Moxa Technologies EtherDevice EDS-P506E-4PoE Series User manual

P/N: 1802005060020
*1802005060020*
EDS-P506E-4PoE Series
Quick Installation Guide
Moxa EtherDevice™ Switch
Edition 1.0, February 2018
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2018 Moxa Inc. All rights reserved.

- 2 -
Package Checklist
The EDS-P506E-4PoE is shipped with the following items. If any of these
items are missing or damaged, please contact your customer service
representative for assistance.
•EDS-P506E-4PoE Ethernet switch
•USB cable
•Protective caps for unused ports
•Documentation
•Quick installation guide (printed)
•Warranty card
Features
•Up to 4 10/100BaseT(X) ports and 2 10/100/1000BaseT(X) or
100/1000BaseSFP ports
•Up to 4 IEEE 802.3af, IEEE 802.3at PoE+ standard, and 4-pair PoE
60W ports
36-watt output per PoE+ port in 2 pair PoE high power mode
60-watt output per PoE+ port in 4 pair PoE high power mode
Intelligent PoE power management functions
•Operate with 180 watts full PoE+ loading at -40 to 75°C
•Turbo Ring and Turbo Chain (recovery time < 20 ms @ 250
switches), RSTP/STP, and MSTP for network redundancy
•TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance
network security
•Easy network management by web browser, CLI, USB serial console,
ABC-02-USB, MXview, MXconfig, and Windows utility
Default Settings
•Default IP address: 192.168.127.253
•Default Subnet Mask: 255.255.255.0
•Default Usernames: admin, user
•Default Password: moxa

- 3 -
Panel Views of EDS-P506E-4PoE Series
Front Panel
1.
100BaseT(X) LED indicator
2.
10BaseT(X) LED indicator
3.
10/100 60W PoE+ Ports
Port 1 to 4
4.
System status LED:
•STATE LED indicator
•PWR1 LED indicator
•PWR2 LED indicator
•FAULT LED indicator
•MSTR/HEAD LED indicator
•CPLR/TAIL LED indicator
5.
USB storage port
6.
G1 and G2 port LED indicator
7.
Combo 10/100/1000BaseT(X) or
100/1000BaseSFP slot
8.
Model Name
9.
SmartPoE LED indicator of PoE+ ports
Top Panel
1.
Reset button
2.
USB console port
3.
DIP switches for Turbo Ring, Ring
Master, and Ring Coupler
4.
Grounding screw
5.
4-pin terminal block for digital input
and power input 2
6.
4-pin terminal block for relay output
and power input 1
Rear Panel
1.
Screw holes for wall mounting kit
2.
DIN-rail mounting kit

- 4 -
Mounting Dimensions
Unit = mm (inch)

- 5 -
DIN-Rail Mounting
The metal DIN-rail kit is fixed to the back panel of the EDS-P506E-4PoE
Series when you take it out of the box. Mount the EDS-P506E-4PoE Series
on corrosion-free mounting rails that meet the EN 60715 standard.
Installation
STEP 1—Insert the upper lip
of the DIN r
ail into the DIN-r
ail
mounting kit.
STEP 2
—Press the
EDS
-P506E-4PoE Series
towards the
DIN rail until it
snaps into place.
Removal
STEP 1—Pull down the latch
on the mounting kit
with a
screwdriver.
STEP 2
& 3—Slightly pull
the
EDS
-P506E-4PoE Series
forward and lift up to remove
it from the DIN r
ail.
Wall Mounting (Optional)
For some applications, you will find it convenient to mount the
EDS-P506E-4PoE Series on a wall (in an enclosure or industrial panel), as
shown in the following illustrations:
STEP 1—
Remove the
aluminum DIN rail attachment
plate from the rear panel
of
the
EDS-P506E-4PoE Series,
and then attach the wall
mount plates
with M3 screws
,
as shown
in the figure at the
right.

- 6 -
STEP 2—Mounting the EDS-P506E-4PoE Series on the
wall requires 4 screws. Use the
EDS-P506E-4PoE
S
eries
, with wall mount plates attached, as a guide to
mark the correct locations of the 4 screws. The heads
of the screws should be less than 6.0 mm in diameter,
and the shafts should be less than 3.5
mm in diameter,
as shown in the figure on at right.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shank size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the Wall Mounting Plates.
Do not screw the screws in all the way—leave about 2 mm to allow room
for sliding the wall mount panel between the wall and the screws.
STEP 3—Once the screws are fixed
to
the wall, insert the four screw
heads through the wide parts of the
keyhole
-
shaped apertures, and then
slide
the EDS-P506E-4PoE
downwards, as indicated
in the
figure
at the right. Tighten the four
screws for
more stability.
ATTENTION
The product should
be mounted in an
Industrial Control Panel and
the ambient temperature should not exceed 75°C.
Wiring Requirements
WARNING
Do not disconnect modules or wires unless power has been
switched off or the area is known to be non
-hazardous. The
devices may only be connected to the supply voltage shown on
the type plate. The devices are designed for operation with a
S
afety Extra-Low V
oltage. Thus, they may only be connected to
the supply voltage connections and to the signal contact with the
S
afety Extra-Low Voltages (SELV) in compliance with IEC950/
EN60950/ VDE0805.
ATTENTION
This unit is a built
-in type. When the unit is installed in another
piece of equipment, the equipment enclosing the unit must
comply w
ith fire enclosure regulation IEC 60950/EN60950 (or
similar regulation).

- 7 -
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa EtherDevice Switch.
Calculate the maximum possible current in each power wire and
common wire. Observe all electrical codes dictating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately
•You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together
•You should separate input wiring from output wiring
•We advise that you label the wiring to all devices in the system.
Grounding the Moxa EDS-P506E-4PoE Series
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well
-grounded
mounting surface such as a metal panel.
Wiring the Relay Contact
The EDS-P506E-4PoE Series has one set of relay output. This relay
contact uses two contacts of the terminal block on the EDS-P506E-4PoE’s
top panel. Refer to the next section for detailed instructions on how to
connect the wires to the terminal block connector, and how to attach the
terminal block connector to the terminal block receptor. In this section,
we illustrate the meaning of the two contacts used to connect the relay
contact.
FAULT:
The two contacts of the 6
-pin terminal
block connector are used to detect
user
-configured events. The two wires
attached to the
fault contacts form an
open circuit when a user
-configured
event is triggered. If a user
-configured
event does not occur, the
fault circuit
remains closed.

- 8 -
Wiring the Redundant Power Inputs (12/24/48
VDC)
The EDS-P506E-4PoE Series has two sets of power inputs—power input 1
and power input 2. The top and front views of one of the terminal block
connectors are shown here.
STEP 1: Insert the negative/positive DC
wires into the V
-/V+ terminals,
respectively.
STEP 2:
To keep the DC wires from
pulling loose, use a small
flat-blade
screwdriver to tighten the wire
-clamp
screws on the front of the terminal block
connector.
STEP 3:
Insert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on
the
EDS-P506E-4PoE’s top panel.
ATTENTION
Please use a power supply defined by SELV or one that complies
with the double insulation under the UL 60950, UL 61010
-
1, UL
61010-2-201 standards.
Wiring the Digital Inputs
The EDS-P506E-4PoE Series has one set of digital input (DI). The DI
consists of two contacts of the 4-pin terminal block connector on the
EDS-P506E-4PoE 's top panel, which are used for the two DC inputs. The
top and front views of one of the terminal block connectors are shown
here.
STEP 1: Insert the negative
(ground)/positive DI wires into the
┴
/I terminals, respectively.
STEP 2:
To keep the DI wires from
pulling loose, use a small flat
-blade
screwdriver to tighten the wire
-clamp
screws on the front of the terminal block
connector.
STEP 3:
I
nsert the plastic terminal block
connector prongs into the terminal block
receptor, which is located on
the
EDS-P506E-4PoE’s top panel.
Suggested Wire Type for Wiring Relay Contact (R), Digital
Input (DI) and Power Inputs (P1/P2)
The switch includes two 4-pins 5 mm pin-pitch terminal blocks. When
wiring the relay contact (R), digital input (DI) and power inputs (P1/P2),
we suggest using the cable type - AWG (American Wire Gauge) 12-28 and
the corresponding pin type cable terminals.

- 9 -
NOTE
The wire must be able to withstand at least 105°C and the torque
value should be 4.5 lb
-in (0.51 N-m). D
o not use excessive force
when fixing the wiring.
Communication Connections
Each EDS-P506E-4PoE series switch has 4 types of communication ports:
•1 USB console port (type B connector)
•1 USB storage port (type A connector)
•4 10/100 60W PoE+ Ethernet ports
•2 100/1000Base SFP slots
•2 10/100/1000BaseT(X) Ethernet ports
USB Console Connection
The EDS-P506E-4PoE Series has one USB console port (type B connector),
located on the top panel. Use the USB cable (provided in the product
package) to connect the EDS-P506E-4PoE's console port to your PC's USB
port and install the USB driver (available in the software CD) on the PC.
You may then use a console terminal program, such as Moxa PComm
Terminal Emulator, to access the EDS-P506E-4PoE’s console
configuration utility.
USB Console Port (Type B Connector) Pinouts
Pin
Description
1
D– (Data -)
2
VCC (+5V)
3
D+ (Data+)
4
GND (Ground)
USB Storage Connection
The EDS-P506E-4PoE Series has one USB storage port (type A connector)
on the front panel. Use Moxa ABC-02-USB-T automatic backup
configurator to connect the EDS-P506E-4PoE's USB storage port for
configuration backup, firmware upgrade or system log file backup.
ABC-02-USB Installation
Plug the ABC-02-USB into the
USB
storage port of
the Moxa
EDS
-P506E-4PoE Series.
Securing the ABC
-02-USB on
the wall with an M4 screw is
suggested.

- 10 -
USB Storage Port (Type A Connector) Pinouts
Pin
Description
1
VCC (+5V)
2
D– (Data -)
3
D+ (Data+)
4
GND (Ground)
10/100BaseT(x) RJ45 Pinouts
MDI Port Pinouts
MDI-X Port Pinouts
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Pin
Signal
1
Rx+
2
Rx-
3
Tx+
6
Tx-
1000BaseT Ethernet Port Connection
1000BaseT data is transmitted on differential TRD+/- signal pairs over
copper wires.
MDI/MDI-X Port Pinouts
Pin
Signal
1
TRD(0)+
2
TRD(0)-
3
TRD(1)+
4
TRD(2)+
5
TRD(2)-
6
TRD(1)-
7
TRD(3)+
8
TRD(3)-
PoE Ethernet Port Connection
PoE ports located on the EDS switch’s front panel are used to connect to
PoE-enabled devices. The pinout follows the Alternative A mode of
802.3af/802.3at standards and 4-Pair 60W mode. Details are shown
below.
PoE Port Pinouts for 802.3af/802.3at Mode
Pin
Power
1
V+
2
V+
3
V-
6
V-
PoE Port Pinouts for 4-Pair PoE 60W Mode
Pin
Power
1
V+
2
V+
3
V-
4
V+
5
V+
6
V-
7
V-
8
V-