mr. steam CT9E Instruction manual

mr
.steam®clubtherapy®
Club Therapy Steambath Generator Systems
Installation, Operation & Maintenance Manual
Models CT 6E, CT 9E, CT 12E, CT 15E

Club Therapy
®
Steambath Generator Systems
INSTALLATION, OPERATION & MAINTENANCE MANUAL
mr.steam®clubtherapy®
TABLE OF CONTENTS
Read Me irst! & Warning Sticker . . . . . . . . . . . . . . . . . . . . . 1
Select Your Club Therapy Model . . . . . . . . . . . . . . . . . . . . . . 2
_______________________________________________________________
Before Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Steam Room Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Locating the Steam Generator Unit . . . . . . . . . . . . . . . . . . . 4
Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation: Plumbing, Water Supply, Drain, Steam Outlet
Safety Valve, Drain Pan, AromaSteam . . . . . . . . . 5
Steam Head Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Generator Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Specifications & ield Power Wiring . . . . . . . . . . . . 8
Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Initial Start-Up & Checkout, Maintenance . . . . . . . . . . . . . . 10
Auto lush®System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drain Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Liquid Level Control Board . . . . . . . . . . . . . . . . . . . . . . . . . 12
Replacement Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . 13
Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Control System Installation
eTEMPO/PLUS®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-17
CT-STEAM STOP™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MSTS Temperature Probe. . . . . . . . . . . . . . . . . . . . . . . 19-20
Control System Operation
eTEMPO/PLUS®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22
CT-STEAM STOP™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using Aromasteam Essential Oils. . . . . . . . . . . . . . . . . . . . . 23
Safety Information and Care Tips,. . . . . . . . . . . . . . . . . . . . 24

RE AD ME F IRS T!
IMPORTANT NOTE: As you follow these
instructions, you will notice warning and
caution symbols. This blocked information is
important for the safe and efficient installa-
tion and operation of this generator. These
are types of potential hazards that may occur
during this installation and operation:
states a hazard may cause serious injury or
death if precautions are not followed.
signals a situation where minor injury or
product damage may occur if you do not
follow instructions.
IMPORTANT NOTE: This highlights
information that is especially relevant to a
problem-free installation.
All nformat on n these nstruct ons s based on
the latest product nformat on ava lable at the
t me of publ cat on. Sussman-Automat c Corporat on
reserves the r ght to make changes at any t me
w thout not ce.
!CAU T I ON
!WAR N ING
mr.steam®
Sussman-Automatic
Corporation®
[email protected]
www.mrsteam.com
Club Therapy®Steambath Generator Systems MODEL _______________________
INSTALLATION, OPERATION & MAINTENANCE MANUAL SERIAL NO._____________________
MODELS: CT6E, CT9E, CT12E
43-20 34th Street
Long Island City, NY 11101
TEL: 1 800 76 STEAM
AX: 718 472 3256
9410 S. La Cienega Blvd.
Inglewood CA 90301
TEL: 1 800 72 STEAM
AX: 310 216 2944 M A D E I N U S A
PUR 100426 Rev 8.0/12
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1.READ AND FOLLOW ALL INSTRUCTIONS
2. Do not permit children
under the age of 16 to use this steambath.
3.
To reduce the risk of injury:
A. The wet surfaces of steam enclosures may
be slippery. Use care when entering or
leaving.
B. The steam head is hot. Do not touch the
steam head and avoid the steam near the
steam head.
C. Prolonged use of the steam system can
raise excessively the internal human body
temperature and impair the body’s ability
to regulate its internal temperature
(hyperthermia). Limit your use of steam
to 10-15 minutes until you are certain of
your body’s reaction.
!W A R N I N G
!W A R N I N G
A warning placard has been provided
in the Information envelope.
This placard is to be applied to
the wall of the installed shower
or steam enclosure.
D. Excessive temperatures have a high
potential for causing fetal damage
during the early months of pregnan-
cy. Pregnancy or possibly pregnant
women should consult a physician
regarding correct exposure.
E. Obese persons and persons with a
history of heart disease, low or high
blood pressure, circulatory system
problems, or diabetes should consult
a physician before using a steam-
bath.
F. Persons using medication should con-
sult a physician before using a
steambath since some medication
may induce drowsiness while other
medications may affect heart rate,
blood pressure and circulation.
SAVE THESE INSTRUCTIONS
REDUCE THE RISK OF OVERHEATING AND SCALDING
1. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY OR SLEEPY.
STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING.
2. CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH.
3. CHEC WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR
HEALTH OR UNDER MEDICAL CARE.
4. BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL,
DRUGS, OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS.
5. DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD.
REDUCE THE RISK OF SLIPPING AND FALL INJURY
1. USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM. FLOOR MAY BE SLIPPERY.
NOTE: FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER’S MANUAL
mr.steam®43-20 34th Street , Long Island City NY 11101 1 800 76 STEAM www.mrsteam.com PUR100378 6.4/08
WARNING
!
1

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
2
IMPO TANT: The guidelines for selecting the steambath
generator is a recommendation only. Because of variables
in construction, these sizing instructions and specifica-
tions should be considered as guidelines only. Mr.Steam®
will review the model selected provided we receive com-
plete information, including working drawings, specifica-
tions, and pertinent electrical and construction details.
Otherwise, the manufacturer disclaims responsibility for
the sizing of a model selected.
IMPO TANT: or steam rooms constructed of acrylic or
synthetic materials, select next lower-rated CT model.
WA NING: In considering a purchase of this steambath
system, please note that if users are pregnant, have a coro-
nary condition, are in poor health, are being treated for
any other medical condition, or are using medication or
drugs, Mr.Steam recommends that you obtain the approval
of their physician before use. or information about this
product and safety issues, please call us at 1-800-76-STEAM
or log onto www.mrsteam.com for a copy of the
Installation/Operation/Maintenance Manual.
IMPO TANT: The total adjusted room volume allows for up
to 60 feet of insulated steam line from the CT generator to
the steam room. If the 60 feet line is exceeded consult
with factory. When locating the steam generator consider-
ation of the control and MSTS location must be taken into
account. The maximum length for a control cable is 60
feet. The maximum length of the MSTS cable is 60 feet.
Residential Steam Generators Specification Chart
Amps (for Total Adj Wire Water Usage Shipping
Model No. KW 240v/1P )† Room Vol. Size‡ gallons†† Dimensions* Wt. (lbs)**
CT6E 6 25 150 8 0.80 17"L x 18½"H x 77⁄8"D 40
CT9E 9 38 360 8 1.2 17"L x 18½"H x 77⁄8"D 40
CT12E 12 50 575 6 1.6 17"L x 18½"H x 77⁄8"D 40
CT15E 15 63 675 4 2.0 17"L x 18½"H x 77⁄8"D 40
IMPORTANT: Add C1 suffix to Model No. for 240V/1Ph; Add B1 suffix to Model No. for 208V/1Ph.
IMPORTANT: All CT MS Models are cUL us Listed and CE; approved.
NOTES: All CT Generators available in 240v/1PH, 208v/1PH and other voltages/phases.
† Amps are for 240/1PH rated units.
‡Wire size (AWG) based on minimum 90˚C rated THHN copper conductors.
Refer to the National Electrical Code for other types of conductors.
*Dimensions are for generator only, without
AutoFlush® or plumbing features.
**Shipping weight and pricing are for generator
only, without control or steamhead.
†† Water usage based on 20 minutes of operation.
M
Ma at te er ri ia al ls s o of f c co on ns st tr ru uc ct ti io on n, , r ro oo om m s si iz ze e a an nd d s sp pe ec ci ia al l d de es si ig gn n
f
fe ea at tu ur re es s s su uc ch h a as s l la ar rg ge e g gl la as ss s a ar re ea as s, , a al ll l a af ff fe ec ct tt th he e s st te ea am m g ge en ne er ra at to or r m mo od de el l s se el le ec ct ti io on n. .
1. Measure length, width & height in feet of the steam/shower or tub/shower
Multiply the Length ____ x Width_____ x Height _____ =
2. Construction Materials:
or natural stones: natural marble, Add 110%
stone, shale, glass block or concrete
or ceramic or porcelain tile on Add 40%
cement board or mortar bed
3. Ceiling Height: or each foot above 8 feet Add 15%
4. Add all figures above to obtain the Total Room Volume required
ROOM OLUME
TOTAL ADJUSTED
ROOM OLUME
SELECT YOUR MR.STEAM®
Compare your TOTAL ADJUSTED ROOM VOLUME to the Specification Chart below
and select the appropriate model.
Visit www.mrsteam.com to size your generator online automatically.

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
3
9.
Limit steam room ceiling height to 8 feet. Exceeding
8 feet may require a higher-rated steam generator.
10. A peel-off warning label has been provided in the Information
envelope (see Warning facsimile below).
This label is to be applied to the wall of the installed
shower or steam enclosure.
The MS series of steam generators are
for residential use only. Commercial or other nonresidential
applications void the warranty and may adversely affect
product performance.
BEFORE INSTALLING
Carefully inspect the Steam Generator and packaging for ship-
ping damage. Please contact the carrier in the event of shipping
damage, please contact the carrier for claim information. Our
customer service department can assist you with any missing
or damaged parts.
Never use damaged equipment, doing so
may result in an inoperative or hazardous installation.
IMPORTANT NOTES:
• This document contains important safety, operation and
maintenance information. Leave this document with the
homeowner. Do not discard this document.
• Discontinue use of the steam generator and control if the
steam generator or control are damaged or otherwise not
functioning properly. Doing so may result in an inoperative or
hazardous installation
IMPORTANT: The following general information should be
used in conjunction with consultations with an architect,
designer and contractor in determining factors necessary in pro-
viding a suitable and safe steam room.
Read these instructions before installation or service. Although
this MS steambath generator has been fully qualified for ship-
ment by Mr.Steam®, the following must be reviewed for proper,
safe and enjoyable steam bathing:
• Verify that the model and accessories are correct, including
incoming line voltage.
STEAM ROOM GUIDELINES
1. Steam room must be completely enclosed, with full walls,
door, floor and ceiling.
2. It is recommended that a gasketed door is used for heat seal-
ing and steam containment.
3. If tile-type or other smooth surfaced flooring is used provide
suitable anti-skid strips or equivalent, to
prevent user slipping and injury.
4. Walls and ceilings must be constructed of water-resistant,
non-corrosive surface, such as tile, marble, molded acrylic,
or other non-porous material. The ceiling should be sloped to
prevent dripping of condensate.
If acrylic, fiberglass or other non-heat
resistant materials are used as part of the steam room enclosure.
Consult with the material manufacture and see pg. 7, Steamhead"
for additional details.
5. Provide a floor drain.
6. No heating, venting or air conditioning devices should be
installed inside the steam room.
7. Steam room tile construction information is
available from the Tile Council of America, Inc. by purchas-
ing the TCA Handbook for Ceramic Tile Installation.
Tel: [phone] or www.tileusa.com.
8. Windows that are part of the steam room should be double
paned and tempered safety glass.
!WAR N ING
• Insure steambath generator has been correctly sized for the
steambath room. Pay particular attention to room volume and
construction. If any questions, please refer to Mr. Steam sizing
and selection guide on page 2.
• Marble or glass walls or ceilings, or exterior walls “ENLARGE” the
room’s size, requiring a generator larger than one based only on
the room’s cubic foot (L x H x W) volume.
• The physical size of the unit, clearance for plumbing servicing,
and its distance from the steam room must all be considered
before final installation.
• Consider any options and accessories before initiating installa-
tion. Read the Installation and Operation Manual of all options
and accessories available at www.mrsteam.com technical down-
loads.
IMPORTANT: Mr.Steam units are intended to be operated with
Mr.Steam eTempo/Plus®, eTempo®Home Wizard™and Steam Genie®
controls only, and are to be installed strictly in accordance with the
specific instructions contained in this manual and as supplied in
the manuals provided with the controls.
ELECTRICAL SHOCK HAZARD. Mr.Steam steam
generators are connected to 240V line voltage and contain live
electrical components. All installation and service to be performed
by qualified and licensed electricians and plumbers only. Installation
or service by unqualified persons or failure to use Mr. Steam parts
may void the warranty.
!WAR N ING
!WAR N ING
!CAU T I ON
Not Actual Size
REDUCE THE RISK OF OVERHEATING AND SCALDING
1. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY OR SLEEPY.
STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING.
2. CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH.
3. CHEC WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR
HEALTH OR UNDER MEDICAL CARE.
4. BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL,
DRUGS, OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS.
5. DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD.
REDUCE THE RISK OF SLIPPING AND FALL INJURY
1. USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM. FLOOR MAY BE SLIPPERY.
NOTE: FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER’S MANUAL
mr.steam®43-20 34th Street , Long Island City NY 11101 1 800 76 STEAM www.mrsteam.com PUR100378 6.4/08
WARNING
!

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
4
LOCATING T E STEAM GENERATOR UNIT
Select a location as near as practical to the steam room. Typical locations include: closet, vanity cabinet, heated attic or basement.
NOTE: T E LENGT OF T E CABLE FOR CONNECTING T E MSTS TO T E STEAM GENERATOR IS 30 FEET.
(ITEMS 1-7)
1. DO NOT install steambath generator or plumbing lines in
unheated attic or any locations where water could freeze.
2. DO NOT install steambath generator inside steam room.
3. DO NOT install steambath generator outdoors or wherever
environmental conditions may affect the safety and/or
performance of the generator.
4. DO NOT install steambath generator near flammable or corrosive
materials or chemicals such as gasoline, paint thinners, or the
like. Installation in areas having high concentrations of chlorine
(such as pool equipment room) must be avoided.
5. Install steambath generator on a solid and level surface. Keyhole
slots are provided for wall mounting. Insure the steam generator
is properly secured and level when mounting with keyhole slots.
6. Install steambath generator in an upright position only.
7. Steam line, safety valve, drain valve, plumbing and steamheads
become hot during operation and remain hot after shutdown for
a period of time. Provide appropriate protection, including insu-
lating plumbing lines. Avoid plumbing runs and steamhead loca-
tions that can come in contact with bathers.
NOTE: FOR ILLUSTRATIVE PURPOSES ONLY.
Consult with qualified designer, architect or
contractor for steam room construction details.
Provide unions as required to facilitate
installation and disconnect of piping
Steam
Generator
Field installed
power supply
Field installed
steam supply pipe
Drain Valve should be closed
when AutoFlush is not installed
Control
cable
Steam Head (shown with optional acrylic shield)
See page 6 for Steam Head Installation information
MSTS
see page 19-20 for
installation instructions.
eTEMPO/PLUS® Control
See page 15-17 for
Installation information.
CT-STEAM STOP™Control
See page 18 for
installation information.
Field installed
water supply line
IMPORTANT:
Locate the remote sensor (MSTS)
in a location representative of the desired steambat-
hing temperatures. Do not locate the control above or
near the steam head or direct steam emissions.
TYPICAL MR.STEAM® INSTALLATION
!WAR N ING
IMPORTANT: (ITEMS 8-11)
8.
Install anti-water hammer device as necessary.
9 . Provide a minimum of (12) inches at both ends and
top of the steam generator or as required for servicing.
See page 7.
10. Provide unions as required to facilitate installation
and disconnection of piping.
11 . The eTempo/Plus should be placed in a location only
accessible by the facility’s staff. The CT-STEAM STOP™
and remote sensor (MSTS) are required to be
installed inside the steamroom.
NOTE: Mr.Steam Generators (inclusive of the eTempo
series Controls) are CE and UL listed.
The CT series of steam generators
are for Commercial use only.
!WAR N ING
When installing the optional AromaSteam,
install a downward facing 90-degree T in the
steam supply line. See the AromaSteam
Installation Manual for complete information.

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
5
INSTALLATION
Plumbing
All plumbing shall be performed by a qualified licensed plumber and
in accordance with applicable National and local codes.
• Use unions on all pipe connections.
• Use only brass piping or copper tubing as permitted by codes.
• Do not use black, galvanized, PVC, or PEX pipe.
ater Supply (3⁄8" NPT)
1. Connect to cold water line.
2. Provide a shut off valve in the water supply line upstream of the steambath generator.
3. Do not overheat inlet solenoid valve with solder connections. Overheating will damage parts.
4. lush inlet water line thoroughly before making connection to unit.
5. Strainer recommended upstream of feed water connection.
6. or best performance water pressure should be 15 to 20 psig.
Reduce pressure as required.
7. Provide anti-water hammer device as required.
8. Install an approved backflow preventer as required by local codes.
Drain (1" NPT)
NOTE: A drain valve is provided to facilitate servicing. Provide a drain line connection from steambath
generator drain valve according to National and local Codes. Check local plumbing code for receptor,
trap and vent requirements. Unit drains by gravity. Two hours after the generator has been turned off
the Auto lush valve automatically will open and drain the generator.
Steam Outlet (1⁄2" NPT)
1. Do not install any valve in steam line. low of steam must be unobstructed.
2. Use 1/2-inch brass pipe or copper tubing from unit to steam head as permitted by codes.
3. Insulate steam line using pipe insulation rated 212° or higher.
4.
Pitch steam line 1/4" per foot towards steam head or steam generator to avoid valleys and trapping of condensate.
NOTE: Running the steam line down and then up will create a steam trap blocking the flow of steam.
NOTE: A 1.5" hole in the steam room is required to mount the steamhead.
Safety Valve (3⁄4" NPT)
Where permitted by local codes, provide an outlet plumbing connection for safety valve.
To insure proper and automatic safety valve operation: DO NOT connect a shut off valve
or a plug at safety valve outlet. DO NOT connect a shut off valve or any construction in steam supply pipe.
Drain Pan
Mr. Steam strongly recommends the use of a drain pan in the unlikely event of a plumbing leak. Check
local plumbing codes for receptor, trap and vent requirements. Drain pans drain by gravity. The drain pan is
equipped with an integral 3/4" NPT fitting. See page 12 for additional drain pan installation information.
Aromasteam™
If the optional Aromasteam Electronic Oil Delivery System ( PN : MS AROMA ) is to be installed, a 90 degree
T plumbing fitting must be installed at a designated location on the steam outlet line. See the Mr.Steam
Aromasteam Operation and Instruction Manual for installation information before the steam line is installed
at www.mrsteam.com technical downloads.
!WAR N ING

6
Steam Head Installation (1⁄2" NPT)
IMPORTANT: Do not disassemble steamhead. Mr.Steam’s steamhead is
shipped fully assembled and requires no additional assembly.
Because the steam head and direct steam
emissions are very hot, locate the steam head where incidental
contact by bather with the steam head or direct steam emission
cannot occur.
NOTE: A 1.5” clearance hole around the steam pipe is
needed to mount the steamhead.
STEP 1
Locate steam head 6-12 inches above floor, except for:
• Tub/shower enclosures, install 6 inches above tub top edge.
• or enclosures with acrylic or other non-heat resistant
flooring install Acrylic Shield Part Number MS-103938.
STEP 2
Install steamhead with the oil well facing up as shown.
Hand tightening is sufficient when teflon or equal pipe
thread sealing compound is used.
IMPORTANT NOTE: To preserve steam head finish, do not use wrench
or other tools to tighten. DO NOT use abrasive cleansers or chemi-
cals. Use only water with mild soap and a non-abrasive sponge.
Consult with supplier of acrylic, fiberglass and other
non-heat resistant enclosures for recommended steamhead location. Use
Acrylic Shield PN MS-103938. See instructions provided with steam shield.
STEP 3
Secure a bronze drop ear fitting to a header and run a 1/2" copper steam
line from the steam generator to the drop ear fitting. Install a temporary
nipple (6" or longer)in the drop ear fitting to locate the steamhead after
the wall is finished.
STEP 4
After the wall has been finished, mark on the nipple where the surface
of the wall is. Remove the nipple and measure the portion that was in
the wall (the end to your mark). Subtract 1⁄4" from that dimension and
select a brass nipple of that length to finish the installation.
STEP 5
Wrap teflon tape around the threads of the new nipple and screw
the nipple into the steamhead. Do not use wrenches or tools which
would damage the steamhead's finish. Wrap teflon tape around the
threads of the nipple and screw the nipple and steamhead assembly
you just made into the drop ear fitting in the wall. The steamhead
should be flush with the wall and the well must be facing up.
Care Tips for Steamheads
1. Use only mild soap and water on a soft cloth to clean the steamhead.
2. Do not use abrasive cleaners.
!CAU T I ON
!CAU T I ON
Oil Well
STEP 3
STEP 4
STEP 5
Steam Supply P ipe
End of pipe to
be recessed 1/4"
(without Acrylic Shield)
1/8" (with Acrylic Shield)
1/8" minimum clearance
required when Acrylic
Shield is used. See installa-
tion instructions provided
with the Acrylic Shield.
Apply with silicone or
equal sealant as required
for moisture seal.
Use Teflon or
equal sealant on
pipe threads
INSTALLING T E AROMASTEAM STEAM EAD
Steamhead
(shown w th
opt onal acryl c sh eld)
Locating Nipple
Drop Ear
itting
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
7
17"
(432)
2
3/8
"
(60)
23/8"
(60)
71/4"
(184)
121/2"
(310)
13/4"
(45)
183/4"
(466)
4"
(102)
6"
(152)
97/8"
(251)
13/8"
(35)
63/8"
(162)
77/8"
(200)
GENERATOR DIMENSIONS
WATER INLET 3/8” NPT
STEAM UTLET 1/2” NPT
SAFETY VALVE 3/4” NPT
MANUAL DRAIN VALVE 1” NPT
AUT FLUSH VALVE 1” NPT
NOTES :
1. M= ptional AutoFlush
2. All units in inches (MM)
Water Inlet
Control &
Accessory
Connections
Steam Outlet
Safety Valve
AutoFlush
Manual Drain Valve
IMPORTANT NOTE: Provide a minimum of (12) inches at
both ends and top of the steam generator or as required for
servicing. Alternately, provide unions as required to facili-
tate installation and disconnection of the steam generator.
IMPORTANT NOTE: The minimum clearance from com-
bustible surfaces is zero all around.
TO AVOID EQUIPMENT DAMAGE DO NOT CONNECT
POWER SUPPLY DIRECTLY TO ELEMENTS !!!
NOTE: FOR ILLUSTRATIVE PURPOSES ONLY.
Side View Showing
Element Access Panel

8
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Water Feed
Thermostat
Liquid Level Probe
Power Block
Power Supply
Knock-Out
Contactor
Steam Outlet
Fuses
AutoFlush Plug and
Play Connector
(see page 11)
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Water Feed
AutoFlush Plug and
Play Connector
(see page 11)
Thermostat
Liquid Level Probe
Power Supply
Knock-Out
Contactor
Steam Outlet
FIELD POWER WIRING
TO AVOID EQUIPMENT DAMAGE DO
NOT CONNECT POWER SUPPLY
DIRECTLY TO ELEMENTS!!!
L1, L2, GROUND TO BE FIELD WIRED
NOTE: FOR ILLUSTRATIVE PURPOSES
ONLY. CONSULT WIT QUALIFIED
LICENSED ELECTRICIAN FOR
ELECTRICAL INSTALLATION.
Models CT6E – CT9E
(single phase wiring shown)
Models CT12E
(single phase wiring shown)
ELECTRICAL
All electrical wiring to be installed by a qualified licensed electrician
in accordance with National Electrical Code and local electrical code.
Power Wiring- See “ ield Power Wiring” Diagrams (below)
1. Check power voltage. Use 240V rated unit when supply is greater
than 208V. Use 208V rated unit for 208V power.
2. Use minimum 90˚ C/300V rated insulated copper conductors only,
sized in accordance with National Electrical Code and local electri-
cal code for the current in Ampere Chart. If allowed by codes, NM
cable may require a larger wire size than as listed on the chart.
3. Connect suitably sized equipment grounding wire to ground termi-
nal provided.
4. Install a separate circuit breaker between supply and unit. Provide
a power supply disconnect within sight of the steam generator or
one that is capable of being locked in the open position.
5. or single phase units, use two-wire supply source and equipment
grounding wire. Neutral (white) wire is not required.
CHART
___________________________________________________________
MODEL MAX ROOM KW VOLTS WIRE SIZE WIRE SIZE
NO. VOL (CU. T.*) 1PH
†
PHASE AMPS (AWG) for 40˚C (AWG) for 45˚C
Ambient Ambient
___________________________________________________________
208 1 29 88
CT6E 150 6.0 3 17 10 10
240 1 25 88
3 14 12 12
___________________________________________________________
208 1 44 8 6
CT9E 360 9.0 3 25 88
240 1 38 88
3 22 10 10
___________________________________________________________
208 1 58 64
CT12E 575 12.0 3 34 88
240 1 50 66
3 29 88
___________________________________________________________
208 1 73 43
CT15 675 15.0 3 42 86
240 1 63 44
3 36 88
___________________________________________________________
*See page 2 for room sizing.
†All spec f cat ons shown are for 208V and 240V. Consult factory for other voltage spec f cat ons.
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
!WAR N ING
Provide a power supply disconnect within sight of the steam
generator or one that is capable of being locked in the open position as permitted by code.

CONTACTOR
TO PROBE
HEATING ELEMENT
MSTS
TEMP. PROBE
AUTOFLUSH
CT-STEAMSTOP
ET/PLUS
CONTROL
TRANSFORMER
POWER INPUT
L1 L2
GROUND
EXPRESS
STEAM
WATER
FEED
SOLENOID
VALVE
THERMOSTAT
THERMOSTAT
HEATER
FACT O RY
WIRI N G
FIEL D
WIRI N G
L E G E N D
(All Diagrams)
CONTROL BOARD
CONTACTOR
HEATING ELEMENT
TO PROBE
AUTOFLUSH
CT-STEAMSTOP
ET/PLUS
CONTROL
TRANSFORMER
POWER INPUT
L1 L2
FUSES
GROUND
WATER
FEED
SOLENOID
VALVE
EXPRESS
STEAM
THERMOSTAT
HEATER
FACT O RY
WIRI N G
FIEL D
WIRI N G
L E G E N D
(All Diagrams)
SINGLE P ASE WIRING DIAGRAMS with eTempo/Plus®Controls
MODEL CT12E & CT15E
MODEL CT6E & CT9E
9
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________

Maintenance
Mr.Steam steambath generators require little maintenance. Other than peri-
odic draining, maintenance procedures are minimal. Every 2 months, or
more often in “hard” water areas, when Auto lush is not installed the man-
ual drain valve should be opened fully flushing out accumulated materials,
salts and other particles which are natural by-products of boiling water.
lush a minimum of two-three hours after the control
has been turned off to insure that the water has cooled.
Draining immediately after a steam cycle may expose
PVC and other piping to high temperature water. Check local codes. The
unit will refill automatically when the control is activated again. In areas of
hard water, a Mr.Steam Auto lush system is recommended for generator
longevity.
10
Initial Start-Up and Checkout
1.Turn on control. ollow specific instructions pages 21-22 or those
provided with controls.
2.Steam will begin to appear in approximately 5 minutes (unless equipped
with factory-installed Express Steam option) at the steam head. Steam
will shut off when desired temperature is reached and will automatical-
ly resume when room temperature drops below set point.
3.Steam will shut off automatically when control counts down to zero.
To shut steam off manually, turn control O . To clear steam from
enclosure area, turn shower on before opening door.
4.If unit does not start and control does not turn ON (control display
does not light up) then turn breaker off for 20 seconds and try again.
5. Refer to specific instruction sheets for installation, operation and
maintenance of optional equipment and eTEMPO/PLUS, CT-STEAM
STOP and MSTS.
!WAR N ING
!CAU T I ON
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
FACTORY
WIRING
FIELD
WIRING
L E G E N D
(All Diagrams)
CONTACTOR
TO PROBE
THERMOSTAT
CONTROL BOARD
AUTOFLUSH
CT-STEAMSTOP
ET/PLUS
CONTROL
TRANSFORMER
POWER INPUT
L1 L2 L3
GROUND
WATER
FEED
SOLENOID
VALVE
S
C
THERMOSTAT
HEATER
EXPRESS
STEAM
G
T REE P ASE WIRING DIAGRAMS with eTempo/Plus®Controls
MODEL CT6E, CT9E & CT12E

11
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
SYSTEM STATUS CODES
The control (either eTempo or eTempo/Plus) may display a status code if the steam generator is not functioning properly.
Code Code Meaning Probable Cause Suggested Remedy
H20 Water level is not Water Supply is off Turn on Water Supply
satisfied within 5min. Defective water feed solenoid Check/replace water solenoid valve
Water feed probe not functioning Check/clean probe.
Check probe wiring.
Drain Valve Open Check/Close drain valve
Auto lush not functioning Check/Replace Auto lush
Prr1Temperature Probe Error Control cable/MSTS cable cut Replace control cable/MSTS
or Prr2Internal problem with control/MSTS Replace control / MSTS
Err1Incorrect ield Supply Voltage Incorrect voltage supplied Supply steam generator with the correct
(green light on liquid level to Generator voltage noted on the data plate label.
control board will be off)
Err2Button on control is pressed Control cover misalignment Remove and reinstall control cover
for more than 5 minutes Debris behind control cover Remove control cover and clean cover,
control and keypad with a damp cloth
Err7Liquid Level Control Board malfunction Memory error in LLCB Press ON/O to clear.
Replace control if code remains.
Transformer
Liquid Level
Control Board
Water Feed
Solenoid
Water Feed
AutoFlush Plug
and Play Connector
(see page 11)
Thermostat
Liquid
Level Probe
Power Supply
Knock-Out
Contactor
Steam Outlet
TROUBLES OOTING
Step 1 Check your main incoming power
to the unit.
Step 2 Verify the transformer is receiving
208/240 VAC.
Step 3 Verify that you have 24VAC coming
out of the transformer, WHT & WHT/BLU
wires, into the board.
Step 4 Verify that you have the green
light on the PC board.
Step 5 Push the white test button to run
the generator on a 10 minute test cycle.
Step 6 Verify that you have 24 VAC to the
water feed solenoid, GRY & WHT/GRY wires
(will fill when needed).
Step 7 Temporarily short out the WLS
(Purple wire) and GND (Green wire)
terminals and verify the contactor engages.
Step 8 When the red light is on, verify
that you have 24 VAC, RED & WHT/RED
wires, to the contactor.
Step 9 Check to see that you have your
main voltage on the load side of the contac-
tor when it is engaged.
Step 10 If all steps on the power path were
verified, turn off power to the unit and pull
the heating element via the left hand access
panel for inspection.
Do not disassemble internal components, internal components contain no serviceable parts.

12
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
AUTOFLUS ®
Box Contents
• Auto lush Valve with Cord
• Installation instructions.
Operation
The optional Auto lush System feature automatically
drains the CT system following each use.
A time delay allows the water to cool down (about
two hours) before it drains by gravity for a safe and
gentle operation. Unit drains by gravity.
Installation Instructions
1. Plumbing to be performed by a qualified plumber
and shall be in accordance with applicable national
and local codes. Unit drains by gravity. A drain line
that is lower than the Auto lush assembly must
be available. The Auto lush System valve outlet is
threaded 1" NPT. Check plumbing code for receptor,
trap and vent requirements.
2. Use copper or brass nipple 1" NPT x 31⁄2" or longer (not supplied)
to connect Auto lush valve (end "B") to the Drain Valve (valve
end “A” and “B” are indicated on bottom of Auto lush Valve)
DO NOT REMOVE THE DRAIN VALVE
Removal may cause equipment and property damage.
If there is not enough room for the valve, an elbow and
a short nipple (not provided) can be added.
3. Open Drain Valve (handle must be aligned with brass nipple).
4. Connect the Auto lush System cord connector to
the three pin connector as shown.
Do not drain into a steam enclosure or any
location where accidental contact with drain water may occur.
In the event of a power failure the Auto lush System valve will
open and may discharge boiling water.
Sweat Fittings
When using sweat fittings use only tin base solder with a melting
point below 600 degrees . Do not overheat. Ends of water supply
tubing must be thoroughly clean for a minimum distance of 1"
from ends. Do not remove valve cover.
To Check Operation
1. Turn on Mr.Steam and allow tank to fill with water.
2. Turn off Mr.Steam control. Water should stay in tank.
3. Turn off power at the panel box. Water should
discharge from tank.
4. Turn on power at panel box.
!CAU T I ON
!WAR N ING
!CAU T I ON
Drain Valve
DO NOT TURN OR REMOVE T E DRAIN VALVE
(shown in the correct open position)
Steam Generator
Nipple Plumb to
Drain Line
AutoFlush Valve
AutoFlush Cord
AutoFlush Valve
3Pin Connector
for AutoFlush
AutoFlush Cord
Connector
Drain Valve
(shown in the correct open position)
DO NOT REMOVE THIS DRAIN VALVE
Steam Generator
Nipple
copper or brass
nipple 1" NPT x
31⁄2"or longer
(not suppl ed)
End
"B" End
"A"
Plumb to
Drain Line
Arrow nd cates correct
d rect on of flow
5. Repeat
PROVIDE DRAIN PLUMBING ACCORDING TO LOCAL
CODES. PLUMB AS REQUIRED OR AUTO LUSH SYSTEM.

mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
RED (Heater)
YELLOW (Water Level)
GREEN (Power)
Force On
Test Button
DRAIN PAN
Mr. Steam provides a drain pan in the unlikely event of a plumbing leak.
Locate the drain pan on a solid level surface and place
the steam generator inside the drain pan. Insure the
steam generator is level (see page 4for locating the
steam generator).
All plumbing shall be performed by a qualified licensed plumber and in
accordance with applicable national and local codes. Check local plumbing
code for receptor, trap and vent requirements. Drain pans drain by gravity.
The drain pan is equipped with an integral 3⁄4" NPT fitting.
EXPRESS STEAM
( actory installed)
All CT models have Express Steam standard.
Express Steam is equipped with a low power heating
element and thermostat to keep the water in the tank
warm enough to bring up steam quicker. All Express Steam
components and wiring are installed at the factory. No
additional wiring or plumbing is required by installers.
LIQUID LEVEL CONTROL BOARD - Explanation of LED Indicators
_______________________________________________________________________________________________
GREEN LED is ON when there is 208/240 Volt incoming power connected,
24 Volt transformer secondary output and on-board 5 Volt DC control power are present.
_________________________________________________________________________________________________
YELLOW Water level indicator–LED is O when no water is detected (for more that 5 seconds). ON when
water level is satisfactory. or units with Auto lush, if more than five hours have elapsed since
last usage and this LED is ON it is indicative of an Auto lush or water level probe circuit malfunction.
_________________________________________________________________________________________________
RED Contactor relay indicator–LED is ON when relay is closed and sending 24 Volts to the
contactor coil. (This LED comes ON if the generator is ON.)
_________________________________________________________________________________________________
ORCE ON This button is for trouble shooting only and will operate if a control is connected or not.
TEST BUTTON Pressing the button again will shut the generator O .
The test button will only allow the generator to operate for 10 minutes.
Liquid Level Control Board PN 103975
(shown without wiring)
13

Transformer
Drain Line
Liquid Level
Control Board
Fuses
Water Inlet
Water Feed
Solenoid
Safety Valve
AutoFlush
Valve
Stainless
Steel Tank
Heating
Element
Access Cover
Thermostat
Liquid Level Probe
AutoFlush Plug and
Play Connector
(see page 11)
Power Block
Power Supply
Knock-Out
Steam Outlet
Express
Steam
Contactor
MODELS CT6E & CT9E
shown with cover removed
NOTE: FOR ILLUSTRATIVE
PURPOSES ONLY.
Some components may be
omitted or altered for clarity.
Do not use for wiring, repair
or other purposes not related to
component identification.
MODELS CT12E
shown with cover removed
NOTE: FOR ILLUSTRATIVE
PURPOSES ONLY.
Some components may be omitted
or altered for clarity. Do not use for
wiring, repair or other purposes not
related to component identification.
Contactor
Transformer
(100477-3)
Drain
Line
Liquid Level
Control Board
(103975)
Water Feed
Solenoid (100479)
Water Inlet
Safety
Valve
AutoFlush
Valve (CT81500)
Stainless Steel Tank
Heating Element
Express Steam
(104019)
Access Cover
Thermostat
(104016)
Liquid Level
Probe
(100471-2)
AutoFlush Plug and
Play Connector
(see page 11)
Power Supply
Knock-Out
Steam Outlet
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________
14
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________

15
REPLACEMENT PARTS LIST
_______________________________________________________________________
Part No. Description Product
_______________________________________________________________________
99178CT Drain Valve All models
99297 Safety Valve 15PSI All models
100479 Water eed Solenoid Valve w/filter All models
10477-3 Transformer 24VAC All models
103975 Liquid Level Control Board All models
103990-30 Cable for eTempo Control (30 ft.) All models
103990-60 Cable for eTempo Control (60 ft.) All models
MSTS-60 Remote Temperature Probe All models
100476-2 Contactor 50A 2-pole CT6E & CT9E, Single phase
99012 Contactor 50A 3-pole All 3-Phase models
103453 Contactor 50A 4-pole CT12E
100471-2 Probe Assembly All models
99096MS Heating Element Gasket All models
103938 Acrylic Shield All Models
99314 Power use 60A 250V CT12E, Single phase
29061BMS Heating Element 6 KW 208V CT6E
29061CMS Heating Element 6 KW 240V CT6E
29091BMS Heating Element 9 KW 208V CT9E
29091CMS Heating Element 9 KW 240V CT9E
29121BMS Heating Element 12 KW 208V CT12E
29121CMS Heating Element 12 KW 240V CT12E
103978-30 Cable for CT-STEAM STOP (30 ft.) All models
103978-60 Cable for CT-STEAM STOP (60 ft.) All models
104016 Thermostat All models
104015 Express Steam Thermostat All models
104019 Heating element for express steam All models
mr.steam®clubtherapy®Installation, Operation & Maintenance Manual
______________________________________________________________________________

16
mr.steam®clubtherapy®eTempo Controls
______________________________________________________________________________
ETEMPO® CONTROLS
Dimensional Information for eTempo/Plus®
BOX CONTENTS:
• eTEMPO/PLUS Control • Tube of Silicone Sealant
• Control Cable (30 ft.) • Owner’s Manual
• Steam head
Before Installing
Turn power to the steam generator O before connecting the control to the
generator. ailure to turn the power off will result in an inoperable control.
Do not use any eTEMPO/Plus, or CT-STEAM-
STOP™controls without reading and understanding the Club
Therapy steam generator Installation and Operation Manual (PUR
100426 Revision number 1.0/08 or higher). ailure to read and
understand these instructions may result in an inoperative or haz-
ardous installation.
A warning placard has been provided in the Information envelope.
This placard is to be applied to the wall of the installed shower or
steam enclosure.
Install the eTEMPO/Plus controls according to installation instruc-
tions. ailure to install according to instructions will result in an
inoperative control or hazardous overheating or inadequate heat-
ing of the steam room.
Locate the remote sensor (MSTS) in a location representative of
the desired steambathing temperatures. Do not locate the control
above or near the steam head or direct steam emissions. ailure to
install according to instructions will result in an inoperative con-
trol and overheating of the steam room.
!CAU T I ON
!WAR N ING
Do not route eTEMPO/Plus or CT-STEAMSTOP con-
trol wiring inside conduit together with power lines or close to hot
water or steam piping. Doing so may result in an inoperative or haz-
ardous installation.
Do not alter or modify eTEMPO/Plus or CT-STEAMSTOP controls. Doing
so may result in an inoperative or hazardous installation.
IMPORTANT NOTES:
• Turn power to the steam generator O before connecting the control
to the generator. ailure to turn the power off will result in an
inoperable control.
• Do not operate eTEMPO/Plus, or CT-STEAMSTOP controls with other
than a Mr.Steam Club Therapy generator. Mr.Steam Club Therapy
steam generators with serial numbers lower than 900000, or any
other brand of steam generator are not to be operated with eTEMPO
controls. Doing so may result in an inoperative installation.
• This document contains important safety, operation and maintenance
information. Leave this document with the homeowner.
Do not discard this document.
• Discontinue use of the steam generator or control if the steam
generator is damaged or otherwise not functioning properly.
Doing so may result in an inoperative or hazardous installation

mr.steam®clubtherapy®eTempo Controls
______________________________________________________________________________
17
ETEMPO/PLUS® CONTROLS
Installation Instructions for eTempo/Plus®
Step 1
Determine the desired installation location of the control.
The eTEMPO/Plus controls are designed to be installed outside the steam room
in a location only accessible by the faculty operator.
The control cable length is 30 feet. Insure that the control and/or steam gener-
ator are located accordingly. Contact a Mr.Steam technical service representa-
tive if a longer cable is required. Contact Mr.Steam for optional 60 ft. cable,
PN 103990-60
A Remote Temperature Probe Part Number MSTS-60 must be installed inside
the steam room.
DO NOT LOCATE THE CONTROL ABOVE OR NEAR THE STEAM HEAD OR DIRECT
STEAM EMISSIONS.
IMPORTANT: See installation instructions for the MSTS Temperature
Probe before rough-in or installation of control (pgs. 19-20).
Step 2 Make a one-inch diameter hole in the desired control location
(Diagram 1). Do not oversize or undersize the hole.
Step 3 Route the control cable (provided with the control) from the wall
cutout to the steam generator. Connect the black round Mini-Din connector to
the steam generator connector as shown in Diagram 2.
NOTE: The connector is keyed with the flat facing up.
IMPORTANT: Be careful not to strain, staple, pinch or otherwise
damage the control cable. Route cable as required to permit replace-
ment. Do not install cable in a metal conduit.
Step 4 irmly connect the control connector to the control. Turn on
power to the steam generator and test the control to verify correct
connections. Test per the instructions on pages 21-22. Proceed
with installation and verification of proper control function.
Step 5 Remove & discard peel-off paper to expose adhesive liner as shown
in Diagram 3.
Step 6 Run a bead of silicone (provided) as shown to the Cshaped groove
as shown in Diagram 4.
IMPORTANT: Do not apply excessive amounts of silicone. DO NOT
APPLY SILICONE TO ANY OT ER PARTS OF T E CONTROL INCLUDING T E
AD ESIVE GASKET.
Step 7 Insure the mounting surface is clean and dry as required for good
adhesion. Apply silicone into the hole in the wall as required to create a mois-
ture seal.
Hold the control with the LED display in the 12 o'clock position and press the
control against the wall until the adhesive sticks and holds firmly as shown in
Diagram 6.
IMPORTANT: Two registration marks are provided to facilitate level
installation. The marks are located at the 3 o'clock and 6 o'clock posi-
tions on the back side of the control. Use a level as required.
DIAGRAM 3
DIAGRAM 4
DIAGRAM 5
DIAGRAM 6
DIAGRAM 1
DIAGRAM 2

18
CT-STEAMSTOP™
On/Off Switch for eTempo/Plus®
DIMENSIONAL INFORMATION
Box Contents:
• CT- STEAMSTOP Control
• Owner’s Manual
• Control Cable
INSTALLING T E CT-STEAM STOP™
CONTROL
The CT - STEAMSTOP has a 30 foot cable with a Plug & Play
connector at both ends. (Diagram 1)
A 60 foot control cable is available (103978-60).
Contact a Mr.Steam technical service representative if a longer
cable is required.
The CT-STEAMSTOP must be installed inside the steamroom.
STEP 1- Diagram 2
Drill a 7⁄8inch diameter hole in a preferred wall location.
Do not oversize or undersize the hole.
STEP 2- Diagram 3
Route the cable from the wall to the steam generator. Be careful
not to strain, pinch or otherwise damage the control cable.
STEP 3- Diagram 4
Remove and discard the peel-off paper from the switch housing
to expose the adhesive as shown in Diagram 4.
STEP 4- Diagram 5
Apply silicone (provided with eTEMPO/PLUS control) to the hole in
the wall as required to create a moisture seal. Apply silicone to the
back of the switch as required to seal grout lines or as required for
additional adhesion.
IMPORTANT: Use care not to apply silicone to the
adhesive gasket.
STEP 5
Push cable and switch housing into the hole firmly.
STEP 6- Diagram 6
irmly connect the Plug & Play connector to the steam
generator connector labeled CT
- STEAMSTOP.
NOTE: The connector is keyed and will only connect
in one orientation with the tab facing up.
30' CABLE
SWITC PLUG & PLAY
CONNECTOR
DIAGRAM 1
DIAGRAM 2
DIAGRAM 3
DIAGRAM 4DIAGRAM 5
DIAGRAM 6
mr.steam®clubtherapy®eTempo Controls
______________________________________________________________________________