Msd 8728 User manual

Soft Touch Rev Control

PN 8728

Note: This Soft Touch Rev Control, PN 8728, is designed for inductive style ignition systems only. It

cannot be used with an MSD Ignition Control!

Parts Included:

1 - Soft Touch Rev Control 4 - Mounting Pads and Sleeves

4 - RPM Modules, 3,000, 6,000, 7,000, 8,000

4 - Wire Splicers

4 - Self Tapping Screws

4 - Wire Insulating Caps

Note: The RPM limit is set with plug-in rpm modules. If an rpm module is not installed, there will be

no rpm limit.

CYLINDER SELECT

The Soft Touch Rev Control comes from MSD

programmed for 8-cylinder applications. It can

easily be adjusted for operation on other en-

gines by cutting the cylinder select wire loops

(Figure 1). If the loops are cut, use the supplied

insulating caps to seal the wire ends.

MOUNTING

The Rev Control can be mounted in the engine compartment

but away from direct heat sources. It is recommended to

mount it where the rpm module is easy to access for rpm

adjustments. Make sure all of the wiring reaches their con-

nections. Once a suitable mounting location is determined

mark the location of the mounting holes by using the unit

as a template. Remove the unit and use an 1/8” bit to drill

the holes. Install the supplied mounts and use the four self

tapping screws to secure the Control (Figure 2).

WARNING: During installation, disconnect the battery cables. When disconnecting the battery,

always remove the Negative cable ﬁrst and install it last.

Figure 1 Selecting the Number of Cylinders.

Figure 2 Installing the Vibration Mounts.

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

2 INSTALLATION INSTRUCTIONS

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

WIRING

WARNING: High voltage is present on the coil terminals. Do Not touch the coil terminals or tower

when the engine is cranking or running.

Red Connects to a switched 12 volt source.

Black Connects to ground on the engine.

Green Connects to the coil negative (-) terminal.

Trigger Pickup Wires

White If the distributor is triggered by breaker points or an ampliﬁer, this wire needs to be

spliced to its trigger wire.

Violet If the distributor uses a magnetic pickup, this wire needs to be spliced into the positive

mag pickup wire.

Figure 3 Wiring to a Points/Ampliﬁer Ignition.

INSTALLATION INSTRUCTIONS 3

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

Figure 4 Wiring to a GM HEI Distributor, using the Module.

Figure 5 Wiring to a GM HEI Distributor using the Magnetic Pickup.

Note: The GM Unitized Coil, HEI Distributor was produced

with several different modules. If this installation

seems to cause a rough limit, try the wiring shown

in Figure 5 below.

4 INSTALLATION INSTRUCTIONS

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

Figure 6 Wiring to a GM Dual Connector Coil System.

Figure 7 Wiring to a Ford Duraspark Ignition.

INSTALLATION INSTRUCTIONS 5

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

Figure 8 Wiring to a Ford TFI Ignition.

Figure 9 Wiring to a Chrysler Magnetic Pickup.

6 INSTALLATION INSTRUCTIONS

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

Figure 10 Wiring to a Late Model Dodge Ignition.

3,000-3,800

4,000-4,800

5,000-5,800

6,000-6,800

7,000-7,800

8,000-8,800

9,000-9,800

10,000-10,800

11,000-11,800

12,000-12,800

13,000-13,800

PN 8743

PN 8744

PN 8745

PN 8746

PN 8747

PN 8748

PN 8749

PN 8750

PN 8751

PN 8752

PN 8753

PN 87431

PN 87441

PN 87451

PN 87461

PN 87471

PN 87481

PN 87491

PN 87501

PN 87511

PN 87521

PN 87531

PN 8670

PN 8671

PN 8672

PN 8673

PN 8674

PN 8675

EVEN

INCREMENTS

3,100-3,900

4,100-4,900

5,100-5,900

6,100-6,900

7,100-7,900

8,100-8,900

9,100-9,900

10,100-10,900

11,100-11,900

12,100-12,900

13,100-13,900

ODD

INCREMENTS

RPM MODULE KITS RPM MODULE

SELECTORS

3,000-5,200

4,600-6,800

6,000-8,200

7,600-9,800

9,000-11,200

10,600-12,800

Kits are supplied with ﬁve modules in 200 rpm increments.

RPM Selectors feature a dial that

allows you to choose between 12

different rpm limits in 200 rpm

INSTALLATION INSTRUCTIONS 7

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

Tech Notes

_______________________________________________________________________________________

Limited Warranty

M

SD IGNITION warrants this product to be free from defects in material and workmanship under its intended normal

use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date

of the original purchase. This warranty is void for any products purchased through auction websites. If found to be

defective as mentioned above, it will be repaired or replaced at the option of MSD Ignition. Any item that is covered

under this warranty will be returned free of charge using Ground shipping methods.

This shall constitute the sole remedy of the purchaser and the sole liability of MSD Ignition. To the extent permitted

by law, the foregoing is exclusive and in lieu of all other warranties or representation whether expressed or implied,

including any implied warranty of merchantability or ﬁtness. In no event shall MSD Ignition or its suppliers be liable

for special or consequential damages.

*Intended normal use means that this item is being used as was originally intended and for the original application

as sold by MSD Ignition. Any modiﬁcations to this item or if it is used on an application other than what MSD Ignition

markets the product, the warranty will be void. It is the sole responsibility of the customer to determine that this item

will work for the application they are intending. MSD Ignition will accept no liability for custom applications.

Service

In case of malfunction, this MSD component will be repaired free of charge according to the terms of the warranty.

When returning MSD components for warranty service, Proof of Purchase must be supplied for veriﬁcation. After

the warranty period has expired, repair service is based on a minimum and maximum fee.

All returns must have a Return Material Authorization (RMA) number issued to them before

being returned. To obtain an RMA number please contact MSD Customer Service at 1 (888) MSD-7859 or

visit our website at www.msdignition.com/rma to automatically obtain a number and shipping information.

When returning the unit for repair, leave all wires at the length in which you have them installed. Be sure to include

a detailed account of any problems experienced, and what components and accessories are installed on the vehicle.

The repaired unit will be returned as soon as possible using Ground shipping methods (ground shipping is covered

by warranty). For more information, call MSD Ignition at (915) 855-7123. MSD technicians are available from 7:00

a.m. to 6:00 p.m. Monday - Friday (mountain time).

MSD IGNITION • www.msdignition.com • (915) 857-5200 • FAX (915) 857-3344

FRM28768 Revised 06/07 Printed in U.S.A.

TECH NOTES

_________________________________________________________________________________________________________________________

MSD 8728 User manual

Popular Control Unit manuals by other brands