Murphy EVS-2 User manual

00-02-0841
2013-01-14
Section 20
EVS-2
ElectronicVibrationSwitch
Installation and Operations Manual

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our
specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com.
Warranty –A limited warranty on materials and workmanship is given with this FW Murphy product.
A copy of the warranty may be viewed or printed by going to http://www.fwmurphy.com/warranty.
Please read the following information before installing the EVS-2.
This installation information is intended for all EVS-2
models. A visual inspection of this product before
installation for any damage during shipping is
recommended.
Disconnect all power and be sure machine is inoperative
before beginning installation.
Installation is to be done only by qualified technician
according to the National Electrical Code.
Observe all Warnings and Cautions at each section in
these instructions.
Please contact FW MURPHY immediately if you have any
questions.
FW MURPHY has made efforts to ensure the reliability of the Electronic Vibration Switch (EVS-
2) and to recommend safe usage practices in system applications. Please note that in any
application, operations and device failures can occur. These failures may result in full control
outputs or other outputs which may cause damage to or unsafe conditions in the equipment or
process connected to the EVS-2.
Good engineering practices, electrical codes, and insurance regulations require that you use
independent external protective devices to prevent potentially dangerous or unsafe conditions.
Assume that the Murphy EVS-2 system can fail with outputs full on, outputs full off, or that other
unexpected conditions can occur.

Table of Contents
Product Information...................................................................................................................1
Murphy EVS-2 Overview..............................................................................................1
EVS-2 Characteristics and Orientation.........................................................................2
Installation...................................................................................................................................3
Mounting ......................................................................................................................3
Mounting Options.........................................................................................................4
Bracket Proposals........................................................................................................5
Mounting Examples......................................................................................................5
Plug Options.................................................................................................................6
Wiring...........................................................................................................................6
Settings......................................................................................................................................10
Setting the Set-Point in Inches Per Second (IPS) Peak.............................................10
Setting of Alarms........................................................................................................13
Vibration Limits Based on Class of Equipment Based on ISO 10816-3.....................14
Equipment Manufacturer Recommended Settings.....................................................16
Specifications...........................................................................................................................17

THIS PAGE INTENTIONALLY LEFT BLANK

Section 20 00-02-0841
2013-01-14 - 1 -
Product Information
Murphy EVS-2 Overview
The Murphy Electronic Vibration Switch (EVS-2) protects against equipment failure by
monitoring velocity-based vibration levels and providing an early warning or shutdown when
abnormal vibration is detected. The EVS-2 can be connected to Murphy’s TTDannunciator,
Centurion, Centurion PLUSor any third- party controller that accepts a switch input or 4-
20mA signal for increased functionality.
NOTE: The Murphy EVS-2 complements Murphy’s VS2shock and
excessive vibration switch, which is designed to detect an abnormal shock
due to equipment failure and to shutdown other equipment in a system to
prevent further damage.
Features
Universal use, can be mounted horizontal, vertical or at any other angle
Piezoelectric-crystal internal sensor with built-in microelectronics for reduced noise
sensitivity
Electronically integrated output signal that measures and trips on velocity (IPS peak)
Two independently adjustable output channels
Shutdown setpoint measured in velocity (IPS peak)
4-20 mA output for continuous monitoring capability
Solid-state outputs for setpoint trip
Adjustable time delay to prevent false tripping on high-vibration start-ups or non-
repetitive transient events
RAW 100mV/g output also available
Applications
The Murphy EVS-2 can be used on any
equipment where abnormal vibration could
lead to equipment damage, including:
Cooling fans
Engines
Pumps
Compressors
Gear boxes
Motors
Generator sets
The Murphy EVS-2 can monitor and alert the
operator of abnormal vibration caused by a
variety of possible factors, including:
Imbalance
Misalignments
Worn sleeve bearings
Broken tie down bolts
Worn ball or roller bearings
Gear mesh
Blade pass frequencies
Detonation
Broken parts

Section 20 00-02-0841
2013-01-14 - 2 -
EVS-2 Characteristics and Orientation
To prevent damage to the EVS-2 vibration switch, the following vibrations may not be
exceeded:
Vibration 15 g
Shock 150 g
Two-Channel LED Indicators
Two independent, adjustable level detectors with selectable delay times are equipped with
corresponding relays which are typically used for Alarm and Shutdown. Both channels use the
same vibration range selection.
Red and Yellow LED indicators representing these two channels are illuminated during normal
use. When a fault is activated, the LED indicators will turn off.
IMPORTANT! Because the EVS-2 resets automatically when the
vibration level returns below the set point, it is important to ensure
that the fault has been addressed before restarting the equipment.
1
Red Channel 2 LED (K2)
2
Spring terminal 16-24 AWG.
3
Channel 2 (K2) Vibration Set Point
Potentiometer (Pot)
4
DIP switches for vibration ranges and time
delays.
5
Channel 1 (K1) Vibration Set Point
Potentiometer (Pot)
6
Yellow Channel 1 (K1) LED
Figure
1
–Inside view of Murphy EVS-2 component locations

Section 20 00-02-0841
2013-01-14 - 3 -
Installation
Mounting
The Murphy EVS-2 must be mounted and set in accordance with the guidelines in this manual
to obtain the desired and specified performance and equipment protection.
Mounting occurs via a ½” NPT thread, the tightening torque is hand tight plus 2 to 3 turns.
When using a mounting bracket, ensure that mounting surfaces are smooth and flat.
Care must also be taken that the mounting surface is not subject to natural vibrations. Using a
high stiffness mounting surface prevents natural vibrations which cause measurement errors.
WARNING! Exceeding the torque specification will damage the
aluminum housing. If there is concern of the device becoming
loose due to excessive vibration, use a permanent thread locker
such as Loctite 271 (RED).
Figure
2
–Product Dimensions and Sensitivity Axis

Section 20 00-02-0841
2013-01-14 - 4 -
Mounting Options
The following diagrams illustrate example mounting options for the EVS-2 using a simple pipe
plug welded to the machine surface or a bracket with the special adapter provided for drilled
and tapped surface mount.
NOTE: The special adapter is available for sale. Also note that a hollow
pipe close nipple is NOT recommended for installations.

Section 20 00-02-0841
2013-01-14 - 5 -
Bracket Proposals
Mounting Examples
Legend: C=Compressor, E=Engine
Compressor
Cx (Compressor) = Crankshaft endplay
Cy = Main Bearings, Rod Bearings
Cz = Main Bearings
Engine
Ex (Engine) = Crankshaft endplay
Ey = Main Bearings
Ez = Main Bearings, Detonation, Rod Bearings

Section 20 00-02-0841
2013-01-14 - 6 -
Plug Options
High-pressure (non-hollowed), forged steel pipe
plug permanently welded to equipment or
bracket surface. Be sure weld is clear of
threads for maximum thread engagement.
Optional Adapter available from FW Murphy:
½” NPT, High-pressure (non-hollowed), steel
pipe plug, Male x Male to be used for direct
mount to equipment with a ½” NPT threaded
pilot hole.
Wiring
The method chosen to electrically connect to the switch should be mechanically flexible to
eliminate the measurement of vibration induced from conduit and to provide a moisture barrier
as well. Although Sealtiteand other flexible conduit have been used successfully, in areas of
extreme humidity or moisture Murphy recommends using an “SO” type cable along with a Div.
2 suitable rain-tight CGB Gland/Strain relief fitting. No stress should be possible on the wiring
to the terminal block. If such protection is not provided by the conduit system, some form of
stress relief must be installed.
WARNING! Certification compliance requires the use of a cable
gland and strain relief fitting.
To assure compatibility with EMI compliance standards, any signal level wiring such as
transducer or 4-20 mA wiring should use shielded cable in EMI proof conduit, separate from
any power wiring except the DC power for the EVS-2. AWG 16-26 wire can be used.
NOTE: It is strongly recommended that this cabling be installed using the
method defined in the Shipboard Cable/Cord Installation document (00-
02-0725 rev 08/2010). That document can be found by following this link
http://www.fwmurphy.com/evs-2.