Moxa Technologies IKS-6726-8PoE Series Manual

– 1 – – 2 – – 3 –
P/N: 1802067260022
IKS-6726-8PoE Series
Hardware Installation Guide
Third Edition, July 2011
Package Checklist
The Moxa IKS-6726-8PoE series industrial rackmount switches are
shipped with the following items. If any of these items are missing
or damaged, please contact your customer service representative
for assistance.
•IKS-6726-8PoE switch
•RJ45 to DB9 console port cable
•Protective caps for unused ports
•2 rackmount ears
•Documentation and software CD
•Hardware installation guide (printed)
•Warranty card
Physical Appearance
Panel Layouts
1. System status LEDs
2. Mode LEDs for the interface module
3. Port LEDs for the interface module
4. Push-button switch for selecting the mode of the interface
module
5. Model name
6. 10/100BaseT(X) port
7. 10/100BaseT(X) PoE port
8. Fast Ethernet / PoE interface module
9. Gigabit Ethernet interface module
10. Serial console port
11. 10-pin terminal block for power inputs and relay output
12. Rack mounting brackets
Dimensions (unit=mm)
Fast Ethernet, PoE Interface Modules (for slot 1)
Gigabit Ethernet Interface Modules (for slot 2)
Rack Mounting
Use four screws to attach the
switch to a standard rack.
Wiring Requirements
WARNING
Be sure to disconnect the power cord before installing
and/or wiring your Moxa industrial rackmount switch.
Calculate the maximum possible current in each power wire
and common wire. Observe all electrical codes dict
ating the
maximum current allowable for each wire size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your
equipment.
Grounding the Rackmount Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection
from the ground screw to the grounding surface prior to connecting
devices.
Wiring the Power Inputs
The IKS series switches support dual redundant power supplies:
Power Supply 1 (PWR1) and Power Supply 2 (PWR2). The
connections for PWR1, PWR2, and the RELAY are located on the
terminal block. The front view of the terminal block connectors is
shown below.
Wiring the Relay Contact
Each IKS switch has one relay
output. Refer to the next section
for detailed instructions on how
to connect the wires to the
terminal block connector, and how to attach the terminal block
connector to the terminal block receptor.
FAULT: The relay contacts of the 10-pin terminal block connector
are used to detect user-configured events. The two wires attached
to the RELAY contacts form an open circuit when a user-configured
event is triggered. If a user-configured event does not occur, the
RELAY circuit will be closed.
Wiring the Redundant Power Inputs
Each IKS switch has two sets of
power inputs: power input 1 and
power input 2.
STEP 1: Insert the dual set positive/negative DC wires into PWR1
and PWR2 terminals (+ pins 1, 9; - pins 2, 10), or insert the
L/N AC wires into PWR1 and PWR2 terminals (L pin 1, 9; N pin
2,10).
STEP 2: Use a screwdriver to tighten the wire-clamp screws on the
front of the terminal block connector.
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-9021-Moxa-IKS-6726-8PoE-F-48-T-Managed-Switch.aspx

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2011 Moxa Inc., All Rights Reserved
LED Indicators
System LEDs
STAT
GREEN On System has passed self-diagnosis test on boot-
up
and is ready to run.
Blinking System is undergoing the self-diagnosis test.
RED On System failed self-diagnosis on boot-up.
PWR1
AMBER
On Power is being supplied to the main module’s
power input PWR1.
Off Power is not being supplied to the main module’s
power input PWR1.
PWR2
AMBER
On Power is being supplied to the main module’s
power input PWR2.
Off Power is not being supplied to the main module’s
power input PWR2.
FAULT
RED
On The corresponding PORT alarm is enabled and a
user-configured event has been triggered.
Off
The corresponding PORT alarm is enabled and a
user-
configured event has not been triggered, or
the corresponding PORT alarm is disabled.
MSTR/HEAD
GREEN
On
This IKS switch is the Master of this Turbo Ring or
the Head of this Turbo Chain.
Blinking
This IKS switch has become Ring Master of this
Turbo Ring after the Turbo Ring was broken, or
Chain Head of this Turbo Chain after the Turbo
Chain was broken..
Off
This IKS switch is neither the Master of this Turbo
Ring nor the Head of this Turbo Chain.
CPLR/TAIL
GREEN On When this IKS switch enables the coupling or
tailing function to form a back-up path.
Off When this IKS switch disables the coupling and
tailing function.
Mode LEDs
LNK/ACT
GREEN
On The corresponding module port’s link is active.
Blinking The corresponding module port’s data is being
transmitted.
Off The corresponding module port’s link is inactive.
SPEED
GREEN
Off The corresponding module port’s data is being
transmitted at 10 Mbps.
On The corresponding module port’s data is being
transmitted at 100 Mbps.
Blinking
The corresponding module port’s data is being
transmitted at
1000 Mbps.
FDX/HDX
GREEN
On The corresponding module port’s data is being
transmitted in full duplex mode.
Off The corresponding module port’s data is being
transmitted in half duplex mode.
RING PORT
GREEN
On The corresponding module’
s port is the ring port
of this IKS switch.
Off The corresponding module’s port is not the ring
port of this IKS switch.
COUPLER PORT
GREEN
On The corresponding module’s port is the coupler
port of this IKS switch.
Off The corresponding module’s port is not the
coupler port of this IKS switch.
PoE Module LEDs
POE
AMBER On The corresponding port is supplying power
Off The corresponding port is not supplying power
Specifications
Technology
Standards IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x,
802.1D, 802.1W, 802.1Q, 802.1p, 802.1X,
802.3ad
Flow control IEEE 802.3x flow control, back pressure flow
control
Interface
Fast Ethernet
Slot 1 for any combination of 4, 6, 7, or 8-port
PM-7200 fast Ethernet modules with
10/100BaseT(X) (TP/PoE/M12 interface),
100BaseFX (SC/ST connector), or 100BaseSFP
Gigabit Ethernet
Slot 2 for 2-port PM-7200 Gigabit Ethernet
combo module with 10/100/1000BaseT(X),
1000Base SFP slots (SFP slot, LC connector)
Alarm Contact One
relay output with current carrying capacity
of 3A @ 30 VDC or 3A @ 240 VAC
Optical Fiber (100BaseFX)
Distance
Multi-mode
0 to 5 km, 1300 nm (50/125μm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125μm, 500
MHz*km)
Single-mode
0 to 40 km, 1310 nm (9/125μm, 3.5
PS/(nm*km))
Min. TX Output Multi-mode: -20 dBm; single-mode: -5 dbm
Max. TX Output Multi-mode: -10 dBm; single-mode: 0 dbm
RX Sensitivity Multi-mode: -32 dBm; single-mode: -34 dbm
Power
Input Voltage 48 VDC (44 to 57V) or 110/220 VDC/VAC (88 to
300 VDC, 85 to 264 VAC)
Input Current
Max. 1.5/0.75 A @ 110/220 VDC (with 8 fully
loaded PoE ports)
Max. 1.6/0.8 A @ 110/220 VAC (with 8 fully
loaded PoE ports)
Max. 5.73 A @ 48 VDC (with 16 fully loaded
PoE
ports)
Max. PoE Power
Output
IKS-6726-8PoE-48-T:
Max.15.4 W per PoE port
Max. 240 W total for PoE output
IKS-6726-8PoE-HV-T:
Max.15.4 W per PoE port
Max. 120 W total for PoE output
Physical Characteristics
Housing IP 30 protection, metal case
Dimensions 440 x 44 x 325 mm (17.32 x 1.73 x 12.80 in.)
Weight
IKS-6726-8PoE-F-48-T: 4260 g
IKS-6726-8PoE-F-48-48-T: 4460 g
IKS-6726-8PoE-F-HV-T: 6100 g
IKS-6726-8PoE-F-HV-HV-T: 6500 g
Installation 19” rack mounting
Regulatory Approvals
Safety EN 60950-1 (Pending)
Road Traffic NEMA TS2 (Pending)
Rail Traffic EN 50121-4 (Pending)
EMI FCC Part 15 Subpart B Class A, EN 55022 Class A
Environmental Limits
Operating Temp. -40 to 75°C (-40 to 167°F)
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity. 5 to 95% (non-condensing)
Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty
RSPSupply - 1-888-532-2706 - www.RSPSupply.com
http://www.RSPSupply.com/p-9021-Moxa-IKS-6726-8PoE-F-48-T-Managed-Switch.aspx