MUX AP3220L User manual

– 1 –
Install the AP
a. Install it on the Wall
1. Rotate the bracket onto the T-bar of the ceiling.
2. Push the AP toward the bracket until it snaps into place.
Connect Cables
1. Connect the external cable to the GE/PoE_IN port.
2. Connect the local LAN switch or computer cable to the LAN1 port.
1
2
1. AP3220L access point
2.
3.One pack of screws
Quick Start Guide
2. Push the AP toward the bracket until it snaps into place.
One mounting bracket 4.
Package Contents
150200002388H R01
2
Mode 2: First insert the mounting bracket into the AP then insert the
Documentation— Quick Start Guide
(this document),
Warning:
For indoor use only. The access point and all
1. Fix two screws on the wall and 110 mm apart.
2. Slide the AP’S wall mounting slots down onto the screws so
b. Install it on the Ceiling T-Bar
d. Install it on the Ceiling Bracket
Mode 1: The hole on the back of the access point is threaded into the
cable tie, and secured to the water pipe at the top.
connected cables are not suitable for outdoor use.
Certificate and Warranty card
that the unit is secure.
at the top position.
1. Use the included screws to attach the mounting bracket to the wall.
c. Install it with Cable Ties (with or without bracket)
AP3220L Wireless Access Point
1233 34

Quick Start Guide
– 2 –
Size(WxDxH) 191.0x195.0x44mm
Weight 360g
Temperature Working˖0°C to 45°C
Storage: -20°C to 60°C
Humidity 5% to 95% (No-condensation)
2.4 GHz Radio IEEE 802.11b/g/n
5 GHz Radio IEEE 802.11a/ac/n
PoE GE port supports PoE,
802.3af/at power supply
1 LAN1 port Support 10/100/1000Mbps
1 GE/PoE IN port Support 10/100/1000Mbps
1 Console RJ45 port
1 USB2.0 port 5V/500mA
Check AP LED
1. Power LED— green means normal operation.
2. 2.4G-WiFi and 5G-WiFi LEDs — green means radio enabled.
3
1 Reset button
Port Description
NOMOR:63194/SDPPI/2019 HIDF16000136
ALIBABA CLOUD CON{PUTING CO., LTD
Bt74t040919AE0lA2
This device complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference.
(2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
is encouraged to try to correct the interference by one or more of
thefollowing measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for
an uncontrolled environment and it also complies with Part 15 of
the FCC RF Rules. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for
this transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation
instructions and consider removing the no-collocation statement.
Caution!
responsible for compliance could void the user's authority to
operate the equipment.
Frequency band: 5150 - 5250 MHz:
Indoor use: Inside buildings only. Installations and use inside road
vehicles and train carriages are not permitted. Limited outdoor use:
systems (UAS) is limited to within the 5170 - 5250 MHz band.
Frequency band: 5250 - 5350 MHz:
Indoor use: Inside buildings only. Installations and use in road
vehicles, trains and aircraft are not permitted. Outdoor use is not
permitted.
Frequency band: 5470 - 5725 MHz:
Installations and use in road vehicles, trains and aircraft and use
for unmanned aircraft systems (UAS) are not permitted.
1 DC 12V port 12V DC
Operating frequency
5G
2.4G
Maximum output power
5G
2.4G 2400~2483.5MHz
2402~2480MHz
5150~5350MHz/5~5MHz
20dBm (single chain power)
30dBm (single chain power)
Hereby, MUXI declares that the radio equipment type AP3220L is in
compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet
address: muxi-connect.com.
BLE
BLE 10dBm