Multitone Ekotek User manual

www.multitone.com

Multitone Electronics plc

EkoTek Hub

Quick Guide

9261-9210 EkoTek-Hub/2WHUB/Issue 1 2 of 11

EU Declaration of Conformity In Accordance With Article 6.3 of the EU Radio &

Telecommunication Terminal Equipment R & TTE Directive 99/5/EC &

RoHS Directive 2011/65/EU (Decision 768/2008/EC Annex II, Module A)

As the manufacturer, we declare under our sole responsibility that the EkoTek 2WHUB

equipment in its various forms, conforms to all the applicable essential requirements of the

EU Directive 99/5/EC, in accordance with the procedures of Annex II of the Directive and the

following technical standards:-

ETSI EN 300 440 v1.3.1; ETSI 300 440-2 v1.1.2 (Directive article 3.2);

ETSI EN 489-1 v1.9.2; EN 489-3 v1.4.1 (Directive article 3.1{b});

EN 60950 (Directive article 3.1{a}).

This equipment is designated as a Class 1, Sub Class 21 (non-specific short range device)

under the terms of the Directive and TCAM (Telecommunication Conformity Assessment

and Market Surveillance Committee) classification scheme.

This equipment is manufactured to meet the RoHS Directive 2011/65/EU restricted

substance thresholds and does not make use of any exemptions.

A full copy of the Declaration of Conformity may be obtained from www.multitone.com, or

upon application to Multitone.

FCC & Industry Canada Statement of Compliance

This device complies with Part 15 of the FCC Rules and Industry Canada Standards RSS

GEN & RSS210. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference and (2) this device must accept any interference that may cause

undesired operation.

Unauthorised modification to this equipment will void the user's authority to continue to

operate the device within the scope of the Industry Canada and FCC Part 15 Rules.

Cet appareil est conforme au(x) standard(s) RSS exempt(s) de licence d’Industrie Canada.

Son fonctionnement est sujet aux deux conditions suivantes: (1) cet appareil ne doit pas

occasionner d’interférence et (2) cet appareil doit supporter toutes les interférences, y

compris celles qui pourraient provoquer un mauvais fonctionnement de cet appareil.

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as

household or general waste. It should be handed over to the applicable

collection point for the recycling of electrical and electronic equipment, or

returned to Multitone or their agent, for disposal.

9261-9210 EkoTek-Hub/2WHUB/Issue 1 3 of 11

EkoTek Hub

Buttons (from left to right):

Navigation keys: left arrow, down arrow, right arrow.

Red button: emergency alarm.

Turning on the device

•To switch the hub on, insert the power supply into the back of the hub.

•Insert back-up batteries.

•Ensure isolator switch is in the correction position.

9261-9210 EkoTek-Hub/2WHUB/Issue 1 4 of 11

Display

Status Icons

The following icons are displayed in the top right corner of the display as status indicators:

Plugged in to power source:

Running on back up battery:

Audible alert:

Shift mode: day shift: night shift:

Screen display

11:34 12.03.07

Hub [1234567]

EkoTek

Name / Message status

9261-9210 EkoTek-Hub/2WHUB/Issue 1 5 of 11

Raising and clearing alarms

•When an alarm is raised a text message is sent to configured group of pagers.

•The text includes the raising device’s identity, the alarm type that has been activated

and the location of the device. Fixed devices report their identity and alarm type only.

•On clearance of an alarm, a text message is sent with the device’s identity stating the

alarm has been cleared.

•Upon receiving a message, the device will sound an alert and activate the backlight

(depending on profile settings) and the message will be displayed.

•An external klaxon or lamp can be connected and will remain activated until all open

alarms are cleared, unless one of the three navigation buttons is pressed.

Emergency Alarm (red button): (if enabled)

•Single click or double click, (depending on configuration) raises an emergency alarm.

•The alarm is sent out to the pagers/users configured by the administrator.

•Use the ◄button to clear the alarm.

•The alarm will be re-sent at an interval configured by administrator, until the alarm is

cleared.

9261-9210 EkoTek-Hub/2WHUB/Issue 1 6 of 11

Receiving Messages

Receiving a message

•The new message will display on the screen.

•Message actions:

oSelect the ▼button to see the available responses (accept and reject or

delete).

oUse the▼button to scroll to the desired option .

oSelect the Xbutton to send the response or delete the message.

oAccept responses will be sent to the user that raised the alarm, to show that

help is on its way.

Message Overview Screen

•After display time-out, the screen returns to the message overview screen.

•The first part of each message is shown in a list format.

•Use the ▼button to scroll through the messages.

•Use the Xbutton to display the full message.

9261-9210 EkoTek-Hub/2WHUB/Issue 1 7 of 11

Hub Functions

•Use the ▼button to scroll to hub functions

•Press the ►button to select

i. Day/Night

From the functions screen:

•Use the ▼button to scroll to Day/Night

•Press the ►button to select the option

•Press the ▼button to toggle between Day/Night

•Press the ►button to select the required option

ii. Time

•Use the ▼button to scroll to Time

•Press the ►button to select the option

•Use the ▼button to increase the hours to the desired time

•Press the ►button to select the minutes

•Use the ▼button to increase the minutes to the desired time

•Press the ►button to confirm the time

•After a short delay the time displayed in the standby screen will show the new time

iii. Date

•Use the ▼button to scroll to Date

•Press the ►button to select the option

•Use the ▼button to increase the day to the desired day

•Press the ►button to select the month

•Use the ▼button to increase the month to the desired month

•Press the ►button to select the year

•Use the ▼button to increase the year to the desired year

•Press the ►button to confirm the date

•After a short delay the time displayed in the standby screen will show the new date

ZDay/Night Night

Time 05:33

Date 09.01.13

IP Address

9261-9210 EkoTek-Hub/2WHUB/Issue 1 8 of 11

iii. IP Address

•Use the ▼button to scroll to IP address

•Press the ►button to select

•Press the ►button to confirm

•The standby screen then appears and the IP address of the hub is displayed after a

short displayed after a short time as a message

•This can be deleted as per a standard message.

9261-9210 EkoTek-Hub/2WHUB/Issue 1 9 of 11

Advanced Settings

•Use the ▼button to scroll to Advanced.

•Press ►button to select the option.

•Use the ▼button to scroll to the desired option:

a) Display

•To select, press ►from the Advanced menu options.

Navigation Instructions

For ALL the following options:

•Use the ►button to select the option

•Use the ▼button to scroll between options

•Use the ►button to select the required option

•Use the ◄button to return to the display menu

•Use the ◄button again to return to the main menu if desired

i. Hour Mode

•Available options: 12H and 24H.

ii. Display Time-out

•Available options: 8, 16, 32 and 64 second time-out.

iii. Font

•Available options: 7 x 5, 10 x 5, 10 x 8 formats (only applicable to message display).

iv. Contrast

•Available options: scroll between 0 to 5.

ZDisplay

Custom profile

Hide clear info Off

Hour Mode 24H

Display Timeout 16s

Font 10 x 5

Contrast 2

9261-9210 EkoTek-Hub/2WHUB/Issue 1 10 of 11

b) Custom Profile

•Use the ▼button to scroll to Custom profile.

•Press ►to select this option, where upon the following options are displayed.

•See 3.a) for how to navigate and select options.

i. Backlight

•Use the ▼button to scroll to backlight.

•To turn the backlight on/off:

•See navigation instructions for how to select options.

ii. Audible alert

To turn the audio alert on/off:

•See navigation instructions for how to select options.

c) Hide Clear Info

•The ‘clear alarm’ instruction can be displayed on the screen to show users how to

clear a raised alarm.

•To hide this information the ‘Hide Clear Info’ function can be turned on.

•See navigation instructions for how to select options.

ZBacklight On

Audible alert On

Display

ZCustom profile

Hide clear info Off

FM 20122

Multitone Electronics plc, Multitone House, Shortwood Copse Lane, Kempshott, Basingstoke, Hampshire, RG23 7NL

Telephone: +44 (0)1256 320292 Fax: +44 (0)1256462643 Email: [email protected] Web: www.multitone.com

This document is for guidance only. Products and services offered are subject to availability and may differ from those described or illustrated in this

document as a result of changes. Specifications are subject to change without notice. Multitone Electronics plc is part of Kantone Holding Ltd, a member