS-232 mode,
since doing so will degrade the
RS-232 signals and shorten the
communication distance.
P/N: 1802061500012

— 4 — — 5 — — 6 —
4. Hardware Installation Procedure
STEP 1: Connect the 12-48 VDC power adaptor to the NPort 6150 and
then plug the power adaptor into a DC outlet.
STEP 2: For first-time configuration, use a cross-over Ethernet cable to
connect the NPort 6150 directly to your computer’s Ethernet
cable. For connecting to a network, use a standard
straight-through Ethernet cable to connect to a hub or switch.
STEP 3: Connect the NPort 6150’s serial port to a serial device.
Placement Options
The NPort 6150 can be placed flat on a desktop or other horizontal
surface. In addition, you may use the DIN-Rail or Wall Mount options, as
illustrated below.
Wall Mount Din Rail
NPort6150
5. Software Installation Information
The Document & Software CD contains the User’s Manual, NPort Search
Utility, and the PComm Lite Suite. Insert the CD and follow the
on-screen instructions. Please refer to the User’s Manual for additional
details on using the NPort Search Utility and PComm Lite.
6. PinAssignments and Cable Wiring
RS-232/422/485 PinAssignment (male DB9)
Pin RS-232 RS-422
4-wire RS-485 2-wire RS-485
1 DCD TxD-(A) ---
2 RXD TxD+(B) ---
3 TXD RxD+(B) Data+(B)
4 DTR RxD-(A) Data-(A)
5 GND GND GND
6 DSR --- ---
7 RTS --- ---
8 CTS --- ---
9 --- --- ---
12345
6789
Two serial cables for connecting the NPort 6150 to a serial device can be
purchased separately. The wiring diagrams for the two cables are shown
below.
CBL-RJ45M9-150: 8-pin RJ45 to male DB9
NPort 6150
9 pins 9 pins
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RS-232
Device
DCD
TxD
RxD
DSR
GND
DTR
CTS
RTS
Cable Wiring
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Female DB9 Male DB9Male DB9 Female DB9
CBL-RJ45M25-150: 8-pin RJ45 to Male DB25
NPort 6150
9 pins 25 pins
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
RS-232
Device
DCD
TxD
RxD
DSR
GND
DTR
CTS
RTS
Cable Wiring
1
2
3
4
5
6
7
8
8
3
2
20
7
6
4
5
Female DB9 Male DB25Male DB9 Female DB25
7. Specifications
LAN
Ethernet: 10/100 Mbps, RJ45
Protection: Built-in 1.5 KV magnetic isolation
Serial
No. of ports: 1
Interface: RS-232/422/485 (male DB9)
Serial Communication Parameters
Parity: None, Even, Odd, Space, Mark
Data bits: 5, 6, 7, 8
Stop bit(s): 1, 1.5, 2
Flow control: RTS/CTS, XON/XOFF, DTR/DSR
Speed: 50 bps to 921.6 Kbps
Console Port: RS-232 (please see the User’s Manual for
detailed operating instructions)
Software Features
Protocols: I C M P, I P, T C P, U D P, D H C P, B O O T P, Te l n e t ,
DNS, SNMP, HTTP, SMTP, HTTPS, SSL, SSH,
PPPoE, RFC2217
Utilities: NPort Search Utility for Windows
98/ME/NT/2000/XP/2003/Vista/XP x64/2003
x64/Vista x64
Security Protocols: DES/3DES/AES
OS Driver Support: Real COM drivers:
Windows 95/98/ME/NT/2000/XP/XP
x64/2003/2003 x64/Vista/Vista x64
Real TTY drivers: Linux 2.4 and 2.6
Fixed TTY drivers: SCO Unix, SCO OpenServer
5, OpenServer 6, UnixWare 7, UnixWare 2.1,
SVR4.2, QNX 4.25, QNX 6, Solaris 10,
FreeBSD 5, FreeBSD 6
Configuration: Web Console, Serial/Telnet Console, Windows
utility
Power Requirements
Power input: 12 to 48 VDC
Mechanical Specifications
Material: Aluminum (1 mm)
Environment
Operating Temperature: 0-55°C (32 to 131°F), 5 to 95% RH
Storage Temperature: -20 to 85°C (-4 to 185°F), 5 to 95%RH
Regulatory Approvals
EMC: FCC Class A, CE Class A
Safety: UL, CUL, TUV
Click here for online support:
www.moxa.com/support
The Americas: [phone] (toll-free: 1-888-669-2872)
Europe: [phone]
Asia-Pacific: [phone]
China: [phone] (toll-free: 800-820-5036)
©2008 Moxa Inc., all rights reserved.
Reproduction without permission is prohibited.