Multi-Mover XXL 15 TO User manual

MULTI-MOVER XXL 15 TO
1
USER MANUAL and PARTS LIST
MULTI-MOVER XXL 15 TO
Transport
* Only use stable loading surfaces with sufficient loading capacity (see section 2.2).
* Secure the MULTI-MOVER XXL 15 TO against tilting or sliding.
* It is prohibited to;
- get under the MULTI-MOVER XXL 15 TO while lifting
- remain within the tilting range of the MULTI-MOVER XXL during unloading
[jjo165]

MULTI-MOVER XXL 15 TO
2
Contents
Chapter 1 INTRODUCTION / WARRANTY / DEFINITIONS /
SAFETY SYMBOLS 3
Chapter 2 TECHNICAL DESCRIPTION 4
2.1 Designation, identification and description 4
2.2 Technical information and dimensions 4
2.3 Packaging, loading / unloading, towing, recycling 4
Chapter 3 SAFETY REGULATIONS 5
Chapter 4 PREPARATION 8
4.1 Application 8
4.2 Operator 8
4.3 Responsibility operator 8
4.4 Inspection prior to putting into operation 9
Chapter 5 USE 10
5.1 General 10
5.2 Regulations for use 10
5.3 Operation 11
5.4 Batteries 12
5.5 Coupling trailer(s) 13
Chapter 6 MAINTENANCE 14
6.1 Inspection 14
6.2 Lubrication and maintenance diagram 14
6.3 Cleaning 14
6.4 Taking out of operation 15
6.5 Annual maintenance 15
Chapter 7 ENVIRONMENT 15
Chapter 8 FAILURES 16
Chapter 9 PARTS 16
Chapter 10 DECLARATION OF CONFORMITY 17
Appendix I Electrical circuit diagram
Appendix II User manual battery charger
Appendix III Part List
Multi-Mover Europe B.V.
www.multi-mover.eu
T [phone] F [phone]
[phone]

MULTI-MOVER XXL 15 TO
3
1 INTRODUCTION / WARRANTY / DEFINITIONS / SAFETY SYMBOLS
You have made the right decision, by purchasing the Multi-Mover XXL 15 TO. You are now in the pos-
session of an excellent tool that has been constructed and produced with the greatest care. You will
profit the most from this investment, if you carefully observe the safety, user and maintenance in-
structions provided in this user manual.
The user manual should be made available to the user of the Multi-Mover XXL 15 TO and must be
present at the Multi-Mover XXL 15 TO when it is being used. The user manual must have been read
by anyone working with/at the Multi-Mover XXL 15 TO, and the instructions must be observed.
Warranty
Multi-Mover Europe BV will not assume responsibility for the goods it produced and the services it
supplied. Warranty can only be claimed if the client has made an immediate complaint and Multi-
Mover Europe BV has been given the opportunity to investigate the complaints and correct possible
faults. Multi-Mover Europe BV provides a warranty on its products in relation to materials and con-
struction defects. In case of defects as described above, Multi-Mover Europe BV shall undertake to
provide the parts manufactured by them for free, within the period of one year after delivery.
To occasions, different warranty conditions apply. Multi-Mover Europe BV will not be liable for dam-
age and indirect damage as a result of natural disasters, operational errors, lack of skilful mainte-
nance and any other use than described below.
The liability of Multi-Mover Europe BV will also terminate as soon as you or a third party performs
work, such as adaptations or extensions, to the machine, without our written permission.
The warranty conditions only apply if a defect, after investigation by the manufacturer, is recognized
as such.
At Multi-Mover Europe BV we continuously try to improve our products and service. That is why we
reserve the right to change the specifications stated in this user manual at any required moment and
without prior notice.
Definitions
In this user manual we use the following definitions;
Operator: The person who drives, controls and supervises the operation of the
Multi-Mover XXL 15 TO and is able to start and stop it, etc.
It is the company's responsibility to make sure that the operator is suffi-
ciently trained.
Dangerous areas: The area surrounding the Multi-Mover XXL 15 TO where people may get
injured.
Maintenance mechanic: The person who is completely familiar with the Multi-Mover XXL 15 TO, is
able to adjust the safety devices and to maintain the Multi-Mover XXL 15
TO.
The maintenance mechanic is familiar with the functionality’s, safety
standards and was trained to maintain the Multi-Mover XXL 15 TO. It is
the company's responsibility to make sure that maintenance staff has
been sufficiently educated and trained.
# Oprional different

MULTI-MOVER XXL 15 TO
4
Safety symbols
On various places on the Multi-Mover XXL 15 TO you will find standardised safety symbol
stickers as displayed to the right.
The upper part warns against a general or particular hazard.
The lower part indicates what type of hazard is being warned against and will explain what
you must do.
2 TECHNICAL DESCRIPTION
2.1 Designation, identification and description
Designation : MULTI-MOVER XXL 15 TO
Identification : type plate on the encasing
Description : vehicle on two drive wheels and a swivel wheel
: suitable as towing device, optionally provided with an upward and downward mov-
ing coupling point, for instance, in order to couple the pole of a trailer and possibly to
lift it.
: drive while walking, by using the driving switches on the steering handle
Accessories
The following parts are delivered separately with the vehicle:
The vehicle's operation manual
Battery Charger and Manual
Manuals for possible options
2.2 Technical information and dimensions Multi-Mover XXL 15 TO standard version
___________________________________________________________________________
PUSH AND PULL FORCE 15,000 KG
-Weight 1,550 kg
-Length 140 cm
-Width 96 cm
-Height 72 / 140 cm
-Engine power 4kW 36VDA, maintenance-free
-6 x 6-volt 240 Ah battery pack, maintenance-free, AGM lead acid
-Charger 36 volts, high frequency 20A, 200A/5H
-Push and Pull 15,000 kg or 9,900 newton horizontal traction
-Solid-rubber tire 10 cm wide SC20 Continental, 8-inch rims
-Ergonomic tiller head with emergency stop, belly button
-2 Potentiometer, of which 1 continuous setting and 2 pre-sets to 5 km/h
-Speed reduction system in case excessive cornering speed
-Inching forwards/backwards
-Emergency stop switch on the housing
-Emergency stop on Tiller head (vertical position)
-Steerable Tiller head with double castors ∅250 mm
-Maximum axle load 2500 kg
-Battery, hour and error display
-Lock with 2 keys
-Horn
-Minimum speed is 0.1 km/h (#)

MULTI-MOVER XXL 15 TO
5
-Bolt coupling (#)
-M14 coupling thread at various heights for couplings (#)
-Work area: 6 to 8 km
-Operating time: 3-4 workdays
Always supplied with 6 batteries (in the drive box), external charger and coupling. There are many
options to choose from.
2.3 Packaging, loading / unloading, towing, recycling
Packaging
The Multi-Mover XXL 15 TO is secured with straps on support beams on a pallet, surrounded by a
protective cardboard box.
Removing the packaging
Remove the clamping strips at the wheels.
Avoid injury and damage as a result of incorrect placement of the lift truck's lift forks.
Loading and unloading
If the Multi-Mover XXL 15 TO has to be moved by means of a lift truck, the lift forks must be placed at
the heaviest part at the rear of the Multi-Mover XXL 15 TO, between the 2 large wheels.
Towing
Caution! Avoid serious damage to the drive, the Multi-Mover XXL 15 TO may only be moved or towed
if the Electric magnetic brake inside the engine box on the engine has been released.