Moxa Technologies EDS-510E Series User manual

Moxa Managed Ethernet Switch
(UI_2.0_FW_5.x) User Manual
Version 2.2, June 2022
www.moxa.com/products
© 2022 Moxa Inc. All rights reserved.
Models covered by this user manual (only applies to products
using firmware version 5.0 or higher):
EDS-510E, EDS-518E, EDS-528E, EDS-G508E, EDS-G512E, EDS-
G516E, EDS-P506E-4PoE, EDS-G512E-8PoE, IKS-6726A, IKS-6728A,
IKS-6728A-8PoE, IKS-G6524A, ICS-G7526A, ICS-G7528A, ICS-
G7748A, ICS-G7750A, ICS-G7752A, IKS-G6824A, ICS-G7826A, ICS-
G7828A, ICS-G7848A, ICS-G7850A, ICS-G7852A, PT-G7728, PT-G7828

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
The sof tware described in this manual is furnished under a license agreement and may be used only in accordance
with the terms of that agreement.
Copyright Notice
© 2022 Moxa Inc. All rights reserved.
Trademarks
The MOXA logo is a registered trademark of Moxa Inc.
All other trademarks or registered marks in this manual belong to their respective manuf acturers.
Disclaimer
•Information in this document is subject to change without notice and does not represent a commitment
on the part of Moxa.
•Moxa provides this document as is, without warranty of any kind, either expressed or implied, including,
but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or
changes to this manual, or to the products and/or the programs described in this manual, at any time.
•Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no
responsibility f or its use, or f or any inf ringements on the rights of third parties that may result f rom its
use.
•This product might include unintentional technical or typographical errors. Changes are periodically
made to the information herein to correct such errors, and these changes are incorporated into new
editions of the publication.
Technical Support Contact Information
www.moxa.com/support

Table of Contents
1. About This Ma nua l .......................................................................................................................... 5
2. Getting Started ............................................................................................................................... 6
USB Console Configuration (115200, None, 8, 1, VT100) ........................................................................ 6
Conf igurat ion by Comman d Line Interf ace (CLI) .................................................................................... 9
Conf igurat ion by Web Co nsole ...........................................................................................................11
Disabling Telnet and Browser Access ..................................................................................................12
3. Featured Functions ....................................................................................................................... 13
Home ............................................................................................................................................13
System Settings .............................................................................................................................14
System Information .................................................................................................................14
User Account...........................................................................................................................15
Password Login Policy ...............................................................................................................17
Network .................................................................................................................................18
Date and Time.........................................................................................................................20
IEEE 1588 PTP.........................................................................................................................23
Warning Notif icat ion .................................................................................................................26
MAC Address Table...................................................................................................................32
System Files ...........................................................................................................................33
Turbo Ring DIP Switch ..............................................................................................................36
Restart...................................................................................................................................37
Factory Def ault........................................................................................................................38
PoE (PoE Mode ls On ly) .....................................................................................................................38
PoE Settings ...........................................................................................................................39
VLAN ............................................................................................................................................49
The Virtual LAN (VLAN) Concept .................................................................................................49
Sample Applications of VLANs Using Moxa Switches .......................................................................51
Conf iguring a Virt ual LAN ..........................................................................................................52
VLAN Name Setting ..................................................................................................................54
QinQ Settings..........................................................................................................................55
VLAN Table .............................................................................................................................55
Port ..............................................................................................................................................56
Port Settings ...........................................................................................................................56
Port Status .............................................................................................................................57
Link Aggregation......................................................................................................................57
Link-Swap Fast Recovery ..........................................................................................................59
Multicast........................................................................................................................................60
The Concept of Multicast Filtering ...............................................................................................60
IGMP Snooping ........................................................................................................................63
IGMP Snooping Setting .............................................................................................................63
IGMP Group Status...................................................................................................................64
Stream Table ..........................................................................................................................65
Static Multicast Address ............................................................................................................66
GMRP ....................................................................................................................................66
Multicast Filter ing Be havior ........................................................................................................67
QoS ..............................................................................................................................................68
The Traff ic Prioritizati on Co ncept ................................................................................................68
Conf iguring Traff ic Prioritization ..................................................................................................70
CoS Class if ication.....................................................................................................................70
Priority Mapp ing (Type 1) ..........................................................................................................71
Priority Mapping (Type 2) ..........................................................................................................72
DSCP Mapp ing .........................................................................................................................72
Rate Lim it ing ...........................................................................................................................73
Security ........................................................................................................................................79
Management Interface..............................................................................................................79
Trusted Access ........................................................................................................................81
SSL Certificate Management ......................................................................................................82
SSH Key Management ..............................................................................................................82
Authentication .........................................................................................................................83

Port Security ...........................................................................................................................88
Port Access Control Table ..........................................................................................................91
Broadcast Storm Protection .......................................................................................................91
Loop Protection .......................................................................................................................92
Access Control List ...................................................................................................................92
DHCP ............................................................................................................................................99
IP-Port Binding ........................................................................................................................99
DHCP Relay Age nt ....................................................................................................................99
SNMP.......................................................................................................................................... 102
SNMP Read/Write Settings....................................................................................................... 103
Trap Settings ........................................................................................................................ 104
Ind ustria l Protoco ls........................................................................................................................ 108
Diag nostics .................................................................................................................................. 108
LLDP.................................................................................................................................... 108
Ping ..................................................................................................................................... 109
Port Mirroring ........................................................................................................................ 110
Monitoring ................................................................................................................................... 111
CPU/Memory Utilization........................................................................................................... 111
Statistics .............................................................................................................................. 112
Fiber Dig ita l Dia gnost ics Monitor ing (SFP DDM a nd F iber Check) ..................................................... 114
Event Log ............................................................................................................................. 116
Tracking ...................................................................................................................................... 117
Interf ace Tracking.................................................................................................................. 117
Ping Track ing ........................................................................................................................ 119
Logic Tracking ....................................................................................................................... 120
Tracking Tab le ....................................................................................................................... 121
A. MIB Groups..................................................................................................................................122

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
5
1. About This Manual
Thank you f or purchasing a Moxa managed Ethernet switch. Read this user’s manual to learn how to
connect your Moxa switch to Ethernet-enabled devices used f or industrial applications.
A synopsis of chapters 2 and 3 are given below:
•Chapter 2: Getting Started
In this chapter, we explain the initial installation process f or a Moxa switch. Moxa switches provide three
interfaces to access the configuration settings: USB console interface, command line interface, and web
console interface.
•Chapter 3: Featured Functions
In this chapter, we explain how to access a Moxa switch’s various conf iguration, monitoring, and
management f unctions. The f unctions can be accessed by USB console, Telnet console, and web console
(web browser). We describe how to configure the switch functions via web console, which provides the
most user-f riendly way to conf igure a Moxa switch.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
6
2. Getting Started
In this chapter, we explain how to install a Moxa switch for the first time. There are three ways to access
the Moxa switch’s configuration settings: USB console, command line interface, or web-based interface. If
you do not know the Moxa switch’s IP address, you can open the USB console by connecting the Moxa
switch to a PC’s USB port with a USB cable. You can open the Telnet or web-based console over an Ethernet
LAN or over the Internet.
USB Console Configuration (115200, None, 8,
1, VT100)
NOTE
A Moxa switch allows multi-session connections (up to 6) by connecting to the web console and another
console (serial or Telnet) at the same time.
NOTE
We recommend using PComm Terminal Emulator when opening the USB console. This sof tware can be
downloaded free of charge from the Moxa website.
Bef ore running PComm Terminal Emulator, f irst install the USB console driver on your PC and then connect
the Moxa switch’s USB console port to your PC’s USB port with a USB cable.
Af ter installing PComm Terminal Emulator, open the Moxa switch’s USB console as f ollows:
1. From the Windows desktop, click Start > Moxa > PComm Lite Ver1.6 > Terminal Emulator.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
7
2. Select Open under the Port Manager menu to open a new connection.
3. The Property window should open. On the Communication Parameter tab for Ports, select the COM
port that is being used f or the console connection. Set the other f ields as f ollows: 115200 for Baud
Rate, 8f or Data Bits, None for Parity, and 1for Stop Bits.
4. On the Terminal tab, select VT100 for Terminal Type, and then click OK to continue.
5. In the terminal window, the Moxa switch will prompt you to select a terminal type. Enter 1to select
ansi/vt100 and then press Enter.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
8
6. The USB console will prompt you to log in. Press Enter and select admin or user. Use the down arrow
key on your keyboard to select the Password f ield and enter a password if desired. This password will
be required to access any of the consoles (web, serial, Telnet).
NOTE
By def ault, the password assigned to the Moxa switch is moxa. Be sure to change the def ault password
af ter you f irst log in to help keep your system secure.
7. The Main Menu of the Moxa switch’s USB console should appear. (In PComm Terminal Emulator, you
can adjust the f ont by selecting Font… f rom the Edit menu.)
8. Use the f ollowing keys on your keyboard to navigate the Moxa switch’s USB console:
Key
Function
Up, down, right, left arrow keys, Tab
Move the onscreen cursor
Enter
Display and select options
Space
Toggle options
Esc
Previous menu

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
9
Configuration by Command Line Interface
(CLI)
Opening the Moxa switch’s Telnet or web console over a network requires that the PC host and Moxa switch
are on the same logical subnet. You may need to adjust your PC host’s IP address and subnet mask. By
def ault, the Moxa switch’s IP address is 192.168.127.253 and the Moxa switch’s subnet mask is
255.255.255.0 (ref erred to as a Class B network). Your PC’s IP address must be set to 192.168.xxx.xxx if
the subnet mask is 255.255.0.0, or to 192.168.127.xxx if the subnet mask is 255.255.255.0.
NOTE
To connect to the Moxa switch’s Telnet or web console, your PC host and the Moxa switch must be on the
same logical subnet.
NOTE
When connecting to the Moxa switch’s Telnet or web console, f irst connect one of the Moxa switch’s
Ethernet ports to your Ethernet LAN, or directly to your PC’s Ethernet port. You may use either a straight-
through or cross-over Ethernet cable.
NOTE
The Moxa switch’s def ault IP address is 192.168.127.253.
Af ter making sure that the Moxa switch is connected to the same LAN and logical subnet as your PC, open
the Moxa switch’s Telnet console as follows:
1. Click Start > Run f rom the Windows Start menu and then Telnet to the Moxa switch’s IP address f rom
the Windows Run window. You may also issue the Telnet command f rom a DOS prompt.
2. In the terminal window, the Telnet console will prompt you to select a terminal type. Type 1to choose
ansi/vt100, and then press Enter.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
10
3. The Telnet console will prompt you to log in. Press Enter and then select admin or user. Use the down
arrow key on your keyboard to select the Password f ield and enter a password if desired. This
password will be required to access any of the consoles (web, serial, Telnet). If you do not wish to
create a password, leave the Password f ield blank and press Enter.
4. The Main Menu of the Moxa switch’s Telnet console should appear.
5. In the terminal window, select Preferences… f rom the Terminal menu on the menu bar.
6. The Terminal Preferences window should appear. Make sure that VT100 Arrows is checked.
7. Use the f ollowing keys on your keyboard to navigate the Moxa switch’s Telnet console:
Key
Function
Up, down, right, left arrow keys, Tab
Move the onscreen cursor
Enter
Display and select options
Space
Toggle options
Esc
Previous menu
NOTE
The Telnet console looks and operates in precisely the same manner as the USB console.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
11
Configuration by Web Console
The Moxa switch’s web console is a convenient platf orm f or modif ying the conf iguration and accessing the
built-in monitoring and network management f unctions. You can open the Moxa switch’s web console using
a standard web browser, such as Internet Explorer.
NOTE
When connecting to the Moxa switch’s Telnet or web console, your PC host and the Moxa switch must be
on the same logical subnet.
NOTE
If the Moxa switch is conf igured f or other VLAN settings, you must make sure your PC host is on the
management VLAN.
NOTE
When connecting to the Moxa switch’s Telnet or web console, f irst connect one of the Moxa switch’s
Ethernet ports to your Ethernet LAN, or directly to your PC’s Ethernet port. You may use either a straight-
through or cross-over Ethernet cable.
NOTE
The Moxa switch’s def ault IP address is 192.168.127.253.
Af ter making sure that the Moxa switch is connected to the same LAN and logical subnet as your PC, open
the Moxa switch’s web console as follows:
1. Connect your web browser to the Moxa switch’s IP address by entering it in the Address or URL f ield.
2. The Moxa switch’s web console will open, and you will be prompted to log in. Select the login account
(admin or user) and enter the Password. This password will be required to access any of the consoles
(web, serial, Telnet). If you do not wish to create a password, leave the Password f ield blank and
press Enter.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
12
NOTE
By def ault, the password assigned to the Moxa switch is moxa. Be sure to change the def ault password
af ter you f irst log in to help keep your system secure.
3. After logging in, you may need to wait a few moments for the web console to appear. Use the folders in
the lef t navigation panel to navigate between dif f erent pages of conf iguration options.
Disabling Telnet and Browser Access
If you are connecting the Moxa switch to a public network but do not intend to manage it over the network,
we suggest disabling both the Telnet and web consoles. This is done f rom the USB console by navigating to
System Identif ication under Basic Settings > System Information. Disable or enable the Telnet
Console and Web Configuration as shown below:

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
13
3. Featured Functions
In this chapter, we explain how to access the Moxa switch’s various conf iguration, monitoring, and
management functions. These functions can be accessed by USB console, Telnet console, or web console.
The USB console can be used if you do not know the Moxa switch’s IP address. To access the USB console,
connect switch’s USB port to your PC’s COM port. The Telnet and web consoles can be opened over an
Ethernet LAN or the Internet.
The web console is the most user-f riendly interf ace f or conf iguring a Moxa switch. In this chapter, we use
the web console interface to introduce the console functions. There are only a few differences between the
web console, USB console, and Telnet console.
Home
The Home page shows the summary of the Moxa switch inf ormation including System Inf ormation,
Redundancy Protocol, Event Log, and Device virtualization panel. By showing the switch's inf ormation and
event log, the operators can easily understand the system and port link status at a glance.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
14
System Settings
The System Settings section includes the most common settings required by administrators to maintain
and control a Moxa switch.
System Information
Def ine System Information items to make it easier to identify diff erent switches that are connected to
your network.
Switch Name
Setting
Description
Factory Default
Max. 30 characters
This option is usef ul f or dif f erentiating between the roles or
applications of dif f erent units. Example: factorySwitch1 none
NOTE
The Switch Name f ield f ollows the PROFINET I/O naming rule. The name can only include any of these
characters, a-z/A-Z/0-9/-/., and the name cannot start with port-xyz or port-xyz-abcde where
xyzabcde=0...9 or is in the form n.n.n.n where n=0...9
Switch Location
Setting
Description
Factory Default
Max. 255 characters This option is usef ul f or dif f erentiating between the locations
of different switches. Example: production line 1.
Switch Location
Switch Description
Setting
Description
Factory Default
Max. 30 characters
This option is usef ul f or recording a more detailed description
of the unit. Switch Model name

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
15
Contact Information
Setting
Description
Factory Default
Max. 30 characters
This option is usef ul f or providing inf ormation about who is
responsible f or maintaining this unit and how to contact this
person.
None
Web Login Message
Setting
Description
Factory Default
Max. 240 characters
This option is usef ul as it shows a message when a user’s
login is successful
Switch Location
Login Authentication Failure Message
Setting Description Factory Default
Max. 240 characters
This option is usef ul as it shows a message when a user’s
login has f ailed Switch Location
User Account
The Moxa switch supports the management of accounts, including establishing, activating, modif ying,
disabling, and removing accounts. There are two levels of configuration access: admin and user. Accounts
with admin authority have read/write access of all conf iguration parameters, whereas accounts with user
authority only have read access to view conf iguration items.
NOTE
1. In order to maintain a higher level of security, we strongly suggest that you change the password af ter
you f irst log in.
2. By def ault, the admin user account cannot be deleted or disabled.
Active
Setting
Description
Factory Default
Checked
This account can access the switch’s configuration settings.
Checked
Unchecked
This account cannot access the switch’s conf iguration settings.
Authority
Setting
Description
Factory Default
admin
This account has read/write access of all configuration
parameters.
admin
user
This account can only view conf iguration parameters.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
16
Creating a New Account
Click Create, type in the user name and password, and assign an authority to the new account. Click Apply
to add the account to the Account List table.
Setting
Description
Factory Default
User Name
(Max. of 30 characters) User Name None
Password
Password for the user account.
(between 4 and 16 characters) None
Modifying an Existing Account
Select an existing account f rom the Account List table, modif y the account details, and then click Apply to
save the changes.
Deleting an Existing Account
Select an account f rom the Account List table and then click Delete to delete the account.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
17
Password Login Policy
In order to prevent hackers from cracking the password, Moxa switches allow users to configure a password
f or their account and lock the account in the event that the wrong password is entered. The account
password policy requires passwords to be of a minimum length and complexity with a strength check. If
Account Login Failure Lockout is enabled, you will need to conf igure the Retry Failure Threshold and
Lockout Time parameters. If the number of login attempts exceeds the Retry Failure Threshold, users will
need to wait the number of minutes conf igured in Lockout Time bef ore trying again.
NOTE
The valid special characters are: (~!@#$%^&*-_|;:,.<>[]{}()).

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
18
Network
Network conf iguration allows users to conf igure both IPv4 and IPv6 parameters f or management access
over the network. The Moxa switch supports both IPv4 and IPv6, and can be managed through either of
these address types.
IP Settings
The IPv4 settings include the switch’s IP address and subnet mask, as well as the IP address of the default
gateway. In addition, input cells are provided f or the IP addresses of a 1st and 2nd DNS server.
The IPv6 settings include two distinct address types—Link-Local Unicast addresses and Global Unicast
addresses. A Link-Local address makes the switch accessible over IPv6 for all devices attached to the same
local subnet. To connect to a larger network with multiple segments, the switch must be conf igured with a
Global Unicast address.
Get IP From
Setting
Description
Factory Default
DHCP
The Moxa switch’s IP address will be assigned automatically by
the network’s DHCP server.
Manual
BOOTP
The Moxa switch’s IP address will be assigned automatically by
the network’s BootP server.
Manual
The Moxa switch’s IP address must be set manually.
IP Address
Setting
Description
Factory Default
IP address f or the Moxa
switch Assigns the Moxa switch’s IP address on a TCP/IP network. 192.168.127.253
Subnet Mask
Setting
Description
Factory Default
Subnet mask f or the
Moxa switch
Identif ies the type of network the Moxa switch is connected to
(e.g., 255.255.0.0 f or a Class B network, or
255.255.255.0 f or
a Class C network).
24(255.255.255.0)
Default Gateway
Setting
Description
Factory Default
IP address f or gateway
Specifies the IP address of the router that connects the LAN to
an outside network. None

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
19
DNS Server IP Addresses
Setting
Description
Factory Default
1st DNS Server
Specifies the IP address of the DNS server used by your
network. After specifying the DNS server’s IP address, you can
use the Moxa switch’s URL (e.g., www.PT.company.com) to
open the web console instead of entering the IP address.
None
2nd DNS Server
Specifies the IP address of the secondary DNS server used by
your network. The Moxa switch will use the secondary DNS
server if the first DNS server fails to connect.
None
IPv6 Global Unicast Address Prefix (Prefix Length: 64 bits) Default Gateway
Setting
Description
Factory Default
Global Unicast Address
Pref ix
The prefix value must be formatted according to the RFC 2373
“IPv6 Addressing Architecture,” using 8 colon-separated 16-bit
hexadecimal values. One double colon may be used in the
address to indicate the appropriate number of zeros required
to f ill the undef ined f ields.
None
IPv6 Global Unicast Address
Setting
Description
Factory Default
None
Displays the IPv6 Global Unicast address. The network portion
of the Global Unicast address can be configured by specifying
the Global Unicast Pref ix and using an EUI-64 interf ace ID in
the low order 64 bits. The host portion of the Global Unicast
address is automatically generated using the modif ied EUI-64
form of the interface identifier (Switch’s MAC address).
None
IPv6 Link-Local Address
Setting
Description
Factory Default
None
The network portion of the Link-Local address is FE80 and the
host portion of the Link-Local address is automatically
generated using the modif ied EUI-64 f orm of the interface
identif ier (Switch’s MAC address).
None
IPv6 Neighbor Cache
The IPv6 neighbor cache includes the neighboring node’s IPv6 address, the corresponding Link-Layer
address, and the current state of the entry.

Moxa Managed Ethernet Switch (UI_2.0_FW_5.x) User Manual
20
Date and Time
The Moxa switch has a time calibration f unction based on inf ormation f rom an NTP server or user specif ied
time and date, allowing f unctions such as automatic warning emails to include a time and date stamp.
NOTE
The user must update the Current Time and Current Date af ter powering of f the switch f or a long period of
time (f or example a f ew days). The user must pay particular attention to this when there is no NTP server,
LAN, or Internet connection.
System Up Time
Indicates how long the Moxa switch has been up and running since the last cold start.
Current Time
Setting
Description
Factory Default
User-specif ied time
Indicates time in yyyy-mm-dd format.
None
Time Zone
Setting Description Factory Default
Time zone
Specifies the time zone, which is used to determine the local
time offset from GMT (Greenwich Mean Time).
GMT (Greenwich
Mean Time)
Daylight Saving Time
The Daylight Saving Time settings are used to automatically set the Moxa switch’s time ahead according to
national standards.
Start Date
Setting
Description
Factory Default
User-specified date
Specif ies the date that Daylight Saving Time begins.
None
End Date
Setting
Description
Factory Default
User-specified date Specif ies the date that Daylight Saving Time ends. None
Offset
Setting
Description
Factory Default
User-specif ied hour
Specifies the number of hours that the time should be set
f orward during Daylight Saving Time. None
Clock Source
Setting
Description
Factory Default
Local Conf igure clock source f rom local time
Local
NTP
Configure clock source f rom NTP
SNTP
Configure clock source f rom SNTP