Mr. steam Ct6e Instruction manual

.steam

Feel Good Inc.

Clu Therapy Steam ath Generator Systems

Installation, Operation & Maintenance Manual Models: CT6E, CT9E, CT12E, CT15E

Installation, Operation & Maintenance Manual

Club Therapy®Steambath Generator Systems

INSTALLATION, OPERATION & MAINTENANCE MANUAL

Table of Contents

Read Me First! & Warning Placard .....................................1

Select Your Clu Therapy Model .......................................2

Specification Chart .............................................................2

Before Installing .................................................................3

Steam Room Guidelines.....................................................3

Locating the Steam Generator Unit ...................................4

Typical Installation ..............................................................4

Installation: Plum ing, Water Supply, Drain, Steam Outlet

Safety Valve, Drip Pan, AromaSteam ..............5

Water Quality Information..................................................5

Steam Head Installation .....................................................6

Generator Dimensions .......................................................7

Electrical Specifications & Field Power Wiring ..................8

Wiring Diagrams.................................................................9

Initial Start-Up & Checkout, Maintenance,

Trou leshooting and Operation ...................................10

System Status Codes, Liquid Level Control Board ..........11

AutoFlush®System ...........................................................12

Drip Pan, Express Steam®................................................13

Replacement Parts List.....................................................13

Replacement Parts Diagram.............................................14

Controls

Before Installing, Control Rough-In..................................15

CT SteamStop ..................................................................16

Care Tips for Controls and Steamhead............................17

General

Warranty ...........................................................................17

M A D E I N U S A

PUR

100426

REV

2.15

mr.steam®Sussman-Automatic Corporation®[email protected] www.mrsteam.com

43-20 34th Street, Long Island City, NY 11101 TEL: 1 800 76 STEAM FAX: 718 472 3256

9410 S. La Cienega Blvd. Inglewood CA 90301 TEL: 1 800 72 STEAM FAX: 310 216 2944

READ ME FIRST!

IMPORTANT NOTE:

As you follow these instructions, you will

notice warning and caution sym ols. This

locked information is important for the

safe and efficient installation and opera-

tion of this generator. These are types of

potential hazards that may occur during

this installation and operation:

states a hazard may cause serious injury

or death if precautions are not followed.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

IMPORTANT NOTE:

This highlights

information that is especially relevant to a

pro lem-free installation.

All information in these instructions is

ased on the latest product information

availa le at the time of pu lication.

Sussman-Automatic Corporation reserves

the right to make changes at any time

without notice.

When installing and using this electrical equipment, asic safety precautions

should always e followed, including the following:

IMPORTANT SAFETY INSTRUCTIONS

1. READ AND FOLLOW ALL INSTRUCTIONS

2. Do not permit children under the age of 16

to use this steam ath.

To reduce the risk of injury:

A. The wet surfaces of steam enclosures may e slippery. Use care when

entering or leaving.

B. The steam head is hot. Do not touch the steam head and avoid the

steam near the steam head.

C. Prolonged use of the steam system can raise excessively the internal

human ody temperature and impair the ody’s a ility to regulate its

internal temperature (hyperthermia). Limit your use of steam to 10-15

minutes until you are certain of your ody’s reaction.

D. Excessive temperatures have a high potential for causing fetal damage

during the early months of pregnancy. Pregnancy or possi ly pregnant

women should consult a physician regarding correct exposure.

E. O ese persons and persons with a history of heart disease, low or high

lood pressure, circulatory system pro lems, or dia etes should consult

a physician efore using a steam ath.

F. Persons using medication should consult a physician efore using a

steam ath since some medication may induce drowsiness while other

medications may affect heart rate, lood pressure and circulation.

A warning placard has een provided in the Information

envelope. This placard is an essential part of providing

a safe environment for steam room users. This placard

must e mounted to the wall of the shower or steam

enclosure, at a point visi le to all users. Failure to

mount this placard may result in serious injury or death.

SAVE THESE INSTRUCTIONS

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

WARNING

CAUTION

HYPERTHERMIA occurs when the internal temperature

of the ody reaches a level several degrees a ove the

normal ody temperature of 98.6° F. The symptoms of

hyperthermia include an increase in the internal tem-

perature of the ody, dizziness, lethargy, drowsiness,

and fainting. The effects of hyperthermia include:

a) Failure to perceive heat;

) Failure to recognize the need to exit the steam ath;

c) Unawareness of impending risk;

d) Fetal damage in pregnant women;

e) Physical ina ility to exit the steam ath

and

f) Unconsciousness.

The use of alcohol, drugs, or medica-

tion can greatly increase the risk of hyperthermia.

WARNING

not actual size

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

In considering a purchase of this steam-

ath system, please note that if users are pregnant,

have a coronary condition, are in poor health, are eing

treated for any other medical condition, or are using

medication or drugs, Mr.Steam recommends that you

o tain the approval of their physician efore use.

For information a out this product and safety issues,

please call us at 1-800-76-STEAM or log onto

www.mrsteam.com

IMPORTANT NOTES:

•

The guidelines for selecting the steam ath generator

is a recommendation only. Because of varia les in

construction, these sizing instructions and specifica-

tions should e considered as guidelines only.

Mr.Steam®will review the model selected provided we

receive complete information, including working draw-

ings, specifications, and pertinent electrical and con-

struction details. Otherwise, the manufacturer dis-

claims responsi ility for the sizing of a model selected.

• For steam rooms constructed of acrylic or synthetic

materials, select next lower-rated CT model.

• The total adjusted room volume allows for up to 60

feet of insulated steam line from the CT generator to

the steam room. If the 60 feet line is exceeded

consult with factory. When locating the steam genera-

tor consideration of the control and external tempera-

ture pro e must e taken into account. The maximum

length for a control ca le is 60 feet. The maximum

length of the MSTS (used with iTempo) is 60 feet.

MSTS connects to the steam generator. The maxi-

mum length of the iMSTS (used with iSteam) is 25

feet. iMSTS connects to the iSteam control.

Steam Generators Specification Chart

Amps (for Total A j Wire Water Usage Shipping

Mo el No. KW 240v/1PH)† Room Vol. Size‡ gallons†† Dimensions* Wt. (lbs)**

CT6E 6 25 150 8 0.80 17"L x 18½"H x 77⁄8"D 40

CT9E 9 38 360 8 1.2 17"L x 18½"H x 77⁄8"D 40

CT12E 12 50 575 6 1.6 17"L x 18½"H x 77⁄8"D 40

CT15E 15 63 675 4 2.0 17"L x 18½"H x 77⁄8"D 40

IMPORTANT: A C1 suffix to Mo el No. for 240V/1Ph; A B1 suffix to Mo el

No. for 208V/1Ph.

IMPORTANT: All CT MS Mo els are cUL us Liste an CE; approve .

NOTES:

All CT Generators availa le in 240v/1PH, 208v/1PH and other voltages/phases.

† Amps are for 240/1PH rated units.

‡Wire size (AWG) ased on minimum 90˚C rated THHN copper conductors.

Refer to the National Electrical Code for other types of conductors.

*Dimensions are for generator only, without

AutoFlush®or plum ing features.

**Shipping weight and pricing are for gener-

ator only, without control or steamhead.

†† Water usage ased on 20 minutes of

operation.

Materials of construction, room size and special design features such as

large glass areas, all affect the steam generator model selection.

Measure length, width & height in feet of the steam/shower or tu /shower

Multiply the Length ____ x Width____ x Height _____ =

2. Construction Materials:

For natural stones: natural mar le, Add 110%

stone, shale, glass lock or concrete

For ceramic or porcelain tile on Add 40%

cement oard or mortar ed

3. Ceiling Height: For each foot a ove 8 feetAdd 15%

4. Add all figures a ove to o tain

the Total Room Volume required

ROOM

VOLUME

TOTAL ADJUSTED

ROOM VOLUME

Select Your Club Therapy Mo el

Compare your TOTAL ADJUSTED ROOM VOLUME to the Specification Chart

elow and select the appropriate model.

Visit www.mrsteam.com to size your generator automatically.

WARNING

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

If acrylic, fi erglass or other non-heat resistant materials are

used as part of the steam room enclosure. Consult with the material manu-

facture and see pg. 6, “Installing the Steamhead" for additional details.

IMPORTANT NOTES:

This document contains important safety, operation and maintenance infor-

mation. Leave this document with the clu /spa management.

Do not discard this document.

The following general information should e used in conjunction with con-

sultations with an architect, designer and contractor in determining factors

necessary in providing a suita le and safe steam room.

Mr.Steam CT steam generators are intended to e operated with Mr.Steam’s

iTempo/Plus™, iSteam®and CT SteamStop®only, and are to e installed

strictly in accordance with the specific instructions contained in this manual

and as supplied in the manuals provided with the

controls or accessories.

Never use damaged equipment, doing so

may result in an inoperative or hazardous installation.

Discontinue use of the steam generator and control if the

steam generator or control are damaged or otherwise not func-

tioning properly. Doing so may result in an inoperative or haz-

ardous installation

ELECTRICAL SHOCK HAZARD. Mr.Steam steam generators are

connected to 240V line voltage and contain live electrical com-

ponents. All installation and service to e performed y quali-

fied and licensed electricians and plum ers only. Installation or

service y unqualified persons or failure to use Mr.Steam parts

may result in property damage or in a hazardous condition.

Do Not alter or modify any Mr.Steam prod-

uct. Doing so may result in an inopera le or hazardous

installation and will void the warranty

The warning placard is located in the documenta-

tion envelope. This placard is an essential part of providing a safe

environment for steam room users. This placard must e mounted

to the wall of the shower or steam enclosure, at a point visi le to

all users. Failure to mount this placard may result in serious injury

or death. For a replacement placard contact Mr. Steam customer

service at 1-800-76-STEAM or [email protected]

Before Installing

Carefully inspect the CT steam generator and packaging for

shipping damage. In the event of shipping damage, please

contact the carrier for claim information. Our customer

service department can assist you with any missing or

damaged parts.

Read these instructions efore installation or service.

Although this CT steam generator has een fully qualified

for shipment y Mr.Steam, the following must e reviewed

for proper, safe and enjoya le steam athing:

1. Verify that the model and accessories specifications are

correct for the incoming line voltage.

2. Insure steam ath generator has een correctly sized for

Steam Room Gui elines

1. Steam room must e completely enclosed, with full

walls, door, floor and ceiling.

2. It is recommended that a gasketed door is used for

steam containment.

3. If tile-type or other smooth surfaced flooring is used

provide suita le anti-skid strips or equivalent, to

prevent a slipping hazard.

4. Check the suita ility of any materials with the

manufacturer. Walls and ceilings must e constructed

of water-resistant, non-corrosive surface, such as tile,

mar le, molded acrylic, or other non-porous material.

5. The ceiling should e sloped to prevent dripping of

condensate.

6. Provide a floor drain.

7. No heating, venting or air conditioning devices

should e installed inside the steam room.

8. Steam room tile construction information is availa le

from the Tile Council of America, Inc. y purchasing

the TCA Hand ook for Ceramic Tile Installation.

Tel. (864) 646-8453 or www.tileusa.com.

9. Windows that are part of the steam room should e

dou le paned and tempered safety glass.

10. Limit steam room ceiling height to 8 feet. Exceeding

8 feet may require a higher-rated steam generator.

the steam ath room. Pay particular attention to room vol-

ume and construction. If any questions, please refer to

Mr.Steam sizing and selection guide on page 2.

3. Mar le or glass walls or ceilings “enlarge” the room’s size

requiring a generator larger than one ased only on the

room’s cu ic foot (L x H x W) volume.

4. The physical size of the unit, clearance for plum ing

servicing, and its distance from the steam room must all

e considered efore final installation.

5. Consider any controls and accessories efore initiating

installation. Read the Installation and Operation

Manual of all controls and accessories availa le at

www.mrsteam.com/products/technical-downloads.html

WARNING

CAUTION

Not Actual Size

Locating the Steam Generator Unit

IMPORTANT NOTE:

The control ca les should e run in dedicated 1" conduit to facilitate installation and service

Select a location as near as practical to the steam room. Typical locations include: closet, vanity ca inet, heated attic or asement.

NOTE:

The maximum length of the MSTS (used with iTempo) is 60 feet. MSTS connects to the steam generator. The maximum length of the

iMSTS (used with iSteam) is 25 feet. iMSTS connects to the iSteam control.

(Items 1-7)

1. DO NOT install steam ath generator or plum ing lines in

unheated attic or any locations where water could freeze.

2. DO NOT install steam ath generator inside steam room.

3. DO NOT install steam ath generator outdoors or wherever

environmental conditions may affect the safety and/or

performance of the generator.

4. DO NOT install steam ath generator near flamma le or corrosive

materials or chemicals such as gasoline, paint thinners, or the like.

Installation in areas having high concentrations of chlorine (such

as pool equipment room) must e avoided.

5. Install steam ath generator on a solid and level surface. Keyhole

slots are provided for wall mounting. Insure the steam generator

is properly secured and level when mounting with keyhole slots.

6. Install steam ath generator in an upright position only.

Steam line, safety valve, drain valve, plum ing and steamheads

ecome hot during operation and remain hot after shutdown

for a period of time. Provide appropriate protection, including

insulating plum ing lines. Avoid plum ing runs and steamhead

locations that can come in contact with athers.

NOTE: FOR ILLUSTRATIVE PURPOSES ONLY

Some components may e omitted or altered

for clarity. Do not use for wiring, repair or other

purposes not related to component identification

Provide unions as required to facilitate

installation and disconnect of piping

Steam

Generator

Field installed

power supply

Field installed

steam supply pipe

Drain Valve should be closed

when AutoFlush is not installed

Control cables run in 1”conduit

(located behind the wall)

Steam Head (shown with optional acrylic shield)

See page 6 for Steam Head Installation information

Remote Sensor

see page 17

CT SteamStop®Control

See page 18 for

installation information.

iTempo/Plus®or iSteam

Control- See page 17

Field installed

water supply line

IMPORTANT:

Locate the remote

sensor in a location representative of

the desired steambathing temperatures.

Do not locate the control above or near

the steam head or direct steam emissions.

Typical Mr.Steam®Installation

IMPORTANT:

(Items 8-11)

8. Install anti-water hammer device as necessary.

Provide a minimum of 12 inches at oth ends and

top of the steam generator or as required for servic-

ing. See page 7.

10. Provide unions as required to facilitate installation

and disconnection of piping.

11. The controls should e placed in a location

only accessi le y the facility’s staff. The CT

SteamStop®and remote sensor are required to

e installed inside the steamroom.

NOTE:

Mr.Steam Generators and controls are CE

and UL listed.

The CT series of steam generators are

for commercial use only.

When installing the optional AromaSteam,

install a downward facing 90-degree T in

the steam supply line. See the AromaSteam

Installation Manual for complete information.

WARNING

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Installation

Plumbing

All plum ing shall e performed y a qualified licensed plum er

and in accordance with applica le National and local codes.

• Use unions on all pipe connections.

• Use only rass piping or copper tu ing as permitted y codes.

• Do not use lack, galvanized, PVC, or PEX pipe.

Water Supply (3⁄8"N P T )

1. Connect to cold water line.

2. Provide a shut off valve in the water supply line upstream of the

steam ath generator.

3. Do not overheat inlet solenoid valve with solder connections.

Overheating will damage parts.

4. Flush inlet water line thoroughly efore making connection to

unit.

5. Strainer recommended upstream of feed water connection.

6. For est performance water pressure should e 15 to 20 psig.

Reduce pressure as required.

7. Provide anti-water hammer device as required.

8. Install an approved ackflow preventer as required y local

codes.

Drain

(1" N P T )

The rain from the generator shoul not share an un ersink

trap, unless the generator is mounte higher than the sink.

NOTE: A drain valve is provided to facilitate servicing.

Provide a drain line connection from steam ath generator drain

valve according to National and local Codes. Check local plum ing

code for receptor, trap and vent requirements. Do not connect

Drain line and Safety Valve line together. Unit rains by gravity.

Do NOT connect the drain valve to the steam line.

Safety Valve (3⁄4"

N P T

)

Where permitted y local codes, provide an outlet plum ing con-

nection for safety valve.

To insure proper and automatic safety valve

operation: DO NOT connect a shut off valve or a plug at

safety valve outlet. DO NOT connect a shut off valve or any

construction in steam supply pipe.

Steam Outlet (1⁄2"N P T )

1. Do not install any valve in steam line. Flow of steam must

e uno structed.

2. Use 1⁄2inch rass pipe or copper tu ing from unit to

steam head as permitted y codes.

3. Insulate steam line using pipe insulation rated 212° F

or higher.

4. Pitch steam line 1⁄4" per foot towards steam head or steam

generator to avoid valleys and trapping of condensate.

IMPORTANT NOTES:

• Running the steam line down and then up will create a

steam trap locking the flow of steam.

•

A 1.5" hole in the steam room is required to mount the

steamhead.

Drip Pan

Mr. Steam strongly recommends the use of a drip pan in

the unlikely event of a plum ing leak. Check local plum -

ing codes for receptor, trap and vent requirements. Drip

pans drain y gravity. The drip pan is equipped with an

integral 3⁄4" fitting. See page 14 for additional drip pan

installation information.

AromaSteam

If the optional AromaSteam Electronic Oil Delivery System

(PN:MS AROMA) is to e installed, a 90 degree Tplum ing fitting

must e installed at a designated location on the steam outlet

line. See the Mr.Steam AromaSteam Operation and Instruction

Manual for installation information efore the steam line is

installed at www.mrsteam.com technical downloads.

Water Quality Information

For optimum results, the water supply should e tested prior

to installation. If the mineral content exceeds the following

recommended limits, various external treatment processes are

recommended to correct the pro lem.

NOTE: An analysis of the on-site water must e made y a

recognized and relia le water treatment company to ascertain

the existing condition and treatment required.

Poor water quality can affect efficiency or result in steam gen-

erator damage. Water contains impurities in solution and sus-

pension. These impurities concentrate in the generator. The

concentration of these impurities increases as more feedwater

is introduced into the generator and steam is produced. If the

suspended solids are allowed to concentrate eyond certain

limits, a deposit or “scale” will form on the generator internal

surfaces. This deposit can interfere with the proper generator

operation and cause generator failure. The concentration of

these impurities is generally controlled y the water quality

and y periodic draining of the generator.

RECOMMENDED FEEDWATER QUALITY

Hardness, ppm 8 – 85 (~0.5 – 5 gpg)

P-Alkalinity, ppm 85 – 410 (~5 – 24 gpg)

T. Alkalinity, ppm 200 – 500 (~7 – 0 gpg)

pH (strength of alkalinity) 8.0 – 11.4

The CT AutoFlush®System feature automatically drains the

Mr.Steam®CT generator following each use. A time delay

allows the water to cool down (a out two hours) efore it

drains y gravity for a safe and gentle operation.

WARNING

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Steam

Supply Pipe

End of pipe to

be recessed 1/8"

1/8" minimum clearance

required for Acrylic Shield.

Apply with silicone

or equal sealant

as required for

moisture seal.

Use Teflon®or

equal sealant on

pipe threads

NOTE: A 1

1⁄2

" clearance hole around the steam pipe is

needed to mount the steamhead.

STEP 1

Locate steam head 6-12 inches a ove floor, except for:

1. Tu /shower enclosures, install 6 inches a ove tu top edge.

2. Consult with supplier of acrylic, fi erglass and other non-heat

resistant enclosures for recommended steamhead location.

3. Use Acrylic Shield MS 103412. See instructions provided with

steam shield.

STEP 2

Install steamhead with the oil well facing up as shown.

Hand tightening is sufficient when teflon or equal pipe thread

sealing compound is used.

STEP 3

Secure a ronze drop ear fitting to a header and run a

1⁄2

" cop-

per steam line from the steam generator to the drop ear

fitting. Install a temporary nipple (6" or longer) in the drop ear fit-

ting to locate the steamhead after the wall is finished.

STEP 4

After the wall has een finished, mark on the nipple where the

surface of the wall is. Remove the nipple and measure the por-

tion that was in the wall (the end to your mark). Su tract 1⁄8" from

that dimension and select a rass nipple of that length to finish

the installation.

STEP 5

Wrap teflon tape around the threads of the new nipple and screw

the nipple into the steamhead. Do not use wrenches or tools which

would damage the steamhead's finish.

Wrap teflon tape around the threads of the nipple and screw the

nipple and steamhead assem ly you just made into the drop ear fit-

ting in the wall. The steamhead should e flush with the wall and

the well must e facing up.

__________________________________________________________

IMPORTANT NOTE:

•Do not disassem le steamhead. Mr.Steam’s steamhead is

shipped fully assem led and requires no additional assem ly.

• To preserve steam head finish, do not use wrenches or other

tools to tighten. DO NOT use a rasive cleansers or chemicals.

Use only water with mild soap and a non-a rasive sponge.

Because the steam head and direct steam emissions are very hot,

locate the steam head where incidental contact y ather with

the steam head or direct steam emission cannot occur.

Oil Well

STEP 3

STEP 4

STEP 5

Installing the AromaSteam Steamhea (1⁄2" NPT)

Steamhead

(shown with acrylic shield)

Locating ipple

Drop Ear

Fitting

CAUTION

All drawings are for illustrative purposes only

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

17"

(432)

3/8

(60)

23/8"

(60)

71/4"

(184)

121/2"

(310)

13/4"

(45)

183/4"

(466)

4"(102)

6"(152)

97/8"

(251)

13/8"

(35)

63/8"

(162)

77/8"(200)

12”(305)

for servicing

WATER INLET 3/8” NPT

STEAM OUTLET 1/2” NPT

SAFETY VALVE 3/4” NPT

MANUAL DRAIN VALVE 1” NPT

AUTOFLUSH VALVE 1” NPT

NOTES

1. M= Optional AutoFlush

2. All units in inches (MM)

Water Inlet

Steam Outlet

Safety Valve

AutoFlush

Manual

Drain Valve

Side View

Showing Element

Access Panel

Generator Dimensions

IMPORTANT NOTES:

• Provide a minimum of 12 inches at oth ends and top

of the steam generator or as required for servicing.

Alternately, provide unions as required to facilitate

installation and disconnection of the steam generator.

• The minimum clearance from com usti le surfaces is

zero all around.

TO AVOID EQUIPMENT DAMAGE DO NOT CONNECT

POWER SUPPLY DIRECTLY TO ELEMENTS !!!

All drawings are for illustrative purposes only

Water Inlet

Control &

Accessory

Connections

Steam Outlet

Safety Valve

Manual

Drain Valve

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Transformer

Liquid Level

Control Board

Water Feed

Solenoid

Water Feed

Thermostat

Liquid Level Probe

Power Block

Power Supply

Knock-Out

Contactor

Steam Outlet

Fuses

AutoFlush Plug and

Play Connector

(see page 13)

Transformer

Liquid Level

Control Board

Water Feed

Solenoid

Water Feed

AutoFlush Plug and

Play Connector

(see page 13)

Thermostat

Liquid Level Probe

Power Supply

Knock-Out

Contactor

Steam Outlet

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Fiel Power Wiring

1. TO AVOID EQUIPMENT DAMAGE DO

NOT CONNECT POWER SUPPLY

DIRECTLY TO ELEMENTS!!!

2. L1, L2, Ground to e field wired

Mo els CT6E – CT9E

(single phase wiring shown)

Mo els CT12E & 15E

(single phase wiring shown)

Electrical

All electrical wiring to e installed y a qualified licensed elec-

trician in accordance with National Electrical Code and local

electrical code.

Power Wiring-

See “Field Power Wiring” Diagrams ( elow)

1. Check power voltage. Use 240V rated unit when supply is

greater than 208V. Use 208V rated unit for 208V power.

2. Use minimum 90˚ C/300V rated insulated copper conductors

only, sized in accordance with National Electrical Code and

local electrical code for the current in Ampere Chart. If

allowed y codes, NM ca le may require a larger wire size

than as listed on the chart.

3. Connect suita ly sized equipment grounding wire to ground

terminal provided.

4. Install a separate circuit reaker etween supply and unit.

Provide a power supply disconnect within sight of the steam

generator or one that is capa le of eing locked in the open

position.

5. For single phase units, use two-wire supply source and equip-

ment grounding wire. Neutral (white) wire is not required.

CHART

___________________________________________________________________________

Model Max Room KW Volts Wire Size Wire Size

o. Vol (Cu. Ft.*) 1 PH

†

Phase Amps (AWG) for 40˚C (AWG) for 45˚C

Ambient Ambient

___________________________________________________________________________

208 1 29 88

CT6E 150 6.0 3 17 10 10

240 1 25 88

314 12 12

___________________________________________________________________________

208 1 44 8 6

CT9E 360 9.0 3 25 88

240 1 38 88

3 22 10 10

___________________________________________________________________________

208 1 58 64

CT12E 575 12.0 3 34 88

240 1 50 66

3 29 88

___________________________________________________________________________

208 1 73 43

CT15E 675 15.0 3 42 86

240 1 63 44

3 36 88

____________________________________________________________

*See page 2 for room sizing.

†All specifications shown are for 208V and 240V. Consult factory for

other voltage specifications.

Provi e a power supply isconnect within sight of the steam

generator or one that is capable of being locke in the open position as permitte by co e.

WARNING

NOTE: FOR ILLUSTRATIVE

PURPOSES ONLY

Some components may e omitted

or altered for clarity. Do not use for

wiring, repair or other purposes not

related to component identification.

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

CONTACTOR

To Probe

HEATING ELEMENT

MSTS

TEMP. PROBE

AutoFlush

CT-SteamStop

iTempo/Plus or

iSteam Control

Transformer

POWER INPUT

L1 L2

GROUND

Express

Steam

WATER

FEED

SOLENOID

VALVE

THERMOSTAT

HEATER

FACTORY

WIRI N G

FIELD

WIRING

LE G E N D

(All Diagrams)

CONTROL BOARD

CONTACTOR

Heating Element

To Probe

AutoFlush

CT-SteamStop

iTempo/Plus or

iSteam Control

TRANSFORMER

POWER INPUT

L1 L2

FUSES

GROUND

WATER

FEED

SOLENOID

VALVE

Express

Steam

THERMOSTAT

HEATER

FACTORY

WIR ING

FIE LD

WIRING

L E G E N D

(All Diagrams)

FACTORY

WIRIN G

FIELD

WIRIN G

L E G E N D

(All Diagrams)

CONTACTOR

To Probe

THERMOSTAT

CONTROL BOARD

AutoFlush

CT-SteamStop

iTempo/Plus or

iSteam Control

TRANSFORMER

POWER INPUT

L1 L2 L3

GROUND

WATER

FEED

SOLENOID

VALVE

THERMOSTAT

HEATER

Express

Steam

Single Phase

Wiring Diagrams

MODEL CT6E

& CT9E

MODEL CT12E

& CT15E

Three Phase

Wiring Diagrams

MODEL CT6E, CT9E

& CT12E

Maintenance

Mr.Steam steam ath generators require little maintenance.

Other than draining, maintenance procedures are minimal. When

AutoFlush is not installed the manual drain valve should e opened

fully flushing out accumulated materials, salts and other particles

which are natural y-products of oiling water, after each use.

Flush a minimum of two-three hours after the con-

trol has een turned off to insure that the water has cooled.

Draining immediately after a steam cycle may

expose PVC and other piping to high temperature water. Check

local codes. The unit will refill automatically after 10 minutes. In

areas of hard water, a Mr.Steam AutoFlush®system is recommended

for generator longevity.

Steam Generator Operation

Mr.Steam recommends eginning steam athing at a low tempera-

ture setting to gauge comfort and safety levels. Set the duration at

10 minutes max. to gauge comfort and safety levels. This will allow

the steam generator to heat up and egin producing.

Initial Start-Up an Checkout

1. Turn on control. Follow specific instructions provided

with controls.

2. Steam will egin to appear in approximately 5 min-

utes at the steam head. Steam will shut off when

desired temperature is reached and will automatically

resume when room temperature drops elow set

point.

3. Steam will shut off automatically when control counts

down to zero. To shut steam off manually, turn con-

trol OFF. To clear steam from enclosure area, turn

shower on efore opening door.

4. If unit does not start and control does not turn ON

(control display does not light up) then turn reaker

off for 20 seconds and try again.

5. Refer to specific instruction sheets for installation,

operation and maintenance of optional equipment

and Control.

Transformer

Liquid Level

Control Board

Water Feed

Solenoid

Water Feed

AutoFlush

Plug and Play

Connector

Thermostat

Liquid

Level Probe

Power Supply

Knock-Out Contactor

Steam Outlet

Troubleshooting

Step 1

Check your main incoming power

to the unit.

Step 2 Verify the transformer is receiving

208/240 VAC.

Step 3 Verify that you have 24VAC coming

out of the transformer, WHT & WHT/BLU

wires, into the oard.

Step 4 Verify that you have the green

light on the PC oard.

Step 5 Push the white test utton to run

the generator on a 10 minute test cycle.

Step 6 Verify that you have 24 VAC to the

water feed solenoid, GRY & WHT/GRY

wires (will fill when needed).

Step 7 Temporarily short out the WLS

(Purple wire) and GND (Green wire)

terminals and verify the contactor engages.

Step 8 When the red light is on, verify

that you have 24 VAC, RED & WHT/RED

wires, to the contactor.

Step 9 Check to see that you have

your main voltage on the load side of

the contactor when it is engaged.

Step 10 If all steps on the power path

were verified, turn off power to the

unit and pull the heating element via

the left hand access panel for inspec-

tion.

Do not isassemble internal components, internal components contain no serviceable parts.

WARNING

CAUTION

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

NOTE: FOR ILLUSTRATIVE

PURPOSES ONLY.

Some components may e omitted

or altered for clarity. Do not use for

wiring, repair or other purposes not

related to component identification.

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

RED(Heater)

YELLOW(Water Level)

GREEN(Power)

Force On

Test Button

System Status Co es

The iTempo/Plus control may display a status code if the steam generator is not functioning properly.

Co e Co e Meaning Probable Cause Suggeste Reme y

H20 Water level is not Water Supply is off Turn on Water Supply

satisfied within 5 min. Defective water feed solenoid Check/replace water solenoid valve

Water feed pro e not functioning Check/clean pro e.

Check pro e wiring.

Drain Valve Open Check/Close drain valve

AutoFlush not functioning Check/Replace AutoFlush

Prr1 Temperature Pro e Error Control/Remote sensor ca le cut Replace Control Ca le/Sensor

or Prr2 Internal pro lem with control/Remote Sensor Replace ControlSensor

Err1 Incorrect Field Supply Voltage Incorrect voltage supplied Supply steam generator with the correct

(green light on liquid level to Generator voltage noted on the data plate la el.

control oard will e off)

Err2 Button on control is pressed Control cover misalignment Remove and reinstall control cover

for more than 5 minutes De ris ehind control cover Remove control cover and clean cover,

control and keypad with a damp cloth

Err7 Liquid Level Control Board Memory error in LLCB Press ON/OFF to clear.

malfunction Replace control if code remains.

Liqui Level Control Boar -

EXPLANATION OF LED INDICATORS

_____________________________________________________________________________________________________________________________________________

GREEN LED is ON when there is 208/240 Volt incoming power connected,

24 Volt transformer secondary output and on- oard 5 Volt DC control power are present.

_____________________________________________________________________________________________________________________________________________

YELLOW Water level indicator–LED is OFF when no water is detected (for more that 5 seconds). ON when

water level is satisfactory. For units with AutoFlush, if more than five hours have elapsed since

last usage and this LED is ON it is indicative of an AutoFlush or water level pro e circuit malfunction.

_____________________________________________________________________________________________________________________________________________

RED Contactor relay indicator–LED is ON when relay is closed and sending 24 Volts to the

contactor coil. (This LED comes ON if the generator is ON.)

_____________________________________________________________________________________________________________________________________________

FORCE ON This utton is for trou le shooting only and will operate if a control is connected or not.

TEST BUTTON Pressing the utton again will shut the generator OFF.

The test utton will only allow the generator to operate for 10 minutes.

_____________________________________________________________________________________________________________________________________________

Liqui Level Control Boar

PN 103975

(shown without wiring)

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

AutoFlush®

Box Contents

•AutoFlush Valve with Cord

• Installation instructions.

Operation

The AutoFlush System feature automatically drains

the CT system following each use.

A time delay allows the water to cool down (a out

two hours) efore it drains y gravity for a safe and

gentle operation. Unit drains by gravity.

Installation Instructions

1. Plum ing to e performed y a qualified

plum er and shall e in accordance with

applica le national and local codes. Unit drains

y gravity. A drain line that is lower than the

AutoFlush assem ly must e availa le. The

AutoFlush System valve outlet is 1" NPT. Check

plum ing code for receptor, trap and vent requirements.

2. Use copper or rass nipple 1" NPT x 31⁄2" or longer

(not supplied) to connect AutoFlush valve to the Drain Valve,

noting the direction of flow on the valve ody.

DO NOT REMOVE THE DRAIN VALVE

Removal may cause equipment and property damage.

If there is not enough room for the valve, an el ow and

a short nipple (not provided) can e added.

3. Open Drain Valve (handle must e aligned with rass nipple).

4. Connect the AutoFlush System cord connector to

the three pin connector as shown.

Do not drain into a steam enclosure or any

location where accidental contact with drain water may occur.

In the event of a power failure the AutoFlush System valve will

open and may discharge oiling water.

Sweat Fittings

When using sweat fittings use only tin ase solder with a melt-

ing point elow 600 degrees F. Do not overheat. Ends of water

supply tu ing must e thoroughly clean for a minimum distance

of 1" from ends. Do not remove valve cover.

To Check Operation

1. Turn on Mr.Steam and allow tank to fill with water.

2. Turn off Mr.Steam control. Water should stay in tank.

3. Turn off power at the panel ox. Water should

discharge from tank.

4. Turn on power at panel ox.

5. Repeat

Drain Valve

DO NOT TURN OR REMOVE

THE DRAIN VALVE

(shown in the correct open position)

Steam Generator

ipple Plumb to

Drain Line

AutoFlush Valve

AutoFlush Cord

AutoFlush Valve

3 Pin Connector

for AutoFlush

AutoFlush Cord Connector

Drain Valve

(shown in the correct open position)

DO OT REMOVE THIS DRAI VALVE

Steam Generator

ipple

copper or brass

nipple 1" PT x

31⁄2"or longer

(not supplied)

Plumb to

Drain Line

Arrow indicates correct

direction of flow

WARNING

CAUTION

PROVIDE DRAIN PLUMBING ACCORDING

TO LOCAL CODES. PLUMB AS REQUIRED

FOR AUTOFLUSH SYSTEM.

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Drip Pan

Mr. Steam provides

a drip pan in the unlikely

event of a plum ing leak.

Locate the drip pan on a solid level surface

and place the steam generator inside the drip

pan. Insure the steam generator is level (see

page 4 for locating the steam generator).

All plum ing shall e performed y a qualified

licensed plum er and in accordance with

applica le national and local codes. Check

local plum ing code for receptor, trap and

vent requirements.

Drip pans drain y gravity. The drip pan is

equipped with an integral 3⁄4" NPT fitting.

Express Steam

(Factory installed)

All CT models have Express Steam standard.

Express Steam is equipped with a low

power heating element and thermostat to

keep the water in the tank warm enough to

ring up steam quicker. All Express Steam

components and wiring are installed at the

factory. No additional wiring or plum ing is

required y installers.

NOTE: FOR ILLUSTRATIVE PURPOSES ONLY

Some components may e omitted or altered

for clarity. Do not use for wiring, repair or other

purposes not related to component identification.

Replacement Parts List

____________________________________________________________

Part No. Description Pro uct

____________________________________________________________

99178CT Drain Valve All models

99297 Safety Valve 15PSI All models

100479 Water Feed Solenoid All models

Valve w/filter

10477-3 Transformer 24VAC All models

103975 Liquid Level Control Board All models

103990-60 Ca le for iTempo/Plus iTempoPlus only

Control (60 ft.)

MSTS-60 Remote Temperature Pro e iTempoPlus only

100476-2 Contactor 50A 2-pole CT6E & CT9E,

Single phase

99012 Contactor 50A 3-pole All 3-Phase models

103453 Contactor 50A 4-pole CT12E

100471-2 Pro e Assem ly All models

99096MS Heating Element Gasket All models

103412 Acrylic Shield All Models

99314 Power Fuse 60A 250V CT12E, Single phase

29061BMS Heating Element 6 KW 208V CT6E

29061CMS Heating Element 6 KW 240V CT6E

29091BMS Heating Element 9 KW 208V CT9E

29091CMS Heating Element 9 KW 240V CT9E

29121BMS Heating Element 12 KW 208V CT12E

29121CMS Heating Element 12 KW 240V CT12E

29151BMS Heating Element 15 KW 208V CT15E

29151CMS Heating Element 15 KW 240V CT15E

103978-60 Ca le for CT-SteamStop (60 ft.) All models

104016 Thermostat All models

104015 Express Steam Thermostat All models

104019 Heating element All models

for Express Steam

104117-30 Ca le for iSteam (30 ft.) iSteam Only

104117-60 Ca le for iSteam (60 ft.) iSteam Only

iMSTS Remote Temperature Pro e iSteam Only

Transformer

Drain Line

Liquid Level

Control Board

Fuses

Water Inlet

Water Feed

Solenoid

Safety Valve

AutoFlush

Valve

Stainless

Steel Tank

Heating

Element

Access Cover

Thermostat

Liquid Level Probe

AutoFlush Plug and

Play Connector

(see page 13)

Power Block

Power Supply

Knock-Out

Steam Outlet

Express

Steam

Contactor

Mo els CT6E & CT9E

shown with cover removed

NOTE: FOR ILLUSTRATIVE

PURPOSES ONLY.

Some components may e

omitted or altered for clarity.

Do not use for wiring, repair

or other purposes not related to

component identification.

Mo els CT12E

shown with cover removed

NOTE: FOR ILLUSTRATIVE

PURPOSES ONLY.

Some components may e omitted

or altered for clarity. Do not use for

wiring, repair or other purposes not

related to component identification.

Contactor

Transformer

(100477-3)

Drain

Line

Liquid Level

Control Board

(103975)

Water Feed

Solenoid (100479)

Water Inlet

Safety

Valve

AutoFlush

Valve (CT81500)

Stainless Steel Tank

Heating Element

Express Steam

(104019)

Access Cover

Thermostat

(104016)

Liquid Level

Probe

(100471-2)

AutoFlush Plug and

Play Connector

(see page 13)

Power Supply

Knock-Out

Steam Outlet

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

Do not route iSteam, iTempo/Plus, iTempo,

HomeWizard or iGenie control wiring inside conduit

together with power lines or close to hot water or steam

piping. Doing so may result in an inoperative or hazardous

installation.

Do Not alter or modify any Mr.Steam prod-

uct. Doing so may result in an inopera le or hazardous

installation and will void the warranty

IMPORTANT NOTES:

1. Turn power to the steam generator OFF efore con-

necting the control to the generator. Failure to turn the

power off will result in an inopera le control.

2. Do not operate iSteam, iTempo/Plus, iTempo,

HomeWizard or iGenie controls with other than a

Mr.Steam iSteam or iTempo compati le steam genera-

tor. Mr.Steaml steam generators with serial num ers

lower than 900000, or any other rand of steam gener-

ator are not to e operated with iTempo controls.

Doing so may result in an inoperative or hazardous

installation. If iSteam is used with a generator having

serial num er 900000 through 930030, contact

Mr.Steam technical support for an upgraded PC oard.

3. This document contains important safety, operation and

maintenance information. Leave this document with

management. Do not discard this document.

4. Discontinue use of the steam generator or control if the

steam generator is damaged or otherwise not function-

ing properly. Operating a damaged steam generator

may result in an inoperative or hazardous installation

.steam®

CLUB THERAPY Controls

_________________________________________________________________________________________

Control Rough In

Refer to Installation Instructions for the specific control

IMPORTANT NOTE: The control ca les should e run in dedicated 1" conduit to facilitate installation and service.

1. Determine the desired installation location of the

control. The iSteam®, iTempo™and iTempo/Plus™

controls are designed to e installed inside or out-

side the steam room as a matter of personal prefer-

ence. If the control is installed inside the steam

room the control must e located:

4-5 feet a ove the floor near the ather seating area

3. The control features an integral temperature sensor.

Locate the control in a location representative of the

desired steam athing temperatures.

Do not locate the control a ove or near the steam

head or direct steam emissions.

4. on a vertical wall

The control ca le length is 30 feet. Insure that the

control and/or steam generator are located according-

ly. An optional 60 foot ca le is availa le, PN 103990-60 for

iTempo and PN 104117-60 for iSteam. Contact a Mr. Steam

technical service representative if a 60 foot ca le is required.

IMPORTANT NOTES: If the control is installed outside the

steamroom a Remote Temperature Pro e Part Num er MSTS or

iMSTS must e installed inside the steam room, depending on

the control. Insure Mr.Steam steam generator is iSteam or

iTempo compati le and has a serial num er 900000 or higher. If

iSteam is used with a generator having serial num er 900000

through 930030, contact Mr.Steam technical support for an

upgraded PC oard.

See instructions for the MSTS or iMSTS Temperature Pro e

(located in the Control Installation Manual related to your spe-

cific control package) efore rough-in or installation of control.

Before Installing

Turn power to the steam generator OFF efore connecting the

control to the generator. Failure to turn the power off will result in

an inopera le control.

To avoid unintentional steam ath operation,

do not locate the control where other controls, accessories,

shower heads, valves, ody sprays or similar within the show-

er could cause confusion or interfere with the Mr.Steam con-

trol’s intended use and function.

Do not use any iSteam®, iTempo/Plus™,

iTempo™, HomeWizard™or iGenie®controls without reading

and understanding its own manual and the Mr.Steam steam

generator Installation and Operation Manual. Failure to read

and understand these instructions may result in an inopera-

tive or hazardous installation.

The warning placard located in the documenta-

tion envelope must e read and permanently affixed in a con-

spicuous location near the steam room. Failure to read and affix

this warning placard in a conspicuous location may result in seri-

ous injury or death.

Install the iSteam, iTempo or iTempo/Plus controls according

to installation instructions. Failure to install according to

instructions will result in an inoperative control or hazardous

overheating or inadequate heating of the steam room.

If an iSteam, iTempo or iTempo/Plus control is installed out-

side the steam room a Remote Temperature Pro e (PN MSTS

or iMSTS) must e installed inside the steam room per instal-

lation instructions supplied with the Remote Temperature

Pro e. Failure to install according to instructions will result in

an inoperative control and overheating of the steam room.

CAUTION

WARNING

Control Installation

Refer to Control Manual for specific installation re uirements

.steam®

C L U B T H E R A P Y Controls

_________________________________________________________________________________________

30' ca le

Switch Plug & Play

Connector

Diagram 1

Diagram 2

Diagram 3

Diagram 4 Diagram 5

Diagram 6

CT SteamStop™

On/Off Switch for iTempo/Plus®

Dimensional Information

Box Contents:

• CT SteamStop Control

• Owner’s Manual

• 60’ CT SteamStop Ca le

IMPORTANT NOTE: The control ca les should e run in dedicated 1"

conduit to facilitate installation and service.

Installing the CT SteamStop Control

The CT SteamStop has a 60 foot ca le with a Plug & Play connector

at oth ends. (Diagram 1) The CT SteamStop must e installed

inside the steamroom.

Step 1 Diagram 2

Drill a 7

⁄8inch diameter hole in a preferred wall location.

Do not oversize or undersize the hole.

Step 2 Diagram 3

Route the ca le from the wall to the steam generator. Be careful

not to strain, pinch or otherwise damage the control ca le.

Step 3 Diagram 4

Remove and discard the peel-off paper from the switch housing

to expose the adhesive as shown in Diagram 4.

Step 4 Diagram 5

Apply silicone (provided with the iTempo/Plus control) to the hole

in the wall as required to create a moisture seal. Apply silicone to

the ack of the switch as required to seal grout lines or as required

for additional adhesion.

IMPORTANT: Use care not to apply silicone to the adhesive gasket.

Step 5

Push ca le and switch housing into the hole firmly.

Step 6 Diagram 6

Firmly connect the Plug & Play connector to the steam generator

connector la eled CT SteamStop.

NOTE: The connector is keyed and will only connect in one

orientation with the ta facing up.

LED indicator will light up

when the generator is ON.

Using the CT SteamStop®Control

The CT SteamStop control should e installed in the steam

room for the user to start and stop the steam ath

Note: If an error code is detected y the system the LED indi-

cator will flash. Refer to the iTempo/Plus or iSteam display for

error code or call a Mr. Steam’s service technician.

NOTE:

For Illustrative Purposes Only. Drawings Not to Scale

Warranty

To view or download the Mr. Steam Steam Generator Warranty

and register your Product go to: blog.mrsteam.com/wr

Care Tips for all Controls an Steamhea s

1. Use only mild soap and water on a soft cloth to

clean the control and steamhead.

2. Do not use a rasive cleansers.

3. If the decorative cover is damaged on the

iTempo/ Plus call Mr.Steam technical service for

replacement parts.

NOTE: Replacement of the decorative covers

requires removal and reinstallation of the control

from the mounting surfaces.

.steam®

C L U B T H E R A P Y Installation, Operating & Maintenance Manual

_________________________________________________________________________________________

.steam®

Feel Good Inc.

www.mrsteam.com

mr.steam®

Sussman-Automatic Corporation®I[email protected] Iwww.mrsteam.com

43-20 34th Street, Long Island City, NY 11101

TEL: 1 800 767 8326 FAX: 718 472 3256

2014 © Sussman-Automatic Corporation I Mr.Steam and des., AromaFlo, AutoFlush, AutoSteam, Butler Package, ChromaSteam, Clean Steam...Every Time, Clu Therapy, Digital 1, Express Steam,

From Bathroom to Spa, iGenie, iSizing, iSteam, iSteam/Plus, Making Wellness a Way of Life, MusicTherapy, Spa Package, Steam Genie, Steam on Demand, Steam@Home, SteamTherapy, Sussman,

Valet Package, Virtual Spa System, Voice Genie and Voice Wizard are registered trademarks of Sussman-Automatic Corporation. AudioWizard, A Lifetime of Pleasure, HomeWizard, iButler,

iSteamTV, iTempo, iTempo/Plus, MySteam, Smart Sizing, Steam in a Box, SteamStart, SteamStop, and The Intelligent Steam ath are trademarks of Sussman-Automatic Corporation.

PUR

100426 2.15

Products, information and specifications are su ject to change without notice.