XONTEL XT-18AP User manual

XonTel XT-18AP
User Manual

Table of Contents
Declaration…………………………...…………………………………………………..…3
Application Occasions…………………………………………………………………..4
Hardware Connection………….……………………………………………………….5
Software Wizard Configuration …………………………..……………………….6
Network Configuration………….………………………………………….………….10
1 LAN settings…………………………………………………………..……………………………………10
2 WAN settings…………………………………………………………………..…………….……………10
3 Wireless settings…………………………………………………………..………………………….…11
4 DNS settings…………………………………………………………………..……………………..……11
Users Configuration …………………………..…………………………………………12
System Configuration………….…………………………………………………..……12
1 Manage Configuration…………………………………………………………..………………….…12
2 Upgrade…………………………………………………………………..…………………………….……13
3 Reboot…………………………………………………………..……………………………………………13
4 Change Password ………………………………………………………………………………….……14
5 Remote…………………………………………………………..……………………….…………..…….14
6 LED Switch…………………………………………………………………..……………………………..14
7 Time Setting…………………………………………………………..……………………………………15
8 Logs…………………………………………………………..…………………………………………..……15
Firewall Configuration………….………………………………………………….……16
1 IP Filter…………………………………………………………..………………………………..………...16
2 MAC Filter…………………………………………………………………..………………..…………….16
3 URL Filter…………………………………………………………..………………………………………..17
4 Port Forward……………………………………………………………………………..………………..17
5 ARP Binding…………………………………………………………..…………………………….………18
6 DMZ Settings…………………………………………………………………..…………………..………19
7 DDOS protection settings………………………………………………………..…………………..19

Declaration
Copyright © 2020 XonTel Technology Co. All rights reserved.
Without the written permission of XonTel Technology Co., any unit or individual
may not imitate, copy, transcribe or translate part or all of this manual, and it must
not be transmitted in any way (electronic, photocopying, recording, etc.) for profit.
XonTel is a registered trademark of XonTel Technology Co., All other trademarks
or registered trademarks mentioned in this document are the properties of their
respective owners. Product specifications and information mentioned in this
manual are for reference only and are subject to update without notice. Unless
there is a special agreement, this manual is only used as a guide. All statements,
information, etc. in this manual do not constitute any kind of warranty.

Application Occasions
XonTel XT-18AP Access Point can work individually or together with a router. Solution
1 & 2 are for your reference.

Hardware Connection
When first time power on the device, we need to configure it on a PC via a network
cable. Connect XonTel XT-18AP WAN port to the PoE adapter (PoE injector) PoE
port. And then connect its LAN port to a PC. Details shown in the picture.

Software Wizard Configuration
1）Before log in the system, we need to change the PC IP address. Open up the
Control panel - Network and sharing center – Change adapter settings – double
click Ethernet- Properties – Double click IPv4 – change IP address to
192.168.10.10; Subnet Mask to 255.255.255.0; Default Gateway to 192.168.10.1.
2）Open the web browser, enter 192.168.10.1 to the log in page.
3）This is the log in page. Please fill in with the parameters below:
Initial password: xontel

4）After log in, click Wizard and choose Router mode
5）WAN settings: Choose DHCP, and click Next.

6）LAN settings: IP address is free to change. In this manual, we’ll use default
192.168.10.1. Click Next.
7）Wi-Fi 2.4G settings: SSID is also free to change. We can keep Country and
Channel as default. Click Next.

8）Wi-Fi 5.8G settings (Available on dual-band APs): SSID is also free to
change. We can keep Country and Channel as default. Click Next.
9）Click Finish and its done.

Network Configuration
1. LAN settings
From here you can configure Access Point LAN port network settings.
In XT-18AP GUI interface to Network ---→ LAN
2. WAN settings
From here you can configure Access Point WAN port network settings.
In XT-18AP GUI interface to Network ---→ WAN