musikelectronic geithain rl906 User manual

musikelectronic geithain
Studio Loudspeaker
RL 906
Instruction Manual

Introduktion
Dear customer,
congratulations with the purchase of our active loudspeaker system.
The RL906 loudspeaker is equipped with a 125-mm cone woofer and a
coaxially positioned 25-mm tweeter callote.
The basic principals of all RL-series active loudspeakers are the active multi-
way technology with integrated analogue crossovers and power amplifiers, as
well as the implementation of our special coaxial technology. The result are
loudspeakers which are unparalleled with respect to focus accuracy, depth
perspective and distortion characteristics. Audio-physiological aspects were
crucial for optimising the directivity index. The active loudspeaker is
magnetically shielded; this allows a position close to a TV set.
Our active loudspeaker system can be connected to any pre-amplifier
(U >1 volts R < 600 ohms).
Please carefully attend to the safety instructions!
This product complies with the requirements of the applicable European
and national directives (Electromagnetic Compatibility 89/336/EWG). The
conformity was proven; the respective declarations and documentation
are deposited with the manufacturer.
In order to maintain its excellent condition and to ensure a safe operation,
please carefully read and attend to this instruction manual.
Included in Delivery
Speaker
Line Cord
Instruction Manual

Safety Instructions
As with other electrical equipment, you must attend to the following basic
operational and safety instructions, as well as to warning notices, in order to
ensure optimal functionality and operational safety of the system!
�For safety reasons, unauthorized alterations and/or modifictions of the system are
not allowed.
�Keep children away from electrical equipment.
�The device must only be operated with the mains voltage indicated on the reverse
side.
�If the device is installed into a shelf, rack or wall cupboard, please ensure sufficient air
circulation.
�Do not Never insert any objects into device openings.
�Do not allow any liquids to get inside the unit.
�Danger of electric shock if cabinet is opened.
�Repairs must be carried out by qualified personnel only.
�For cleaning, please use a damp cloth only.
�Do not use flue gas scrubber or spray cleaners.
Unpacking
The loudspeaker has been delivered in a sound condition. Carefully unpack the
loudspeaker and check it for visible damages. Please contact your dealer immediately
in case of damage. Please keep the packaging for possible future transports of the
loudspeaker.
Cleaning
The loudspeaker surface is of wood veneer and should be treated similar to furniture.
We recommend using a quality wax polish for protecting the veneer and keeping it
glossy. You can also use a clean damp, soft and lint-free cloth for cleaning the
surfaces.
Installation
Please do not expose the loudspeaker to direct solar irradiation. Neither set up the
loudspeaker in rooms with high air humidity.
Warranty notes
Any warranty claims expire, if the device has been opened by un-authorized
personnel. No warranty exists if the device is destroyed due to overload, improper
manipulation or extraneous cause.

Hörzone
>0,5m
>0,5m RL906
RL906
Hörzone
RL906
>1,00m <2,60m
60°
RL906
>1,00 m
Hörzone
1,0-1,2m
Arrangement
The optimal positioning of your loudspeakers can considerably contribute to a good listening
impression in your room.
Stereo Operation
The optimal position is the so-called stereo triangle. The base distance between the
loudspeakers and their distance to the listening zone should form an equilateral triangle
(stereo triangle). The distances should be at least 1.0 m and should not exceed 2.6 m.
For a precise spatial image, turn the loudspeakers slightly inwards in the direction of the
listening zone.
The mounting height should be adjusted to the listening level. The ear height in sitting position
mostly ranges between 1.0 an 1.2 m. We recommend using the original stands, which were
developed especially for this cause.
Stereo Triangle
Minimal distance 1.0 m Distance from walls min 50 cm
Horizontal arrangement between 1.00 m and 1.20 m at ear height in sitting position

Hörzone
RL906
110°-120°
RL906
RL906
RL906
RL906
Surround Operation
Here, the stereo triangle (see Stereo Operation) is extended to an imaginary circle. The
listening zone constitutes the central point of this circle. Please ensure that all loudspeakers
are positioned at the same distance to the listening zone.
The centre loudspeaker should be located in the middle between the two front speakers.
Thanks to its magnetic shield, you can install it above or underneath the TV set, in standing or
lying position, depending on space. Please ensure that the front and rear loudspeakers are
on the same horizontal level, as well.
The angle between the centre and rear loudspeakers should be between 110° - 120°.
If your listening room should not allow such a set-up, most decoder devices allow an
adjustment between the individual loudspeaker distances.
Cable Connection
If the input signal exists only in an asymmetric
way (Cinch), a conversion into a symmetric
signal is necessary.
2
3
1
Cinch
Connector
XLR
Connector
Shield
Cable

500 1k
[Hz]
200
+
-
300
Hz
50 100
0
+2,5
[dB]
-7,5
-5,0
-2,5
-7,5
-5,0
-2,5
5k 10k 20k
[Hz]
2k
+
-
HT
1k
0
+2,5
[dB]
HT Controller
allows subjective adjustment to individual listening habits.
TT Controller
for adjustment according to acoustic room conditions.
300 Hz Controller
allows sound pressure adjustment in the range around 300 Hz on set-up of the console.
Level Controller
This controller allows level adjustment.
Ground Switch
This switch allows the amplifier electronics to be switched ungrounded. This helps to avoid
ground loops (humming), caused by unfavourable cabling.
The marks on the reverse side indicate the linear frequency-response characteristic or
respectively the calibration of the acoustic output level at P = -14 dBu to 83 dB / r=1 m.
40 100 200
-
TT
0
+2,5
[dB]
-7,5
-5,0
-2,5
500 800
[Hz]
Status display on the front side of the loudspeaker
A two-tone LED beneath the tweeter serves as status display.
Green: Unit is switched on, normal operation.
Red: Overload protective circuit is activated; limitation to the maximum allowable output
power is effected.
Control knob on the reverse side of the loudspeaker
Control Range HT Controller
Control Range TT Controller
Control Range 300 Hz Controller
HT TT 300 Hz LEVEL
INPUT
sym. RC
0...+6 dBu
WARNING !
pull power plug
before opening
GROUND
230V~ 50-60Hz
FUSE 1 A T

Specifications
General active two-way monitor for use in small
audio-, video production studios,
in mobile broadcast vans, and for
multi-channel and near-field purposes
Maximum SPL 104 dB / r=1m
Bandwidth 50 Hz...20 kHz ± 3 dB
Calibration:
Acoustic output level / PE= -14 dBu 76 dB / r=1m
Directivity index
from 200 Hz...10kHz increasing from 1.5 to 11 dB
Inherent noise sound level < 7dB / r=1m
Total harmonic distortion
/ measured at 83 dB, r=1m,
from 150 Hz...10 kHz < -40 dB
Nominal input level +6 dBu adjustable
Input impedance > 10 kOhm / symmetrically
Nominal output power
of the MOSFET-amplifier
LF 80 Watt / 4 Ohm
HF 40 Watt / 8 Ohm
Electronic crossover frequencies 3 kHz
Operation and clipping indicator LED on front side
Input connector XLR 3F
Loudspeaker systems
Woofer 130 mm cone
Tweeter 25 mm dome
Temperature requirements
for use +15°C to +35°C
for storage -25°C to +45°C
Humidity 45 - 75 %
Power requirements Europe 230 Volt (±10%), AC, 50 Hz
U.S.A. & Canada 120 Volt, AC, 60 Hz
Power consumption max. 100 Watt at full load
Dimensions (H x W x D) 255 x 180 x 200 [mm]
Weight 5.5 kg
Design of the Cabinet MDF wood, black veneer, different colors optional
Magnetic shield optional

Free field frequency response
Directivity index
Total harmonic distortion P = 83 dB
A
studio techniques - sound reinforcement systems
Nikolaistrasse 7 Tel: [phone]
04643 Geithain / Germany Fax: [phone]
e-mail: [email protected]
www.me-geithain.de
musikelectronic geithain gmbh