Moxa Technologies ToughNet TN-5516 Series Manual

2010 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802055160013
TN-5516/5518 Series
Hardware Installation Guide
Moxa ToughNet Switch
Fourth Edition, November 2010

f
.
.
s
nsole and relay output.
.
/VAC (88 to 300 VDC, 85 to 264 VAC),
s.
y
e Protocol) for the precise time
nt with different policies.
•Turbo Ring, Turbo Chain,and RSTP/STP (IEEE802.1w/D).
Overview
The ToughNet TN-5516/5518 series M12 managed Ethernet switches are
designed for industrial applications in harsh environments. The TN series
switches use M12 connectors to ensure tight, robust connections, and
guarantee reliable operation against environmental disturbances, such as
vibration and shock. The wide selection of 12/24/36/48 VDC, 72/96/110
VDC, or 110/220 VDC/VAC dual redundant power supplies increases the
reliability of your communications. The TN-5516 switches provide up to
16 fast Ethernet M12 ports.
The TN-5518 switches provide up to 16 fast Ethernet M12 ports, and the
2 ports located on the bottom provide a Gigabit Ethernet interface with
bypass relay option. Models with an extended operating temperature
range of -40 to 75°C are also available. The TN-5516/5518 series
Ethernet switches are compliant with EN50155/50121-3-2/50121-4
(railway applications), NEMA TS2 (traffic control systems), and e-Mark
(vehicles) requirements, making the switches suitable for a variety o
industrial applications.
Package Checklist
Your ToughNet TN-5516/5518 switch is shipped with the following items.
If any of these items is missing or damaged, please contact your
customer service representative for assistance.
•1 Moxa ToughNet switch.
•Hardware installation guide.
•CD-ROM with user’s manual, Windows utility, and SNMP MIB file
•Moxa product warranty statement
•M12 to DB9 console port cable.
r console and relay output port•2 protective caps fo
•Panel mounting kit.
Features
Anti-Vibration Circular Connectors for Robust Links
•M12 D-coding 4-pin female connectors for Fast Ethernet
10/100BaseT(X) ports.
•M12 connectors for Gigabit Ethernet 10/100/1000BaseT(X) ports
•M12 A-coding 5-pin male connectors for co
•M23 6-pin male connector for power input
Dual, Isolated Redundant Power Inputs
•Supports 12/24/36/48 VDC (8.4 to 60 VDC).
•Supports 72/110 VDC (50.4 to 54 VDC), isolated.
•Supports 110/220 VDC
isolated.
•Dual redundant, parallel load-sharing power supplie
High Performance Network Switching Technolog
•IPv6 ready, certified by the IPv6 Logo Committee.
•IEEE 1588 PTP (Precision Tim
synchronization of networks.
•DHCP Option 82 for IP address assignme
•Modbus/TCP industrial Ethernet protocol.
- 2 -

•IGMP Snooping and GMRP for filtering multicast traffic from industria
Ethernet protocols. l
.
.
.
.
.
t
.
r
P
stallable M12 D-coded screw-in connector,
llable M12 A-coded screw-in connector,
DK-DC50131: DIN-Rail mounting kit, 50 x 131 mm.
•Port-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease
network planning.
•QoS (IEEE802.1p/1Q and TOS/DiffServ) to increase determinism
•802.3ad, LACP for optimum bandwidth utilization.
•IEEE802.1X and https/SSL to enhance network security.
•SNMP v1/v2c/v3 for different levels of network management.
•RMON for efficient network monitoring and proactive capability
•Bandwidth management prevents unpredictable network status
•Lock port allows access by only authorized MAC addresses
•Port mirroring for online debugging.
•Automatic warning by exception through email, relay output
•Automatic recovery of connected devices’ IP addresses.
•Line-swap fast recovery.
•LLDP for automatic topology discovery through network managemen
software.
•Configurable through Web browser, Telnet/Serial console, and
Windows utility.
Designed for Industry-specific Applications
•Two Gigabit Ethernet ports to meet high bandwidth requirements.
•Bypass relay option on the 2 Gigabit Ethernet ports ensure non-stop
data communication in the event the switch stops working due to a
power failure .
•Three rotary switches for setting the last 3 digits of the IP address
makes maintenance even easier. a•EN 50155/50121-3-2/50121-4, NEMA TS2, and e-Mark compli
•e (for “-T” models). nt -40 to 75°C operating temperature rang
•IP54/IP67, rugged high-strength case.
•Panel mounting or DIN-Rail mounting installation capability.
Recommended Optional Accessories
•CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin powe
cable with IP67-rated female 6-pin M23 connector.
•CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UT
Ethernet cable with IP67-rated male 4-pin M12 D-coded connector.
•CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable
with IP67-rated female 5-pin M12 A-coded connector.
•M12D-4P-IP68: Field-in
male 4-pin, IP68-rated.
•M12A-5P-IP68: Field-insta
female 5-pin, IP68-rated.
•CAP-M12F-M: Metal cap for M12 female connector
•
- 3 -

TN-5516 Panel Layouts
15
17
16
17
Botton View
Rear View
1
22
3
4
5
6
7
8 9 10 11 12
13
14
18
19
.
hielded M23 connector).
for power input 2.
ad.
ler or chain tail.
aseT(X) port (female 4-pin shielded M12 connector with D
ver with Model name1. 3 Rotary switches and protective co
r panel mounting kit.2. Screw holes fo
3. Console port.
4. Grounding screw.
5. Relay output port.
6. Power input voltage range indication.
7. Power input port (male 5-pin s
8. PWR1 LED: for power input 1.
9. PWR2 LED:
10. FAULT LED.
11. MSTR/HEAD LED: for ring master or chain he
12. CPLR/TAIL LED: for ring coup
13. TP port’s 10/100 Mbps LED.
14. 10/100B
coding).
15. Waterproof vent.
.
E1 LED: Not used by the TN-5516 series.
16. Product label.
17. 12 Screw holes for DIN-Rail mounting kit.
18. E2: LED: Not used by the TN-5516 series
19.
- 4 -

TN-5518 Panel Layouts
ve1. 3 Rotary switches and protective co
r panel mounting kit. r with Model name.
for power input 2.
ad.
ler or chain tail.
aseT(X) port (female 4-pin shielded M12 connector with D
2. Screw holes fo
3. Console port.
4. Grounding screw.
5. Relay output port.
6. Power input voltage range indication.
hielded M23 connector).7. Power input port (male 5-pin s
8. PWR1 LED: for power input 1.
9. PWR2 LED:
10. FAULT LED.
11. MSTR/HEAD LED: for ring master or chain he
12. CPLR/TAIL LED: for ring coup
13. TP port’s 10/100 Mbps LED.
14. 10/100B
coding).
15. Waterproof vent.
- 5 -

16. Product label.
17. 12 Screw holes for DIN-Rail mounting kit. .
.
18. E2 LED: Down-side E2 Gigabit port's 10/100/1000 Mbps LED
19. E1 LED: Down-side E1 Gigabit port's 10/100/1000 Mbps LED
20. Gigabit Ethernet port E1 (corresponding to port 17 in the TN-5518
User's Manual).
21. Gigabit Ethernet port E2 (corresponding to port 18 in the TN-5518
User's Manual).
ATTENTION
DO NOT open or remove the vent (#15). Once the seal has bee
removed, the warranty becomes invalid. n
e
.
Exposed connectors (including 3, 5, and 14) when not in use
must be tightly covered with protective caps (an optional
accessory) to ensure IP54/IP67-rated protection.
After the rotary switches (1) are set, the protective cover must b
properly affixed to ensure IP54/IP67-rated protection
- 6 -

Mounting Dimensions (unit = mm)
TN-5516 Series
69.80
67.70
52.70
DIN-RAIL KIT
o8.00
DIN-RAIL KIT
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
M4
235.00
220.00
175.80
120.00
170.00 120.00
250.00
21.00
21.00
37.00
177.00
37.00
o4.50
8.00
- 7 -

TN-5518 Series
Panel/Wall Mounting
1:
Mounting the TN-5516/5518 to a wall requires 4 screws. Use the
Net switch as a guide to mark the correct positions of the 4 screws.
2:
he 4 screws in the panel mounting kit. If you
ld like to use your own screws, make sure the
screw head is between 6.0 mm and 7.0 mm in
ameter and the shaft is less than 4.0 mm in
meter, as shown at the right.
ew the screws in all the way—leave a space of about 2 mm to
allow room for sliding the ToughNet switch between the wall and the
ws.
STEP
Tough
STEP
Use t
6.0 - 7.0 mm
< 4.0 mm
wou
di
dia
Do not scr
scre
- 8 -

NOTE Before tightening the screws into the wall, make sure the screw
head and shaft size are sui
one of the keyhole-shapedtable by inserting the screw through apertures of the ToughNet sw
itch.
STEP 3:
Once the screws are fixed in the wall, hang the ToughNet switch on the 4
screws through the large opening of the keyhole-shaped apertures, and
then slide the switch downwards. Tighten the four screws for added
stability.
NOTE To provide greater protection from vibrations and shocks, use
screws with shaft diameter between 6.0 mm and 7.0 mm, and fix
the ToughNet switch onto the wall directly through the large
opening of the keyhole-shaped apertures.
DIN-Rail Mounting (optional)
With the optional DIN-Rail
mounting kit DK-DC50131 (must be
purchased separately), you can
mount the TN-5516/5518 on a
35mm DIN-Rail.
Use 12 screws (6 screws per plate)
STEP 1:
to atta ail
attach e rear pane
of the
ch the two DIN-R
ment plates to th l
Recessed button
switch.
Spring-loaded bracket
STEP
If the s n
to rele e
spring down a few millimeters in each
directio
2:
pring-loaded bracket is locked in place, push the recessed butto
ase it. Once released, you should feel some resistance from th
as you slide the bracket up and
n.
- 9 -

STEP 3:
Positio itch on then the ToughNet sw
DIN-R lamps oveail, tilting to hook c
r
the top
STEP 4:
Swing the switch down fully onto the
edge of the rail.
DIN-Rail, until both clamps
completely latch.
DIN-Rail
DIN-Rail
everse Step 3 and 4
To remove the Moxa ToughNet Switch from the DIN-Rail, use a
screwdriver to pull out the two spring-loaded brackets from the bottom
until they are fixed in the “locked” position. Then r
above.
DIN-Rail
Wiring Requirements
WARNING
Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label. Check
the voltage of your power source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by a SELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa switch.
This device has UL508 approval. Use copper conductors only,
60/75°C, and tighten to 4.5 pound-inches. For use in pollution
degree 2 environments.
- 10 -

ATTENTION
Safety First!
Observe all electrical codes dictating the maximum current
allowable for each wire size. If the current goes above the
maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
Please read and follow these guidelines:
•Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with different
You can us type of si nsmitted through a wire to
de sh is
th si
bundled together.
•Keep input wiring and ou
It i t stem
wh
Grounding the Tough
oun ting h
electromagnetic interference
grounding screw to the groun
signal characteristics should be routed separately.
•e the
termine which gnal tra ould be kwires
at wiring that shares ept separate. The rule of thumb milar electrical characteristics can be
tput wiring separated.
you label wiring for all•s strongly advised tha
en necessary. devices in the sy
Net Switch
Gr ding and wire rou elp limit the effects of noise due to
(EMI). Run the ground connection from the
ding surface prior to connecting devices.
ATTENTION
This product is in
mounting surfacetended to be mounted to a well-grounded such as a metal panel.
- 11 -

Connecting the Power Supplies
the TN-5516/5518.
The ToughNet TN-5516/5518 series switches support two sets of power
supplies—power input 1 and power input 2. The M23 6-pin male
connector on the TN-5516/5518 front panel is used for the dual power
inputs.
Pinouts for the power input port on
Pinouts for the p wer input port on the TN-5516/5518.
scription Usage
o
Pin De
1 PWR1 Live / DC + Connect “PWR1 Live / DC +” to the Liveterminal when using an AC power source
or to the positive (+) terminal when using
a DC power source.
2 PWR1 Neutral / DC -
Connect “PWR1 Neutral / DC –“to the
Neutral terminal when using an AC power
source or to the negative (-) terminal
ing a DC power source.when us
3 Chassis Ground Connect the “Chassis Ground” to the
C inputs or tosafety ground terminal for A
the equipment ground bus for DC inputs.
4 PWR2 Neutral / DC -
Connect “PWR2 Neutral / DC –”to the
Neutral terminal when using an AC power
source or to the negative (-) terminal
when using a DC power source.
5 PWR2 Live / DC + Connect “PWR2 Live / DC +” to the (Live)
terminal when using an AC power source
or to the positive (+) terminal when usi ng
a DC power source.
STEP 1:
Plug your power cord connector to the power input port o
TN-5516/5518 switch.
STEP 2:
f the
Screw the nut on your power cord connector to the power input connector
on the switch to ensure a tight connection.
ATTENTION
Before connectin TN-5516/5518 to the power input, make
sure the power so ltage is stable.
g the
urce vo
- 12 -

Connecting the Relay Outputs
Each TN-5516/5518 switch has two sets of relay outputs—relay output 1
and relay output 2.The M12 A-coded 5-pin male connector on the
TN-5516/5518 front panel is used for the two relay outputs. Use a power
cord with an M12 A-coded 5-pin female connector to connect the relay
contacts. You can purchase an M12 power cable from Moxa; the model
number is CBL-M12 (FF5P)/OPEN-100 IP67.
Pinouts for the relay output port on TN-5516/5518.
N.C.: Not connected
FAULT:
The two sets of relay contacts of the M12 A-coded 5-pin male connector
are used to detect user-configured events. The two wires attached to the
fault contacts form an open circuit when a user-configured ev nt is
triggered. If a user-configured event does not occur, the fault circuit
cting the Data Lines
10/100BaseT(X) Ethernet Port Connection
All TN-5516/5518 models have 16 10/100BaseT(X) Ethernet ports (4-pin
shielded M12 connector with D coding). The 10/100TX ports located on
the TN-5516/5518 front panel are used to connect to Ethernet-enabled
devices. Most users configure these ports for Auto MDI/MDI-X mode, in
which case the port’s pinouts are adjusted automatically depending on
the type of Ethernet cable used (straight-through or cross-ove ), and the
type of device (NIC-type or HUB/Switch-type) connected to the port.
X
straight-through and cross-over Ethernet cables.
Pinouts for the 10/100BaseT(X) Ports on the
TN-5516/5518.
e
remains closed.
Conne
r
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-
(HUB/Switch-type) ports. We also give cable wiring diagrams for
Housing: shield
- 13 -

Pinouts for the 10/100/1000BaseT(X) M12 (8-pin) Port
M12 (4-pin, M) to M12 (4-pin, M) Cross-Over Cable Wiring
Tx+
Rx+
Cross-Over Cable Wiring
1
2 1 2
Tx-
Rx- 3 43 4
Tx+
Rx+
Tx-
Rx-
M12 ( 12 (4-pin, M) Straight-Trough Cable4-pin, M) to M
Wiring
Tx+
Rx+
Tx-
Straight-through Cable Wiring
1
2
3
1
2
Rx- 4 4
3
Rx+
Tx+
Rx-
Tx-
M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring
Tx+
Rx+
Tx- 2 3
Rx- 4 6
Cross-Over Cable Wiring
11
2
3
Tx+
Tx-
Rx+
Rx-
- 14 -

M12 (4-pin, M) to RJ45 (8-pin) Straight-Trough Cable
Wiring
Tx+
Rx+
Tx-
Rx-
1
2
3
4
1
2
3
6
Straight-through Cable Wiring
Rx+
Rx-
Tx+
Tx-
The ToughNet TN-5516/5518 switches have 3 rotary switches on the
front panel for configuring the IP address without using a PC, making
onsite co n ext nven s can ally helpful
when you need to replace a faulty switch quickly.
STEP 1: Remove the protective cover by unscrewing the 2 screws with an
Allen wrench (also called an Allen key or hex key).
STEP 2: Use a flat-bladed screwdriver to rotate the 3 rotary switches to
point to the chosen numbers.
Rotary Switch IP Address Settings
nfiguratio remely co ient. Thi be especi
STEP 3: Replace the protective cover and then tighten the screws to the
proper torque.
STEP 4: Restart the ToughNet switch to enable the newly configured IP
address.
NOTE 1. “Hardware-based IP configuration” only supports IPv4
address settings.
2. “Hardware-based IP configuration”
is enabled only when the
3 rotary switches are set to values ranging from 001 to 254
The ToughNet switch’s IP address will be configured as
“192.168.127.xxx”, where “xxx” are valid value numbers
.
set by the rotary switches.
3. When enabled, “Hardware-based IP configuration”
overrides the “Auto IP Configuration” described in the “IP
Settings” section in the user’s manual.
4. Disable “Hardware-based IP configuration” by setting the 3
rotary switches to 000 (the factory default).
5. If the rotary switch numbers are set to an invalid
combination (255 to 999), the ToughNet switch will use the
fixed IP address 192.168.127.253 by default.
ATTENTION
The protective cover must be fixed properly to ensure IP54/IP67
protection. Use a torque wrench set to a torque of 4 kgf-m when
tightening the screws. Note that applying a larger torque may
damage the plastic protective cover.
- 15 -

Bypass Relay Function
g normally,
two ort as the other ports. That is,
ingre rwarded. In the event the
stops
gered to p
The figure below illust the b
Switch B loses power, then the tw s will be bypassed through
y circ nsmis
transmission line from Switch B t nterconnect automatically; this
way there is no stoppa
ss re i elps t
in a li .
With the maximum segment leng
100 meters, cable length must b
that utilizes this function exam
Switch A to B and from mu
if the two adjacent nodes (switch
here w e the
-to-B C-to-
The bypass relay function works
ToughNet™ switches with bypass not recommended to
be used in networks th ork loops
may occur when redun prot are
applied.
The TN-5518-2GTXBP models’ two Gigabit Ethernet ports are equipped
with a bypass relay function. When the switch is operatin
these
frame Gigabit p ssions are pr
s work in
oce the same way ssed and then fo
wswitch
be trig working due to a po ensure n er failure, the bypass relay function will data communication.on-sto
rates ypass relay function. For example, if
o Gigabit port
the rela uit and the tra sion line from Switch A to B and the
o C will i
ge.
The bypa
failures lay funct near topoon h logy he network recover from single-node
th of category 5 twisted-pair cable being
e considered when designing a network
m
Switch A itch BSw
Switch C
Switch D
Bypassing
. For
B to C ple, the total length of the cables fro st be no more than 100 meters. This way,
B and C for example) encounter a power
, provided that the tofailure, t
cables A ill be no st , B-to-C, oppag and tal length of D are no more than 100 meters.
best for networks with linear topologies.
relay function are
at employ ring topologies because netw
dancy ocols such as RSTP or TurboRing™
- 16 -

LED Indicators
dicators are located on the ToughNet switch’s front panel.
n of each LE e below.
Several LED in
The functio D is described in the tabl
LED Color State
Description
System LEDs
ON Power is being supp
PWR1. lied to power inputPWR1 AMBER
OFF Power is not bein
input PWR1 g supplied to power
ON Power is being supplie
PWR2. d to power inputPWR2 AMBER
OFF Power is not being supplied to power
input PWR2.
ON When the corresponding PORT alar
enabled, and a user-configured ev m is ent is
triggered.
FAULT RED
PORT alarm is
event is
ing PORT alarm is disabled.
OFF When the corresponding
enabled and a user-configured
not triggered, or when the
correspond
ON When
the TN switch is either the Master
of this Turbo Ring, or the Head of this
Turbo Chain.
Blinking
When the TN switch is Ring Master of
this Turbo Ring and the Turbo Ring is
broken, or it is Chain Head of this Turbo
Chain and the Turbo Chain is broken.
MSTR/
HEAD GREEN
When the TN switch is neither the
Master of this Turbo Ring, nor the Head
OFF
of this Turbo Chain.
ON When the TN switch enables the
coupling function to form a back-up
g, or it is the Tail ofpath in this Turbo Rin
this Turbo Chain.
Blinking
When Turbo Chain is down.
CPLR/
TAIL GREEN
witch disables the
Ring, or it is
OFF When the TN s
coupling function of Turbo
not the Tail of the Turbo Chain.
Ports LEDs
ON TP port’s 10 Mbps link is active.
Blinking
Data is being transmitted at 10 Mbps.
AMBER
Off TP port’s 10 Mbps link is inactive.
On TP port’s 100 Mbps link is active.
Blinking
Data is being transmitted at 100 Mbps.
TP
EEN
off TP port’s 100 Mbps link is inactive.
(10/100M)
GR
On TP port’s 10 or 100 Mbps link is active.E1/E2 AMBER
Blinking
Data is being transmitted at 10 or 100
Mbps.
(
Off TP port’s 10 or 100 Mbps link is inactive.
On TP port’s 1000 Mbps link is active.
Blinking
Data is being transmitted at 1000 Mbps.
10/100/
GREEN
Off TP port’s 1000 Mbps link is inactive.
1000M)
- 17 -

Specifications
Technology
Standards
ies
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X)
IEEE 802.3ab for 1000BaseT(X) (TN-5518 ser
only)
IEEE 802.3x for Flow Control
IEEE 802.1D for Span
IEEE 802.1w for Rapid STP
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.1X for Aut
ning Tree Protocol
cationhenti
IEEE 802.3ad for Port Trunk with LACP
Protocols ion
TP, SMTP, RARP,
nt, SSH, Syslog, LLDP,
IGMP v1/v2 device, GMRP, GVRP, SNMP
v1/v2C/v3, DHCP Server/Client, DHCP Opt
66/67/82, BootP, TFTP, SN
P, HTTPS, TeleRMON, HTT
IEEE 1588 PTP, Modbus/TCP, IPv6
MIB MIB-II,
Q-BRIDGE M
Ethernet-like MIB, P-BRIDGE MIB,
IB, Bridge MIB, RSTP MIB, RMON
IB Group 1, 2, 3, 9M
Flow Control IEEE802.3x flow control, back pressure flow
control
Switch Properties
Priority Queues 4
Max. Number of
Available VLANs 64
VLAN ID Range VID 1 to 4094
IGMP Groups 256
Interface
Fast Ethernet ctor, 10/100BaseT(X)
auto negotiation speed, F/H duplex mode, and
Front cabling, M12 conne
auto MDI/MDI-X connection
Gigabit Ethernet negotiation speed,
DI-X connection,
and bypass relay option
Down cabling, M12 connectors,
10/100/1000BaseT(X) auto
F/H duplex mode, auto MDI/M
Console Port M12 A-coding 5-pin male connector
System LED Indicators
PWR1, PWR2, FAULT, MSTR/HEAD, CPLR/TAIL
Port LED Indicators 000M10/100M (fast Ethernet port), 10/100/1
(Gigabit Ethernet port)
Alarm Contact 2 A-coding 5-pin
t carrying capacity of
Two relay outputs in one M1
male connector with curren
3 A @ 30 VDC or 3 A @ 240 VAC
Rotary Switches the IP addressFor setting the last 3 digits of
- 18 -

Power Requirements
Input Voltage LV: 12/24/36/48 VDC (8.4 to 60 VDC)
96/110 VDC (50.4 to 154 VDC)
, 85 to
264 VAC)
MV: 72/
HV: 110/220 VDC/VAC (88 to 300 VDC
Input Current TN-5516 Series:
0.338 A @ 24 VDC, 0.133 A @ 72 VDC,
0.089 A @ 110 VDC, 0.270 A @ 110 VAC,
0.170 A @ 220 VAC
TN-5518-2GTX Series:
0.635 A @ 24 VDC, 0.28 A @ 72 VDC,
0.19 A @ 110 VDC,0.37 A @ 110 VAC,
0.238 A @ 220 VAC
TN-5518-2GTXBP Series:
0.667 A @ 24 VDC, 0.296 A @ 72 VDC,
0.202 A @ 11 VDC,0.387 A @ 110 VAC,
0.244 A @ 220 VAC
Connection M23 6-pin male connector
Overload Current
Protection Present
Reverse Polarity
Protection Present
Physical Characteristics
Housing Metal, IP54 protection (with protective caps on
unused ports)
Dimensions (W H D)
TN-5516 Series:
250 x 170 x 69.8 mm (9.84 x 6.69 x 2.75 in)
TN-5518 Series:
250 x 183 x 69.8 mm (9.84 x 7.20 x 2.75 in)
Weight TN-5516 Series: 2500g
TN-5518 Series: 2550 g
Installation Panel mounting, DIN-Rail mounting
(with optional kit)
Environmental Limits
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Humidity 5 to 95% (non-condensing)
Regulatory Approvals
Safety UL508 (Pending)
Rail Traffic EN50155, EN50121-3-2, EN50121-4 (Pending)
Road Traffic NEMA TS2 (Pending), e-Mark (Pending)
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), level 3
vel 3
EN61000-
61000-
61000-
61000-
EN61000-4-3 (RS), level 4
3EN61000-4-4 (EFT), level
EN61000-4-5 (Surge), le
4-6 (CS), level 3
EN 4-8
EN 4-11
EN 4-12
Shock IEC61373
Free ll IEC6fa 0068-2-32
Vibration IEC61373
- 19 -

- 20 -
Note: Please check Moxa’s website for the most up-to-date
certification status.
WARRANTY 5 years
Details: See www.moxa.com/warranty
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: [phone]
Fax: [phone]
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: [phone]
Fax: [phone]
Moxa Europe:
Tel: [phone]
Fax: [phone]
Moxa Asia-Pacific:
Tel: [phone]
Fax: [phone]