Mr. Coffee EHXSS Series User manual

User Manual /Manual del Usuario
Coffeemaker / Cafetera
EHXSS Series
© 2020 Sunbeam Products, Inc. All rights reserved.
Distributed by Sunbeam Products, Inc., Boca Raton, Florida
33431.
U.S. 1-800-MR COFFEE (1-800-672-6333)
Canada 1-800-667-8623
Visit us at www.mrcoffee.com
You will find exciting and entertaining tips and ideas,
including great recipes!
© 2020 Sunbeam Products, Inc. Todos los derechos
reservados. Distribuido por Sunbeam Products, Inc. Boca
Raton, Florida 33431.
Visítenos en www.mrcoffee.com
Ahí encontrará consejos e ideas excitantes y entretenidos,
¡incluyendo excelentes recetas!
www.mrcoffee.com
Printed in China/Impreso en China P.N. 202474
BVMC-EHX33 Series_20ESM1 GCDS-MRC-SL

IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and/or injury to persons including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electric shock, do not place or
immerse cord, plugs, or appliance in water or other
liquid.
4. This appliance is not intended for use by children
or by persons with reduced physical, sensory,
or mental capabilities, or lack of experience and
knowledge. Close supervision is necessary when any
appliance is used near children. Children should be
supervised to ensure that they do not play with the
appliance. Keep the appliance and its cord out of
reach of children.
5. Unplug from outlet when either the appliance or
display clock (if provided) is not in use, and before
cleaning. Allow to cool before putting on or taking
off parts, and before cleaning the appliance.
6. Do not operate any appliance with a damaged cord
or plug or after the appliance malfunctions, or has
been damaged in any manner. Return appliance
to an Authorized Service Center for examination,
repair or adjustment. Do not attempt to replace or
splice a damaged cord.
7. The use of an accessory not recommended by the
appliance manufacturer for use with this appliance
may result in fire, electric shock or injury to persons.
8. Do not use outdoors.
2 3
9. Do not let cord hang over edge of table or counter,
or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner,
or in a heated oven.
11. Always attach plug to appliance first, then plug cord
into the wall outlet (for appliances with detachable
cords). To disconnect, turn any control to the off
position, then remove plug from wall outlet.
12. Do not use appliance for other than intended use.
13. All lids should be closed during use.
14. Scalding may occur if the lid is removed or brew
basket door is opened during or immediately after
the brewing cycles. Contents may be hot. Allow to
cool before opening the lid.
For appliances with glass containers:
15. The container is designed for use with this
appliance. It must never be used on a range top.
16. Do not set a hot container on a wet or cold surface.
17. Avoid sudden temperature changes, such as rinsing,
washing, filling, or immersing a hot container with
cold liquids.
18. Do not use a cracked or chipped container or a
container having a loose or weakened handle.
19. Do not clean container with cleansers, steel wool
pads, or other abrasive material.
For appliances with service panels:
20. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT REMOVE THIS COVER. NO USER–
SERVICEABLE PARTS INSIDE. REPAIR SHOULD BE DONE
BY AUTHORIZED SERVICE PERSONNEL ONLY.
SAVE THESE INSTRUCTIONS

4
INTRODUCTION
Welcome and congratulations on the purchase of your
new MR. COFFEE
®
Coffeemaker. Your new EHX Series
coffeemaker will wake up with you in the morning
and provide you breaks and treats during your hectic
daily activities. How you enjoy your MR. COFFEE
®
Coffeemaker is up to you!
5
HOUSEHOLD USE ONLY
This appliance has a polarized
plug (one blade wider than
the other). As a safety feature
to reduce the risk of electrical shock, this plug is
intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety
feature or modify the plug in any way. If the plug fits
loosely into the AC outlet or if the AC outlet feels
warm do not use that outlet.
POLARIZED PLUG
POWER CORD INSTRUCTIONS:
A short power-supply cord (or detachable power-
supply cord) may be provided to reduce risks resulting
from becoming entangled in or tripping over a longer
cord. Longer detachable power-supply cords or
extension cords are available and may be used if care
is exercised in their use. If a long detachable power-
supply cord or extension cord is used:
a. The marked electrical rating of the detachable
power-supply cord or extension cord should
be at least as great as the electrical rating of the
appliance;
b. If the appliance is of the grounded type, the
extension cord should be a grounding type 3-wire
cord; and
c. The longer cord should be arranged so that it will
not drape over the counter top or table top where
it can be pulled on by children or tripped over
unintentionally.
Do not pull, twist or otherwise abuse the power cord.
PRODUCT NOTICES
1. Place the appliance on a hard, flat, level surface
to avoid interruption of airflow underneath the
coffeemaker.
2. Glass decanters only: Discard the decanter
immediately if it is ever boiled dry.
3. Glass decanters only: Protect the decanter from
sharp blows, scratches or rough handling.
4. Do not operate the appliance with an empty water
tank.
5. Keep the area above the appliance clear during
use, as hot steam will escape the appliance.

76
TABLE OF CONTENTS
Important Safeguards..............................................................2
Introduction..............................................................................4
Carafe Use and Care...............................................................4
Special Cord Set Instructions..................................................4
Table of Contents.....................................................................6
Parts Diagram...........................................................................7
Coffeemaker Features and Benefits.....................................9
Clean Your Coffeemaker Before Using the First Time.........10
Setting the Clock and Brew Later Function...........................11
Preparing for Use....................................................................12
• Suggested Coffee Measurement Chart
• Adding Water and Ground Coffee
• Water Filtration System (not included)
Brewing Coffee Now................................................................15
Brewing Coffee Later (Brew Later).........................................16
CleaningandMaintainingYourCoffeemaker...........................17
Troubleshooting Your Mr. Coffee®Coffeemaker....................21
Service and Maintenance......................................................20
WarrantyInformation..............................................................26
1. Brew Basket
Lid
2. Shower Head
3. Water
Reservoir
4. Water Window
5. Pause ‘n Serve
6. Warming Plate
7. Carafe
8. Removable
Filter Basket
9. Coffee
Measuring
Scoop
PARTS DIAGRAM
1
2
3
4
5
6
79
8

8 9
a. Clock Display /
Freshness Timer Display
b. Minute Button
c. Clock Display /
Freshness Timer Button
d. Brew Strength Selector
(Regular / Strong)
e. Brew Strength Button
f. Select/Off Button
g. Brew Now Indicator
h. Brew Later Indicator
i. Set Brew Later Button
j. Hour Button
CONTROL PANEL
Coffeemaker Extras (not included with all models)
Water Filtration
System Mr. Coffee
®
Brand
Reusable Coffee Filter
COFFEEMAKER FEATURES AND BENEFITS
Your new MR. COFFEE
®
coffeemaker has the following
features:
• Brewing Capacity – 12 cups – glass carafe series
• Removable Filter Basket – The filter basket lifts out
for fast and easy cleaning and filling.
• Pause ‘n Serve – Can’t wait for the coffee to finish
brewing? The Pause ‘n Serve feature allows you up
to 30 seconds to pour a cup of coffee while the
coffeemaker is still brewing. Carefully remove the carafe
and the Pause ’n Serve feature will be automatically
activated, temporarily stopping the flow of coffee into
the carafe.
• Water Window – Show amount of water in the
reservoir for accurate filling.
• Non-Stick Warming Plate – This feature allows you
to keep your coffee hot after brewing. The non-
stick attribute prevents the carafe from sticking to
the surface of the warming plate.
• Brew Strength Selector – Adjusts the brewing time
to create a more full-flavored coffee.
• Water Filtration Capable – Great tasting coffee
begins with great water! Using the Mr. Coffee
®
carbon-based water filter in the Mr. Coffee
®
coffeemaker during the brewing process helps
remove up to 97% of the chlorine from the water
and improves the taste of your coffee. If you would
like to purchase a filter please visit
www.mrcoffee.com.
• Cord Storage – Safely stores excess cord to keep
your countertop neat.
• 2 Hour Auto Shut-Off – Keeps your coffee hot for
two hours, then automatically shuts off.
a
b
h
f
i
j
e
d
dc
g
Coffee Measuring Scoop

Your coffeemaker is now ready to use. Enjoy it!
SETTING THE CLOCK AND DELAY BREW LATER TIME
To Set the Clock:
1. Plug the power cord into a standard
electrical outlet. The clock will flash on
the control panel to indicate that the
time has not been set yet.
2. Press and hold the HOUR and MINUTE
buttons until you reach the current time.
The AM or PM indicator will light at the
bottom of the display (Figures 1 and 2).
The clock is now set!
NOTE: Pressing any button before setting the
clock will cause the clock to start keeping time
from 12:00 a.m. You must set the clock if you
want to use the Brew Later feature.
To Set the Delay Brew Later Time:
While the display is in the clock mode,
simply press the Set Brew Later button
(Figure 3) and, while the Brew Later light is
flashing, set the brew time by pressing the
HOUR and MINUTE buttons. The AM or PM
indicator will light at the left of the clock
display. (Figure 4)
Within a few seconds the display will change
to the current time.
The Brew Later Time is now set!
NOTE: To activate the BREW LATER cycle, see
the “Brewing Coffee Later” section.
To check the programmed time, push the
SET BREW LATER button. The display will
10 11
• Programmable Controls:
– Clock – The clock serves as a handy kitchen clock
and allows you to set the Brew Later feature and
functions as the Freshness Timer feature.
– Freshness Timer feature – Lets you know how
long your coffee has been waiting for you.
– Brew Later – Would you like to wake up to a
fresh pot of coffee? The timer allows you to
preset when you would like the coffeemaker to
automatically begin brewing your coffee, up to 24
hours in advance.
NOTE: If you have selected any of the operating
functions, the coffeemaker will act upon the last
operation selected if the power is restored within 10
seconds after a power outage.
CLEAN YOUR COFFEEMAKER BEFORE USING THE
FIRST TIME
Make sure your first cup of coffee is as good as can be
by cleaning your MR. COFFEE
®
Coffeemaker before its
first use. Just follow these simple steps:
1. Wash the carafe, carafe lid and the filter basket in
a mixture of mild detergent and water. Rinse each
thoroughly (please refer to the parts diagram listed
above).
2. Replace all the parts and close the lid. Then, run a
brew cycle with water only, without adding coffee
and coffee filter.
3. When brewing is complete,
turn your coffeemaker off,
discard the water in the
carafe and rinse the carafe,
carafe lid, and filter basket.
Figure 1
Figure 2
Figure 3
Figure 4

If you are using the water filtration
system first, look for the MR.
COFFEE
®
Filter Friendly symbol
on the bottom of your filter
basket. If you do not see this
symbol, please call 1-800-672-
6333.
To use the water filtration system
in your MR.COFFEE
®
Coffeemaker, please
follow these steps:
1. Align the red indicator on the frame
to the letter that corresponds with the
month that you are using the disk for the
first time. This serves to remind you to
change the disk every month (approx.
30 brewing cycles). To change the disk,
remove the used disk, insert new disk
into the frame.
NOTE: For optimum results, use the water
filtration system with a permanent filter.
2. Rinse the water filter in fresh water
before first use.
3. Follow Adding Water and Coffee
instructions.
4. When you are done brewing
your coffee, rinse the water
filter with fresh water. Do not
put your water filter in the dishwasher.
C. Adding Water and Ground Coffee
1. Open the brew basket lid. For your convenience,
you can lift out the removable filter basket.
12 13
show the time you have programmed the coffee to
brew. If you press the SET BREW LATER button again or
wait a few seconds, the display will switch back.
PREPARING FOR USE
Selecting and Measuring Ground Coffee
For best results, use the included coffee measuring scoop
for ground coffee measurements. Make sure you use
medium grind coffee for a perfect brew.
A. Suggested Coffee Measurement Chart
For best results, brew 4 of more cups of coffee.
Water To Brew Ground Coffee
12 cups = 60 oz. 3 scoops = 9 tbs.
10 cups = 50 oz. 2.5 scoops = 7.5 tbs.
8 cups = 40 oz. 2 scoops = 6 tbs.
6 cups = 30 oz. 1.5 scoops = 4.5 tbs.
4 cups = 20 oz. 1 scoop = 3 tbs.
Bonus: For a BOLDER CUP, use heaping scoops.
NOTE: The coffee measuring scoop is 3 tablespoons
total.
B. Water Filtration System
Using the Mr. Coffee
®
carbon-based water filter in the Mr.
Coffee
®
coffeemaker during the brewing process helps
remove up to 97% of the chlorine from the water and
improves the taste of your coffee. If you would like to
purchase a filter please visit www.mrcoffee.com.
Frame
Filter Disk
Red
Indicator

7. Lift the pour through reservoir lid and pour the
water into the water reservoir. Close the lid and
place the empty carafe onto the warmer plate.
NOTE: Make sure the carafe is fully placed on the
warming plate or the water and the grounds will
overflow from the filter basket. An overflow may cause
personal injury or damage to property.
CAUTION! To reduce the risk of damaging the
carafe and/or the risk of personal injury, do
not add cold water to the carafe if the carafe
is already hot. Allow the carafe to cool before
using.
BREWING COFFEE NOW
1. After completing the steps in the Adding Water and
Coffee section and with the glass carafe and the filter
basket securely in place, turn the coffeemaker on by
pressing the SELECT button once. The BREW NOW and
REGULAR green light will turn on to signal
that the coffeemaker is on and brewing
(Figure 6).
2. To enjoy a more full flavored cup of
coffee, press the Brew Strength button
once. The STRONG Brew Strength amber
light will turn on. The coffeemaker will
remain in the Brew Strength you have
selected until you change it back to
REGULAR strength by pressing the Brew
Strength button or until you unplug the
machine (Figure 7).
3. After the used coffee grounds have
cooled, carefully remove the filter
basket and discard them.
14 15
2. Place a 10-12 cup paper basket-
style filter or a MR. COFFEE
®
reusable permanent coffee filter
into the removable filter basket
(Figure 5).
NOTE: If using paper filters, it is
important that the sides of the
filter fit flush against the side of
the filter basket. If filter collapse
occurs, dampen the filter before
placing in the filter basket and adding
ground coffee and water.
3. Add the desired amount of coffee and gently shake
to level the coffee. See the Suggested Coffee
Measurement Chart.
4. If you are using water filtration system, place the MR.
COFFEE
®
water filter in the basket, making sure that
the side marked “this side up” faces you and that
the water filter is level.
5. Be sure the removable filter basket is properly
centered and all the way down in the brew basket
and close the lid.
6. Fill the carafe with cold, fresh water to the
desired capacity (1 cup equals 5 ounces) For
easy and accurate filling, the water markings on
the glass carafe and on the dual water windows
show the amount of water needed to make the
corresponding desired number of cups. Do not fill
past the “12 cup MAX line” or water will flow out of
the overfill hole in the back of the coffeemaker.
The amount of coffee brewed will always be slightly
less than the amount of water poured in the water
reservoir. This is due to the minimum absorption of
water by the coffee grounds.
Figure 5
Figure 6
Figure 7

2. Prepare your coffeemaker as described in “Adding
Water and Ground Coffee” section.
3. To activate Brew Later and program
your coffeemaker to brew coffee at
a later time, press the SELECT button
twice (Figure 9). The Brew Later light will
turn on. The coffeemaker is now set to
automatically brew coffee at the pre-set
later time. At this time the REGULAR light
will turn on. You can select the strength
that you desire by pressing the BREW STRENGTH
button. (Amber for STRONG, green for REGULAR)
4. At the pre-set time, the green BREW NOW light will
turn on and the Brew Later Amber light will turn off,
indicating the brewing has started in the selected
brew strength. The Freshness Timer feature will start.
5. The coffeemaker warmer plate will keep your coffee
hot for 2 hours and then automatically turn off.
As a safety feature, your coffeemaker will NOT start
again automatically the next day. If you want your
coffee to brew at the same time the following day,
simply add a new filter, coffee and water and set Brew
Later, by repeating Steps 2 and 3 above.
To cancel Brew Later: Press the SELECT button three
times until all lights turn off (Figure 9).
CLEANING AND MAINTAINING YOUR COFFEEMAKER
Daily Cleaning
Always unplug the coffeemaker and allow to cool
before cleaning.
Remove the filter basket, permanent filter (not
Caution: The shower head cover is hot after brewing.
Always allow the coffeemaker to cool down before cleaning.
4. Prior to making a second pot of coffee, turn the
coffeemaker off. This will reset the Freshness Timer
feature. To turn the coffeemaker off, press the
SELECT/OFF button all lights will turn off.
5. Make sure the carafe is empty before starting to
brew coffee.
6. Be sure to turn your coffeemaker off when no
longer using it.
The Freshness Timer Feature
The Freshness Timer feature lets you know
how long your coffee has been waiting
for you. At the start of the brew cycle, the
Freshness Timer feature will automatically be
activated.
Press the Freshness Timer TIMER button
once (Figure 8) and the clock time will
change to show the amount of time that has passed
since brewing completed. Push again to display current
time.
NOTE: The BREW NOW green light must be on for the
Freshness Timer feature to operate. The time and delay
brew later time cannot be set when the freshness timer
is displayed.
BREWING COFFEE LATER
1. You must first set the time for when you would like
the coffeemaker to begin brewing your coffee as
described in “Setting the Clock and the Brew Later
Timer” section.
16 17
Figure 8
Figure 9

7. Discard the cleaning solution and rinse the carafe
thoroughly with clean water.
8. Fill the water reservoir with clean, fresh water.
9. Place the empty carafe back on the coffeemaker,
centered on the warming plate.
10. Remove and discard the paper filter used during
the cleaning cycle. If a Mr. Coffee
®
permanent filter
was used during cleaning, remove it and rinse it
thoroughly before replacing it in the filter basket.
11. Begin brewing and allow the full brew cycle to complete.
12. Repeat steps 8 through 11 one more time.
Your coffeemaker is now clean and ready to brew the
next pot of delicious, hot coffee!
18
included), carafe and carafe lid and wash them in a
solution of hot water and mild liquid soap.
Never use abrasive cleansers, steel wool pads or other
abrasive materials. Dishwasher top rack safe parts: glass
carafe and lid, filter basket and permanent filter (not
included). The water filter disk (not included) is not
dishwasher safe.
CAUTION! Never immerse the coffeemaker
itself in water, in any other liquid or place in
the dishwasher.
Decalcifying your MR. COFFEE®Coffeemaker
Minerals (calcium/limestone) found in water will
leave deposits in your coffeemaker and affect its
performance. It’s recommended that you regularly
remove these deposits using vinegar.
1. Pour 4 cups or 20 fl. oz. of undiluted, white
household vinegar into the water reservoir. If using
water filtration disk, remove the water filtration disk
from the machine before decalcifying.
2. Place an empty 10-12 cup basket-style paper filter
or MR. COFFEE
®
permanent filter into the filter
basket and close the brew basket lid.
3. Place the empty carafe back in the unit, centered
on the warming plate.
4. Press Brew Now and leave coffeemaker on until the
all the vinegar has cycled through.
5. Turn the coffeemaker off and let stand for 30 minutes.
6. Run the remainder of the cleaning solution through
the coffeemaker.
Type of Water
Soft Water
Hard Water
Cleaning Frequency
Every 80 Brew Cycles
Every 40 Brew Cycles
Suggested Decalcifying Interval
19

21
TROUBLESHOOTING YOUR MR. COFFEE®COFFEEMAKER
Your MR. COFFEE
®
Coffeemaker has been carefully
designed to give you many years of trouble-free service.
In the unlikely event that your new coffeemaker does
not operate satisfactorily, please review the following
potential problems and try the steps recommended
BEFORE you call an Authorized Sunbeam Service Center.
PROBLEM POSSIBLE CAUSE SOLUTION
THE “BREW
NOW”/ON LIGHT
DOES NOT LIGHT
UP
The appliance is
unplugged. PLUG UNIT IN.
There’s a power
outage. WAIT FOR POWER TO BE RESTORED.
THE COFFEE IS
NOT BREWING The appliance is unplugged. PLUG UNIT IN.
There’s a power
outage. WAIT FOR POWER TO BE RESTORED.
The water
reservoir is empty. CHECK THE WATER WINDOWS.
The filter basket
is not properly
inserted.
INSERT FILTER BASKET
CORRECTLY.
The carafe is
not placed all
the way on the
warming plate.
PLACE Carafe
CORRECTLY ON
WARMING PLATE.
THE
COFFEEMAKER
ONLY BREWS
WATER
There are no
coffee grounds
in the filter
basket.
ADD THE DESIRED
AMOUNT OF COFFEE
TO THE FILTER.
20
Water Filtration Disk Replacement
Your water filtration disk will need to be replaced
once a month (approx. 30 brew cycles). If the machine
will not be in use for an extended period of time,
rinse the water filter with running water and clean the
coffeemaker before use.
Cleaning the Carafe
Hard water can leave a whitish stain on the carafe, and
coffee may then turn this stain brown.
To remove carafe stains:
1. Fill the carafe with a solution of equal parts water
and vinegar and let the solution stand in the carafe
for approximately 20 minutes.
2. Discard the solution, then wash and rinse the
carafe.
Do not use harsh abrasive cleaners that may scratch the
carafe, scratches may cause the carafe to break.
This appliance has no user serviceable parts. Any
servicing beyond that described in the Cleaning
Section should be performed by an Authorized Service
Representative only. See warranty available online.

22 23
PROBLEM POSSIBLE CAUSE SOLUTION
THE
COFFEEMAKER
BREWS SLOWLY
The coffeemaker
needs cleaning. CLEAN COFFEEMAKER AS DESCRIBED IN
“CLEANING AND
MAINTAINING”
SECTION.
THE FILTER
BASKET
OVERFLOWS
The filter basket
is not properly
inserted.
INSERT FILTER BASKET
CORRECTLY.
The carafe is
not placed all
the way on the
warming plate.
PLACE Carafe
CORRECTLY ON
WARMING PLATE.
The carafe lid is
not on carafe. PLACE LID ON THE Carafe.
Too many coffee
grounds were
placed in the
filter.
REMOVE FILTER
DISCARD GROUNDS.
IF PAPER FILTER,
REPLACE. IF
PERMANENT FILTER,
RINSE. BEGIN BREWING
PROCESS AGAIN.
The carafe was
removed from
the warming
plate for more
than 30 seconds.
TURN OFF AND
UNPLUG THE UNIT.
ALLOW TO COOL.
WIPE UP THE SPILL. DO
NOT SET HOT Carafe
BACK ON THE WET
WARMING PLATE OR IT
MIGHT CRACK.
PROBLEM POSSIBLE CAUSE SOLUTION
THE COFFEE IS
NOT HOT There’s a power outage. WAIT FOR POWER TO BE RESTORED.
Auto SHUT-
OFF has been
activated.
FOR BEST RESULTS,
BREW A FRESH POT OF
COFFEE.
THE COFFEE
TASTES BAD Coffee grounds other than for
an automatic
drip coffeemaker
were used.
USE COFFEE GROUNDS
RECOMMENDED FOR
AUTOMATIC DRIP
COFFEEMAKERS.
The ground
coffee-to-
water ratio was
unbalanced.
USE CORRECT
GROUND COFFEE-TO-
WATER RATIO.
The coffeemaker
needs cleaning. CLEAN COFFEEMAKER AS DESCRIBED IN
“MAINTAINING YOUR
COFFEEMAKER” SECTION.
THE GROUNDS
ARE IN THE
COFFEE
The filter is not
properly seated
in the basket.
SEAT FILTER PROPERLY
WITHIN THE FILTER
BASKET.
The filter
collapsed. REMOVE FILTER AND REPLACE.
Do you still have questions? You can call us toll-free at
the MR. COFFEE
TM
Consumer Service Department,
1-800-MR COFFEE (1-800-672-6333) or you can visit us
at www.mrcoffee.com.

24 25
SERVICE AND MAINTENANCE
Replacement Parts
• Water filtration system and Replacement water
filtration disks can be purchased through your local
retailer, online at www.mrcoffee.com, or by calling
1-800-MR-COFFEE (1-800-672-6333) in the U.S. or
1-800-667-8623 in Canada.
• Carafes – You can usually purchase a replacement
carafe from the store where you purchased
your coffeemaker. If you are unable to find a
replacement, please visit us online at
www.mrcoffee.com, or call 1-800-MR COFFEE
(1-800-672-6333) in the U.S. or 1-800-667-8623
in Canada for information on where you can find a
store that carries replacement carafes.
Repairs
This appliance has no user serviceable parts.
If your coffeemaker requires service, do not return
it to the store where you purchased it. All repairs
and replacements must be made by Sunbeam or an
authorized Sunbeam Service Center. If you live in the
U.S. or Canada, please call us at the following toll-free
telephone numbers to find the location of the nearest
authorized service center:
U.S. 1-800-MR COFFEE (1-800-672-6333)
Canada 1-800-667-8623
You may also visit our website at www.mrcoffee.com for
a list of service centers.
To assist us in serving you, please have the coffeemaker
model number and date of purchase available when
you call. The model number is stamped on the bottom
metal plate of the coffeemaker.
We welcome your questions, comments or suggestions.
In all your communications, please include your
complete name, address and telephone number and a
description of the problem.
Visit our website at www.mrcoffee.com and discover
the secret to brewing the perfect cup of coffee.
You will also find a rich blend of gourmet recipes,
entertaining tips and the latest information on MR.
COFFEE
®
products.

26 27
WARRANTY INFORMATION
1-YEAR LIMITED WARRANTY
Sunbeam Products, Inc. or if in Canada, Sunbeam
Corporation (Canada) Limited doing business as
Jarden Consumer Solutions (collectively “Sunbeam”)
warrants that for a period of one year from the date
of purchase, this product will be free from defects in
material and workmanship. Sunbeam, at its option, will
repair or replace this product or any component of
the product found to be defective during the warranty
period. Replacement will be made with a new or
remanufactured product or component. If the product
is no longer available, replacement may be made with
a similar product of equal or greater value. This is your
exclusive warranty. Do NOT attempt to repair or adjust
any electrical or mechanical functions on this product.
Doing so will void this warranty.
This warranty is valid for the original retail purchaser
from the date of initial retail purchase and is not
transferable. Keep the original sales receipt. Proof of
purchase is required to obtain warranty performance.
Sunbeam dealers, service centers, or retail stores selling
Sunbeam products do not have the right to alter,
modify or any way change the terms and conditions of
this warranty.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent
use or misuse of the product, use on improper voltage
or current, use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than
Sunbeam or an authorized Sunbeam service center.
Further, the warranty does not cover: Acts of God, such
as fire, flood, hurricanes and tornadoes.
What are the limits on Sunbeam’s Liability?
Sunbeam shall not be liable for any incidental or
consequential damages caused by the breach of any
express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any
implied warranty or condition of merchantability or
fitness for a particular purpose is limited in duration to
the duration of the above warranty.
Sunbeam disclaims all other warranties, conditions or
representations, express, implied, statutory or otherwise.
Sunbeam shall not be liable for any damages of any
kind resulting from the purchase, use or misuse of, or
inability to use the product including incidental, special,
consequential or similar damages or loss of profits, or for
any breach of contract, fundamental or otherwise, or for
any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the
exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty
lasts, so the above limitations or exclusion may not apply
to you.
This warranty gives you specific legal rights, and you
may also have other rights that vary from province to
province, state to state or jurisdiction to jurisdiction.

28 29
How to Obtain Warranty Service
In the U.S.A.
If you have any question regarding this warranty or
would like to obtain warranty service, please call
1-800-672-6333 and a convenient service center
address will be provided to you.
In Canada
If you have any question regarding this warranty or
would like to obtain warranty service, please call
1-800-667-8623 and a convenient service center
address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam
Products, Inc. located in Boca Raton, Florida 33431.
In Canada, this warranty is offered by Sunbeam
Corporation (Canada) Limited, located at 20 B Hereford
Street, Brampton, Ontario L6Y 0M1. If you have any
other problem or claim in connection with this product,
please write our Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF
THESE ADDRESSES OR TO THE PLACE OF PURCHASE
MEDIDAS DE SEGURIDAD
IMPORTANTES
A fin de reducir el riesgo de incendio, descarga eléctrica y/o
lesión personal al utilizar aparatos eléctricos siempre se deben
seguir precauciones básicas de seguridad, incluyendo las
siguientes:
1. Lea todas las instrucciones.
2. No toque las superficies calientes. Utilice asas o
perillas.
3. A fin de protegerse contra una descarga eléctrica, no
coloque ni sumerja el cable, los enchufes o el aparato
en agua o ningún otro líquido.
4. Este aparato no está diseñado para ser utilizado por
los niños ni por personas con su capacidad física,
sensorial o mental reducida, o falta de experiencia o
conocimiento. Todo aparato utilizado cerca de los
niños, requiere la supervisión cercana de un adulto.
Los niños deben ser supervisados para asegurar que
no jueguen con el aparato. Mantenga el aparato y su
cable fuera del alcance de los niños.
5. Desenchufe el aparato del tomacorriente cuando éste
o el reloj digital (si es proporcionado) no esté en uso
y antes de limpiarlo. Permita que el aparato se enfríe
antes instalarle o retirarle piezas y antes de limpiarlo.
6. No opere ningún aparato que tenga un cable o
enchufe dañado o después de presentar un fallo en
su funcionamiento o si ha sido dañado de manera
alguna. Devuelva el aparato a un centro de servicio
autorizado para su revisión, reparación o ajuste. No
intente reemplazar o cortar un cable dañado.
7. El uso de accesorios no recomendados por el

30 31
fabricante del aparato podría ocasionar incendio,
descarga eléctrica o lesiones personales.
8. No utilice el aparato a la intemperie.
9. No permita que el cable cuelgue del borde de la mesa
o del mostrador ni que toque superficies calientes.
10. No coloque el aparato sobre o cerca de una hornilla
caliente de gas o eléctrica ni dentro de un horno
caliente.
11. Siempre conecte primero el enchufe al aparato
y luego enchufe el cable al tomacorriente (para
aparatos con cables separables). Para desconectar,
gire todo control a la posición de apagado y luego
retire el enchufe del tomacorriente.
12. No utilice el aparato para otro fin que no sea para el
que ha sido diseñado.
13. Todas las tapas deben estar cerradas durante el uso.
14. Si la tapa es retirada o la puerta de la cesta de
preparación se abre durante o inmediatamente
después que termine el ciclo de preparación, esto
podría ocasionar quemaduras. El contenido puede
estar caliente. Permita que se enfríe antes de abrir la
tapa.
Para aparatos con jarras de vidrio:
15. La jarra está diseñada para utilizarse con este aparato.
Nunca debe ser utilizada sobre una estufa.
16. No coloque una jarra caliente sobre una superficie
mojada ni fría.
17. Evite los cambios de temperatura bruscos, tales como
enjuagar, lavar, llenar o sumergir una jarra caliente en
líquidos fríos.
18. No utilice una jarra rajada o astillada, o que tenga el
asa floja o debilitada.
19. No limpie la jarra con limpiadores, estropajos de
lana de acero ni ningún otro material abrasivo.
Para aparatos con paneles de servicio:
20. ADVERTENCIA: PARA REDUCIR EL RIESGO DE
INCENDIO O DESCARGA ELÉCTRICA, NO RETIRE ESTA
TAPA. NO TIENE PIEZAS EN EL INTERIOR QUE DEBAN
SER REPARADAS POR EL USUARIO. CUALQUIER
REPARACIÓN SOLO DEBE SER REALIZADA POR
PERSONAL DE SERVICIO AUTORIZADO.
CONSERVE ESTAS
INSTRUCCIONES
SOLO PARA USO DOMÉSTICO
Este electrodoméstico tiene
un enchufe polarizado (un
contacto es más ancho que el
otro). Para reducir el riesgo de descargas eléctricas,
como una función de seguridad, este enchufe
está diseñado para encajar en un tomacorriente
polarizado solo de una forma. Si el enchufe no
se inserta completamente en el tomacorriente,
invierta el enchufe. Si aún no encaja, consulte a
un electricista calificado. No intente ignorar esta
medida de seguridad ni modificar el enchufe en
forma alguna. Si el enchufe se inserta holgadamente
en el tomacorriente de corriente alterna o si
el tomacorriente de corriente alterna se siente
caliente, no use ese tomacorriente.
ENCHUFE POLARIZADO

32 33
USO Y CUIDADO DE LA JARRA
Siga las instrucciones a continuación para disminuir o eliminar
el riesgo de quebrar la jarra de vidrio:
• Descarte la jarra de inmediato si en alguna ocasión hierve
hasta evaporarse todo su contenido.
• Proteja la jarra contra golpes secos, rasguños o maltrato.
TABLA DE CONTENIDO
Advertencias de Seguridad..................................................29
Introducción............................................................................31
Uso y Cuidado de la Jarra......................................................31
Instrucciones Especiales Sobre el Cordel Eléctrico............31
Tabla de Continedo...............................................................33
Diagrama de las Partes.........................................................34
Características y Beneficios de la Cafetera........................36
Limpie su Cafatera Antes de Utilizarla por Primera Vez........37
Programando la Hora del Reloj y la Función
de Colar Luego........................................................................38
PreparándoseparaUtilizarlaCafetera..................................39
• Tabla de Medidas de Café Sugeridas
• Añadiendo agua y Café Molido
• Sistema de Filtración de Agua (no incluido)
Colando Café Ahora...............................................................43
Colando Café Luego (Colar Luego)............................45
Limpiando y Dándole Mantenimiento a su Cafetera..........47
Resolviendo Problemas con su Cafetera Mr. Coffee®.........50
Servicio y Mantenimiento.......................................................54
Información Sobre la Garantía.............................................56
toma el cuidado debido en su uso. Si se utiliza un cable de
alimentación separable largo o un cable de extensión:
a. La clasificación eléctrica marcada del cable de
alimentación separable o cable de extensión debe
ser, como mínimo, igual a la clasificación eléctrica del
aparato;
b. Si el aparato es del tipo de conexión a tierra, el cable
de extensión debe ser un cable de tres alambres de
conexión a tierra; y
c. El cable más largo debe ser acomodado de manera que
no cuelgue del mostrador o de la mesa para evitar que
un niño tire del mismo o que alguien se tropiece sin
darse cuenta.
No hale, tuerza ni maltrate de manera alguna el cable de
alimentación.
AVISOS DEL PRODUCTO
1. Coloque el aparato sobre una superficie dura, plana y
nivelada para evitar interrupciones en el flujo de aire por
debajo de la cafetera.
2. Solo para jarras de vidrio: Descarte la jarra de inmediato
si en alguna ocasión hierve hasta evaporarse su
contenido.
3. Solo para jarras de vidrio: Proteja la jarra contra golpes
secos, rasguños o maltrato.
4. No opere el aparato con un tanque de agua vacío.
5. Mantenga el área encima del aparato despejada durante
el uso, ya que vapor caliente saldrá del aparato.
INSTRUCCIONES PARA EL CABLE DE
ALIMENTACIÓN:
Un cable de alimentación corto (o cable de alimentación
separable) puede ser provisto para reducir los riesgos
de enredarse o tropezar con un cable más largo. Existen
cables de alimentación separables más largos o cables de
extensión disponibles y estos pueden ser utilizados si se

3534
1. Tapa de la
Canasta del Filtro
2. Cubierta de la
Regadera
3. Tanque de Agua
4. Ventanilla del
Nivel de Agua
5. Detenga y
Sírvase (Pause ‘n
Serve)
6. Plato Calefactor
7. Jarra
8. Canasta
Removible del
Filtro
9. Cuchara
Medidora de
Café
DIAGRAMA DE LAS PARTES
a. Pantalla del Reloj/
Pantalla del Contador
de Tiempo de Frescura
b. Botón de Minutos
c. Contador del Tiempo
de Frescura
d. Selector de Intensidad
del Colado (Regular/
Fuerte)
e. Botón de Intensidad
del Colado
f. Boton de Select/Off
(Seleccionar/Apagar)
g. Luz de Colar Ahora
h. Indicador de la
Función de Colar
Luego
i. Botón para Fijar la
Función de Colar
Luego
j. Botón de la Hora
PANEL DE CONTROLES
Otros artículos para su cafetera
(no incuido en todos los modelos)
Sistema de
Filtración de Agua Filtro de Café Reusable Marca
Mr. Coffee
®
a
b
h
f
i
j
e
d
dc
g
1
2
3
4
5
6
79
8
Cuchara Medidora de Café

37
CARACTERÍSTICAS Y BENEFICIOS DE LA CAFETERA
Su nueva Cafetera MR. COFFEE
®
cuenta con las
siguientes características:
• Capacidad de preparación – 12 tazas – Serie con
jarra de vidrio
• Canasta Removible del Filtro – La canasta del filtro se
saca para un limpiado y llenado fácil y rápido.
• Pause ‘n Serve (Detenga y Sírvase) – ¿No puede
esperar a que el café termine de colarse? Pause
‘n Serve le otorga hasta 30 segundos para servirse
una taza de café mientras la cafetera aún está
colando. Saque la jarra con cuidado y Pause ‘n
Serve se activará automáticamente, deteniendo
temporalmente el flujo del café hacia la jarra.
• Ventanilla del Nivel de Agua – Muestra la cantidad
de agua en el tanque para un llenado preciso.
• Plato Calefactor Antiadherente – (no incluido con
modelos térmicos) Esta característica le permite
mantener su café caliente luego de colado. El
atributo antiadherente evita que la jarra se adhiera
a la superficie del plato calefactor.
• Selector de Intensidad del Colado – Ajusta el período
de colado para preparar un café más cargado.
• Filtracion de agua capaz – ¡Un café de sabor
óptimo comienza con un agua óptima! Utilizando el
Mr. Coffee
®
filtro de carbono del agua en la cafetera
Mr. Coffee
®
durante el proceso de preparación de
café ayuda a eliminar hasta 97% del cloro del agua
y mejora el sabor de su café. Si quieres comprar un
filtro de agua por favor visitar www.mrcoffee.com.
• Almacenaje del Cordel – Almacena el sobrante
del cordel eléctrico de manera segura para que su
mostrador se vea nítido.
36
• Apagado Automático de 2 Horas – Mantiene su
café caliente durante dos horas, y luego se apaga
automáticamente.
• Controles Programables:
Reloj – El reloj sirve como un práctico reloj de
cocina y le permite programar la función Brew Later
(colar luego) a la hora que desería que la cafetera
comience a preparar su café y funciona como
Contador de Tiempo de Frescura.
Función de Contador de Tiempo de Frescura – Le
permite saber por cuanto tiempo su café ha estado
esperando por usted.
Colar Luego – ¿Le gustaría despertarse y disfrutar
de una jarra de café acabada de colar? La función
Brew Later (colar luego) le permite programar de
antemano la hora que desearía que la cafetera
comience a colar su café automáticamente, hasta
24 horas por adelantado.
ADVERTENCIA: Si usted ha seleccionado
cualquiera de las funciones de realizar
operaciones, la cafetera efectuará la última
operación seleccionada si se restaura el
servicio eléctrico durante los primeros diez
segundos luego de un apagón eléctrico.
LIMPIE SU CAFETERA ANTES DE UTILIZARLA POR
PRIMERA VEZ
Asegúrese de que su primera taza de café sea tan
buena como sea posible limpiando su Cafetera MR.
COFFEE
®
antes de utilizarla por primera vez. Solo tiene
que seguir estos pasos sencillos:
1. Lave la jarra, la tapa de la jarra y la canasta del
filtro en una mezcla de detergente suave y agua.

Para Programar la Hora de Demora de la
Función de Colar Luego:
Cuando la pantalla esté en el modo del
reloj, simplemente presione el botón
Set Brew Later (programar la función
de colar luego) (Figura 3) y, cuando la
luz de la función de Colar a Luego esté
parpadeando, ajuste el tiempo de colado,
presionando los botones HOUR (hora) y
MINUTE (minutos). El indicador AM o PM se
iluminará en el lado izquierdo de la pantalla
del reloj. (Figura 4)
En solo unos segundos, la pantalla cambiará
a la hora actual. ¡La hora de la función de
Colar Luego ya está programada!
NOTA: Para activar el ciclo de COLAR LUEGO consulte
la sección “Colando Café Luego”. Para verificar la
hora programada, presione el botón SET BREW LATER
(programar la función de colar luego). La pantalla
mostrará la hora que usted ha programado para colar
el café. Si presiona el botón SET BREW (programar el
colado) de nuevo o espera unos segundos, la pantalla
regresará a la hora actual.
PREPARÁNDOSE PARA UTILIZAR LA CAFETERA
Seleccionando y Midiendo el Café Molido
Para los mejores resultados, utilice la cuchara medidora
de café incluida para medir el café molido. Asegúrese
de utilizar un molido de café medio para lograr un
colado perfecto.
3938
Enjuague bien cada una (favor referirse al diagrama
de las partes que antecede).
2. Ponga todas las partes de vuelta y cierre la tapa.
Luego, sin poner el café ni el filtro del café,
complete un filtro de colado según se describe en
el Paso 1 de “Colando Café Ahora”.
3. Cuando se complete el colado, apague su cafetera,
descarte el agua en la jarra y enjuague la jarra, la
tapa de la jarra y la canasta del filtro.
Su cafetera ya está lista para utilizarse. ¡Disfrútela!
PROGRAMANDO LA HORA DEL RELOJ Y
LA FUNCIÓN DE COLAR LUEGO
Para Programar la Hora del Reloj:
1. Enchufe el cordel eléctrico en un
tomacorriente estándar. El reloj
parpadeará en el panel de controles
para indicar que la hora aún no ha sido
programada.
2. Oprima y mantenga oprimidos los
botones de HOUR (HORA) y MINUTE
(MINUTO) hasta que el reloj marque la
hora actual. Los indicadores de AM o
PM se encenderán en la parte de fondo
de la pantalla (Figuras 1 y 2).
¡El reloj ya ha sido programado!
ADVERTENCIA: El oprimir cualquier botón antes de
programar el reloj hará que el reloj comience a marcar
la hora a partir de las 12:00 a.m. Usted debe programar
el reloj si desea usar la característica de Demora del
Colado.
Figura 1
Figura 2
Figura 3
Figura 4