moyno 2000 User manual

MOYNO®
2000 Pumps
G1 Flanged Models
SERVICE MANUAL

TABLE OF CONTENTS
Page
1-1. INTRODUCTION..................................................1
1-2. GENERAL....................................................1
1-3. NAMEPLATE DATA.....................................1
1-4. Pump Rotation ..................................1
1-5. Model Number...................................1
1-6. Frame Size Designation....................1
1-7. Type Designation..............................1
1-8. Trim Code .........................................2
1-9. Variation of Standard Parts...............2
2-1. INSTALLATION...................................................2
2-2. GENERAL....................................................2
2-3. PIPING.........................................................2
2-4. Suction Piping...................................2
2-5. Suction Housing Rotation..................2
2-6. Discharge Piping...............................2
2-7. FOUNDATION ...........................................3
2-8. SHAFT ALIGNMENT .................................3
2-9. On Coupling Connected Units...........3
2-10. On Belt Drive Units ...........................3
2-11.WATER FLUSH OF PACKING ..................3
3-1. OPERATION........................................................4
3-2. INITIAL CHECK...........................................4
3-3. START-UP...................................................4
3-4. PACKING LEAKAGE...................................4
4.1. MAINTENANCE .................................................4
4-2. GENERAL....................................................4
4-3. PACKING ADJUSTMENT............................4
4-4. PACKING REPLACEMENT.........................5
4-5. LUBRICATION.............................................5
4-6. Bearings............................................5
4-7. Gear Joints........................................5
4-8. DISASSEMBLY..........................................5
4-9. Disconnect Pump..............................5
4-10. Packing Removal..............................5
4-11. Stator Removal .................................5
4-12. Drive End Gear Joint Removal..........6
4-13.Rotor and Connecting Rod
Removal............................................6
4-14. Drive Shaft and Bearings Removal....6
4-15. CLEANING ................................................6
4-16. INSPECTION.............................................7
4-17. Bearings...................................7
4-18. Drive Shaft...............................7
Page
4-19. Seals.......................................................7
4-20. Packing...................................................7
4-21. Rotor.......................................................7
4-22. Stator......................................................7
4-23. All Other Parts........................................7
4-24. ASSEMBLY..........................................................
4-25. Lubrication During Assembly..................7
4-26. Packing Installation.................................8
4-27. Bearing Housing/Suction
Housing Assembly..................................8
4-28. Bearing/Drive Shaft Assembly................8
4-29. Rotor/Stator Assembly............................9
4-30. Rotor Gear Joint Assembly.....................9
4-31. Rotor/Stator to Drive End
Assembly..............................................10
4-32. Drive End Gear Joint Assembly............10
4-33. Stator Support/Discharge Assembly.....11
4-34. Final Assembly.....................................11
4-35. Packing Adjustment..............................11
4-36. STORAGE.......................................................11
4-37. Short Term Storage..............................11
4-38. Long Term Storage...............................11
4-39. PACKING SPECIFICATION............................12
4-40. VARIATIONS OF STANDARD PARTS...........12
4-41. Rotors...................................................12
4-42. Drive Shafts..........................................12
4-43. STANDARD HARDWARE...............................13
4-44. SELECTING THE CORRECT PART...............14
4-45. PARTS LIST....................................................15
4-46. SHAFT SLEEVE ARRANGEMENT.................24
4-47. Disassembly.........................................24
4-48. Assembly..............................................24
4-49. FIBER DEFLECTOR OPTION..............................
4-50. OPERATION..........................................26
4-51. DISASSEMBLY/ASSEMBLY..................26
4-52. PARTS LIST...........................................26
4-53. FLUSH GLAND OPTION..................................26
4-54. GENERAL..............................................26
4-55. INSTALLATION......................................26
4-56. OPERATION..........................................27
4-57. STANDARD HARDWARE......................28
4-58. PARTS LIST...........................................28
4-59. TROUBLESHOOTING CHART........................29
Note: This service manual outlines installation, operation and maintenance procedures
for the flanged “G1” models of the Moyno 2000 pump. For information on the open
throat (G2) and/or the bridge breaker (G3) models of the Moyno 2000 pump, refer
to the G2/G3 Service Manual, or contact your nearest Moyno pump representative.

SERVICE MANUAL
MOYNO®2000 PUMPS
G1 Flanged Models
1-1. INTRODUCTION
1-2. GENERAL
The Moyno® 2000 Pump is the culmination of over 70
years of experience in manufacturing and marketing fluids
handling equipment. This rugged pump has been engineered
to be the most reliable product ever sold under the Moyno
name. The pump has been painstakingly tested to assure
consistent performance in the most difficult of applications. It
represents the next generation of the world’s most versatile
pump.
The Moyno 2000 Pump is a progressing cavity pump. A
single helical rotor rolling eccentrically in the double helix
of the stator creates the pumping action. The rotor in
conjunction with the stator forms a series of sealed cavities
180 degrees apart. As the rotor turns, the cavities progress
from the suction to the discharge. As one cavity diminishes,
the opposing cavity increases at exactly the same rate. Thus
the sum of the two discharges is a constant volume. The
result is a pulsation-free positive displacement flow utilizing
no valves.
1-3. NAMEPLATE DATA
The pump nameplate, located on the bearing housing,
contains important information relating to the operation and
servicing of the pump. This information includes the direction
of rotation arrow and the pump model and serial numbers
(see fig. 1-1). The pump model number must be used for
reference when ordering spare parts.
1-4. Pump Rotation. A rotation arrow on the nameplate
indicates the direction of rotation. Normal rotation of Moyno
2000 pumps is clockwise, when viewed from the driven end
of the pump.
1-5. Model Number. The pump model number consists of
three component parts: Frame Designation, Type
Designation and a Trim Code. A typical model number for
example, might be 1G065G1 CDQ AAA, as shown on the
nameplate in fig. 1-1.
1-6. Frame Designation. The Moyno 2000 is modular
in concept allowing for optimal matching of drive ends and
pump elements (rotor and stator) to meet the requirements
of the application. The seven or more characters in the frame
Figure 1-1. Typical nameplate showing rotation arrow,
model and manufacturing serial numbers.
designation describe the particular combination of drive end and
pump elements, as well as other construction details of your
pump.
The first character in the frame designation, always a number,
indicates the number of stages of the pumping elements.
The second character is always a letter (E through K) and
indicates the drive end size.
The third, fourth and fifth characters are numbers indicating
the theoretical capability of the pumping elements per 100
revolutions on water. Sometimes the fifth letter is followed by the
letter “E”, which denotes that the pumping element is our Ultra
Pro 23 geometry.
The sixth character represents the type of universal joint
utilized. The letter G indicates a gear type joint. Other
configurations maybe indicated by the letters P or F.
The seventh character, a number, indicates the type of suction
housing. Flanged suction port pumps are designated by the
numeral “1,” open throat pumps by the numeral “2” and open
throat pumps with a bridge breaker option by the numeral “3.”
1-7. Type Designation. Following the Frame Designation is
the Type Designation, a series of three letters describing the
materials from which the pump is constructed.
Section:
MOYNO®2000 PUMPS
Page: 1
Date: June 2002

Page 2
The first letter identifies the material of the suction
housing.
C — Cast Iron
E — Carpenter 20 Stainless Steel*
H — Hastelloy “C” **
M — Monel***
S — 316 Stainless Steel
W — Cast Steel
X — Special to application
Note: The bearing housing of the pump is always made of
cast iron.
The second letter indicates the material used in the drive
shaft, connecting rod, rotor and other wettable parts.
D — Alloy Steel
E — Carpenter 20 Stainless Steel*
G — 416 Stainless Steel
H — Hastelloy “C” **
J — 17-4 PH Stainless Steel
M — Monel***
S — 316 Stainless Steel
X — Special to application
The third letter indicates the material of the stator. It
identifies only the stator material and not that of the tube in
which the stator is placed, which is always carbon steel.
Standard stator materials used in the Moyno 2000 pump are
as follows:
B — EPDM 300, 70 Durometer
C — Nitrile 103, 50 Durometer
D — Tool Steel
E — Nitrile 110, 70 Durometer
F — Fluoroelastomer 500, 75 Durometer
G — 416 Stainless Steel
H — Hastelloy “C” **
J — 17-4 PH Stainless Steel
K — Hypalon 800, 70 Durometer †
M — Nitrile 100M 70 Durometer
P — Thiokol 70 Durometer ‡
Q — Nitrile 100, 70 Durometer
R — Natural Rubber 200, 55 Durometer
I — Teflon 15% glass †
U — Urethane 70 Durometer
X — Special to application
Z — White Nitrile 150, 70 Durometer
A typical type designation such as CDQ, would identify the
following materials of construction:
C = Cast iron suction housing
D = Alloy steel rotor, drive shaft, connecting rod
and other minor metallic parts in contact
with the fluid being pumped.
Q = Nitrile (70 durometer) stator
* Carpenter 20 is a trademark of Carpenter Technology
Corp.
** Hastelloy is a trademark of Cabot Corp.
*** Monel is a trademark of INCO Alloy Corp.
†Hypalon and Teflon are trademarks of E.I. DuPont de
Nemours and Company
‡Thiokol is a trademark of Morton Thiokol Inc.
1-8. Trim Code. Also included in the Model Number is the
three character Trim Code which is used to identify pump
construction. The letters “AAA” signify standard construction,
with letters other than “A” signifying variations. The first letter
identifies sealing variations; the second, internal variations;
and the third, rotor variations.
1-9. Variations of Standard Parts. Refer to Sections 4-40
through 4-42 for variations available for modifying pumps to
meet specialized pumping conditions. If the trim code of your
pump is other than “AAA,” contact your nearest Moyno
representative for clarification. Do not modify your pump with
any variation unless you have determined that it is
compatible with your application.
2-1. INSTALLATION
2-2. GENERAL
Moyno pumps are lubricated and tested at the factory prior
to shipment and require minimum pre-start up maintenance.
Packing, however, is not lubricated at the factory.
Accessibility to the pump and adequate clearance should
be a prime consideration in any installation. Enough space
should surround the unit so that maintenance can be carried
out with ease.
2-3. PIPING
2-4. Suction piping should be as short as possible. Nor-
mally, the suction line should be the same size as the pump
suction; however, conditions, such as high viscosity or flow
velocities, may dictate otherwise. Long-sweep 90-degree
elbows or 45-degree elbows should be used instead of
standard elbows. Piping configurations, which trap air,
should be avoided.
2-5. Suction housing rotation to any position 360° about
the centerline of the pump is possible. To rotate, loosen the
hex head bolts holding the clamp ring to the bearing housing.
Remove the packing gland halves and the packing studs.
Loosen the stator support cap and rotate the suction
housing, stator and discharge flange together. Replace the
packing gland studs in the threaded hole provided.
CAUTION: Rotating the suction flange by any other
method may tear the stator gaskets causing
a leak. Once the gaskets have been com-
pressed, it is virtually impossible to rotate
any one of the two compressing surfaces
without tearing the gasket.
2-6. Discharge piping diameter should generally be as
large as the pump ports unless fluid conditions indicate
otherwise.
An easily removable section of piping one-to-two times
longer than the connecting rod should be mated to the
discharge port. This will allow the stator to be removed
without having to disassemble the complete pump.

2-7. FOUNDATION
Each unit should be mounted on a strong, fabricated-steel
base plate. The base plate should be mounted on a concrete
foundation. The foundation should be approximately 4” to 8”
longer and wider than the base for which it is built. (See fig.
2-1.) Anchor bolts for the base plate should be located in the
foundation.
Figure 2-1. Typical Foundation Example
Check the base plate surface with a carpenter’s level and
place shims under the base plate at the places necessary to
make it level. Then check the pump, driver shaft and the
pump ports to ensure that they are level. Complete base
mounted units supplied by Moyno including pump and driver
are leveled with respect to the base at the factory. Shifting
may occur during shipment. The pump and driver should be
realigned. Care should be exercised to ensure that all
components are level and mounted in a direct line.
For maximum rigidity and lower noise levels the base
plate should be grouted to the foundation after the anchor
bolts have been evenly tightened. A good grade of non-
shrink grout is recommended. The spaces between the base
plate and the foundation around the shims should also be
filled with grout. Allow the grout to dry according to
manufacturer’s instructions, then fully tighten the anchor
bolts.
2-8. SHAFT ALIGNMENT
Although the base-mounted units supplied by Moyno are
leveled with respect to the base before shipment, most of the
larger pump and driver units are shipped with the flexible
coupling disconnected.
After the base has been bolted down to the foundation,
check the following conditions:
2-9. On coupling connected units, be sure that the pump
and driver shafts are realigned before the coupling is con-
nected. Care should be exercised to ensure that all com-
ponents are level and mounted in a direct line.
Page 3
Check gap between coupling halves (refer to coupling
manufacturers recommendations). Adjustment can usually
be accomplished by loosening the mounting bolts on either
the pump or driver and moving the loosened component into
alignment with the fixed component. On couplings with equal
diameter hubs, it may be possible to lay a straight edge
axially across the coupling halves to check alignment.
2-10. On belt drive units, check to ensure that sheaves or
sprockets are in alignment. Check belts for proper tension.
Tension requirements will vary with type of belt, center
distances, and belt speeds. Consult belt manufacturer for
specific recommendation.
2-11. WATER FLUSH OF PACKING
The packing may be either grease lubricated through a
grease fitting in the stuffing box or have plumbing connected
to the housing to allow for water flushing.
Packing is not grease lubricated at the factory prior to
shipping.
When the material being pumped is abrasive, water
flushing the packing is recommended to extend shaft life.
Clean water can be injected though a 1/8” NPT hole that
normally houses the grease fitting for lubricating the packing.
The water should be permitted to leak axially along the shaft
and be removed from the second tapped hole in the stuffing
box. The discharge from the stuffing box should be throttled
slightly to maintain 10-15 PSI higher pressure in the stuffing
box than is present in the suction housing. (See fig. 2-2.)
Flow rate should be approximately 1/2-2 gpm.
If a mechanical seal is used, consult the seal manufac-
turers’ instructions for seal flush requirements.
Figure 2-2. Typical water flush arrangement for units
with packing includes strainer valve (1), pressure
regulating valve (2), sight flow meter (3), solenoid
valve (4), pressure gauge (5), and needle valve (6).

Page 4
3-1. OPERATION
3-2. INITIAL CHECK
Before putting the pump into operation, the following
items should be checked to ensure that each piece of
equipment is installed correctly:
— Pump, driver, coupling or sheave alignment.
— Electrical connections.
— Gauges and other instruments.
— Water flush connection to the stuffing box.
— Pump rotation. Normal rotation is indicated on the
nameplate on the bearing housing.
— All valves should be open on both suction and dis-
charge sides of pump.
CAUTION: This is a positive displacement pump. Do not
operate it against a closed valve.
3-3. START-UP
CAUTION: DRY OPERATION IS HARMFUL TO THE
PUMP! Never allow the pump to operate with-
out liquid, as dry operation will cause prema-
ture wear of the stator and possible damage.
The stator is lubricated by the liquid, which
is pumped.
1. Before operating the pump for the first time, fill it with
liquid (the drain plug hole on the suction housing may be
used for filling). If the liquid to be pumped is highly viscous,
dilute it before filling the pump. The liquid fill-up will lubricate
the stator for the initial start-up.
2. Once the pump has been filled with liquid, check for
direction of pump rotation by momentarily starting and
stopping the drive. Check rotation arrow on pump nameplate
for correct rotation.
3. In suction lift applications, when water flush is not
utilized it may be necessary to replace the zerk fittings at the
stuffing box (in suction housing) with pipe plugs to prevent
loss of prime due to air leakage.
4. If applicable, turn on the water to the packing.
5. Start pump.
3-4. PACKING LEAKAGE
A packed stuffing box is designed to control leakage, not
stop it completely. Leakage is generally necessary to reduce
friction and dissipate heat. The amount of leakage necessary
will depend on the fluid pumped, the installation, and
pump.speed and type. Refer to Section 4-3 for packing
adjustment.
Moyno 2000 pumps have been designed for minimum
stuffing box leakage when properly maintained. If leakage
cannot be tolerated, then a mechanical seal should be used.
4-1. MAINTENANCE
Note: In this section, the first reference to each pump part
will be followed by a number or a letter in parentheses
( ). These numbers and letters are those used to
identify the pump parts and hardware items in the
fold-out Exploded View (Figure 4-8).
4-2. GENERAL
The Moyno 2000 pump has been designed for a minimum
of maintenance, the extent of which is routine adjustment
and lubrication of packing. The pump is one of the easiest
to work on, in that the main elements are very accessible
and require few tools to disassemble.
4-3. PACKING ADJUSTMENT
Packing gland nuts should be evenly adjusted so they are
little more than finger tight. (See fig. 4-1.) Over-tightening the
packing gland may result in premature packing failure and
possible damage to the shaft and gland.
When packing is new, frequent minor adjustments during
the first few hours of operation are recommended in order to
compress and seat each ring of packing evenly.
1. Upon initial start-up of the pump, adjust the gland nuts
for a leakage rate of 1-2 drops per second until the packing
has seated and adjusted to the operating temperature
(approximately 10-15 minutes).
2. If leakage is excessive after 15 minutes of operation,
tighten the gland nuts until a desired leakage rate is ob-
tained.
CAUTION: Do not tighten until zero leakage is obtained.
Over-tightening of the packing gland may
result in accelerated wear on the packing and
damage to the shaft. In those situations
where no packing leakage can be tolerated,
consult your Moyno Authorized Service
Representative.
Figure 4-1. Cross Section of Stuffing Box

4-4. PACKING REPLACEMENT
When leakage can no longer be regulated by tightening
the gland nuts, remove and replace the packing. Replace as
follows:
1. Remove packing gland nuts (F), and slide gland (21)
and slinger ring (20) back along drive shaft (14).
2. Remove packing gland studs.
3. Use a pair of packing extractors (Figure 4-2) to remove
four packing rings (22), lantern ring halves (23) and two
additional packing rings (22).
Figure 4-2. Packing Removal Tool
3. Inspect surface of drive shaft for wear or grooves. If
shaft is worn through the chrome plating into the base metal,
or is badly scored or grooved it should be replaced.
4. If drive shaft is not worn, install two rings of packing, the
lantern ring halves, and four more rings of packing; lubrica-
ting them before installation with a good grade of packing
grease. Be sure to stagger the packing ring joints at 90°
increments. (See Section 4-26.)
CAUTION: Always use a proper packing tamper tool to
install packing. Do not use a pointed or sharp
tool, as damage to the packing material or
drive shaft could result. To assure proper
shaft lubrication, never use a one-piece
spiral wrap packing.
5. Replace packing gland (21) and secure with packing
gland nuts. (See fig. 4-1.)
6. Adjust packing per Section 4-3.
4-5. LUBRICATION
4-6. Bearings. The bearings are lubricated at the factory
and will only need to be re-lubricated when the shaft/bearing
assembly is removed from the pump.
4-7. Gear Joints. Both gear joints are packed with lubri-
cant during assembly, and will only need to be re-lubricated
when gear joints are disassembled.
4-8. DISASSEMBLY
Note: The following instructions cover ONE procedure for
disassembling all pump components. Major pump
components can be disassembled in various ways
since specific installation location limitations will
determine method of component removal.
4-9. Disconnect Pump
1. Flush the pump (preferably with clean water) to remove
the pumpage from the unit.
Page 5
2. Shut off pump.
3. Close suction and discharge valves.
4. Turn off flush water to packing or mechanical seal,
if used.
5. Disconnect power source.
6. Drain any fluid in pump by removing the drain plug or
inspection plate.
7. Remove inspection plate (32) and gasket (33).
4-10. Packing Removal
1. Shut off pump.
2. Complete Section 4-9, steps 3 - 6.
3. Remove gland adjustment nuts (F), gland studs (H) and
gland halves (21) from stuffing box.
4. Remove packing rings (22). This is best done by using
flexible packing extractors (see fig. 4-2). Use two extractors
simultaneously on opposite sides of each ring. Pull evenly.
5. Remove lantern rings (23) in similar fashion. Twist split
rings to remove from shaft.
6. Remove additional packing rings.
4-11. Stator Removal
1.Complete Section 4-9.
2. Remove section of discharge pipe attached to dis-
charge flange (37).
3. Remove top half of stator support (31).
4.Unbolt stator clamp ring (36A) from suction housing (29).
Pull stator off rotor (see note below). Remove stator
gasket (34). Use a screwdriver tip to carefully remove
stator retaining ring (35). (See fig. 4-3.) Remove stator
clamp ring (36) from stator (30).
Figure 4.3. Typical Retaining Ring Removal

Page 6
NOTE: On multiple stage pumps, or when cleaning,
checking or changing stator (30), rotor (40), and/or gear joint
assembly, one of the following procedures is suggested for
removing the stator.
Method 1: Utilize Moyno’s Hydraulic Stator Removal Device
(SRD). See separate SRD service manual or contact the
local Moyno distributor for further information on this new
product.
Method 2: Use winch-type device anchored directly opposite
stator end. Attach cable to discharge flange (37) to pull
stator (30) off rotor (40).
Method 3: Remove stator (30), rotor (40) and connecting
rod (38) as a single unit (See Section 4-13). Place the stator
(30) in an upright position on the discharge flange (37).
Remove rotor (40) and connecting rod (38) from the stator
(30). It may be necessary to use a chain or sling with a
lifting device. Anchor discharge flange (37) securely to the
floor before lifting.
Method 4: Hold stator (30) with pipe or strap wrench and
turn drive shaft had (4) clockwise to unscrew stator (30) from
rotor (40).
5. Remove discharge flange by unbolting from stator
clamp ring (36B) and remove stator gasket (34).
Remove stator retaining ring (35) and stator clamp ring
from stator (30).
6. Check rotor (40) and stator (30) for wear. See Sections
(4-21) and (4-22) for instructions.
4-12. Drive End Gear Joint Removal
1. Complete Section 4-9.
2. Remove drive coupling or V-belts and pulley from drive
shaft head (4).
3. Remove vent plugs (C) from drive shaft head (4) and
drive shaft (14). Remove set screw (D) from drive shaft (14).
Remove six socket head screws (E) from drive shaft head
(4) and remove drive shaft head. Remove primary thrust
plate (6) from drive shaft head and remove two keys (7).
4. Remove lock nut (9) from end of connecting rod (38).
Remove ring gear (8), gear ball (10), secondary thrust plate
(11), seal support (12), and gear joint seal (13).
Note: It is recommended that each time the drive end gear
joint is disassembled, the drive shaft O-ring (5) and
gear joint seal (13) should be replaced.
4-13. Rotor and Connecting Rod Removal
1. Complete Sections 4-9, 4-11 and 4-12.
2. Pull the rotor/connecting rod assembly from the pump.
Remove the vent plug (C) and set screw (S) from the gear
joint shell (39).
3. Remove six socket head screws (T) from head ring (42)
and remove head ring and O-ring (41). Slide connecting rod/
gear joint assembly off rotor head. Remove gear joint keys
(7) and primary thrust plate (6) from rotor (40).
4. Slide gear joint shell (39) off gear ball/connecting rod
assembly. Slide ring gear (8) off gear baIl (10).
5. Clamp connecting rod (38) in vice or hold with pipe
wrench and remove lock nut (9). Remove gear ball (10), sec-
ondary thrust plate (11), seal support (12), and gear joint
seal (13) from connecting rod.
Note: It is recommended that each time the rotor end gear
joint is disassembled, the rotor head O-ring (41) and
gear joint seal (13) should be replaced.
4-14. Drive Shaft and Bearings Removal
Note: If the space immediately in front of the pump is unob-
structed for a distance equal to the length of the drive
shaft, follow steps 1 through 3.
1. Complete Sections 4-9 and 4-12.
2. Remove six hex head screws (A) from bearing cover
plate (2). Slide bearing cover plate (2) with radial grease seal
(1) and O-ring (3) off drive shaft.
3. Pull drive shaft/bearing assembly out of bearing
housing, taking steps to support the weight of the assembly
as the bearings clear the housing. Remove grease seal (19)
from the bearing housing.
Note: If the space in front of the pump is obstructed, and the
obstruction is not easily moveable, follow steps 4
through 6.
4. Complete Sections 4-10 and 4-11, and pull the rotor/
connecting rod assembly from the pump.
5. Remove the four cap screws (0) from the clamp ring
(28), and the four cap screws fastening the bearing Housing
(26) to the base. Slide the bearing housing/shaft assembly
out of the suction housing until the quill clears the stuffing
box. Assembly may now be turned or removed to an area
where sufficient space is available to permit removal of the
shaft/bearing assembly.
Note: Some pumps have a sleeve installed on the drive
shaft to receive any possible wear caused by the
packings. (See fig. 4-10.) To remove sleeve, refer to
Section 4-47.
CAUTION: The bearings are pressed on the shaft during
assembly. Care must be taken during
disassembly to avoid damaging the bearings
or shaft.
6. Remove bearing lock screw (17) from bearing nut (18).
Using suitable spanner wrench or soft punch and hammer,
thread lock nut off drive shaft. Do not use a pipe wrench to
remove the lock nut.
7. Remove both halves of bearing spacer (16) from shaft,
and using suitable bearing press and adapters, press bear-
ings off shaft.
4-15. CLEANING
Clean all parts in a suitable cleaning solvent being careful
to observe all safety precautions regarding the use of
solvent.

4-16. INSPECTION
4-17. Bearings. After cleaning, rotate bearings very slowly
under hand pressure to feel for smoothness and even action.
Never spin a dry bearing. Check for cracks, galling, pitting,
burrs, etc. Replace bearing if there is any doubt concerning
complete serviceability.
4-18. Drive Shaft. Inspect drive shaft (14) for scoring, burrs,
cracks, etc. Replace as necessary.
4-19. Seals. It is sound practice to always replace grease
seals (1 and 19) whenever drive shaft and tapered roller
bearings are removed. Apply Locktite 690 to outside
diameter of both grease seals.
4-20. Packing. It is sound practice to always replace pack-
ing (22) whenever the pump bearing housing is
disassembled.
4.21. Rotor.
1. To check for excessive wear of rotor (40), measure the
rotor crest-to-crest diameter (see fig. 4-4) and compare with
the following chart:
Rotor
Capacity Standard *Crest to Crest Dia. (inches)
008 2.772 + .000/—.004
012 2.676 + .000/—.004
022 3.425 + .000/—.004
036 4.015 + .000/—.004
050 4.015 + .000/—.004
065 4.906 + .000/—.004
090 4.906 + .000/—004
115 5.709 + .000/—.004
175 6.584 + .000/—.004
335 5.800 + .000/—.005
345 7.260 + .000/—.004
620 7.128 + .000/—.005
800 7.658 + .000/— .004
* These dimensions are applicable for AAA trim codes only.
Note: The rotor is designated by the third, fourth and fifth
numbers in the Model Number, i.e., 1G065G1.
2. If the measured crest to crest diameter is within 0.010
inch of the standard value and is free of deep nicks, gouges,
or other surface defects, the rotor is re-usable.
3. Rotors with crest to crest values 0.011 to 0.050 inch
under the standard values should be replaced. These rotors
can be renewed by chrome plating to standard dimensions
provided that:
a.The key slots are not excessively worn.
b.The rotor surface is not cracked, pitted or deeply
grooved (1/32 inch or more).
c.The base surface metal is not pitted or corroded.
4. Rotors may be sent to Moyno or any other competent
plating shop. Rotors should be stripped and replated to
standard dimensions, then buffed.
4-22. Stator. A worn stator may appear pitted and gouged,
or may appear smooth similar to when new. Performance is
the best measure of rotor to stator fit. If unable to measure
performance adequately, suspected stator wear can be
evaluated by a Moyno sales or factory representative.
4-23. All Other Parts. Check for cracks, excessive wear,
damage to threaded holes, burrs, etc. Replace as necessary.
Replace O-rings and all gaskets at each disassembly and
reassembly.
4-24. ASSEMBLY
The Moyno 2000 pumps are reassembled in the reverse
order of dismantling. The following suggestions are offered:
1. While pump is dismantled, check all gaskets, seals,
packing, and O-rings. Replace all worn items. It is recom-
mended that the gear joint seals (13), gear joint O-ring (41),
and drive shaft O-ring (5) be replaced each time either of the
gear joints is disassembled.
2. During the assembly process, cleanliness is important.
To avoid premature failure, bearings and gear joint compo-
nents must be handled with care and kept clean.
4-25. Lubrication During Assembly
Note: The bearings are lubricated at the factory, and will
only need to be re-lubricated when the shaft/bearing
assembly is completely removed from pump.
1. Bearings. Pack bearings after installation on shaft
(Section 4-28). Lubricant should be packed around all of the
rollers and should completely cover the faces of the races.
The void inside the spacer between the bearings should be
filled approximately half way with lubricant.
2. Gear Joints. Both gear joints should be packed with
lubricant during assembly (Sections 4-30 and 4-32). DO
NOT use zerk fittings to lubricate gear joints after assembly.
The pipe plugs (C) in the drive shaft head, drive shaft, and
gear joint shell are vent plugs and MUST BE REMOVED
during assembly of the gear joints to allow excess lubricant
to vent from the gear joints.
3. Packing. Lubricate packing rings during assembly. Ad-
ditional grease can be added after assembly through the
zerk fittings installed in the side of the stuffing box.
Page 7
Figure 4-4. Measuring Rotor Dimension

Page 8
4. Approved lubricants:
CAUTION: Do not mix different brands of lubricants for
the same application.
Area to Lubricate Approved Lubricant or Equivalent
Bearings, Gear Joints
& Packing ACG-2 (Dubois Chemical, Inc.)
4-26. Packing Installation
1. The standard packing set (22) consists of six braided
packing rings. Lantern ring halves (23) must be ordered
separately.
2. Install packing and lantern ring halves into the stuffing
box area of the suction housing (29) in the following
sequence:
a. Wipe a film of lubricant on each packing ring and
install two rings. Push each ring firmly in place.
Note: Install the packing rings with the splits staggered at
90 degrees to the adjacent ring of packing. On initial
assembly, one ring of packing may not fit in stuffing
box. This final ring of packing should be installed
after pump is started and packing is seated.
CAUTION: Always use a proper packing tamper tool to
install packing. Do not use a pointed or sharp
tool, as damage to the packing material or
drive shaft could result. To assure proper
shaft lubrication, never use a one-piece spiral
wrap packing.
b. Install the two lantern ring halves with the flat side
against the packing.
c. Install final four packing rings, firmly pushing each
ring into place.
3. Install packing gland studs (H), packing gland halves
(21), and gland adjusting nuts (F). Tighten nuts finger tight at
this time.
4-27. Bearing Housing/Suction Housing Assembly. This
procedure may be performed now or after the bearing/drive
shaft assembly is installed in the bearing housing.
1. Place clamp ring (28) on suction housing (29) and
install retaining ring (27) in groove on suction housing.
2. Slide turned diameter of suction housing into bore on
end of bearing housing (26). Align holes in clamp ring (28)
with four threaded holes in bearing housing (26) and thread
four hex head screws (0) with lock washers into threaded
holes. Tighten finger tight.
3. Rotate suction flange to desired position (if not already
fastened to piping) and tighten four hex head screws (0).
Note: Refer to Torque Guidelines Chart (page 12) for the
proper torque requirement for all threaded fasteners.
4-28. Bearing/Drive Shaft Assembly
1. Bearings must be pressed on the shaft in the following
sequence: [Larger units (G drive end and larger) require
heating of the bearings to 250° F before assembly.]
a. Press bearing cone on shaft (14), making sure
rollers face in proper direction to receive cup (step b). Cone
should be pressed firmly against shoulder on shaft.
b. Place cup on rollers.
c. Place bearing spacer (16) halves on cup.
d. Place second cup on spacers.
e. Press second bearing cone on shaft with rollers fac-
ing seat in cup. Cone should be pressed on until face of
cone is flush or even with shoulder on shaft.
CAUTION: Do not press second cone past shoulder on
shaft.
2. Thread bearing nut (18) on shaft (14) and tighten until it
rests against the shoulder on the drive shaft. Install brass tip
set screw (17) in bearing nut and tighten.
Note: The tapered bearings are designed such that when
properly installed there may be a very slight end play in
the bearings (bearing spacer halves may slip freely out
of place) or they may have a slight pre-load (bearing
spacer halves held tightly in place and bearings do not
turn freely).
3. Remove bearing spacer halves (16). Thoroughly pack
lubricant around rollers and on bearing races. Install one
half of bearing spacer. Fill area between bearings half full of
lubricant, and install other half of bearing spacer.
Note: Assuming the bearings are not too hot, an alternate
method of lubricating bearings is as follows: Pack the
rollers of the first cone immediately after it is pressed
on shaft. Lubricate race of first cup before it is
installed. Place bearing spacer halves in place and fill
it full of lubricant. Lubricate race of second bearing
cup and place on spacer. Pack rollers of second cone
with lubricant, and press on shaft until flush with
shoulder.
Note: If too much grease is packed into the bearings during
assembly, it may seep from the grease seals during
the first few hours of operation until the proper lubri-
cant level is achieved. This lubricant should be wiped
from the seal area, when the pump is not operating,
to prevent contaminants from collecting in the seal
area.
4. Install (light press) grease lip seals (1 and 19) into
bearing cover plate (2) and bearing housing (26) with
Locktite. The lip of the radial grease seal (1) should be facing
outward with spring visible. The lip of the seal (19) should be
facing the bearings. The lips of both seals should be wiped
with grease.
5. Install drive shaft with bearings in bearing housing,
being careful to avoid damaging the grease seal (19).

6. Place O-ring (3) on bearing cover plate and bolt
bearing cover plate to bearing housing using six hex
head screws (A) and lock washers. The six screws
should be tightened evenly, and care should be taken to
insure the O-ring becomes seated in the step in the
bearing housing. When the bearing cover plate is fully
secured to the bearing housing, a small gap of 0.010 to
0.020 inch will exist between the bearing cover plate
and the bearing housing.
Note: Some pumps have a sleeve installed on the
drive shaft to receive any possible wear caused
by the packing. (See fig. 4-10.) If the sleeve is
used, install at this time. Refer to Section 4-48
for details.
4-29. Rotor/Stator Assembly
1. Slide head ring (42) over rotor (40) contour to the
rotor head. The side of the head ring with the smallest
diameter holes should be facing the rotor head.
Note: On some models the head ring is a two-piece
component which eliminates this step.
2. Slide stator clamp rings (36) on both ends of the
stator (30) and secure in position with retaining rings
(35).
3. On F012, G022, H036, H050 and K115 models,
place one stator gasket (34) in recess of adapter flange
(25A), and fit adapter flange with gasket to end of stator.
4. Coat the rotor (40) contour with waterless hand
cleaner, glycol or other lubricant compatible with the
stator elastomer. Insert rotor into stator so that rotor
head is at the specified distance from the end of the
stator (Dimension “A,” fig. 4-5). On F012, G022, H036,
and K115 models, be sure the rotor is inserted in the
end of the stator fitted with the adapter flange (25A) and
gasket (34).
Note: Rotor can also be inserted in the stator utilizing
Moyno’s Hydraulic Stator Removal Device
(SRD). See separate SRD service manual or
contact the local Moyno distributor for further
information on this new product.
Note: Turning the rotor counterclockwise while
inserting into stator will ease assembly.
4-30. Rotor Gear Joint Assembly
1. Slip O-ring (41) over the rotor head and allow to
hang loose with head ring. Insert primary thrust plate (6)
into rotor head, flat side first. Thrust plate and rotor head
surfaces must be flush to assure proper assembly and
operation of the pump. (See fig. 4-6.)
2. Assemble the rotor end gear joint by first fitting a
gear joint seal (13) onto the connecting rod assembly
(38). The seal must be positioned so that the flat face of
the seal neck fits into the seal retainer component of the
connecting rod assembly. Apply a small coating of
approved gear joint lubricant to the inside surfaces of
the seal.
Page 9
3. Apply a small amount of lubricant to the flat face of
the seal support (12) and slide it onto the connecting rod
so that the flat face and radius of the support is against
the seal.
4. Grease the concave spherical surface of the rear
thrust plate (11) and position thrust plate against the
seal (13) with the lip on the outside diameter of the seal
fitting the step on the back side of the thrust plate.
Frame
Designation A
(inches)
1E008G1 4.06
2E008G1 4.06
4E008G1 4.06
6E008G1 4.06
1E012G1, 1E018EG1 4.06
2E012G1, 2E018EG1 4.06
4E012G1 4.06
1E022G1, 1E033EG1 3.62
2E022G1, 2E033EG1 3.62
1E036G1 4.56
1F022G1 4.62
2F022G1 4.62
4F022G1 4.62
6F01231 5.00
1F036G1,1F0543G1 4.00
2F036G1, 2F054EG1 4.00
1F050G1, 1F075EG1 4.00
2F050G1, 2F075EG1 4.00
4F050G1 4.00
1F065G1 4.75
1G036G1 5.68
2G036G1 5.68
4G036G1 5.68
4G050G1 5.68
6G050G1 5.68
6G022G1 6.06
1G065G1, 1G098EG1 6.06
2G065G1, 2G098EG1 6.06
1G090G1 6.06
2G090G1 6.06
1G115G1 6.19
Frame
Designation
A
(inches)
1H065G1 6.25
2H065G1 6.25
4H065G1 6.25
2H090G1 6.25
4H090G1 6.25
6H036G1 6.62
6H050G1 6.62
1H115G1 6.25
2H115G1 6.25
1H175G1 6.75
1J115G1 6.84
2J115G1 6.84
4J115G1 6.84
6J065G1 6.84
6J090G1 6.84
1J175G1 7.00
2J175G1 7.00
1J335G1 7.19
1K175G1 8.70
2K175G1 8.70
4K175G1 8.70
6K115G1 9.20
1K335G1 8.70
2K335G1 8.70
3K335G1 8.75
1K345G1 8.75
2K345G1 8.75
3K345G1 8.75
1K620G1 8.75
2K620G1 8.75
1K800G1 7.50
2K800G1 7.50
Fig. 4-5. Rotor Installation

Page 10
5. Apply a film of grease to the splines on the inside of the
gear balI (10). Install gear ball on connecting rod (38), with
counter-bored end (end without splines) first on connecting
rod. Gear ball should slide freely against shoulder on
connecting rod. Place lock nut (9) on connecting rod and
tighten against gear ball. Apply grease to spherical surfaces
and teeth of gear ball.
6. Apply grease to the teeth of the ring gear (8), and slide
ring gear onto the gear ball. When ring gear is in place,
keyways should be facing the lock nut end of connecting rod.
7. Apply a thin coating of grease to the spherical surface
of the thrust plate (6) already installed in the rotor head. Fill
the recessed area in the rotor head with grease.
8. Slide the gear joint shell (39) over the connecting rod
and assembled gear joint components, being careful to seat
the outside diameter of the gear joint seal (13) in the end of
the gear joint shell (39). The two tapped holes in the gear
joint shell should be in line with one of the keyways in the
ring gear.
9. Place keys (7) in the keyways in the ring gear. Check to
insure the tapped holes in the side of the gear joint shell are
aligned with one of the keyways.
10. Align the keys in the ring gear with the keyways in the
rotor head. Slide assembled gear joint shell onto the rotor
head, checking to be sure the keys are properly engaged in
the rotor head and ring gear. The shallow hole in the rotor
head should be aligned with the first threaded hole in the
outside of the gear joint shell. Thread the setscrew (S) into
the threaded hole in the shell until light contact is made with
the hole in the rotor head.
11. Place O-ring (41) into step in gear joint shell. Align
holes in head ring (42) with six threaded holes in end of gear
joint shell and install stainless socket head screws (T).
Tighten the six socket head screws evenly, checking to in-
sure O-ring (41) remains in place. When tightened properly,
a small gap of a few thousandths of an inch may exist be-
tween the shell (39) and head ring (42).
12. Excess grease in the assembly will be purged from the
vent hole while the socket head screws are tightened.
Tighten the setscrew (S) in the shell. Move the free end of
the connecting rod in a circular motion to assure that the joint
is free and assembled properly. This will also help to purge
excess grease from the assembly.
13. Install the stainless steel pipe plug (C) in the
second hole in the shell and tighten.
4-31. Rotor/Stator to Drive End Assembly
1. If not already in place, slip stator clamp rings (36) on
both ends of stator (30), and install retaining rings (35) in
grooves provided on both ends of stator.
2. Place stator gasket (34) in recess in end of suction
housing:
a. On J335 model, stator gasket (34) will be installed
in recess in adapter housing (25B).
b.On F012, G022, H036, and K115 models, stator
gasket (34) will fit recess in adapter flange (25A) and adapter
flange gasket (24A) will fit recess in suction housing.
3. Move the rotor/stator/connecting rod assembly in po-
sition, and insert connecting rod through the suction housing
and drive shaft. Align stator with bore in suction housing, and
slide stator in place, checking to insure that stator gasket
(34) remains properly positioned.
4. Check the dimension “C” between the end of the con-
necting rod and face of the drive shaft as shown in fig. 4-7.
For proper assembly of the drive end gear joint, this
dimension should be no less than that shown in column C,
and should not exceed the amount in column C by more than
1/8 inch. Reposition rotor/stator assembly in or out of suction
housing as required to achieve the proper dimension.
Figure 4-6. Rotor Thrust Plate Seating Detail
Figure 4-7. Gear Joint Installation

5. If the stator is firmly seated against stator gasket in
suction housing recess, and connecting rod extends beyond
face of drive shaft by specified amount, stator may be se-
cured to suction housing. If the specified dimension cannot
be maintained with stator firmly seated, do not perform the
following step 6 until the drive end gear joint is properly
assembled.
6. Align holes in clamp ring (36A) with threaded holes in
suction housing, and thread four hex head screws (R) with
lockwashers through holes in clamp ring into threaded holes
in suction housing. Tighten hex head screws evenly.
4-32. Drive End Gear Joint Assembly
1. Check to see that connecting rod extends beyond face
of drive shaft by amount specified in column C of fig. 4-7.
(See Section 4-31, step 4.)
2. Fit the gear joint seal (13) on the connecting rod (38).
Push the seal firmly in place on the connecting rod so that
the neck on the seal seats in the recess in the seal retainer
component of the connecting rod.
3. Apply a film of gear joint grease to the inside of the gear
joint seal and to the flat face of the seal support (12). Slide
the seal support (12) onto the connecting rod such that the
flat face fits against the seal.
4. Apply a film of grease to the concave spherical surface
of the secondary thrust plate (11), and slowly push the thrust
plate into the drive shaft until it rests firmly against the seal.
5. Apply a film of grease to the gear balI (10) splines and
spherical surfaces, and install gear ball on connecting rod,
counter-bored end first (end without splines). Gear ball
should slide freely on rod until it contacts shoulder on rod.
Install connecting rod lock nut (9) and tighten against gear
ball. While tightening lock nut, prevent connecting rod from
turning by carefully holding with pipe wrench or vise grips
through inspection ports in suction housing.
6. Apply liberal amount of grease to gear ball teeth and
ring gear (8) teeth, and slide ring gear into the drive shaft
assembly. Keyways in ring gear should be facing out, and
one of the keyways should be aligned with drilled and tapped
holes in outside diameter of drive shaft.
7. Place keys (7) in keyways of the ring gear. A small
amount of grease may be used to hold the keys in place.
The flat face of the ring gear should be approximately flush
with the face of the drive shaft.
8. Place primary thrust plate (6) in drive shaft head (4),
aligning slot in outside diameter of thrust plate with pin in
drive shaft head. When the thrust plate is properly seated,
the face of the thrust plate should be flush with the face of
the drive shaft head.
9. Lubricate the spherical surface of the thrust plate and fill
the recess in the drive shaft head with grease.
10. Place O-ring (5) in the groove on drive shaft head (4).
Align the keyways in the drive shaft head with the keys in the
ring gear, and insert the head into the drive shaft assembly.
Note: If the threaded holes in the drive shaft do not align
with the holes in the drive shaft head, a strap wrench
or pipe wrench may be used to turn the drive shaft
slightly.
Page 11
11. Thread the six socket head screws (E) through the
drive shaft head into the drive shaft. Tighten them evenly
until face of drive shaft head is tight against face of drive
shaft. Excess grease in the gear joint assembly will be
purged from the holes in the drive shaft and drive shaft head.
Note: If the standard socket head screws are not long
enough initially to engage the threads in the drive
shaft, two longer screws may be used 180 degrees
apart to pull the drive shaft head close enough to the
drive shaft to engage the standard screws.
12. After the six socket head screws (E) are secured and
the grease has been purged from the assembly, install the
pipe plugs (C) in the drive shaft head and drive shaft. Also
install the locking set screw (D) in the drive shaft in the
threaded hole nearest the bearing housing.
13. If the stator was not previously tightened to the
suction housing (Section 4-31, step 5), it should be tightened
at this time.
4-33. Stator Support/Discharge Assembly
1. Place top of stator support(s) (31) over stator and
fasten to bottom half of stator supports using hex head
screws (L).
2. Place stator gasket (34) in recess in discharge flange
(37) and position discharge flange on end of stator. Align
holes in stator clamp ring (36B) with threaded holes in dis-
charge flange, and install and tighten hex head screws (M).
4-34. Final Assembly
1. Install inspection plates (32)to suction housing (29)
with gaskets (33), using hex head screws (P) and
lockwashers.
2. Install pipe plugs (Q and J) and zerk fittings (K) in ap-
propriate threaded holes in suction housing. Install pipe
plugs (N) in threaded holes in bearing housing, or attach
drain lines if preferred.
3. Connect power source. Turn on flush water to
packing if used. Open suction and discharge valves, and
start pump.
4-35. Packing Adjustment
For packing adjustment, refer to Section 4-3.
4-36. STORAGE
4-37. Short Term Storage. Storage of 6 months or less will
not damage the pump. However, to insure the best possible
protection, the following is advised:
1. Store pump inside whenever possible or cover with
some type of protective covering. Do not allow moisture to
collect around pump.
2. Remove drain plug and inspection plates to allow the
pump body to drain and dry completely. Replace inspection
plates.
3. Loosen the packing gland and inject a liberal amount of
grease into the stuffing box. Tighten the gland nuts only
hand tight. When water flush systems are to be used, do not
use grease. A small amount of light oil is recommended.
4. See drive manufacturer’s instructions for motor and/or
drive storage.

Page 12
5. See OPERATION Sections 3-1 through 3-4 before
startup. Be sure all lubricants are in good condition.
4-38. Long Term Storage. If pump is to be in storage for
more than 6 months, perform the above short term storage
procedures plus the following:
1. Occasionally rotate the pump manually a few revolu-
tions to avoid a “set” condition of rotor in stator elastomer.
This will prevent hard starting and excessive torque require-
ments when pump is again put into operation.
2. Apply rust inhibitor to all unpainted cast iron and
machined carbon steel surfaces.
3. Remove drive belts if applicable.
4-39. PACKING SPECIFICATION
Standard packing on all Moyno 2000 pumps consists of
braided PTFE fibers impregnated with ultra-fine graphite.
Optional types of packing are available for food, high
temperature and other types of service. Consult your nearest
Moyno representative.
4-40. VARIATIONS OF STANDARD PARTS
The following are variations available for modifying pumps
to meet specialized pumping conditions. If the trim code of
your pump is other than “AAA,” contact your nearest Moyno
representative for clarification. Do not modify your pump with
any variation unless you have determined that it is
compatible with your application.
The three-character trim code is designed as follows. The
first character identifies any sealing variations, the second
character identifies any internal variations, and the third
character identifies any rotor variations.
Sealing Variation
Internal Variation A A A
Rotor Variation
The trim code “AAA” represents a pump with standard fea-
tures. Deviations from standard are to be indicated by
changing the appropriate character from the choices listed.
When two or more letters are combined, dashes are used to
separate the three areas of the trim code for clarity.
SEALING VARIATIONS
A — BRAIDED TEFLON & GRAPHITE PACKING, (Black)
Standard to all lines except Quick Disassembly
pumps. Optional on Quick Disassembly pumps.
C — BRAIDED TEFLON PACKING, (White) Optional
packing on all lines.
D — DOUBLE MECHANICAL SEAL, Optional on all
lines. Not offered on #2 “L” frame.
F — BRAIDED TEFLON FOOD GRADE PACKING,
(White) Standard on all Quick Disassembly pumps.
Optional on all other lines.
G — 100% GRAPHITE PACKING, (Gray) Optional to all
lines.
H — FLUSH PACKING GLAND
S — SINGLE MECHANICAL SEAL, Optional on all lines.
W — WATER FLUSH, Optional on all lines.
X — Special to application
INTERNAL VARIATIONS
A — Standard plated shaft
B — Non-plated shaft
C — Solid drive shaft configuration
E — Extension tube with extended auger
F — Extended drive shaft (for back stop or large pulley)
G — Ceramic coated drive shaft
K — Tungsten carbide coated drive shaft
M — Chromium carbide coated drive shaft
R — Fiber deflector
S — Shaft sleeve
X — Special to application
ROTOR VARIATIONS
A — Standard size with chrome plating
B — Non-plated (no plating)
C — Standard undersize
E — Standard oversize
G — Ceramic coating
K — Tungsten carbide coating
M— Chromium carbide coating
X — Special to application
4-41. Rotors identified on parts listing are standard size
with hard chrome plated surface. Other variations of rotor
size and finish may be ordered by selecting the standard
rotor part number and changing the last digit of the rotor
number as follows:
2 = Standard size, non-plated
3 = Undersize, chrome-plated
4 = Undersize, non-plated
5 = Oversize, chrome-plated
Do not change rotor sizes without consulting your local
Moyno Sales Office. These variations are used for certain
specialized pumping conditions only.
4-42. Drive Shafts shown have hard-chrome plating on the
packing wear area. If non-plated drive shafts are required,
select the standard part number and change the last digit to
next higher number; example: PE0261 to PE0262. If the
optional shaft sleeve is used, refer to Table 4-13 and 4-14 for
appropriate part numbers.
TORQUE GUIDELINES CHART
Stainless Steel Bolts Carbon Steel Bolts
Size Max. Torque Size Max. Torque
N0. 10-24
1/4-20
5/16-18
3/8-16
1/2-13
22.8 in. lb.
75.2 in. lb.
132 in. lb.
236 in. lb.
517 in. lb.
5/16-18
3/8-16
1/2-13
5/8-11
3/4-10
10 ft. lb.
21.7ft. lb.
43.5ft. lb.
86 ft. lb.
152 ft. lb.
Connecting Rod Lock Nuts
Drive End Nut Size Max. Torque
E
F
G,H
J
K
9/16-18
3/4-16
7/8-14
1 1/4-12
11/2-12
25ft.lb.
35 ft. lb.
50ft.Ib.
85 ft. lb.
110 ft. lb.
Note: Torque values are from the Industrial Fasteners In-
stitute and Craftsman Corp.

4-43. STANDARD HARDWARE
Page 13
J220
3/4-10 X 2
3/4
J220
3/4-10 X 2
3/4
8
8
8
8
J065G1, J090G1
J115G1, J175G1,
J335G1, J220
3/4-10 X 4-1/2
6

Page 14
4-44. SELECTING THE CORRECT PART FOR YOUR
MOYNO 2000 PROGRESSING CAVITY PUMP
PUMP MODEL DESIGNATION
Table 4-1 Basic Drive End Parts: Select Reference Number part by Drive End (1G065G1 CDQ AAA) and
(Page 15) Type Designation (1G065G1 CDQ AAA) where listed.
Table 4-2 Wettable Castings (CD & CS): Select Reference Number part by Drive End and Element
(Page 16) (1G065G1 CDQ AAA) if Type Designation begins with CD or CS (1G065G1 CDQ AAA).
Table 4.3 Wettable Castings (SS): Select Reference Number part by Drive End and Element (1G065G1
(Page 17) SSQ AAA) if Type Designation begins with SS (1G065G1 SSQ AAA).
Table 4-4 Stators: Select Stator part number by Drive End and Element (1G065G1 CDQ AAA), and number
(Page 17) of stages (1G065G1 CDQ AAA). The last letter of the Type Designation (1G065G1 CDQAAA) must be
added as the sixth digit of the part number.
Table 4-5 Stator Gaskets: Select Stator Gasket part number by Drive End and Element (1G065G1 CDQ
(Page 18) AAA), and Type Designation (1G065G1 CDQ AAA).
Table 4-6 Stator Clamp Rings: Select Stator Clamp Ring part number by Drive End and Element (1G065G1
(Page 18) CDQ AAA), and number of stages (1G065G1 CDQ AAA).
Table 4-7 Connecting Rods: Select Connecting Rod part number by Drive End and Element (1G065G1
(Page 19) CDQ AAA), and Type Designation (1G065G1 CDQ AAA).
Table 4-8 Discharge Flanges (CD): Select Discharge Flange part number by Drive End and Element
(Page 19) (1G065G1 CDQ AAA), and number of stages (1G065 CDQ AAA), if Type Designation begins with CD.
Table 4-9 Discharge Flanges (CS & SS): Select Discharge Flange part number by Drive End and Element
(Page 20) (1G065G1 CSQ AAA), and number of stages (1G065 CSQ AAA), if Type Designation begins with CS or SS.
Table 4-10 Rotors (CD): Select Rotor part number by Drive End and Element (1G065G1 CDQ AAA), and
(Page 20) number of stages (1G065 CDQ AAA), if Type Designation begins with CD.
Table 4-11 Rotors (CS & SS): Select Rotor part number by Drive End and Element (1G065G1 CSQ AAA),
(Page 22) and number of stages (1G065 CSQ AAA), if Type Designation begins with CS or SS.
Table 4-12 Head Rings: Select Head Ring part number by Drive End and Element (1G065G1 CDQ AAA),
(Page 22) and Type Designation (1G065G1 CDQ AAA).
Table 4-13 Shaft Sleeve (CD): Select Reference Number part by Drive End and Element (1G065 CDQ AAA)
(Page 21) if Type Designation begins with CD (Shaft Sleeve Option only).
Table 4-14 Shaft Sleeve (CS & SS): Select Reference Number part by Drive End and Element (1G065 CSQ
(Page 21) AAA) if Type Designation begins with CS or SS (Shaft Sleeve Option only).

4-45. PARTS LIST Table 4-1. Parts List
DRIVE END SIZE
REF.
NO. DESCRIPTION E F G H J K
1 Radial Grease Seal ................................ AG0611 PF0611 PG0611 PH0611 PJ0611 PK0611
2 Bearing Cover Plate ............................... PE0341 PF0341 PG0341 PH0341 PJ0341 PK0341
3 O-Ring.................................................... PE110Q BJ112Q BK113Q PH110Q BH114Q PK110Q
4 Drive Shaft Head.................................... PE0971 PF0971 PG0971 PH0971 PJ0971 PK0971
5 O-Ring Shaft Head:................................ BE111Q BE113Q BG114Q BH111Q TJ111Q BK114Q
6 Primary Thrust Plate............................... PE0981 PF0981 PG0981 PH0981 PJ0981 PK0981
7 Key......................................................... RE0761 RF0761 RG0761 RH0761 RJ0761 RK0761
8 Ring Gear............................................... AE0952 AF0952 AG0952 AH0952 AJ0952 AK0952
9 Lock Nut ................................................. RE0581 RF0581 RG0581 RH0581 RJ0581 RK0581
10 Gear Ball................................................. AE0951 AF0951 AG0951 AH0951 AJ0951 AK0951
Gear Joint Kit (See Note C).................... KPE951 KPF951 KPG951 KPH951 KPJ951 KPK951
11 Secondary Thrust Plate.......................... PE0982 PF0982 PG0982 PH0982 PJ0982 PK0982
12 Seal Support........................................... PE0891 PF0891 PG0891 PH0891 PJ0891 PK0891
13 Gear Joint Seal:
CDQ, CSQ, SSQ, CDR, CSR, SSR.... PE087Q PF087Q PG087Q PH087Q PJ087Q PK087Q
CDB, CSB, SSB, CDF, CSF, SSF ...... PE087F PF087F PG087F PH087F PJ087F PK087F
Gear Joint Seal Kit (See Note D):
CDQ, CSQ, SSQ, CDR, CSR, SSR.... KPE87Q KPF87Q KPG87Q KPH87Q KPJ87Q KPK87Q
CDB, CSB, SSB, CDF, CSF, SSF ...... KPE87F KPF87F KPG87F KPH87F KPJ87F KPK87F
14 Drive Shaft:
CDQ, CDR, CDB, CDF ....................... PE0261 PF0261 PG0261 PH0261 PJ0261 PK0261
CSQ, CSR, CSB, CSF,
SSQ, SSR, SSB, SSF......................... PE0266 PF0266 PG0266 PH0266 PJ0266 PK0266
15 Tapered Roller Bearing........................... PE0311 PF0311 PG0311 PH0311 PJ0311 PK0311
Bearing Kit (See Note B) ........................ KPE291 KPF291 KPG291 KPH291 KPJ291 KPK291
16 Bearing Spacer....................................... PE0331 PF0331 PG0331 PH0331 PJ0331 PK0331
17 Bearing Lock Plug .................................. P10762 P10762 P10762 P10762 P10762 P10762
18 Bearing Lock Nut.................................... PE0581 PF0581 PG0581 PH0581 PJ0581 PK0581
19 Thrust Grease Seal ................................ AK0621 XK0621 PG0621 PH0621 Al4611 PK0621
20 Slinger Ring............................................ PE0771 PF0771 PG0771 PH0771 PJ0771 PK0771
21 Packing Gland Half (See Note A):
CDQ, CDR, CDB, CDF,
CSQ, CSR, CSB, CSF........................ PE041D PF041D PG041D PH041D PJ041D PK041D
SSQ, SSR, SSB, SSF......................... PE041S PF041S PG041S PH041S PJ041S PK041S
22 Packing (See Note A)............................. PE0423 PF0423 PG0423 PH0423 PJ0423 PK0423
23 Lantern Ring Half (See Note A).............. AE0571 PF0571 PG0571 PH0571 AJ0571 PK0571
24A Adapter Gasket:
CDB, CSB, SSB.................................. ----- BF085B BG085B BH085B ----- BK085B
CDQ, CDR, CSQ, CSR, SSQ, SSR.... ----- BF085Q BG085Q BH085Q ----- BK085Q
CDF, CSF, SSF .................................. ----- BF085F BG085F BH085F ----- BK085F
24B Adapter Gasket:
CDB, CSB, SSB.................................. ----- ----- ----- ----- BK085B -----
CDQ, CDR, CSQ, CSR, SSQ, SSR.... ----- ----- ----- ----- BK0B5Q -----
CDF,CSF,SSF .................................... ----- ----- ----- ----- BK085F -----
25A Adapter Bushing—See Tables 4-2 and 4-3
25B Adapter Bushing—See Tables 4-2 and 4-3
26 Bearing Housing..................................... PE0051 PF0051 PG0051 PH0051 PJ0051 PK0051
27 Retaining Ring........................................ AF0085 AG0085 PG0085 AH0085 PJ0085 PK0085
28 Clamp Ring............................................. AF0932 AG0932 PG0932 AH0932 PJ0932 PK0932
29 Suction Housing—See Tables 4-2 and 4-3
30 Stator—See Table 4-4
31 Stator Support—See Tables 4-2 and 4-3
32 Inspection Plate:
CDQ, CDR, CDB, CDF,
CSQ, CSR, CSB, CSF........................ BE0171 BF0171 BF0171 BF0171 BH0171 BJ0171
SSQ, SSR, SSB, SSF......................... BE0176 BF0176 BF0176 BF0176 BH0176 BJ0176
-K800 CDQ, CDR, CDB, CDF,
CSQ, CSR, CSB, CSF................. ----- ----- ----- ----- ----- BJ0172
SSQ, SSR, SSB, SSF.................. ----- ----- ----- ----- ----- BJ0177
33 Inspection Plate Gasket:
CDB, CSB, SSB.................................. BE079B BF079B BF079B BF079B BH079B BJ079B
CDQ, CDR, CSQ, CSR, SSQ, SSR.... BE079Q BF079Q BF079Q BF079Q BH079Q BH079Q
CDF, CSF, SSF .................................. BE079F BF079F BF079F BF079F BH079F BH079F
34 Stator Gasket—See Table 4-5
35 Retaining Ring—See Tables 4-2 and 4-3
Part List Continued on Page 16.
Page 15

Page 16
4-45. PARTS LIST (Cont.) Table 4-1. Parts List (Cont.)
DRIVE END SIZE
REF.
NO. DESCRIPTION E F G H J K
36A Stator Ring Clip–See Table 4-6
36B Stator Clamp Ring–See Table 4-6
37 Discharge Flange–See Table 4-8
38 Connecting Rod–See Table 4-7
39 Gear Joint Shell:
CDQ, CDR, CDB, CDF ....................... PE0911 PF0911 PG0911 PH0911 PJ0911 PK0911
CSQ, CSR, CSB, CSF,
SSQ, SSR, SSB, SSF......................... PE0916 PF0916 PG0916 PH0916 PJ0916 PK0916
40 Rotor–See Tables 4-10 and 4-11
41 O-ring:
CDQ, CDR, CSQ, CSR, SSQ, SSR .. PE113Q PF113Q PG113Q PH113Q PJ113Q PK113Q
CDB, CSB, SSB................................ PE113B PF113B PG113B PH113B PJ113B PK113B
CDF, SCF,SSF.................................. PE113F PF113F PG113F PH113F PJ113F PK113F
42 Head Ring–See Table 4-12
43 Shaft Sleeve Kit–See Table 4-13
Note A: For pumps with shaft sleeve, see pages 21, 24 and 25.
Note B: Bearing Kit includes items 1, 15(2), 19.
Note C: Gear Joint Kit includes items 6, 7(2), 8, 10, 11, 12.
Note D: Gear Joint Seal Kit includes items 5, 13, 41.
Table 4-2. Parts List —Type Designation Begins with CD or CS
REF. NO:
MODEL
25A
ADAPTOR
BUSHING
25B
STATOR
ADAPTOR
29
SUCTION
HOUSING
31
STATOR
SUPPORT
35
RETAINING
RING (2)
E008
E012, E018E
E022, E033E
E036
E050
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
PE0021
PE0021
PE0022
PE0031
PE0031
BE0381
BE0381
BE0382
PE0381
PE0381
AE0085
AE0085
AF0085
AG0085
AG0085
F012
F022
F036, F054E
F050, F075E
F065
F090
BF0511
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
PF0021
PF0021
PF0022
PF0022
PF0031
PF0031
BF0383
BF0381
BF0382
BF0382
PF0381
PF0381
AE0085
AF0085
AG0085
AG0085
AH0085
AH0085
G022
G036
G050
G065, G098E
G090
G115
BG0511
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
PG0021
PG0021
PG0021
PG0022
PG0022
PG0031
BG0383
BG0381
BG0381
BG0382
BG0382
BG0382
AF0085
AG0085
AG0085
AH0085
AH0085
AH0085
H036
H065
H090
H115
H175
BH0511
-----
-----
-----
-----
-----
-----
-----
-----
-----
PH0021
PH0021
PH0021
PH0021
PH0031
BH0382
BH0381
BH0381
BH0381
BJ0381
AG0085
AH0085
AH0085
AH0085
AK0084
J065
J090
J115
J175, J220
J335
J345
-----
-----
-----
-----
-----
-----
PJ0511
-----
-----
-----
-----
-----
PJ0021
PJ0021
PJ0021
PJ0022
PJ0022
PJ0022
BH0381
BH0381
BH0381
BJ0381
BH0381
BH0381
AH0085
AH0085
AH0085
AK0084
AK0084
AK0084
K115
K175
K335
K345
K620
K800
BK0511
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
PK0021
PK0021
PK0021
PK0021
PK0021
PK0022
BK0382
BK0381
BK0381
BK0381
BK0381
BK0383
AH0085
AK0084
AK0084
AK0084
AK0084
AK0085

Page 17
Table 4-3. Parts List —Type Designation Begins with SS
REF. NO: 25A 25B 29 31 35
ADAPTOR STATOR SUCTION STATOR RETAINING
MODEL BUSHING ADAPTOR HOUSING SUPPORT RING (2)
E008 ----- ----- PE0026 BE0381 AE0085
E012, E018E ----- ----- PE0026 BE0381 AE0085
E022, E033E ----- ----- PE0027 BE0382 AF0085
E036 ----- ----- PE0032 BE0381 AG0085
E050 ----- ----- PE0032 BE0381 AG0085
F012 BF0516 ----- PF0026 BF0383 AE0085
F022 ----- ----- PF0026 BF0381 AF0085
F036, F054E ----- ----- PF0027 BF0382 AG0085
F050, F075E ----- ----- PF0027 BF0382 AG0085
F065 ----- ----- PF0032 PF0381 AH0085
F090 ----- ----- PF0032 PF0381 AH0085
G022 BG0516 ----- PG0026 BG0383 AF0085
G036 ----- ----- PG0026 BG0381 AG0085
G050 ----- ----- PG0026 BG0381 AG0085
G065, G098E ----- ----- PG0027 BG0382 AH0085
G090 ----- ----- PG0027 BG0382 AH0085
G115 ----- ----- PG0032 BG0382 AH0085
H036 BH0516 ----- PH0026 BH0382 AG0085
H065 ----- ----- PH0026 BH0381 AH0085
H090 ----- ----- PH0026 BH0381 AH0085
H115 ----- ----- PH0026 BH0381 AH0085
H175 ----- ----- PH0032 BJ0381 AK0084
J065 ----- ----- PJ0026 BH0381 AH0085
J090 ----- ----- PJ0026 BH0381 AH0085
J115 ----- ----- PJ0026 BH0381 AH0085
J175, J220 ----- ----- PJ0027 BJ0381 AK0084
J335 ----- PJ0516 PJ0027 BH0381 AK0084
J345 ----- ----- PJ0032 BH0381 AK0084
K115 BK0516 ----- PK0026 BK0382 AH0084
K175 ----- ----- PK0026 BK0381 AK0084
K335 ----- ----- PK0026 BK0381 AK0084
K345 ----- ----- PK0026 BK0381 AK0084
K620 ----- ----- PK0026 BK0381 AK0084
K800 ----- ----- PK0027 BK0383 AK0085
Table 4-4. Stator (Ref. No. 30) Part Number
STAGES
MODEL 1 2 3 4 6 9
E008 C3108† C3208† ----- C3408† C3608† -----
E012 C310E† C320E† ----- C340E† C360E† -----
E018E E3118† E3218† ----- ----- ----- -----
E022 C310F† C320F† ----- C340F† ----- -----
E033E E3133† E3233† ----- ----- ----- -----
E036 C310G† C320G† ----- ----- ----- -----
E050 C3150† C3250† ----- ----- ----- -----
F012 ----- ----- ----- ----- C360E† C390E†
F022 C310F† C320F† ----- C340F† C360F† -----
F036 C310G† C320G† ----- C340G† ----- -----
F050 C3150† C3250† ----- C3450† ----- -----
F054E E3154† E3254† ----- ----- ----- -----
F065 C310H† C320H† ----- ----- ----- -----
F075E E3175† E3275† ----- ----- ----- -----
F090 C3190† C3290† ----- ----- ----- -----
G022 ----- ----- ----- ----- C360F† C390F†
G036 C310G† C320G† ----- C340G† C360G† -----
G050 ----- C3250† ----- C3450† C3650† -----
G065 C310H† C320H† ----- C340H† ----- -----
G090 C3190† C3290† ----- C3490† ----- -----
G098E E3198† E3298† ----- ----- ----- -----
G115 C310J† C320J† ----- ----- ----- -----
H036 ----- ----- ----- ----- C360G† C390G†
H065 C310H† C320H† ----- C340H† C360H† -----
H090 ----- C3290† ----- C3490† C3690† -----
H115 C310J† C320J† ----- C340J† ----- -----
H175 C310K† C320K† ----- ----- ----- -----
J065 ----- ----- ----- ----- C360H† C390H†
J090 ----- ----- ----- ----- C3690† -----
J115 C310J† C320J† ----- C340J† C360J† -----
J175 C310K† C320K† ----- C340K† ----- -----
J220 C3120H C3220H ----- ----- ----- -----
J335 C3123† C3223† ----- ----- ----- -----
J345 C3145† C3245† ----- ----- ----- -----
K115 ----- ----- ----- ----- C360J† C390J†
K175 C310K† C320K† ----- C340K† C360K† -----
K335 C3123† C3223† C3323† ----- ----- -----
K345 C3145† C3245† C3345† ----- ----- -----
K620 C3162† C3262† ----- ----- ----- -----
K800 C3180† C3280† ----- ----- ----- -----
† Add third letter of Type Designation to complete the part number; i.e., for Type CDQ, add Q to basic number of stator.

Page 18 Table 4-5. Stator Gasket (Ref. No. 34) Part Number
TYPE DESIGNATION
CDQ, CSQ, SSQ,
MODEL CDR,CSR, SSR CDF, CSF, SSF CDB, CSB, SSB
E008, E012, E018E, F012 BE085Q BE085F BE085B
E022, E033E, F022, G022 BF085Q BF085F BF085B
E036, F036, F054E, G036, H036 BG085Q BG085F BG085B
E050, F050, F075E, G050, G075E BG085Q BG085F BG085B
F065, G065, G098E, H065, J065 BH085Q BH085F BH085B
F090, G090, H090, J090 BH085Q BH085F BH085B
G115, H115, J115, K115 BH085Q BH085F BH085B
H175, J175, K175, K345, J220 BK085Q BK085F BK085B
J345, K620, J335, K335 BK085Q BK085F BK085B
K800 BK086Q BK086F BK086B
Table 4-6. Stator Clamp Ring (Ref. No. 36A & 36B) Part Number
STAGES
1, 2, AND 3 4 6 9
MODEL 36A & 36B 36A 36B 36A 36B 36A 36B
E008 AE0932 AE0932 AE0993 AE0932 AE0993 ----- -----
E012, E018E AE0932 AE0932 AE0993 AE0932 AE0993 ----- -----
E022, E033E AF0932 AF0932 AF0932 ----- ----- ----- -----
E036 AG0932 ----- ----- ----- ----- ----- -----
E050 AG0932 ----- ----- ----- ----- ----- -----
F012 ----- ----- ----- AF0933 AF0992 AF0933 AF0992
F022, F033E AF0932 AF0932 AF0993 AF0932 AF0993 ----- -----
F036, F054E AG0932 AG0932 AG0932 ----- ----- ----- -----
F050, F075E AG0932 AG0932 AG0932 ----- ----- ----- -----
F065 AH0932 ----- ----- ----- ----- ----- -----
F090 AH0932 ----- ----- ----- ----- ----- -----
G022 ----- ----- ----- AG0933 AG0992 AG0933 AG0992
G036 AG0932 AG0932 AG0993 AG0932 AG0993 ----- -----
G050, G075E AG0932 AG0932 AG0993 AG0932 AG0993 ----- -----
G065, G098E AH0932 AH0932 AH0932 ----- ----- ----- -----
G090 AH0932 AH0932 AH0932 ----- ----- ----- -----
G115 AH0932 ----- ----- ----- ----- ----- -----
H036 ----- ----- ----- AH0933 AG0993 AG0933 AG0993
H065 AH0932 AH0932 AH0993 AH0932 AH0993 ----- -----
H090 AH0932 AH0932 AH0993 AH0932 AH0993 ----- -----
H115 AH0932 AH0932 AH0932 ----- ----- ----- -----
H175 AK0932 ----- ----- ----- ----- ----- -----
J065 ----- ----- ----- AH0932 AJ0992 AH0932 AJ0992
J090 ----- ----- ----- AH0932 AJ0992 ----- -----
J115 AH0932 AH0932 AH0993 AH0932 AH0993 ----- -----
J175 AK0932 AK0932 AK0932 ----- ----- ----- -----
J335, J220 AK0932 ----- ----- ----- ----- ----- -----
J345 AK0932 ----- ----- ----- ----- ----- -----
K115 ----- ----- ----- AK0933 AJ0992 AK0933 AJ0992
K175 AK0932 AK0932 WK0932 AK0932 WK0932 ----- -----
1K335 AK0932 ----- ----- ----- ----- ----- -----
2K335 AK0932 & WK0932 ----- ----- ----- ----- ----- -----
3K335 AK0932&WK0932 ----- ----- ----- ----- ----- -----
1K345 AK0932 ----- ----- ----- ----- ----- -----
2K345 AK0932 & WK0932 ----- ----- ----- ----- ----- -----
3K345 AK0932 & WK0932 ----- ----- ----- ----- ----- -----
1K620 AK0932 ----- ----- ----- ----- ----- -----
2K620 AK0932 ----- ----- ----- ----- ----- -----
1K800 AK0934 ----- ----- ----- ----- ----- -----
2K800 AK0934 ----- ----- ----- ----- ----- -----