MSTRONIC SOL10D24-SW4-56B1N-IP66 User manual

MSTRONIC CO., LTD.
Features:
SOL10D24-SW4-56B1N-IP66
Solar Charge Controller + PoE Switch
With IP66 Waterproof Box
USER’S MANUAL

User’s Manual SOL10D12LFP-SW4-56B1N
Features:
Solar Input, from solar panel to charge 24V battery
Up to four outputs: four 56VDC PoE outputs(total 70W) on RJ45s
and one 24VDC output at terminal block
Active PoE Output support 802.3at handshake
Light pole mountable
IP66 waterproof
Applications:
Remote Power Systems; Surveillance, Sensors
Wireless Station; AP/Client/Repeaters
UPS Systems; Lighting, Fences, Gates
Protection:
Battery Polarity Reverse Protection
Battery Over Charge Protection
Battery Over Discharge Protection
Solar Panel Polarity Reverse Protection
Solar Panel Over Charge Protection
Output Short Circuit Protection
POE Output Short Circuit Protection

User’s Manual SOL10D12LFP-SW4-56B1N
Connection Description:
Item
Name
Descriptions
1
S+
Solar Panel Terminal: used to connect the solar panel. positive
electrode
2
S-
Solar Panel Terminal: used to connect the solar panel. negative
electrode
3
B+
used to connect the Battery positive.
4
B-
used to connect the Battery negative.
5
POE OUT/
DATA IN
SW1~SW4 Connectors: The four RJ45s are used for PoE output,
each port 56V, total 70W. work as Gigabit PoE switch (Endspan). The
RJ45s are also used for data uplink, work as Gigabit Ethernet switch.
6
Vo+ :
the DC output terminal is connecting to a device and offering power.
positive electrode
7
Vo- :
the DC output terminal is connecting to a device and offering power.
negative electrode

User’s Manual SOL10D12LFP-SW4-56B1N
RJ45 Indicators Description:
*SWITCH LED (the right indicator on RJ45)
LED
STATUS
Description
P1~P4
Green
A network device is detected (1000Mbps), but no
communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving package
from another device at 1000Mbps.
Yellow
A network device is detected (10Mbps or
100Mbps), but no communication activity is
detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off
No device is detected.
*PoE LED (the left indicator on RJ45)
P1~P4
POE OUTPUT
Yellow
A valid Powered Device (PD) is detected and
delivering power on this port.
Off
No PD is detected on this port.

User’s Manual SOL10D12LFP-SW4-56B1N
Operation Guide
1. Connect the battery to the B+ & B- terminal. Make sure the polarities are correctly
connected. Sequentially connect the solar panel to S+ & S- terminal.
2. Make sure the battery is properly connected to the unit. If no battery is connected,
then no voltage at B+ & B- terminal
3. The solar panel cannot be used stand alone without battery connected.
4. When a solar panel are connected to the charger, if the voltage of solar panel is
higher than 24V, then solar panel is of the charger.
5. DC output is connected to two separate terminals on the rear, make sure the total
draw is not over the limit, continue 3A, off @3.2 ~ 3.5A.
6. When power off /protection, the Solar input(-), and battery(-) are not on the same
grounding. Please do not connect Solar input(-) and battery(-) on the same terminal.

User’s Manual SOL10D12LFP-SW4-56B1N

User’s Manual SOL10D12LFP-SW4-56B1N

User’s Manual SOL10D12LFP-SW4-56B1N

User’s Manual SOL10D12LFP-SW4-56B1N
Specification
1.0 INPUT
1.1 Solar Panel
1.2 Input Voltage: 28V ~ 55V
2.0 OUTPUT
Model
SOL10D24-SW4-56B1N-IP66
DC Output
(rear terminal)
24V/3A*1
(as Bat. Volt.)*2
PoE Output 1
(front RJ45)
56V/0.625A
(regulated)*3
*1 continue 3A,, off @3.2~3.5A
*2 the same voltage as battery
*3 802.3at x2,or 802.3af x4
3.0 Battery Charge Types:
Solar Panel: charge current 10A maximum, depends on the solar panel.
4.0 Protection:
4.1 Battery Polarity Reverse Protection:
If only battery connected to terminal, when the battery polarities were reversed, the
model will stop output.
4.2 Battery Over Discharge Protection:
Cuts off the load when the battery voltage is lower than 20V + 0.3V, and auto
recover when the battery voltage returns to 24 V + 0.3V
4.3 Input Polarity Reverse Protection:
When solar panel or DC input polarities be reversed, the charger stop output, it
won’t damage the charger or end device
4.4 Solar Panel Charge Limit:
When charge current over 15A, the fuse will be burnt.

User’s Manual SOL10D12LFP-SW4-56B1N
4.5 Output Short Circuit Protection:
When the rear output terminal or PoE output be short circuit, protection be active,
the product stop output and auto-recover when the connector back to normal
connection.
4.6 Battery Output Current Limit:
The fuse will be burnt when battery output current over 15A
4.7 Load Output Voltage Point:
The output voltage on the rear terminal normally is the same as battery.
5. GENERAL DESCRIPTION
6.1 Operation Temperature: -40 - +60 Degree
6.2 Storage Temperature: -40 - +85 Degree
6.3 Operation Humidity: 5% - 90% with conformal coating
6.4 Cooling: Free air cooling
6.5 SIZE 88*268*207mm (W*D*H)

User’s Manual SOL10D12LFP-SW4-56B1N
6. PoE ports pin out: SOL10D24-SW4M-56B1N
RJ-45 Output (Data & Power)
Pin
Symbol
Description
1
BI_DA+
Data Pair A+
2
BI_DA-
Data Pair A-
3
BI_DB+
Data Pair B+
4
+Vdc + BI_DC+
power(+)+Data Pair C+
5
+Vdc + BI_DC-
power(+)+Data Pair C-
6
BI_DB-
Data Pair B-
7
-Vdc + BI_DD+
power(-)+Data Pair D+
8
-Vdc + BI_DD-
power(-)+Data Pair D-
option model: 12/36 Output
SOL10D24-SW4M-56A1R, 12= + , 36= -
SOL10D24-SW4M-56A1N, 12= - , 36= +