Moxa Technologies PT-7728 Series Manual

— 1 — — 2 — — 3 —
PowerTrans Switch
PT-7728/7828 Series
Hardware Installation Guide
Third Edition, May 2008
Package Checklist
The Moxa PowerTrans switch is shipped with the following items. If any
of these items are missing or damaged, please contact your customer
service representative for assistance.
y1 Moxa PowerTrans Switch
yHardware Installation Guide
yCD-ROM with User’s Manual and SNMP MIB file
yMoxa Product Warranty Statement
yRJ45 to DB9 console port cable
yProtective caps for unused ports
y2 rack-mount ears
Panel Layouts
LNK/ACT SPEED FDX/HDX
FAULT MASTER COUPLER
STAT PWR1 PWR2
RINGPORT COUPLER
PORT
MODE
37
4 8
26
15
37
48 2 6
15
4
3
2
1
37
482 6
15
M1
M2
M3
M4
LNK/ACT SPEED FDX/HDX
FAULT MASTER COUPLER
STAT PWR1 PWR2
RINGPORT COUPLER
PORT
MODE
3 7
4 82 6
15
37
4 82 6
15
4
32
1
3 7
48
26
1 5
M1
M2
M3
M4
1
2
3
4
5
6
7
8
M3
PT-7728
M4
1
2
3
4
4
1
3
2
135
246
M1
TX RX TX RX TX RX
246
135
M2
TX RX TX RX TX RX
PT-7728
Front view (Front Cabling)
Front view (Rear Cabling)
Rear view (Front Cabling)
Rear view (Rear Cabling)
8
76
42
3
1
510
9
STAT
FAULT
PWR1
MASTER
PWR2
COUPLER
LNK/ACT SPEED FDX/HDX
RINGPORT COMUPLER
PORT
MODE
PT-7728
1
3
2
4
2
1
4
3
13
24
57
68
13 5
6
TX RX
7
24
1
2
3
4
5
6
M4M3M2M1 PT-7728
CONSOLE
1. System status LEDs
2. Interface Module mode LEDs
3. Interface Module port LEDs
4. Push-button switch to select mode for Interface Module
5. Model Name
6. Fast Ethernet Interface Modules
7. Gigabit Ethernet Interface Modules
8. Serial Console port
9. 10-pin terminal block for power inputs, and relay output
10. Rack Mounting Kit
Dimensions (unit = mm)
Fast Ethernet Interface Modules (for slots 1, 2, and 3)
96.8
40.7
40.7
96.8
96.8
40.7
40.7
96.8
96.8
40.7
96.8
40.7
40.7
96.8
96.8
40.7
PM-7200-6MSC/PM-7200-6SSC
PM-7200-8TX PM-7200-1LSC6TX
PM-7200-2MSC4TX/PM-7200-2SSC4TX
PM-7200-4MSC2TX/PM-7200-4SSC2TX
PM-7200-6MST PM-7200-2MST4TX
PM-7200-4MST2TX
Gigabit Ethernet Interface Modules (for slot 4)
40.7
86.6
86.6
40.7
PM-7200-4GTXSFP PM-7200-2GTXSFP
Rack Mounting
Use four screws to attach the PT switch to a standard rack.
Wiring Requirements
WARNING
Safety First!
Be sure to disconnect the power cord before installing
and/or wiring your Moxa PowerTrans Switch.
Calculate the maximum possible current in each power
wire and common wire. Observe all electrical codes
dictating the maximum current allowable for each wire
size.
If the current goes above the maximum ratings, the wiring
could overheat, causing serious damage to your equipment.
Grounding the Moxa PowerTrans Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
ground screw to the grounding surface prior to connecting devices.
Wiring the Power Inputs
The PT series of switches supports dual redundant power supplies:
“Power Supply 1 (PWR1)” and “Power Supply 2 (PWR2)”. The
connections for PWR1, PWR2 and the RELAY are located on the
terminal block. The front view of the terminal block connectors are
shown below.
Wiring the Relay Contact
Each PT switch has one relay output. Refer to the next section for
detailed instructions on how to connect the wires to the terminal block
connector, and how to attach the terminal block connector to the terminal
block receptor.
P/N: 1802077280012

— 4 — — 5 — — 6 —
FAULT: The relay contact of the 10-pin terminal block connector are
used to detect user-configured events. The two wires attached to the
RELAY contacts form an open circuit when a user-configured event is
triggered. If a user-configured event does not occur, the RELAY circuit
will be closed.
Wiring the Redundant Power Inputs
Each PT switch has two
sets of power inputs:
power input 1 and power
input 2.
STEP 1: Insert the dual set positive/negative DC wires into PWR1 and
PWR2 terminals (+ →pins 1, 9; - →pins 2, 10). Or insert the L/N AC
wires into PWR1 and PWR2 terminals (L →pin 1, 9; N →pin 2,10)
STEP 2: To keep the DC or AC wires from pulling loose, use a
screwdriver to tighten the wire-clamp screws on the front of the terminal
block connector.
LED Indicators
The front panel of the PT switch contains several LED indicators. The
function of each LED is described in the table below.
LED Color State Description
System LEDs
On System has passed self-diagnosis
test on boot-up and is ready to run.
GREEN
Blinking System is undergoing the
self-diagnosis test.
STAT
RED On
System failed self-diagnosis on
boot-up.
On Power is being supplied to the
main module’s power input PWR1.
PWR1 AMBER
Off Power is not being supplied to the
main module’s power input PWR1.
On Power is being supplied to the
main module’s power input PWR2.
PWR2 AMBER
Off Power is not being supplied to the
main module’s power input PWR2.
On
The corresponding PORT alarm is
enabled and a user-configured
event has been triggered.
FAULT RED
Off
The corresponding PORT alarm is
enabled and a user-configured
event has not been triggered, or the
corresponding PORT alarm is
disabled.
On This PT switch is the Master of
this Turbo Ring.
Blinking
This PT switch has become Ring
Master of this Turbo Ring after the
Turbo Ring was broken.
MASTER GREEN
Off This PT switch is not the Master of
this Turbo Ring.
On
When this PT switch enables the
coupling function to form a
back-up path.
COUPLER GREEN
Off When this PT switch disables the
coupling function.
Mode LEDs
On The corresponding module port’s
link is active.
Blinking The corresponding module port’s
data is being transmitted.
LNK/ACT GREEN
Off The corresponding module port’s
link is inactive.
Off
The corresponding module port’s
data is being transmitted at 10
Mbps.
On
The corresponding module port’s
data is being transmitted at 100
Mbps.
SPEED GREEN
Blinking
The corresponding module port’s
data is being transmitted at
1000 Mbps.
On
The corresponding module port’s
data is being transmitted in full
duplex mode.
FDX/HDX GREEN
Off
The corresponding module port’s
data is being transmitted in half
duplex mode.
On The corresponding module’s port
is the ring port of this PT switch.
RING
PORT GREEN
Off
The corresponding module’s port
is not the ring port of this PT
switch.
On
The corresponding module’s port
is the coupler port of this PT
switch.
COUPLER
PORT GREEN
Off
The corresponding module’s port
is not the coupler port of this PT
switch.
Specifications
Technology
Standards IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x,
802.1D, 802.1W, 802.1Q, 802.1p, 802.1X, 802.3ad
Flow control IEEE 802.3x flow control, back pressure flow
control
Interface
Fast Ethernet 10/100BaseT(X) or 100BaseFX (SC/ST connector)
Gigabit Ethernet 10/100/1000BaseT(X), 1000BaseSX/LX/LHX/ZX
(SFP slot, LC connector)
System LED
Indicators
STAT, PWR1, PWR2, FAULT, MASTER,
COUPLER
Module LED
Indicators
LNK/ACT, FDX/HDX, SPEED, RING PORT,
COUPLER PORT
Alarm Contact One relay output with current carrying capacity of
3A @ 30 VDC or 3A @ 240 VAC
Optical Fiber (100BaseFX)
Distance Multi-mode
0 to 5 km, 1300 nm (50/125μm, 800 MHz*km)
0 to 4 km, 1300 nm (62.5/125μm, 500 MHz*km)
Single-mode
0 to 40 km, 1310 nm (9/125μm, 3.5 PS/(nm*km))
Min. TX Output Multi-mode: -20 dBm; single-mode: -5 dbm
Max. TX Output Multi-mode: -10 dBm; single-mode: 0 dbm
RX Sensitivity Multi-mode: -32 dBm; single-mode: -34 dbm
Power
Input Voltage 24 VDC (18 to 36V)or 48 VDC (36 to 72V)or
110/220 VDC/VAC
(88 to 300 VDC and 85 to 264 VAC)
Input Current Max. 2.58A @ 24VDC
Max. 1.21A @ 48VDC
Max. 0.64/0.33A @ 110/220VDC
Max. 0.53/0.28A @ 110/220VAC
Physical Characteristics
Housing IP 30 protection, metal case
Dimensions
(W x H x D) 440 x 44 x 325 mm (17.32 x 1.73 x 12.76 in.)
Weight 5900 g
Installation 19” rack mounting
Regulatory Approvals
Safety EN60950-1 (Pending)
Power Automaton IEC61850-3, IEEE 1613
Road Traffic NEMA TS2
Rail Traffic EN50121-4 (Pending)
Maritime DNV (Pending), GL (Pending)
EMI FCC Part 15, CISPR (EN55022) class A
Environmental Limits
Operating Temp. -40 to 85°C (-40 to 185°F)
Cold start of min. 100 VAC at -40°C
Storage Temp. -40 to 85°C (-40 to 185°F)
Ambient Relative
Humidity. 5 to 95% (non-condensing)
Warranty 5 years
Copyright ©2008
Moxa Inc.
All rights reserved.
Reproduction without permission is prohibited.
Tel: [phone] www.moxa.com
Fax: [phone] [email protected]