MUNBYN IPDA074 User manual

IPDA074
Handheld Terminal
User Manual

Content
Chapter 1 Device layout ....................................01
1.1 Installing the SIM Card .................................................03
1.2 Installing the SD card ....................................................03
1.3 Installing the battery ......................................................05
1.4 Removing the battery ....................................................06
Chapter 2 Charging the Battery .........................08
2.1 Charging time ................................................................08
2.2 Charging temperature ....................................................08
2.3 Battery power supply .....................................................08
2.4 Notes for battery use ......................................................08
2.5 LED Indicators ..............................................................09
Chapter 3 Typical applications introduction .....09
Chapter 4 Troubleshooting ...................................38
3.1 Scan tool ........................................................................09
3.2 Mobile butler .................................................................14
3.3.1 Import ..........................................................................24
3.3.2 Export ..........................................................................26
3.4 Features setup ................................................................28
3.5 Certificate Whitelist .......................................................31
3.6 Shortcut Key settings .....................................................34

01
Chapter 1 Device layout
Figure1-1 Front view

02
Figure1-2 Front view of 22 keys
Figure1-3 Back view

03
Figure1-4 Installing the SIM Card
Please install the SIM card as instructed below:
1.1 Installing the SIM Card
Please install the SD card as instructed below:
Insert the SD card in the direction shown in the figure below (micro
SD or microSDHC).
1.2 Installing the SD card
Figure1-5 Installing the SD Card

04
Slide the battery cover switch to the right side to unlock
Pull out the battery cover
1.3 Installing the battery
Figure1-6 Remove the battery cover
Note: 1. PSAM card is not supported.
2. The device does not support the card hot plug, please reset after
accident hotplug.
Install the battery into the battery cassette at a right angle.
Please make sure the battery is well connected and press it down.
Figure1-7 Install the battery

05
Figure1-8 Lock the battery
Slide the battery lock upward to lock the battery.
Put the battery cover back right into the slot.
Press it downward and lock the cover.
Figure1-9 Put the battery cover back

06
Slide the battery cover lock to unlock (the right side)
Remove the battery cover.
Removing the battery follow the instruction as below:
1.4 Removing the battery
Slide the lock to the left side to lock the battery cover.
To be transported or to be spared for a long time, please remove
the battery and store the device and the battery separately.
Figure1-10 Lock the battery cover
Figure1-11 Remove the battery cover

07
Slide the battery lock downward to loose the battery
Remove the battery
Figure1-12 Unlock the battery
Figure1-13 Remove the battery

08
Battery: It takes about 3.5 hours to charge the battery for the first
time through the adapter. The LED light will stay red when charging,
and when the battery is full, the LED light will start to stay green.
2.1 Charging time
The best operating temperature is room temperature 18~25℃.
The battery cannot be charged with the temperature lower than 0℃
or higher than 50℃.
The battery cannot be charged with the temperature lower than 0℃
or higher than 50℃.
2.2 Charging temperature
Using WI-FI service or data collection program will consume more
battery power than normal, please keep them off to save power
when you are not using the internet.
In order to avoid any inconvenience, it might cause you for battery
depletion, having a backup fully charged battery or connect the
device with power supply while working are highly recommended.
Note: If you do not use the product for a long time, please charge
the device at least once every two months.
2.3 Battery power supply
If the new device does not turn on, please make sure the insulation
sticker on battery has been removed.
If the battery is completely discharged, the device can’t be turned
on immediately. This is a normal phenomenon. Allow the depleted
device to be charged for a few minutes before power it on.
2.4 Notes for battery use
Since the battery only has a small amount of power for testing when
it leaves the factory, so please charge it before using it.The IPDA074
series device can also be charged with USB cable, device charging
dock and specified extended interface charging cradle.
Chapter 2 Charging the Battery

09
Note: When the system is in charge, the blue indicator light will not be on.
Without the insertion of USB and charging adapter, the red light
flashes to indicate that the battery power is too low, please charge
it in time;
With insertion of USB cable and charge adapter, long bright red
flashes to indicate that the battery is under charging.
With insertion of USB cable and charge adapter, long bright green
flashes to indicate that the battery is fully charged.
If the LED indicator on the right side of the device flashes blue just
like the breathing light, it indicates that there’s a an unread message.
Please check it in time.
The LED indicator, in the middle of the top right of the device, indicates
the battery and charging status by flashing different colors:
When a bar code is successfully read, the LED indicator flashes red once.
Otherwise, there won’t be any LED flash.
2.5 LED Indicators
The battery can be charged repeatedly, but the battery is a consumable
product. Please replace a new battery if you find the device's standby
time is greatly reduced.
Battery charging time changes with temperature and battery usage.
Please charge it at a reasonable temperature range.
When the battery is in low power, the device will give a low-power
warning. When the battery power is too low, the device will
automatically shut down.
Chapter 3 Typical applications introduction
3.1 Scan tool
1. Find this icon , tap it to enter the interface shown below and invoke
the scan function.

10
Figure3-1 Home screen of scan tool
Figure3-2 Barcode
2. Select Barcode and enter the barcode type setting interface. Set the
barcode type you need.

11
Figure3-3 Basic settings
3. Open the basic settings to set the parameters including Duration,
Scanning angle, Time-out, Continuous scan, etc.
4. Open Application Settings to set the basic scan switches:
Sound: Give you a voice prompt while scanning.
Scan light indicator: The red indicator will light up after successfully
decoding once the function is activated.
Vibrate: Give you a vibration tip while scanning.
Append: Continuously output barcodes.
Auto clear: Automatically clear the last barcode before the next barcode
scanning starts.
Booted start: Automatically turn on the Scan tool when booting up.
Show type: Display the barcode type while scanning.
Filter invisible char: To filter the invisible char in barcodes.
Filter pre/suffix blanks: To filter the blanks when it’s as prefix or suffix.
Stop scan on up: Loosen scan button and the scan lighting immediately
turns off, or press scan button and the scan lighting continues for a certain
time range (set Scan duration ) before turning off.
1
2
3
4
5
6
7
8
9
10

12
Figure3-4 Applications settings
Loop count: To count and display the scan loops and sum the successfully
decoded or undecoded barcodes.
Loop scan: Automatically scan barcode continuously. if switch on
continuous lighting mode in Basic settings and then scan with continuous
lighting.
Interval: Set time delay between two scans.
Restore the barcode default settings: you can restore the barcode default
settings, as shown in Figure 3-5.
Barcode suffix: Add barcode output suffix on your own (They can be
numbers, letters, special characters, etc.).
Barcode prefix: Add barcode output prefix on your own (they can be
numbers, letters, special characters, etc.).
End Char: you can choose the barcode to end the output, including:
Enter, Tab, Space, None.
Code character: To select the output code character of the barcode,
including AutoDetect, Raw, GBK, GB2312, UTF8, BIG5, SJIS,
EUC_JP, ISO8859_1, and by default as AutoDetect
Barcode Send Mode: Select Focus, Broadcast, EmuKey or Clipboard
to send (Emukey needs the input which supports the hard keys), as
shown in Figure 3-6. End Char can be selected to send over keys in the
focus input mode.
Developer: Input password 888888 and then developer options can be
modified (not recommended).
Note: The advanced interface entry password is 4007770876 .
11
12
13
14
15
16
17
18
19
20

13
Figure3-5 Restore barcode
default setting
Figure3-6 EmuKey settings
Figure3-7 Developer

14
Figure3-8 Hide and Exit
Figure3-9 Default launcher setting
3.2 Mobile butler
This application is designed for the customers to set up access rights of
Android portable terminals according to their own needs and to prohibit
users from accessing non-designated applications.
1. Go to Settings -->then to Application and Notification, and then
the Default Application to Home Screen Application, tap to select Mobile
butler as shown in the figure below:
5. Hide and Exit applications
Tap Hide: the application will run in the background and scanning can
be enabled by pressing the scan button on any editing interface.
Tap Exit: exit and close the application.
1
2

15
Figure3-10 No password set interface
As shown in the figure above, the administrator password is not set.
Please tap Confirm to enter the password set interface as shown below:
Open the application and briefly press Menu button to add items to the
desktop.
1
2. Administrator settings and change password

16
Note: Please do not leave the password empty, and the newly-set password
shall be same as it in the double check input text.
Figure3-11 Initial password setting
Et the administrator's initial password as required, e.g. 123456, then tap
confirm to complete the setting.
Briefly press the Menu button again, as shown in the figure below:
1

17
Figure3-12 Password input interface
Enter the administrator password (123456). You can pass the verification
and then enter the interface in the figure below: