MTS Systems HIEMTPRO EMT8-2S PRO User manual

VER:1.0
B31-01-073-011
EMT8-2S PRO
USER MANUAL

~1~~1~
THIS INSTRUMENT IS FOR FITNESS ONLY
Dear user:
Thanks for using our company's products, in order to fully make use of the products,
we sincerely suggests follow:
Please read the instruction in detail and keep it well for further reading and
consulting.
It forbids others to change and maintain the machine except the professional
people.
Please do not remove and change any accessories of the machine.
Please follow the instruction to fit and operate the machine correctly.
It forbids others to open and remove the mainframe except the authorized people in
the company.
Please contact us if there is any trouble during operation.
Warning
◆◆
◆◆
◆◆
◆◆
◆◆
◆◆

~2~
Parts Introduction
Accessories
Any part of instrument made of PMMA material (for example: accessories shelf,
panel, transparent handles,etc.). Do not use alcohol or corrosive solvent to wipe clean.
work handle
Accessories frame
1
3
2
6
9
4
8
7
5
6.USB jack
9.Dust filter uet
1.Touchscreen
4.Distilled water outlet
8.Power supply line jack
5.Accessories frame
2.Distilled water inut
7.General power switch
3.Overflow

~3~
1.The distilled water should be cleared
before transportation.
2.Method:Insert the plug of silicone
tube with seal ring into socket [4] distilled water outlet.
Discharge the distilled water and shake the apparatus to
help the liquid clean out completely. And then use thumb
to press the spring, pull out the silicone tube.
Notice:While discharging the distilled water, the work
hand-rod should be placed at the handle support.
Before Transportation
2.Make sure the distilled water discharge valve[4] is closed;
3.Use special funnel to connect to distilled water inlet[2].
Insert drain pipe into overflow[3];
4.Add distilled water or deionized water from the funnel;
1.Use distilled water or deionized water;
5.Add liquid until overflow outlet;
6.Add cooling fluid successfully first time;
7.Connect power supply line[8], turn on general power
switch[7]. the recharge interface enters the interface as
(Fig 1) shows, click on “ ” to enter interface 。 Click
on “Liquid setting” to enter interface as (Fig 2) shows,
click on “ ” to become counter down 30 seconds.
8.When stopped, please observe the status of distilled
water level. add liquid until overflow outlet .then take off
the funnel. Please click the “ ”button to add liquid
again until it is full and remove the funnel.
2.When could not add into the distilled water, please
open the distilled water discharge valve[6], Add the
distilled water and observe the valve. when the liquid
is smooth outflow, blocked it and continue to fill
30seconds.
NOTE:1.Add about 1.5L distilled water or deionized,
change the water after one week.
3.If do not use the apparatus 15 days or above, we are
recommended to put the distilled water clean and clear.
Steps of Add Distilled Water

(Fig 1)
(Fig 2)

Spring

1.Clean treatment parts.
6.Puteen a bandage for user. and put in the handpiece
in. The output intensity should be regulated from low
gradually to high energy according to endurance of
customers. During operating.The beautician should
communicate with customers in time and the
customers should tell how they feel .
9.Click on “ ” to return to (Fig 1).
4.Set intensity. According to the bearing capacity of
the guests Click on “+” and “-” of “Intensity” to
adjust. The range is 1%(weak) to 100%(strong).
7.The system will pause automatically if the setting
time is over.
8.Please turn off the general power switch and unplug the
power supply line. other parts of the handle shall not be cleaned with
alcohol or other organic solvents to avoid damage to the.
2.In (Fig 1), click “AUTO” to enter (Fig 3)Select item
accord i n g to th e diff e r ent gen d e r. age an d
area(Select high medium and low according to
different parts )energy of the guests than press
“ ”to. Enter the operation interface of(Fig 4).
3.Set work time. The system default work time is 30
minutes. Click on “+” and “-” of “Time setting” to
regulate. The range is 1 to 30 minutes. Each part
about 15 to 20 minutes.
5.Click on “ ”, the system start work. If you need to
pause, Click on “ ”.
(Fig 3)
(Fig 4)
~4~
Basal Operation
2.In the interface as (Fig 1):
(2)Click on “ ” to enter operating interface.
(1)Click on “ ” to select language,。 Attention: The
“Advanced setting” is only for manufacturer,
Users do not use.
1.Insert the plug of Power supply line into [8] socket,
turn on Power switch [7]. the recharge interface
enters the interface as (Fig 1) shows.
